Preparation and characterization of aligned carbon nanotubes/polylactic acid composite fibers

Aligned functionalized multiwalled carbon nanotubes/polylactic acid (MWNTs-PCL/PLA) composite fibers were successfully prepared by electrospinning processing. The MWNTs bonded with the polycaprolactone chains exhibited excellent uniform dispersion in PLA solution by comparing with the acid-functionalized MWNTs and amino-functionalized MWNTs. Optical microscopy was used to study the aligned degree of the fibers and to investigate the influences of the electrodes distance on the alignment and structure of the fibers, and results showed that the best quality of aligned fibers with dense structure and high aligned degree were obtained at an electrodes distance of 3 cm. Moreover, the MWNTs embedded inside the MWNTs-PCL/PLA fibers displayed well orientation along the axes of the fibers, which was demonstrated by field emission scanning electron microscopy, transmission electron microscopy and Raman spectroscopy.     

A comparison between the mechanical and thermal properties of single-walled carbon nanotubes and boron nitride nanotubes

Carbon nanotubes (CNTs) are semimetallic while boron nitride nanotubes (BNNTs) are wide band gap insulators. Despite the discrepancy in their electrical properties, a comparison between the mechanical and thermal properties of CNTs and BNNTs has a significant research value for their potential applications. In this work, molecular dynamics simulations are performed to systematically investigate the mechanical and thermal properties of CNTs and BNNTs. The calculated Young’s modulus is about 1.1 TPa for CNTs and 0.72 TPa for BNNTs under axial compressions. The critical bucking strain and maximum stress are inversely proportional to both diameter and length-diameter ratio and CNTs are identified axially stiffer than BNNTs. Thermal conductivities of (10, 0) CNTs and (10, 0) BNNTs follow similar trends with respect to length and temperature and are lower than that of their two-dimensional counterparts, graphene nanoribbons (GNRs) and BN nanoribbons (BNNRs), respectively. As the temperature falls below 200 K (130 K) the thermal conductivity of BNNTs (BNNRs) is larger than that of CNTs (GNRs), while at higher temperature it is lower than the latter. In addition, thermal conductivities of a (10, 0) CNT and a (10, 0) BNNT are further studied and analyzed under various axial compressive strains. Low-frequency phonons which mainly come from flexure modes are believed to make dominant contribution to the thermal conductivity of CNTs and BNNTs.     

Influence of filler alignment in the mechanical and electrical properties of carbon nanotubes/epoxy nanocomposites

In this work, we report the mechanical and electrical properties of carbon nanotubes/epoxy composites prepared with aligned and randomly oriented nanotubes as filler. The samples are disks of 30 mm in diameter and 3 mm in thickness. To obtain the carbon nanotubes alignment, an external electric field (250 VAC; 50 Hz) was applied through the thickness of the sample during all the cure process. The AC electrical current was measured, during the cure, as a strategy to determine the optimum time in which the alignment reaches the maximum value. DC conductivity measured after the cure shows a percolation threshold in the filler content one order of magnitude smaller for composites with aligned nanotubes than for composites with randomly oriented filler (from 0.06 to 0.5 wt%). In the percolation threshold, the achieved conductivity was 1.4×10⁻⁵ Sm⁻¹. In both cases, aligned and randomly distributed carbon nanotube composites, the wear resistance increases with the addition of the filler while the Rockwell hardness decreases independently of the nanotubes alignment.     

Mechanical properties of nickel-coated single-walled carbon nanotubes and their embedded gold matrix composites

The effects of nickel coating on the mechanical behaviors of armchair single-walled carbon nanotubes (SWCNTs) and their embedded gold matrix composites under axial tension are investigated using molecular dynamics (MD) simulation method. The results show that the Young's moduli and tensile strength of SWCNTs obviously decrease after nickel coating. For armchair SWCNTs, the decreased ratio of the Young's moduli of SWCNTs with smaller radius is larger than that of SWCNTs with larger radius. A comparison is made between the response to Young's modulus of a composite with parallel embedded nanotube and the response of a composite with vertically embedded nanotube. The results show that the uncoated SWCNT can enhance the Young's modulus of composite under the condition of parallel embedment, but such improvement disappears under the condition of vertical embedment because the interaction between SWCNT and gold matrix is too weak for effective load transfer. However, the nickel-coated SWCNT can indeed significantly improve the composite behavior.     

Study the effect of acetic acid on structural,optical and mechanical properties of PVA/chitosan/MWCNT films

Polyvinyl alcohol (PVA)/chitosan/multiwalled carbon nanotube (MWCNT) films were successfully prepared by using solution-casting method. Structural properties were studied using Fourier transform infrared (FTIR) and X-ray diffraction (XRD) spectroscopies. The effect of acetic acid (AA) concentration on the films optical parameters was studied by using absorbance and transmittance data recorded during ultraviolet-visible (UV–Vis) spectroscopy. The results indicated that increasing the AA concentration in MWCNT-reinforced PVA films caused an increase in their optical capability. We also evaluated mechanical properties such as stress-strain behavior, Young's modulus, tensile strength, elongation at break, etc. Mechanical indices have been modified by introducing carbon nanotubes, even though enhancing the AA concentration meets significant restrictions on higher percentages of AA concentration, which needs to be delicately considered. The porous structure of the films, such as porous pattern, materials’ diameter, and shape was examined by field emission electron microscopy (FESEM). Engineering analyses showed that the films reinforced with MWCNTs exhibited an interconnected homogenous structure in various acid concentrations.     

