NiTi(110)表面氧原子吸附的第一性原理研究

为了研究给定的NiTi的表面氧化过程,在保持体系中Ni和Ti原子总数相等的条件下,构建了一系列Ti原子在表面反位的c(2×2)-NiTi(110)缺陷体系,并利用第一性原理计算研究了氧原子在各种NiTi(110)反位缺陷体系的吸附行为以及表面形成能.计算结果表明:吸附氧原子的稳定性与表面Ti原子的富集程度有很大的关联性,体系表面Ti原子富集程度越高,氧原子吸附的稳定性越高;当覆盖度较高时,由于氧原子的吸附,可使Ni和Ti原子在表面出现反位.在富氧条件(μ_o≥-9.35 eV)下,氧原子在表面第1层中的全部Ni原子与第3层全部Ti换位的反位缺陷体系上的吸附最稳定,此时随着氧原子的吸附,表面上的Ti原子升高,导致向上膨胀生长形成二氧化钛层,且在其下方形成富Ni层,由此可合理地解释实验上发现NiTi合金氧化形成二氧化钛层的可能原因.     

The adsorption of molecular oxygen species on Ag(110)

The adsorption of oxygen on the Ag(110) surface was examined at temperatures down to 123 K. In addition to the dissociatively adsorbed state which desorbed at 590 K, a second oxygen state desorbed at 190 K following adsorption at 150 K and below. This high temperature state appeared to form prior to the development of the low temperature state. The ratio of coverages of the two states was a strong function of both exposure and adsorption temperature. Isotopic exchange experiments indicated that the low temperature state was molecularly adsorbed. The desorption of the molecularly adsorbed oxygen exhibited complex kinetics due to interaction with adsorbed oxygen atoms.     

First-principles molecular dynamics study of acetylene adsorption on the Si(001) surface

We present a first-principles molecular dynamics study of acetylene adsorption on the Si(001) surface. Acetylene molecules are di-σ bonded to the first layer Si dimers with the adsorption energy of 64.8 kcal/mol. It is elucidated that the CC bond is essentially double bond and the Si dimer bonds are not cleaved. The normal mode analyses well reproduce the experimental results, giving a strong support to our results.     

第一性原理研究氧在Ni(111)表面上的吸附能及功函数

采用基于密度泛函理论（DFT）广义梯度近似（GGA）下的第一性原理方法系统地研究了不同覆盖度下O在Ni（111）表面的吸附特性.计算结果表明,O在Ni（111）表面的稳定吸附位为三重面心立方（fcc）洞位,吸附能随着覆盖度的增加而减小,O诱导Ni（111）表面功函数的变化量与覆盖度成近线性关系,并随着覆盖度的增加而增大.同时,通过对电子密度和分波态密度的分析发现：O在Ni（111）表面的吸附使得Ni表面电子向O原子转移,形成表面偶极矩,导致功函数增加;表面Ni原子的3d轨道和O的2p轨道通过耦合、杂化作用形成成键态和反键态,而反键态几乎不被占据,因而O—Ni键相互作用比较强,吸附能较大. 关键词： 表面吸附 密度泛函理论 吸附能 功函数     

Phase diagram of molecular oxygen adsorption on the (111) platinum surface

Molecular oxygen adsorption on the Pt(111) surface is studied based on ab initio computations and thermodynamics. An O2 adsorption phase diagram is determined. There are two possible chemisorbed molecular states: one at a bridge site and another one at an fcc hollow site. While some population in the bridge sites persists at all coverages, the states coexist through the intermediate coverage phases. The relative coverage of the two species on the surface is determined by the competition between the Pt lattice distortion energy (that results from O2 adsorption) and the O2 repulsion energy. Our results give a reasonable explanation for the seemingly contradictory findings in previous experimental and theoretical work.     

Sulfur dioxide adsorption and reaction with atomic oxygen on the Ag(110) surface

The adsorption of SO₂ on Ag(110) and the reaction of SO₂ with oxygen adatoms have been studied under ultrahigh vacuum conditions using low energy electron diffraction, temperature programmed reaction spectroscopy and photoelectron spectroscopy. Below 300 K, SO₂ adsorbs molecularly giving p(1×2) and c(4×2) LEED patterns at coverages of one half and three quarter monolayers. respectively. At intermediate coverages, streaked diffraction patterns, similar to those reported for noble gas and alkali metal adsorption on the (110) face of face-centered cubic metals were observed, indicating adsorption out of registry with the surface. A feature at low binding energy in the ultraviolet photoemission spectrum appeared which was assigned to a weak chemisorption bond to the surface via the sulfur, analogous to bonding observed in SO₂-amine charge transfer complexes and in transition metal complexes. SO₂ exhibited three binding states on Ag(110) with binding energies of 41, 53 and 64 kJ mol^?1; no decomposition on clean Ag(110) was observed. On oxygen pretreated Ag(110), SO₂ reacted with oxygen adatoms to form SO_3(a), as determined by X-ray photoelectron spectroscopy. Reacting preadsorbed atomic oxygen in a p(2 × 1) structure with SO₂ resulted in a c(6 × 2) pattern for SO_3(a). The adsorbed SO_3(a) decomposed and disproportionated upon heating to 500 K to yield SO_2(g), SO_4(a) and subsurface oxygen.     

