The effect of series resistance and interface states on the frequency dependent C–V and G/w–V characteristics of Al/perylene/p-Si MPS type Schottky barrier diodes

The capacitance–voltage–frequency (C–V–f) and conductance–voltage–frequency (G/w–V–f) characteristics of Al/perylene/p-Si Schottky barrier diodes (SBDs) fabricated with spin coating system have been investigated in the frequency range of 30 kHz–2 MHz at room temperature. In order to elucidate the electrical characteristics of SBDs with perylene interface, the voltage and frequency dependent series resistance (R_s), frequency dependent density distribution profile of interface state (N_ss) were obtained. The measurements of C and G/w were found to be strongly dependent on bias voltage and frequency for Al/perylene/p-Si SBDs. For each frequency, the R_s–V plot gives a peak, decreasing with increasing frequencies. Also, it has been shown that the interface states density exponentially decreases with increasing frequency. The C–V–f and G/w–V–f characteristics confirm that the N_ss and R_s of the diode are important parameters that strongly influence the electric parameters in metal/polymer/semiconductor (MPS) structure.     

The effect of interface states, excess capacitance and series resistance in the Al/SiO2/p-Si Schottky diodes

The current-voltage (I-V) characteristics of Al/SiO₂/p-Si metal-insulator-semiconductor (MIS) Schottky diodes were measured at room temperature. In addition the capacitance-voltage (C-V) and conductance-voltage (G-V) measurements are studied at frequency range of 10 kHz-1 MHz. The higher value of ideality factor of 3.25 was attributed to the presence of an interfacial insulator layer between metal and semiconductor and the high density of interface states localized at Si/SiO₂ interface. The density of interface states (N_ss) distribution profile as a function of (E_ss − E_v) was extracted from the forward bias I-V measurements by taking into account the bias dependence of the effective barrier height (Φ_e) at room temperature for the Schottky diode on the order of ≅4 × 10¹³ eV⁻¹ cm⁻²_. These high values of N_ss were responsible for the non-ideal behaviour of I-V and C-V characteristics. Frequency dispersion in C-V and G-V can be interpreted only in terms of interface states. The N_ss can follow the ac signal especially at low frequencies and yield an excess capacitance. Experimental results show that the I-V, C-V and G-V characteristics of SD are affected not only in N_ss but also in series resistance (R_s), and the location of N_ss and R_s has a significant on electrical characteristics of Schottky diodes.     

Effect of series resistance and interface states on the I-V, C-V and G/ω-V characteristics in Au/Bi-doped polyvinyl alcohol (PVA)/n-Si Schottky barrier diodes at room temperature

The forward and reverse bias current-voltage (I-V), capacitance-voltage (C-V) and conductance-voltage (G/ω-V) characteristics of the Au/PVA (Bi-doped)/n-Si Schottky barrier diodes (SBDs) have been investigated at room temperature by taking the interface states (N_ss) and series resistance (R_s) effects into account. The voltage dependent profiles of resistance (R_i) were obtained from both the I-V and C/G-V measurements by using Ohm’s Law and Nicollian methods. The obtained values of R_i with agreement each other especially at sufficiently high bias voltages which correspond the value of R_s of the diode. Therefore, the energy density distribution profile of N_ss was obtained from the forward bias I-V data taking the bias dependence of the effective barrier height (BH) Φ_e and R_s into account. The high value of ideality factor (n) was attributed to high density of N_ss and interfacial polymer layer at metal/semiconductor (M/S) interface. In order to examine the frequency dependence of some of the electrical parameters such as doping donor concentration (N_D), Φ_e, R_s and N_ss values, C-V and G/ω-V measurements of the diode were performed at room temperature in the frequency range of 50 kHz-5 MHz. Experimental results confirmed that the N_ss, R_s and interfacial layer are important parameters that influence electrical characteristics of SBD.     

