Ultrasonic synthesis and photocatalytic characterization of H3PW12O40/TiO2 (anatase)

A novel H₃PW₁₂O₄₀/TiO₂ (anatase) composite photocatalyst was prepared by a high-intensity ultrasonic method using a lower temperature (80 °C) and was characterized by XRD and FT-IR. Its photocatalytic activity, using solar light, was evaluated through the degradation of organic dye methylene blue (MB) in aqueous. When MB solution (50 mg/l, 200 ml) containing H₃PW₁₂O₄₀/TiO₂ (anatase) (0.4 g) was degraded by solar irradiation after 90 min, the removal of concentration and TOC of MB reached 95% and 73%, respectively. The photocatalyst activity of H₃PW₁₂O₄₀/TiO₂ (anatase) was much higher than TiO₂ which was prepared in the same way. H₃PW₁₂O₄₀/TiO₂ remained efficient after five repeated experiments.     

Preparation and photoelectrochemical performance of Ag/graphene/TiO2 composite film

By dipping-lifting in sol-gel solution and reducing process, the graphene/TiO₂ composite film on the glass plate was first prepared. Then, the Ag/graphene/TiO₂ composite film was fabricated by interface reaction with AgNO₃ and N₂H₄·H₂O on the surface of graphene/TiO₂ composite film. The characterization results show that the uniform porous TiO₂ film is made up of the anatase crystal, and the Ag/graphene/TiO₂ composite film is constructed by doping or depositing graphene sheets and Ag nanoparticles on the surface of TiO₂ film. The photoelectrochemical measurement results indicate that the Ag/graphene/TiO₂ composite film has an excellent photoelectrochemical conversion property.     

Preparation and photocatalytic activity of bicrystal phase TiO2 nanotubes containing TiO2-B and anatase

Bicrystal phase TiO₂ nanotubes (NTS) containing monoclinic TiO₂-B and anatase were prepared by the hydrothermal reaction of anatase nanoparticles with NaOH aqueous solution and a heat treatment. Their structure was characterized by XRD, TEM and Raman spectra. The results showed that the bicrystal phase TiO₂ NTS were formed after calcining H₂Ti₄O₉·H₂O NTS at 573 K. The bicrystal phase TiO₂ NTS exhibit significantly higher photocatalytic activity than the single phase anatase NTS and Dessuga P-25 nanoparticles in the degradation of Methyl Orange aqueous solution under ultraviolet light irradiation, which is attributed to the large surface and interface areas of the bicrystal phase TiO₂ NTS.     

Temperature-induced changes in morphology and structure of TiO2-Al2O3 fibers

Electrospinning of a sol-gel and polymer mixture is used to produce titania-alumina (TiO₂-Al₂O₃) fibers with diameters ranging from 200 to 800 nm. These composite metal-oxide fibers were calcined at various temperatures and their morphology is studied using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The decrease in the average diameter of the fibers with increasing temperature is observed. Powder X-ray diffraction (XRD) reveals that up to 800 °C the composite fibers have anatase titania structure whereas at 900 °C the fibers exhibit mixture of anatase and rutile phases. It is found that specific surface area decreases as a function of temperature in the 700-900 °C range. The change in phase (anatase-to-rutile) and the increase in crystallite size occur simultaneously. The presence of smaller amount of amorphous alumina in the primarily titania-based structure seems to play the role in stabilizing the anatase phase.     

TiO2/carboxylate-rich porous carbon: A highly efficient visible-light-driven photocatalyst based on the ligand-to-metal charge transfer (LMCT) process