First-principles calculations of ammonia decomposition on Ni(110) surface

First-principles calculations based on density functional theory (DFT) have been performed to study the adsorption and decomposition of NH₃ on Ni(110). The adsorption sites, the adsorption energies, the transition states and the activation energies of the stepwise dehydrogenation of NH₃ and the associative desorption of N are determined, and the zero point energy correction is included, which makes it possible to compute the rate constants of the elementary steps in NH₃ decomposition. Combined DFT calculations and kinetic analysis at 350 K indicate that the associative desorption of N has a reaction rate lower than NH_x dehydrogenation and is therefore the rate determining step. The distinctly different rate constants over Ni(110), Ni(111) and Ni(211) imply that ammonia decomposition over Ni-based catalyst is a structure-sensitive reaction.     

Mechanisms for oxygen adsorption on the Si(110) surface studied by Auger electron spectroscopy

Oxygen adsorption on the Si(110) surface has been studied by Auger electron spectroscopy. For a clean annealed surface chemisorption occurs, with an initial sticking probability of ～6 × 10^?3. In this case the oxygen o_kll signal saturates and no formation of SiO₂ can be detected from an analysis of the Si L_2,3VV lineshape. With electron impact on the surface during oxygen exposure much larger quantities are adsorbed with the formation of an SiO₂ surface layer. This increased reactivity towards oxygen is due to either a direct effect of the electron beam or to a combined action of the beam with residual CO during oxygen inlet, which creates reactive carbon centers on the surface. Thus in the presence of an electron beam on the surface separate exosures to CO showed adsorption of C and O. For this surface subsequent exposure in the absence of the electron beam resulted in additional oxygen adsorption and formation of SiO₂. No adsorption of CO could be detected without electron impact. The changes in surface chemistry with adsorption are detectable from the Si L_2,3VV Auger spectrum. Assignments can be made of two main features in the spectra, relating to surface and bulk contributions to the density of states in the valence band.     

The adsorption of CO and oxygen on Cu layers on a W(110) surface

The adsorption of CO, and to a lesser extent that of oxygen on Cu layers deposited on a W(110) surface has been investigated by thermal desorption. Auger, and XPS measurements. For CO the amount adsorbed decreases monotonically with Cu thickness from 1–5 layers. For O there is a slight increase for 1 layer, followed by a steep decrease up to 4 Cu layers where the amount adsorbed levels off. CO adsorption shifts the core levels of Cu (observed for 1 layer of Cu) to higher binding energy by 0.4 eV; the O 1s level of CO is also shifted to higher binding energy by 1.5 eV, relative to CO/W(110) suggesting that electron transfer from CO occurs but is passed on to the underlying W. For O adsorption there is very little shift in the Cu core levels or in the O 1s level, relative to O/W(110). Thermal desorption of CO at saturation coverage from Cu/W(110) shows desorption peaks at 195, 227 and 266 K, as well as small peaks associated with CO desorption from clean W, namely a peak at 363 K and β-desorption peaks at 1080 and 1180 K. As CO coverage is decreased the 195 and 227 K peaks disappear successively; the W-like peaks remain unchanged in intensity. It is argued that the latter may be due to adsorption on bare W at domain boundaries of the Cu overlayer, while the 190–266 K peaks are associated with adsorption on Cu, but probably involve reconstruction of the Cu layer. For n = 2–8 a single but composite peak is seen, shifting from 180 to 150 K as Cu thickness increases as well as a minor peak at 278 K, which virtually vanishes on annealing the Cu deposit at 850 K. The effect of tungsten electronic structure on the behavior of adsorbates on the Cu overlayers, as well as similar effects in other snadwich systems are discussed.     

S在Pt皮肤Pt3Ni(111)面吸附的第一性原理研究

采用基于密度泛函理论的第一性原理方法,计算并分析了S原子在 Pt皮肤Pt3Ni(111)面不同位置的吸附特性.结果表明：S原子在Pt皮肤Pt3Ni的fcc位吸附最强,吸附能为5. 49 eV;与S原子在纯净Pt(111)表面的吸附相比,S原子在Pt皮肤Pt3Ni表面相应吸附位置的吸附能变小、与近邻的Pt原子形成的S-Pt键变长,表明掺杂的Ni会减小相应位点S原子的吸附能,降低体系对S原子的吸附能力,进而减弱S吸附对体系催化能力的影响;态密度分析发现, S原子的吸附使得Pt基催化剂的催化活性降低,主要是S的2p电子引起的;这些结果将为后续研究Pt基合金电极抗S中毒效果以及探究S原子吸附后Pt3Ni的活性位提供依据.     

