Properties of Fe–Ga based powders prepared by mechanical alloying

Alloys of Fe–Ga with starting compositions of 17, 19, 21, 23, and 25 at% Ga and Fe₈₁Ga₁₇Z₂ (Z=Si, Sn) have been prepared by mechanical alloying. Samples were milled in a SPEX Model 8000 mill with a ball to sample weight ratio of about 4:1. Phase formation as a function of milling time has been investigated for the 19 at% Ga sample and suggests that milling times of 12 h produce fully alloyed samples. Alloys have been studied by electron microprobe, X-ray diffraction, vibrating sample magnetometery and ⁵⁷Fe Mössbauer effect spectroscopy. Fully milled powders have measured compositions of Fe_100−xGa_x with x=15.7, 17.0, 19.0, 22.4, and 24.0 and Fe_83.1Ga_15.2Z_1.7 (for both Z=Si and Sn). X-ray diffraction showed the presence of a disordered bcc phase with no indication of an ordered D0₃ phase. However, the latter is difficult to observe with X-ray diffraction because of the low intensity of the fcc superlattice peaks. A bimodal Fe hyperfine field distribution as obtained from Mössbauer effect spectra indicated the presence of two discrete Fe environments. The results suggested a lower degree of Ga clustering than has been previously observed in Fe–Ga alloys, of similar composition, prepared by melt spinning. The microstructure is similar to that of Fe–Ga thin films prepared by combinatorial sputtering. Some samples have also been studied after annealing at 800 °C for 8 h. No changes were observed in X-ray diffraction patterns after annealing. However, Mössbauer effect studies show the formation of D0₃ and L1₂ order in annealed samples analogous to the phases observed in melt spun ribbons of similar composition.     

Preparation of nanocrystalline Fe–Ni powders by mechanical alloying used in soft magnetic composites

This paper focuses on the preparation of nanocrystalline Fe–Ni powders by mechanical alloying method, which can be used in soft magnetic composites. Fe–10 wt% Ni and Fe–20  wt % Ni alloys were prepared using a high-energy ball mill. The magnetic properties of samples were measured by a B–H curve analyzer and microstructures of the samples were characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD). The bcc Fe(Ni) phase formation was identified by XRD and completed after 45 h of milling. It was found that higher milling time resulted in, larger lattice parameter, higher microstrains and smaller crystallite sizes. Also, results showed that with increasing the milling time, coercivity increased and saturation intrinsic flux density firstly increased noticeably and then decreased in higher milling times (>70 h).     

共掺杂效应对Y2O3:Eu3+和Gd2O3:Eu3+发光影响的理论研究

通过在Y2O3:Eu3 和Gd2O3:Eu3 发光材料中掺入Li ,Mg2 ,Al3 等离子能有效地提高材料的发光强度,根据分子动力学和密度泛函计算的结果,认为这些离子多倾向于形成C2格位附近的间隙缺陷对,导致部分Y(Gd)-O的键长增加,提高了材料的量子效率的同时使得激发峰位出现红移,是引起材料发光增强的一个原因.     

Infrared photoluminescence and Raman spectra in the Y2O3–ZrO2 system

In this work we present laser-excited infrared photoluminescence and Raman spectra of zirconia with different yttria content (2%–9.5% Y ₂O₃) in order to investigate the effect of dopant on their optical properties. All the Raman spectra were taken over the range 100–800 cm^?1, and the Ar⁺ laser-excited luminescence over the range 16,000–19,000 cm^?1 (absolute frequency). The results are discussed on the basis of defects related to anion vacancies and changes in the disorder degree induced mainly by yttria content in the samples.     