Investigation of the interface trap density and series resistance of a high-k HfO2-based MOS capacitor: before and after 50 MeV Li3+ ion irradiation

This is the first investigation on the effects of 50 MeV Li³⁺ ions on interface trap density (D _it) and series resistance (R _s), which reveal the improvement of the dielectric properties of RF-sputtered HfO₂-metal oxide semiconductor (MOS) capacitors. The samples were irradiated and characterized at room temperature. The D _it and R _s were determined from the capacitance–voltage (C–V) and conduction–voltage (G–V) characteristics at 1 MHz. The measured capacitance and conductance were corrected for series resistance. It is found that the series resistance of Al/HfO₂/p? Si MOS capacitors increases with ion fluence, calculated at a strong accumulation region before and after irradiation. The interface state density of MOS devices before and after irradiation is found to decrease with increasing ion fluence.     

Two diodes model and illumination effect on the forward and reverse bias I–V and C–V characteristics of Au/PVA (Bi-doped)/n-Si photodiode at room temperature

The forward and reverse bias current–voltage (I–V), capacitance/conductance–voltage (C/G–V) characteristics of the fabricated Au/PVA (Bi-doped)/n-Si photodiode have been investigated both in dark and under 250 W illumination intensity at room temperature. The energy density distribution profile of N_ss was extracted from the forward bias I–V measurements by taking the voltage dependence of effective barrier height (Φ_e) and R_s for photodiode both in dark and under 250 W illumination cases. The exponential growth of the N_ss from midgap toward the bottom of the conductance band is very apparent for two cases. The obtained high value of n and R_s were attributed to the particular distribution of N_ss at metal/PVA interface, surface and fabrication processes, barrier inhomogeneity of interfacial polymer layer and the form of barrier height at M/S interface. While the values of C and G/w increase R_s and R_sh decrease under illumination, due to the illumination induced electron–hole pairs in depletion region. The voltage dependent N_ss profile was also obtained from the dark and illumination capacitance at 1 MHz and these values of N_ss are in good agreement. In addition, the fill factor (FF) under 250 W illumination level was found as 28.5% and this value of FF may be accepted sufficiently high. Thus, the fabricated Au/PVA (Bi-doped)/n-Si structures are more sensitive to light, proposing them as a good candidate as a photodiode or capacitance sensor for optoelectronic applications in modern electronic industry.     

Analysis of interface states and series resistance for Al/PVA:n-CdS nanocomposite metal–semiconductor and metal–insulator–semiconductor diode structures

This paper presents the fabrication and characterization of Al/PVA:n-CdS (MS) and Al/Al₂O₃/PVA:n-CdS (MIS) diode. The effects of interfacial insulator layer, interface states (N _ss ) and series resistance (R _s ) on the electrical characteristics of Al/PVA:n-CdS structures have been investigated using forward and reverse bias I–V, C–V, and G/w–V characteristics at room temperature. Al/PVA:n-CdS diode is fabricated with and without insulator Al₂O₃ layer to explain the effect of insulator layer on main electrical parameters. The values of the ideality factor (n), series resistance (R _s ) and barrier height (? _b ) are calculated from ln(I) vs. V plots, by the Cheung and Norde methods. The energy density distribution profile of the interface states is obtained from the forward bias I–V data by taking into account the bias dependence ideality factor (n(V)) and effective barrier height (? _e ) for MS and MIS diode. The N _ss values increase from mid-gap energy of CdS to the bottom of the conductance band edge for both MS and MIS diode.     

On the energy distribution profile of interface states obtained by taking into account of series resistance in Al/TiO2/p-Si (MIS) structures

The energy distribution profile of the interface states (N_ss) of Al/TiO₂/p-Si (MIS) structures prepared using the sol-gel method was obtained from the forward bias current-voltage (I-V) characteristics by taking into account both the bias dependence of the effective barrier height (?_e) and series resistance (R_s) at room temperature. The main electrical parameters of the MIS structure such as ideality factor (n), zero-bias barrier height (?_b0) and average series resistance values were found to be 1.69, 0.519 eV and 659 Ω, respectively. This high value of n was attributed to the presence of an interfacial insulator layer at the Al/p-Si interface and the density of interface states (N_ss) localized at the Si/TiO₂ interface. The values of N_ss localized at the Si/TiO₂ interface were found with and without the R_s at 0.25-E_v in the range between 8.4×10¹³ and 4.9×10¹³ eV⁻¹ cm⁻². In addition, the frequency dependence of capacitance-voltage (C-V) and conductance-voltage (G/ω-V) characteristics of the structures have been investigated by taking into account the effect of N_ss and R_s at room temperature. It can be found out that the measured C and G/ω are strongly dependent on bias voltage and frequency.     