A novel visible-light-driven photocatalyst based on TiO₂/carboxylate-rich porous carbon composite (TiO₂/CRPC) was successfully synthesized by low temperature carbonization process in air. Sodium gluconate plays a crucial role in the formation of TiO₂/CRPC. Different functional groups of sodium gluconate play synergetic roles in the formation of TiO₂/CRPC. XRD and Raman spectra studies indicated that there are two different TiO₂ crystalline phases existing in TiO₂/CRPC, which are anatase and brookite, and the CRPC is amorphous. Via FT-IR and XPS spectra investigations, it was demonstrated that carboxylate group, the ligand-to-metal charge transfer (LMCT) forming functional group, was solidified into the CRPC and form the LMCT complex on TiO₂ surface through the fabrication of TiO₂/CRPC. Compared with the pure TiO₂, TiO₂/CRPC exhibit enhanced absorption in the UV and visible light region around 260–600 nm. The strong absorption in the visible light region gives TiO₂/CRPC advantages over pure TiO₂ for the degradation of organic pollutants. TiO₂/CRPC can activate O₂ in air under mild conditions and exhibit excellent visible-light-driven photocatalytic activities. However, TiO₂/C composite obtained by using glucose instead of sodium gluconate exhibits poor photocatalytic activity, which demonstrated that carboxylate–TiO₂ complexes are responsible for the prominent photocatalytic properties of TiO₂/CRPC under visible light irradiation.     

Optical properties of TiO2 anatase - Carbon nanotubes composites studied by cathodoluminescence spectroscopy

Luminescence spectra obtained by electron bombardment (cathodoluminescence, CL) on TiO₂ (anatase)/carbon nanotubes (CNT) composite, show only one visible band at 498 nm, while the spectra taken from pure anatase samples show two bands at 498 and 545 nm. We demonstrate that the visible luminescence bands are originated by TiO₂ surface defects due to oxygen vacancies, and that this luminescence signal is independent of TiO₂ mineral form (anatase or rutile). Moreover we obtain that the 545 nm band quenching in TiO₂/CNT composites is caused by empty oxygen vacancies (OV) related to oxygen given from oxygen-rich pristine powder of carbon nanotubes. Our conclusions are also supported by X-ray photoelectron spectroscopy (XPS), SEM analysis and energy dispersed X-ray measurements (EDX). Furthermore we can confirm that the NIR TiO₂ luminescence emission is linked only to the presence of Ti rutile form as described in several works in literature.     

Preparation of silver nanowires coated with TiO2 using chemical binder and their applications as photoanodes in dye sensitized solar cell

In this study, the core–shell structured Ag@TiO₂ wire was prepared for application to dye-sensitized solar cell (DSSC). The Ag nanowire, having an excellent electrical conductivity, was synthesized by using the facile microwave-assisted polyol reduction process. The diameter and length of Ag wires were 40–50 nm and 20–30 μm, respectively, and the face-centered cubic silver crystal structure was obtained. In the presence of 2-mercaptoethanol as a chemical binder, the entire surface of Ag wire was coated with the TiO₂ shell, which has thickness of 20 nm, through solvothermal method. The crystalline structure of TiO₂ shell was the anatase phase possessing an advantage to achieve the high efficiency in DSSC. The core–shell structured Ag@TiO₂ wire exhibited the high thermal stability. The high conversion efficiency (5.56%) in fabricated device with Ag@TiO₂ electrode, which is about 10% higher than reference cell, was achieved by enhancement of short-current density (J_sc) value. The core–shell structured Ag@TiO₂ wire could effectively reduce the charge recombination through the contribution to electron shortcut for improvement in the electron transfer rate and lifetime.     

A novel non-thermal process of TiO2-shell coating on Fe3O4-core nanoparticles

In this work magnetite (Fe₃O₄) nanoparticles coated with titanium dioxide (TiO₂) were prepared by a novel non-thermal method. In this method, magnetite and pure TiO₂ (anatase) nanoparticles were individually prepared by the sol–gel method. After modifying the surface of magnetite nanoparticles by sodium citrate, titanium dioxide was coated on them without using conjunction or heat treatment to obtain Fe₃O₄:TiO₂ core–shell nanoparticles. XRD, EDX, SEM, TEM and VSM were used to investigate the structure, morphology and magnetic properties of the samples. The average crystallite size of the powders was measured by Scherrer's formula. The results obtained from different measurements confirm the formation of Fe₃O₄:TiO₂ core–shell nanoparticles with a decrease in saturation magnetization. Hysteresis loops of the core–shell nanoparticles show no exchange bias effects, which confirms that there is no interaction or interdiffusion at the interface.     