原材料Y2O3的结晶性对Y2O2S:Eu3+发光特性的影响

为进一步提高Y2O2S：Eu^3＋的发光性能,采用改善主要原材料Y2O3结晶性的方法,使Y2O2S：Eu^3＋红色荧光粉在20kV和25kV下发光强度分别增强5％和10％,且不影响色度、粒度、粉体分散性等主要考核指标。提高了粉体的耐电压特性（发射强度与激发电压间的关系特性）。讨论和分析了发射强度增强、电压特性改善的原因：主要原材料Y2O3的结晶性的改善,使得合成的Y2O2S：Eu^3＋具有更好的晶体质量,Eu^3＋离子品场环境得到进一步改善,从而减弱了无辐射过程及因晶格畸变所造成的能量损失,发光效率得到增强,电压特性得刮改善。文验表明,获取高质量多晶Y2O3的最佳分解温度为1400℃左右。     

Electron paramagnetic resonance and photoluminescence properties of α-Al2O3:Cr3+ phosphors

The red emitting Cr³⁺ activated α-Al₂O₃ powder phosphor has been prepared by easy combustion reactions from mixed metal nitrate reactants and urea with ignition temperatures of 500 °C. The as-synthesized powder was characterized by X-ray diffraction, scanning electron microscopy, and Fourier-transform infrared techniques. The X-ray diffraction pattern reveals that the phosphor crystallized in the hexagonal α-Al₂O₃ phase directly from the combustion reaction. The EPR spectrum exhibits an intense resonance signal with effective g value at g=3.33 along with a few weak resonance signals with effective g values at g=13.7, 2.34, 1.95, 1.49, and 1.26. The spin concentration (N) and its paramagnetic susceptibility (χ) have been evaluated. The excitation spectrum consists of two broad intense bands at 415 nm and 555 nm and are assigned to ⁴A_2g (F)→⁴T_1g (F) and ⁴A_2g (F)→⁴T_2g (F) transitions, respectively. The intense fluorescence peak around 691 nm is attributed to ²E _g →⁴A_2g transition of Cr³⁺ ion. By correlating EPR and optical data, the crystal field splitting parameter (Dq), Racah inter-electronic repulsion parameter (B) have been evaluated and discussed. The EPR and optical studies reveal that Cr³⁺ ions are occupying in Al³⁺ sites in octahedral coordination.     

Novel templates directed synthesis of YVO4: Eu3+ (red) and Y2O3–SiO2: Tb3+(green) phosphors

Red/green emissive phosphors YVO₄: Eu³⁺ and Y₂O₃–SiO₂: Tb³⁺ have been synthesized via novel templates direction methods. Photoluminescence studies exhibit the emission intensities as significantly enhanced through pre-encapsulation treatments of designed pyridine amide compounds (YVO₄: Eu³⁺) and 3,4,5-tris(tetradecoxy) benzoic acid (Y₂O₃–SiO₂: Tb³⁺). The as-prepared vanadate particles turn out to be much less agglomerated based on the dispersion by the organic templates. The obtained composite materials, which demonstrate extraordinary fluorescence properties, could be promising candidates for future optoelectronic devices.     

Specific Features of the Local Structure and Transport Properties of ZrO2–Sc2O3–Y2O3 and ZrO2–Sc2O3–Yb2O3 Crystals

Optics and Spectroscopy - The specific features of the local structure of ZrO2–Sc2O3–Y2O3 and ZrO2–Sc2O3–Yb2O3 crystals are revealed by optical spectroscopy using the Eu3+...     

微波热效应合成(Y,Gd)BO3:Eu3+荧光体

本文首次报道用微波热效应法合成(Y,Gd)BO3:EU3+荧光体粉晶材料,X射线粉末衍射确认为六方晶系,晶胞参数a=0.3796nm,c=0.8835nm;在589nm和613.0nm监测下,其激发光谱峰是239.0nm和240.0nm,半高宽40nm.在240.0nm激发下,589nm和612-626nm的荧光强度比为1.9/1.     

Eu3+在Y2O3-Bi2O3体系中发光性能的研究

Y2O3:Eu3+磷光体中的Eu3+在6100Å附近呈现很强的尖峰发射.这个磷光体虽然在阴极射线和短波紫外光(约2500Å激发下是十分有效的,但是对于长波紫外光激发却很不灵敏.Datta[2]於1967年报导在Y2O3:Eu3+磷光体中加入少量Bi3+,在3650Å长波紫外光激发下可增强Eu3+在6100Å的尖峰发射强度.     