Analysis of current–voltage and capacitance–voltage characteristics of perylene-monoimide/n-Si Schottky contacts

The electrical and interface state properties of Au/perylene-monoimide (PMI)/n-Si Schottky barrier diode have been investigated by current–voltage (I–V) and capacitance–voltage (C–V) measurements at room temperature. A good rectifying behavior was seen from the I–V characteristics. The series resistance (R_s) values were determined from I–V and C–V characteristics and were found to be 160 Ω and 53 Ω, respectively. The barrier height (Φ_b) of Au/PMI/n-Si Schottky diode was found to be 0.694 eV (I–V) and 0.826 eV (C–V). The ideality factor (n) was obtained to be 4.27 from the forward bias I–V characteristics. The energy distribution of interface state density (N_ss) of the PMI-based structure was determined, and the energy values of N_ss were found in the range from E_c ? 0.508 eV to E_c ? 0.569 eV with the exponential growth from midgap toward the bottom of the conduction band. The values of the N_ss without R_s are 2.11 × 10¹² eV^?1 cm^?2 at E_c ? 0.508 eV and 2.00 × 10¹² eV^?1 cm^?2 at E_c ? 0.569 eV. Based on the above results, it is clear that modification of the interfacial potential barrier for metal/n-Si structures has been achieved using a thin interlayer of the perylene-monomide.     

The influence of annealing temperature and tellurium (Te) on electrical and dielectrical properties of Al/p-CIGSeTe/Mo Schottky diodes

p-CuIn_0.7Ga_0.3(Se_(1?x)Te_x)₂ type thin films were synthesized by thermal evaporation method on Mo coated glass substrates. To obtain Al/CuIn_0.7Ga_0.3(Se_(1?x)Te_x)₂/Mo Schottky diode structure for two compositions of x = 0.0 and 0.6, Al metal was evaporated on upper surface of CuIn_0.7Ga_0.3(Se_(1?x)Te_x)₂ as a front contact. Al/p-CuIn_0.7Ga_0.3(Se_(1?x)Te_x)₂/Mo structures were annealed temperature range from 150 °C to 300 °C for 10 min under vacuum. The electrical and dielectrical properties of Al/p-CuIn_0.7Ga_0.3(Se_(1?x)Te_x)₂ (CIGSeTe) Schottky barrier diodes (SBD) have been investigated. Capacitance–Voltage (C–V) characteristics, Conductance–Voltage (G/w–V) characteristics and interface state density were studied in order to obtain electrical and dielectrical parameters. The effects of interface state density (N_ss), series resistance (R_s), the dielectric constant (?′), dielectric loss (?″), dielectric loss tangent (tan δ), ac electrical conductivity (σ_ac) and carrier doping densities were calculated from the C–V and G/w–V measurements and plotted as a function of annealing temperature. It was observed that the values of carrier doping density N_A for annealing temperature at 150 °C decreased from 2.83 × 10⁺¹⁵ cm^?3 to 2.87 × 10⁺¹⁴ cm^?3 with increasing Te content from x = 0.0 to 0.6. The series resistance for x = 0.0 found to be between 10 and 75 Ω and between 50 and 230 Ω for x = 0.6 in the range of annealing temperature at 150–300 °C.     

Forward and reverse bias current-voltage characteristics of Au/n-Si Schottky barrier diodes with and without SnO2 insulator layer

The effects of interfacial insulator layer, interface states (N_ss) and series resistance (R_s) on the electrical characteristics of Au/n-Si structures have been investigated using forward and reverse bias current-voltage (I-V) characteristics at room temperature. Therefore, Au/n-Si Schottky barrier diodes (SBDs) were fabricated as SBDs with and without insulator SnO₂ layer to explain the effect of insulator layer on main electrical parameters. The values of ideality factor (n), R_s and barrier height (Φ_Bo) were calculated from ln(I) vs. V plots and Cheung methods. The energy density distribution profile of the interface states was obtained from the forward bias I-V data by taking bias dependence of ideality factor, effective barrier height (Φ_e) and R_s into account for MS and MIS SBDs. It was found that N_ss values increase from at about mid-gap energy of Si to bottom of conductance band edge of both SBDs and the MIS SBD’s N_ss values are 5-10 times lower than those of MS SBD’s. An apparent exponential increase from the mid-gap towards the bottom of conductance band is observed for both SBDs’ (MS and MIS) interface states obtained without taking R_s into account.     