Fabrication and characterization of silver/titanium dioxide composite nanoparticles in ethylene glycol with alkaline solution through sonochemical process

This paper aims to study fabrication and characterization of silver/titanium oxide composite nanoparticle through sonochemical process in the presence of ethylene glycol with alkaline solution. By using ultrasonic irradiation of a mixture of silver nitrate, the dispersed TiO₂ nanoparticle in ethylene glycol associated with aqueous solution of sodium oxide yields Ag/TiO₂ composite nanoparticle with shell/core-type geometry. The powder X-ray diffraction (XRD) of the Ag/TiO₂ composites showed additional diffraction peaks corresponding to the face-centered cubic (fcc) structure of silver crystallization phase, apart from the signals from the cores of TiO₂. Transmission electron microscopy (TEM) images of Ag/TiO₂ composites, which average particle size is roughly 80 nm, reveal that the titanium oxide coated by Ag nanoparticle with a grain size of about 2–5 nm. Additionally, the formation of silver nanoparticles on TiO₂ was monitored by ultraviolet visible light spectrophotometer (UV–Vis). As measured the optical absorption spectra of as-synthesized Ag nanoparticle varying with time, the mechanism of surface formatting silver shell on the cores of TiO₂ could be explored by autocatalytic reaction; the conversion of Ag particle from silver ion is 98% for the reaction time of 1000 s; and the activity energy of synthesizing Ag nanoparticles on TiO₂ is 40 kJ/mol at temperature ranging from 5 to 25 °C. Hopefully, this preliminary investigation could be used for mass production of composite nanoparticles assisted by ultrasonic chemistry in the future.     

Photoactive materials prepared by homogeneous hydrolysis with thioacetamide: Part 2—TiO2/ZnO nanocomposites

Photocatalytic active titanium dioxide (TiO₂)/zinc oxide (ZnO) composite was prepared by homogeneous hydrolysis of a mixture of titanium oxo-sulphate and zinc sulphate in aqueous solutions with thioacetamide and subsequent annealing at the temperature of 600 °C. The prepared samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and high-resolution transmission microscopy (HRTEM). Nitrogen adsorption-desorption was used for surface area (Brunauer-Emmett-Teller—BET) and porosity determination. The photoactivity of the prepared TiO₂/ZnO samples was assessed by the photocatalytic decomposition of Orange II dye in an aqueous slurry under irradiation of 254 and 365 nm wavelengths. Under the same conditions, the photocatalytic activity of a commercially available photocatalyst (Degussa P25), the pure anatase TiO₂ nanoparticles and cubic ZnO were examined.     

Anatase TiO2 films fabricated by pulsed laser deposition using Ti target

TiO₂ films were prepared by pulsed laser deposition using a metallic Ti target in an O₂ gas ambient. The microstructure along with optical and photocatalytic properties of the deposited films were systematically studied by changing the deposition parameters and substrates. It was found that TiO₂ films having nearly pure anatase phase grew effectively in O₂ atmosphere. When the films were fabricated at a substrate temperature of 400°C, their phase structures were greatly affected by the O₂ gas pressure, and nearly pure anatase phase with typical (101) and (004) peaks can be obtained under an O₂ pressure of 15 Pa. For the deposition at 700°C, the crystal structure of the TiO₂ films exhibited a strong anatase (004) peak and was inert to the oxygen pressures. Two modes, namely a substrate-temperature-controlled mode and an oxygen-pressure-controlled mode, were considered for the growth of the anatase TiO₂ films under different substrate temperatures. In addition, the optical and photocatalytic properties were found to be sensitive to both the microstructure and grain size of the TiO₂ films.     

Preparation and characterization of iodine-doped mesoporous TiO2 by hydrothermal method