151Eu Mössbauer study of luminescent Y2O3:Eu3 + core-shell nanoparticles

¹⁵¹Eu Mössbauer spectroscopy was applied to distinguish among different Eu microenvironments and phases in spherical Y₂O₃:Eu^3?+? and core-shell Y₂O₃@Eu^3?+? phosphor nanoparticles prepared by using homogeneous precipitation method. ¹⁵¹Eu isomer shift revealed that Eu atoms exist only in oxidation state Eu^3?+? in all spherical and core-shell phosphors. Significant differences have been found between the Mössbauer parameters (isomer shift, principal component of EFG and linewidth) characteristic of spherical Y₂O₃:Eu^3?+? and core-shell Y₂O₃@Eu^3?+? phosphor nanoparticles. The Mössbauer parameters of spherical Y₂O₃:Eu^3?+? were associated with Eu substituting Y in the Y₂O₃, while Mössbauer parameters of core-shell Y₂O₃@Eu^3?+? phosphor were attributed to Eu being in the Eu₂O₃ shell, proving the structural model and the successful preparation of these phosphors.     

Low-temperature photoluminescence spectra of CdO–In2O3 thin films prepared by sol–gel

(CdO)_1?x–(InO_3/2)_x thin films were deposited on glass substrates by the sol–gel method. The precursor solutions for the mixed oxide films were obtained from the mixture of the precursor solutions for CdO and In₂O₃ prepared separately. The investigated In atomic concentrations in the solution, x, were 0.0, 0.16, 0.33, 0.50, 0.67, 0.84, and 1. X-ray diffraction measurements showed that the films were mainly constituted of CdO, In₂O₃, and CdIn₂O₄. CdO and In₂O₃ were obtained for x=0 and 1, respectively. For x=0.67, which is the stoichiometric composition of the CdIn₂O₄ compound, only this oxide was formed. CdO and CdIn₂O₄ crystals were obtained in the Cd-rich region, whereas In₂O₃ and CdIn₂O₄ crystals were formed in the In-rich region. The PL spectra at 15 K for CdO showed the presence of two main emission bands at energies close to 2.2 and 3.0 eV. A blue-shift of these bands took place for increasing In concentration, which is related to the increase in the band gap energy of the mixed system in going from CdO, with a band gap energy of 2.46 eV, to CdIn₂O₄, with 3.2 eV, to In₂O₃, with 3.6 eV.     

Thermal stability and photoluminescence property of hexagonal MoO3·0.55H2O microrods

The metastable phase of well-faceted, hexagonal, prism-like molybdenum oxide hydrate (MoO₃·0.55H₂O) was successfully synthesized by evaporating molybdic acid solution prepared through cation membrane electrolysis of Na₂MoO₄·2H₂O aqueous solution. The obtained crystals were characterized by X-ray diffraction (XRD), thermogravimetric (TG), scanning electronic microscopy (SEM) and photoluminescence (PL) spectrophotometry. The as-prepared MoO₃·0.55H₂O rods were of 2–4 μm in width and 5–12 μm in length. The MoO₃·0.55H₂O microrods displayed photoluminescence properties at room temperature and were transformed into stable orthorhombic α-MoO₃ after air annealing at 380 °C. Moreover, the influence of temperature factor on the phase transformation process, morphology and photoluminescence properties of MoO₃·0.55H₂O was investigated in detail.     

Structural and phase transition of α-Al2O3 powders obtained by co-precipitation method

Aluminium oxide has been synthesized by co-precipitation technique at different annealing temperature. Powder XRD confirms the formation of α-Al₂O₃ with rhombohedral crystal structure having lattice constant a = 4.76 Å and b = 12.99 Å by the Scherer formula, the average crystallite size is estimated to be 66 nm. The scanning electron microscope results expose the fact that the α-Al₂O₃ nanomaterials are seemingly porous in nature and highly agglomerated. Chemical composition of aluminium oxide is confirmed by energy dispersive spectroscopy. The molecular functional group is confirmed by FTIR. Optical absorption of α-Al₂O₃ has been studied in the UV–vis region and its direct band gap is estimated to be 5.97 eV. This study involves the structural and phase transition of Al₂O₃ and also indicates that α-Al₂O₃ has considerable properties, deserving further investigation for the energetic materials with excellent properties for the possibility of using thin-layer α-Al₂O₃ as a thermo luminescence material.     