Effects of gamma irradiation on electrical parameters of metal–insulator–semiconductor structure with silicon nitride interfacial insulator layer

The effects of gamma irradiation on electrical parameters of Au/Si₃N₄/n-Si (MIS) structure were investigated by using the capacitance–voltage (C–V) and conductance–voltage (G/ω–V) measurements. The MIS structure was irradiated using gamma-radiation source at a dose rate of 0.69?kGy/h. The C–V and G/ω–V measurements were carried out at a total dose range of 0–100?kGy for five different frequencies (1, 10, 100, 500 and 1000?kHz). The obtained results showed that the C and G/ω values decrease with the increasing radiation dose due to the irradiation-induced defects at the interface. Also, the observed decrease in the C and G/ω values with the increasing frequency was explained on the basis of interface states (N_ss). The values of series resistance (R_s) increase with the increasing radiation dose. To obtain the real capacitance and conductance of the capacitor, the measured values of C and G/ω were corrected to eliminate the effect of series resistance. The values of N_ss were determined by using the conductance method and were decreased with the increasing radiation dose.     

The effect of gamma irradiation on electrical and dielectric properties of Al-TiW-Pd2Si/n-Si Schottky diode at room temperature

The effects of ⁶⁰Co (γ-ray) irradiation on the electrical and dielectric properties of Al-TiW-Pd₂Si/n-Si Schottky diodes (SDs) have been investigated by using capacitance-voltage (C-V) and conductance-voltage (G/ω-V) measurements at room temperature and 500 KHz. The corrected capacitance and conductance values were obtained by eliminating the effect of series resistance (R_s) on the measured capacitance (C_m) and conductance (G_m) values. The high-low frequency capacitance (CHF-CLF) method given in [12] as N_ss = (1/qA) [((1/C_LF) − (1/C_ox))⁻¹ −  ((1/C_HF) − (1/C_ox))⁻¹] was successfully adapted to the before-after irradiation capacitance given in this report as N_ss = (1/qA) [((1/C_bef) − (1/C_ox))⁻¹ − ((1/C_after) − (1/C_ox))⁻¹] for the analyzing the density of interface states. The N_ss-V plots give a distinct peak corresponding to localized interface states regions at metal and semiconductor interface. The experimental values of the ac electrical conductivity (σ_ac), the real (M′) and imaginary (M″) parts of the electrical modulus were found to be strong functions of radiation and applied bias voltage, especially in the depletion and accumulation regions. The changes in the dielectric properties in the depletion and accumulation regions stem especially from the restructuring and reordering of the charges at interface states and surface polarization whereas those in the accumulation region are caused by series resistance effect.     

Effects of PEDOT:PSS and crystal violet interface layers on current-voltage performance of Schottky barrier diodes as a function of temperature and variation of diode capacitance with frequency

In this study, diode applications of Crystal Violet (CV) and PEDOT materials were studied. The Ni/p-Si/Al, Ni/CV/p-Si/Al and Ni/PEDOT:PSS/CV/p-Si/Al diodes were fabricated. The I–V (current-voltage) characteristics of all diodes were analyzed at room temperature, it was determined that the PEDOT:PSS and CV materials improved the basic diode parameters. Also, I–V characteristics of Ni/PEDOT:PSS/CV/p-Si/Al of diode were investigated for different temperature values. It has been determined that the basic diode parameters are strongly dependent on temperature. It was determined that while the barrier height (Φ_b) increased with increasing temperature, the ideality factor (n) and the series resistance (R_s) values decreased. Using temperature-dependent measurements, it was determined that the potential barrier and ideality factor values at the contact interface has a double Gaussian distribution. In addition, C–V (capacitance-voltage) measurements of these diodes were analyzed depending on the frequency. It was found that the diode capacitance decreased with increasing frequency.     