Iodine-doped mesoporous TiO₂ (I/TiO₂) was prepared by hydrothermal method, using tetrabutyl titanate as precursor, potassium iodate as iodine sources. The as-prepared I/TiO₂ catalysts were characterized by UV-vis, XRD, TEM, BET, TG/DTA, XPS and photoluminescence (PL) spectroscopy. Production of OH radicals on the I/TiO₂ surface was detected by the PL technique using terephthalic acid as a probe molecule. The effects of hydrothermal reaction temperature, calcination temperature and iodine doping content on the structure and properties of the catalysts were investigated. The results showed that iodine-doped TiO₂ calcinated at 300 °C have good anatase crystal. The optimal hydrothermal conditions have been determined to be that reaction temperature 120 °C, calcinated temperature 300 °C and added 1.16 mmol iodine dopants. The average particle size of I/TiO₂ synthesized under optimal condition (I-3 sample) is about 3.9 nm. The I-3 photocatalyst contains 100% anatase crystalline phase of TiO₂. BET specific surface area of I-3 sample is184.8 m² g⁻¹ and is 3.67 times that of pure TiO₂ (50.37 m² g⁻¹). Iodine in I/TiO₂ catalyst mainly exists in the form of I₂, and photoactivity of I/TiO₂ catalyst in visible light comes from photosensitize of I₂. I/TiO₂ catalysis shows very high efficiency for the degradation of phenol under visible light.     

Preparation and characterization of low density polystyrene/TiO2 core–shell particles for electronic paper application

In order to reduce the density mismatch between TiO₂ and the low dielectric medium and improve the dispersion stability of the electrophoretic particles in the low dielectric medium for electrophoretic display application, polystyrene/titanium dioxide (PS/TiO₂) core–shell particles were prepared via in-situ sol–gel method by depositing TiO₂ on the PS particle which was positively charged with 2-(methacryloyloxy)ehyl trimethylammonium chloride (DMC). The morphology and average particle size of PS/TiO₂ core–shell particles were observed by transmission electron microscopy (TEM), scanning electron microscope (SEM) and particle size analyzer. It was found that density of PS/TiO₂ core–shell particles were reduced obviously and the particles can suspend in the low dielectric medium of low density. The PS/TiO₂ core–shell particles can endure ultrasonic treatment because of the interaction between TiO₂ and PS. Zeta potential and electrophoretic mobility of the fabricated core–shell particles in a low dielectric medium with charge control agent was measured to be −44.3 mV and −6.07 × 10⁻⁶ cm²/Vs, respectively, which presents potential in electronic paper application.     

The electrical conductivity properties of polythiophene/TiO2 nanocomposites prepared in the presence of surfactants

A composite of polythiophene (PT) and nano-titanium dioxide (TiO₂), possessing core–shell structure, was synthesized via oxidative polymerization of thiophene using FeCl₃ in the presence of three different surfactants: anionic, cationic, and nonionic. The morphology of the obtained composite materials was investigated by SEM, proving the core–shell structure of the prepared nanocomposite. The formation and thermal stability of the PT onto TiO₂ nanoparticles were confirmed by FTIR and TGA analyses, respectively. XRD data show all of composite materials were amorphous structures. The electrical properties of the nanocomposites were investigated in the presence of surfactant materials, and the best semiconductor property was observed for PT/TiO₂-anionic system. This difference in the conductivity has been attributed to differences in the stability of the composites.     

Morphology and natural wettability properties of sol-gel derived TiO2-SiO2 composite thin films

Previous studies suggest that granular interfaces induce a natural and persistent super-hydrophilicity in TiO₂-SiO₂ composite thin films deposited by sol-gel route. This effect enables to consider self-cleaning applications that do not require a permanent UV exposure, whereas such a permanent exposure is necessary for pure TiO₂ films. In this study, TiO₂-SiO₂ composite thin films have been deposited from a TiO₂ anatase crystalline suspension and different SiO₂ polymeric sols. Wettability studies show that a suitable control of the TiO₂-SiO₂ mixed sol formulations noticeably enhances persistence of the natural super-hydrophilicity in composite films. It is shown that, beside granular interface effects, modifications in the composite film morphologies can noticeably influence wettability properties.     

ZnO/TiO2 core–shell nanowire arrays for enhanced dye-sensitized solar cell efficiency

We present a new method of synthesizing ZnO/TiO₂ core–shell nanowire (NW) arrays for the fabrication of dye-sensitized solar cells (DSSCs). Vertically aligned ZnO NW arrays were obtained on Si substrates, and modified by a TiO₂ shell in order to solve the recombination problems via a cost-effective spin-coating method. The structure of the ZnO/TiO₂ composite NW arrays was characterized. The experimental results indicate that the TiO₂ shell enhances the performance of the DSSCs, through improving the stability of the ZnO NWs and decreasing the recombination of photogenerated electrons on the NW surface. The highest overall conversion efficiency of the cell reaches about 3.0 %.     