Chemisorption of oxygen on the silver (110) surface

In the present work the interaction between oxygen and the silver (110) surface is investigated, mainly using LEED-Auger techniques and thermal desorption spectra. The formation and stability of adsorption layers is studied after exposures at pressures from 10^?3 to 1 torr. At maximum coverage, a (2 × 1) superstructure is formed which is stable up to the desorption temperature. At lower coverage, (3 × 1) and (4 × 1) superstructures are also observed. On the basis of the experimental evidence, tentative models for these structures are presented and discussed.     

The adsorption of sulfur on the tungsten (110) surface

The adsorption and desorption of S on a W(110) surface is studied by Auger electron spectroscopy (AES), low energy electron diffraction (LEED), work function change (δφ) measurements and thermal desorption spectroscopy (TDS). The evolution of the structure with coverage θ is quite different from that reported for S on Mo(110) and — at low coverages — from that of Te on W(110). At low coverages the structure indicates complex lateral interactions. The bonding changes with coverage similar to S on W(100). Evidence for more complex desorption kinetics than assumed in the past is presented.     

Reflectometric study of surface states and oxygen adsorption on clean Si(100) and (110) surfaces

External differential reflection measurements were carried out on clean Si(100) and (110) surfaces in the photon energy range of 1.0 to 3.0 eV at 300 and 80 K. The results for Si(100) at 300 K showed two peaks in the joint density of states curve, which sharpened at 80 K. One peak at 3.0 ± 0.2 eV can be attributed to optical transitions from a filled surface states band near the top of the valence band to empty bulk conduction band levels. The other peak at 1.60 ± 0.05 eV may be attributed to transitions to an empty surface states band in the energy gap. This result favours the asymmetric dimer model for the Si(100) surface. For the (110) surface at 300 K only one peak was found at 3.0 ± 0.2 eV. At 80 K the peak height diminished by a factor of two. Oxygen adsorption in the submonolayer region on the clean Si(100) surface appeared to proceed in a similar way as on the Si(111) 7 × 7 surface. For the Si(110) surface the kinetics of the adsorption process at 80 K deviated clearly. The binding state of oxygen on this surface at 80 K appeared to be different from that on the same surface at 300 K.     

Au(110)表面结构和氧原子吸附的第一性原理研究

用密度泛函理论(DFT)研究了金属Au(110)表面结构以及氧原子的吸附状态.计算得到Au(110)-(1×2)缺列再构表面原子的弛豫分别是-15.0%(Δd₁₂/d₀)和-1.1%(Δd₂₃/d₀),表面能为52.7 meV/²,功函数Φ=5.00 eV;Au(110)-(1×3)缺列再构表面的Δd_{1 关键词： 缺列再构Au(110)表面 STM图像 氧原子吸附}     

Hydrogen adsorption on Pd/TiFe (110) surface

Adsorption of hydrogen on the TiFe (110) surface covered by palladium monolayer was investigated using the full potential linearized augmented plane wave method within the local density approximation. Influence of palladium coating to adsorption properties of the TiFe (110) surface as well as difference it from Pd/TiFe (100) are discussed.     

乙烯在Ni（110）表面吸附的几何结构

用理论计算的方法研究了不同覆盖度的乙烯在Ni（110）表面吸附的位置.乙烯的吸附几何结构在团簇计算中进行了局部优化.在低覆盖度下，单个乙烯分子占据了短桥位和顶位之间的中间位置.乙烯分子的C—C轴大致沿衬底的Ni原子链排列（即沿<110>晶向），C—C轴与衬底Ni（110）表面有10°的倾斜角.乙烯分子的C—C键的键长为0151nm.在高覆盖度下(05ML)，乙烯在Ni (110)上形成了有序的c（2×4）相，在一个表面元胞内的两个乙烯分子的吸附位置类似于低覆盖度时的结果，但乙烯分子的C—C 键键长分别为0142和0143nm.     

Atomic adsorption of oxygen on Cu(111) and Cu(110)

We have studied angle-resolved inverse photoemission ( = 9.7 eV) after room temperature adsorption of oxygen on Cu(111) and Cu(110). On Cu(111) exposure to 500 L induces a band (3.0 eV aboveE _F at) which shows clear dispersion (1.0 eV) to higher energies for off normal incidence. Since no LEED superstructure is seen for that system, our results present strong evidence for the presence of short-range surface order. Two adsorbate bands are identified (2.8 eV and 6.3 eV at) on Cu(110)p(2×1)-O. Our results are in good agreement with a long-bridge adsorption site.     

O2在Mo(001)表面吸附的第一原理研究

采用第一原理方法计算了O2分子在 Mo(001) 表面的吸附,得到了吸附构型的各种参数,并且计算了O2分子在 Mo(001) 表面4个位置（顶位,桥位,穴位垂直,穴位平行）吸附后的能量,结果表明在顶位吸附能最高。通过对O2分子在 Mo(001) 表面吸附的原子轨道电荷分布与态密度图的分析可以看出在吸附过程中主要是O原子的2p轨道电子与钼的4s和4d轨道电子的相互作用。