Illumination dependence of I-V and C-V characterization of Au/InSb/InP(1 0 0) Schottky structure

The effects of surface preparation and illumination on electric parameters of Au/InSb/InP(100) Schottky diode were investigated, in the later diode InSb forms a fine restructuration layer allowing to block In atoms migration to surface. In order to study the electric characteristics under illumination, we make use of an He-Ne laser of 1 mW power and 632.8 nm wavelength. The current-voltage I(V_G), the capacitance-voltage C(V_G) measurements were plotted and analysed. The saturation current I_s, the serial resistance R_s and the mean ideality factor n are, respectively, equal to 2.03 × 10⁻⁵ A, 85 Ω, 1.7 under dark and to 3.97 × 10⁻⁵ A, 67 Ω, 1.59 under illumination. The analysis of I(V_G) and C(V_G) characteristics allows us to determine the mean interfacial state density N_ss and the transmission coefficient θ_n equal, respectively, to 4.33 × 10¹² eV⁻¹ cm⁻², 4.08 × 10⁻³ under dark and 3.79 × 10¹² eV⁻¹ cm⁻² and 5.65 × 10⁻³ under illumination. The deep discrete donor levels presence in the semiconductor bulk under dark and under illumination are responsible for the non-linearity of the C⁻²(V_G) characteristic.     

The origin of negative capacitance in Au/n-GaAs Schottky barrier diodes (SBDs) prepared by photolithography technique in the wide frequency range

Capacitance–voltage (C–V) and conductance–voltage (G/ω–V) measurements of the Au/n-GaAs Schottky barrier diodes (SBDs) in the wide frequency range of 10 kHz–10 MHz at room temperature were carried out in order to evaluate the reason of negative capacitance (NC). Experimental results show that C and G/ω are strong functions of frequency and bias voltage especially in the accumulation region. NC behavior was observed in the C–V plot for each frequency and the magnitude of absolute value of C increases with decreasing frequency in the forward bias region. Contrary to C, G/ω increases with decreasing frequency positively in this region. NC behavior may be explained by considering the loss of interface charges at occupied states below Fermi level due to impact ionization processes. Such behavior of the C and G/ω values can also be attributed to the increase in the polarization especially at low frequencies and the introduction of more carriers in the structure. The values of R_s decrease exponentially with increasing frequency according to literature. In addition, the values of C and G/ω at 1 MHz were corrected to obtain the real diode capacitance by taking the effect of R_s into account.     

The effect of PVA (Bi2O3-doped) interfacial layer and series resistance on electrical characteristics of Au/n-Si (110) Schottky barrier diodes (SBDs)

Two types of Schottky Barrier Diodes (SBDs) with and without PVA (Bi₂O₃-doped) polymeric interfacial layer, were fabricated and measured at room temperature in order to investigate the effects of the PVA (Bi₂O₃-doped) interfacial layer on the main electrical parameters such as the ideality factor (n), zero-bias barrier height (Φ_B0), series resistance (R_s) and interface-state density (N_ss). Electrical parameters of these two diodes were calculated from the current-voltage (I-V) characteristics and compared with each other. The values of Φ_B0, n and R_s for SBDs without polymeric interfacial layer are 0.71 eV, 1.44 and 4775 Ω, respectively. The values of Φ_B0, n and R_s for SBDs with PVA (Bi₂O₃-doped) polymeric interfacial layer are 0.74 eV, 3.49 and 10,030 Ω, respectively. For two SBDs, the energy density distribution profiles of interface states (N_ss) were obtained from forward-bias I-V measurements by taking the bias dependence of R_s of these devices into account. The values of N_ss obtained for the SBD with PVA (Bi₂O₃-doped) polymeric interfacial layer are smaller than those of the SBD without polymeric interfacial layer.     

Negative capacitance of ZnGa2Se4/Si nano-heterojunction diode

The negative capacitance (NC) behavior in p-ZnGa₂Se₄/n-Si nano-crystalline HJD was characterized by admittance-voltage method. The C–V, G–V and R _s –V for the studied diode were analysed in the frequency range of 1–5 MHz and in the temperature range of 303–423 K. The capacitance and conductance plots were interpreted in terms of interface states and series resistance. The C–V and G/ω–V plots exhibit a pounced peak due to the interface states and the series resistance effects. The negative capacitance behavior in the studied diode can be explained in terms of the transient currents.     