Structure and photoluminescence of β-Ga2O3:Eu nanofibers prepared by electrospinning

Eu³⁺-doped β-Ga₂O₃ nanofibers were fabricated by electrospinning. The influence of Eu³⁺ concentration on the photoluminescence properties of the obtained nanofibers was investigated. The morphology and structure of β-Ga₂O₃:Eu³⁺ were characterized by field emission scanning electron microscopy (FE-SEM), X-ray diffraction (XRD) and Raman spectra. The diameter of the Eu³⁺-doped β-Ga₂O₃ nanofibers was in the range of 180-300 nm. When the β-Ga₂O₃:Eu³⁺ nanofibers were excited by 325 nm wavelength, the main emission peak of the samples was 620 nm (⁵D₀→⁷F₂), which corresponded to a typical red emission (⁵D₀→⁷F_j (j = 1, 2, 3, 4) intra-4f transitions of Eu³⁺ ions). In addition, the concentration quench effect and energy transfer mechanism in β-Ga₂O₃:Eu³⁺ were also discussed.     

Surface treatment investigation and luminescence properties of SiO2-coated Ca2BO3Cl:0.02Eu2+ phosphors via sol–gel process

SiO₂-coated Ca₂BO₃Cl:Eu²⁺ phosphors were prepared by the sol–gel method in order to enhance the chemical and thermal stabilities of Ca₂BO₃Cl:Eu²⁺ phosphor. The phase structures, microstructures and luminescence properties were studied by the X-ray diffraction (XRD), scanning electron microscopy (SEM) and fluorescence spectrometer, respectively. The emission intensity of SiO₂-coated Ca₂BO₃Cl:Eu²⁺ phosphor decreased a little compared to that of the uncoated phosphor. The moisture resistances of the phosphors were comparatively examined by the aging treatment experiment in the water, and the thermal stability was studied by the temperature dependent photoluminescence spectra. The results indicated that SiO₂ coating on the surface of the phosphor particles improved the moisture-resistance and thermal stability to a large extent.     

Synthesis,structural and optical properties of Eu3+–doped Ca2V2O7 nanophosphors

Europium doped calcium pyrovanadate nanoparticles Ca₂V₂O₇:Eu³⁺, having a size of 57–63 nm, were synthesized using combustion process. Structure, morphological and optical properties of nanophosphors have been characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), fluorescence spectrometry (PL) and Fourier transform infra-red (FT-IR) spectroscopy. X-ray studies shows that a pure triclinic Ca₂V₂O₇ phase was obtained at 900 °C temperature. The red emission observed at 620 nm upon excitation at 305 nm is due to hypersensitive transition ⁵D₀ → ⁷F₂ of luminescent activator Eu³⁺ location at a site with no inversion symmetry in Ca₂V₂O₇ crystal lattice. High luminescent intensity and easy synthesis technique make this red phosphor a promising candidate for application as luminescent materials.     

Microstructural evolution and thermal stability of Fe–Zr metastable alloys developed by mechanical alloying followed by annealing

The effect of Zr (up to 1 at.%) addition on the formation of Fe–Zr metastable alloys and their thermal stability were investigated for their possible nuclear applications. Fe–xZr (x = 0.25, 0.5, 1%) alloys were synthesised by mechanical alloying under a high-purity argon atmosphere using stainless steel grinding media in a SPEX 8000M high energy mill. The milling was conducted for 20 h with a ball-to-powder weight ratio of 10:1. The formation of metastable solid solutions after milling was confirmed from the change in the Gibbs free energy analysis as per Miedema’s model. The microstructural characterisation was carried out by analysis of X-ray diffraction, atomic force microscopy and transmission electron microscopy. The effect of Zr on the thermal stability of Fe–Zr alloys was investigated by extensive annealing experiments followed by microstructural analysis and microhardness measurements. The stabilisation was found to occur at 800 °C and thereafter, no significant change in the crystallite size was observed for the samples annealed between 800 and 1200 °C. The supersaturated solid solution, especially 1% Zr alloy, found to be highly stable up to 800 °C and the microhardness value of the same measured to be as high as 8.8 GPa corresponding to a crystallite size of 57 nm. The stabilisation effect has been discussed in the light of both the thermodynamic and kinetic mechanisms and the grain size stabilisation is attributed to the grain boundary segregation of Zr atoms and/or Zener pinning by nanoscale precipitation of the Fe₂Zr phase.