Fabrication of belt-like VO2(M)@C core-shell structured composite to improve the electrochemical properties of VO2(M)

VO₂(M) nanobelts encapsulated into carbon core–shell structured composite (VO₂(M)@C) was successfully synthesized by the thermal treatment with the precursor V₃O₇·H₂O@C composite under the inert atmosphere. The as-obtained sample was characterized by XRD, EDS, EA, FT-IR, Raman, SEM and TEM measurements. The core exhibited monoclinic phase VO₂(M) and the carbon coated on the surface of VO₂(M) was amorphous. The average thickness of carbon was about 18.5 nm. The possible formation mechanism of VO₂(M)@C was proposed as that the reaction underwent the solid state reaction by the interface reaction between V₃O₇ core and carbon shell. Furthermore, VO₂(M) and VO₂(M)@C composite were explored as the cathode materials to apply in lithium-ion batteries, indicating that the VO₂(M)@C composite electrode exhibited the better electrochemical properties than that of pure VO₂(M), achieving the aim of improving the electrochemical properties of VO₂(M).     

Low-temperature preparation of anatase titania-coated magnetite

A composite photocatalyst with an anatase titania shell and a magnetite core was prepared in a novel way at low temperature (75 °C at most) by coating photoactive titanium dioxide onto a magnetic Fe₃O₄ core. The photocatalytic activity of the prepared photocatalyst was evaluated by the degradation of model contaminated water of phenol and compared to single-phase titania (either Degussa P25 or prepared titania without magnetic Fe₃O₄). The results showed that the photoactivity was slightly depressed. Then, a remarkable improvement in photoactivity was achieved by modifying the photocatalyst with a SiO₂ layer between the Fe₃O₄ core and TiO₂ shell. The repetitive using of the modified photocatalyst was also investigated, and experimental results illustrated that the photocatalytic-degraded ratio of phenol was still higher than 80% after six cycles.     

Visible-light-activated Ce-Si co-doped TiO2 photocatalyst

To enhance the visible photocatalytic activity and thermal stability of TiO₂, Ce-Si co-doped TiO₂ materials were synthesized through a nonaqueous method of which the purpose was to reduce the aggregation between TiO₂ particles. The obtained materials maintained anatase phase and large surface area of 103.3 m² g⁻¹ even after calcined at 800 °C. The XPS results also indicated that Si was weaved into the lattice of TiO₂, and Ce mainly existed as oxides on the surface of TiO₂ particles. The doped Si might enhance surface area and suppress transformation from anatase to rutile, while the doped Ce might cause visible absorption and inhibit crystallite growth during heat treatment. Evaluated by decomposing dye Rhodamine B, visible photocatalytic activity of Ce-Si co-doped TiO₂ was obviously higher than that of pure TiO₂ and reached the maximum at Ce and Si contents of 0.5 mol% and 10 mol%.     

Effect of Er doping on optical band gap energy of TiO2 thin films prepared by spin coating

In order to evaluate the effect of Er doping in the range of 0–1.0 mol% on optical indirect band gap energy (E_g) of the film, the Er-doped TiO₂ (Er-TiO₂) thin films were spin-coated onto fluorine-doped SnO₂ coated (FTO) glasses. Glancing angle X-ray diffraction (GAXRD) results indicated that the films whose thickness was 550 nm consisted of pure anatase and FTO substrate. The anatase (101) TiO₂ peaks became broader and weaker with the rise in Er content. The apparent crystallite size decreased from 12 nm to 10 nm with increasing the amount of Er from 0 mol% to 1.0 mol%. UV–vis spectrophotometry showed that the values of E_g decreased from 3.25 eV to 2.81 eV with the increase of Er doping from 0 to 0.7 mol%, but changed to 2.89 eV when Er content was 1.0 mol%. The reduction in E_g might be attributed to electron and/or hole trapping at the donor and acceptor levels in the TiO₂ band structure.