Current conduction mechanism in Al/p-Si Schottky barrier diodes with native insulator layer at low temperatures

The forward bias current-voltage (I-V) characteristics of Al/p-Si (MS) Schottky diodes with native insulator layer were measured in the temperature range of 80-300 K. The obtained zero bias barrier height Φ_B0(I-V), ideality factor (n) and series resistance (R_s) determined by using thermionic emission (TE) mechanism show strong temperature dependence. There is a linear correlation between the Φ_B0(I-V) and n because of the inhomogeneties in the barrier heights (BHs). Calculated values from temperature dependent I-V data reveal an unusual behaviour such that the Φ_B0 decreases, as the n and R_s values are increasing with decreasing absolute temperature, and these changes are more pronounced especially at low temperatures. Such temperature dependence of BH is contradictory with the reported negative temperature coefficient of the barrier height. In order to explain this behaviour we have reported a modification in the expression reverse saturation current I_o including the n and the tunnelling factor (αΧ^1/2δ) estimated to be 15.5. Therefore, corrected effective barrier height Φ_bef.(I-V) versus temperature has a negative temperature coefficients (α = −2.66 × 10⁻⁴ eV/K) and it is in good agreement with negative temperature coefficients (α = −4.73 × 10⁻⁴ eV/K) of Si band gap. In addition, the temperature dependent energy distribution of interface states density N_ss profiles was obtained from the forward bias I-V measurements by taking into account the bias dependence of the Φ_e and n. The forward bias I-V characteristics confirm that the distribution of N_ss, R_s and interfacial insulator layer are important parameters that the current conduction mechanism of MS Schottky diodes.     

Effect of series resistance on the performance of silicon Schottky diode in the presence of tin oxide layer

The current–voltage (I–V) characteristics of Al/SnO₂/p-Si (MIS) Schottky diodes prepared by means of spray deposition method have been measured at 80, 295 and 350 K. In order to interpret the experimentally observed non-ideal Al/SnO₂/p-Si Schottky diode parameters such as, the series resistance R_s, barrier height Φ_B and ideality factor n, a novel calculation method has been reported by taking into account the applied voltage drop across interfacial oxide layer V_i and ideality factor n in the current transport mechanism. The values obtained for V_i were subtracted from the applied voltage values V and then the values of R_s were recalculated. The parameters obtained by accounting for the voltage drop V_i have been compared with those obtained without considering the above voltage drop. It is shown that the values of R_s estimated from Cheung’s method were strongly temperature-dependent and decreased with increasing temperature. It is shown that the voltage drop across the interfacial layer will increase the ideality factor and the voltage dependence of the I–V characteristics. The interface state density N_ss of the diodes has an exponential growth with bias towards the top of the valance band for each temperature; for example, from 2.37 × 10¹³ eV⁻¹ cm⁻² in 0.70−E_v eV to 7.47 × 10¹³ eV⁻¹ cm⁻² in 0.62−E_v eV for 295 K. The mean N_ss estimated from the I–V measurements decreased with increasing the temperature from 8.29 × 10¹³ to 2.20 × 10¹³ eV⁻¹ cm⁻².     

Effects of heavy-ion irradiation on the electrical properties of rf-sputtered HfO2 thin films for advanced CMOS devices

HfO₂-based metal-oxide semiconductor (MOS) capacitors were irradiated with high-energy ion beam to study the irradiation effects in these films. HfO₂ thin films deposited by radio frequency (rf)-sputtering were irradiated with 80 MeV O⁶⁺ ions. The samples were irradiated and characterized at room temperature. Devices were characterized via 1 MHz capacitance–voltage (C?V) measurements using the midgap method. The irradiation induced dispersion in accumulation and depletion regions with increasing fluence is observed. After irradiation, the midgap voltage shift (Δ V _mg) of?0.61 to?1.92 V, flat band voltage shift (Δ V _fb) of?0.48 to?2.88 V and threshold voltage shift (Δ V _th) of?0.966 to?1.96 V were observed. The change in interface trap charge and oxide trap charge densities after 80 MeV O⁶⁺ ions irradiation with fluences were determined from the midgap to flat band stretch out of C?V curves. The results are reported and explained in terms of changes in microstructure and dielectric properties of the HfO₂ thin films after irradiation.