Effects of enhanced hydrogen bonding on the mechanical properties of poly (vinyl alcohol)/carbon nanotubes nanocomposites

In this study, poly (vinyl alcohol) (PVA) composites reinforced by multiwall carbon nanotubes (MWCNTs) functionalized with either phenolic hydroxyl groups (MWCNTs-f-OH) or PVP molecule (PVP@MWCNTs) were fabricated. The objective was to elucidate the effect of different MWCNTs surface functionalization on the mechanical properties of the nanocomposites. It was found that both of PVP@MWCNTs and MWCNTs-f-OH had a good dispersion in PVA matrix. However, the MWCNTs-f-OH had stronger effective interfacial interaction with PVA matrix than PVP@MWCNTs, owe to the formation of hydrogen bonds between MWCNTs-f-OH and PVA. The stress-strain measurements showed that the Young’s modulus and tensile strength of MWCNTs-f-OH/PVA with only 1.0 wt.% contents increased by 200 and 100% compare with that of PVA, respectively. The findings of this experimental study emphasized the critical role of MWCNTs surface morphology in determining the mechanical properties of nanocomposites, and shed new light on understanding and advancing the properties of carbon nanotube based composites.     

Optimizing mechanical and thermal expansion properties of carbon/carbon composites by controlling textures

The present study explored the effect of medium texture (MT) content on flexural properties and thermal expansion coefficients (CTE_S) of carbon/carbon (C/C) composites with multilayered pyrolytic carbon. The specimen with 39% MT exhibited maximum flexural strength of 221.55 MPa, increasing by 52% compared with pure high texture. While the flexural strength decreased when the MT content exceeded 39%. The excellent strength can be attributed to crack deflection between multilayered texture and the strong interface bonding between fibers and matrix. Moreover, the four specimens expressed a similar trend of CTE_S in the direction of XY and Z. In the direction of XY, the specimen with 39% MT had the lowest CTE_S from 800 °C to 2100 °C. Therefore, the C/C composites with 39% MT have the best mechanical and thermal expansion properties, which means that the properties of C/C composites can be optimized by controlling the texture.     

Morphology, mechanical, cross-linking, thermal, and tribological properties of nitrile and hydrogenated nitrile rubber/multi-walled carbon nanotubes composites prepared by melt compounding: The effect of acrylonitrile content and hydrogenation

The purpose of this work was to prepare nanocomposites by mixing multi-walled carbon nanotubes (MWCNT) with nitrile and hydrogenated nitrile elastomers (NBR and HNBR). Utilization of transmission electronic microscopy (TEM), scanning electron microscopy (SEM), and small- and wide-angle X-ray scattering techniques (SAXS and WAXS) for advanced morphology observation of conducting filler-reinforced nitrile and hydrogenated nitrile rubber composites is reported. Principal results were increases in hardness (maximally 97 Shore, type A), elastic modulus (maximally 981 MPa), tensile strength (maximally 27.7 MPa), elongation at break (maximally 216%), cross-link density (maximally 7.94 × 10²⁸ m⁻³), density (maximally 1.16 g cm⁻³), and tear strength (11.2 kN m⁻¹), which were clearly visible at particular acrylonitrile contents both for unhydrogenated and hydrogenated polymers due to enhanced distribution of carbon nanotubes (CNT) and their aggregated particles in the applied rubber matrix. Conclusion was that multi-walled carbon nanotubes improved the performance of nitrile and hydrogenated nitrile rubber nanocomposites prepared by melt compounding.     

Rheological,thermal, and mechanical properties of poly(ethylene naphthalate)/poly(ethylene terephthalate) blends

Structural, Theological, thermal, and mechanical properties of blends of poly(ethylene naphthalate) (PEN) and poly(ethylene terephthalate) (PET) obtained by melt blending were investigated using capillary rheometry, differential scanning calorimetry (DSC), scanning electron microscopic (SEM) observation, tensile testing. X-ray diffraction, and ¹H nuclear magnetic resonance (NMR) measurements. The melt Theological behavior of the PEN/PET blends was very similar to that of the two parent polymers. The melt viscosity of the blends was between that of PEN and that of PET. Thermal properties and NMR measurement of the blends revealed that PEN is partially miscible with PET in the as molded blends, indicating that an interchange reaction occurs to some extent on melt processing. The blend of 50/50 PEN/PET was more difficult to crystallize compared with blends of other PEN/PET ratios. The blends, once melted during DSC measurements, almost never showed cold crystallization and subsequent melting and definitely exhibited a single glass transition temperature between those of PEN and PET during a reheating run. Improvement of the miscibility between PEN and PET with melting is mostly due to an increase in transesterification. The tensile modulus of the PEN/PET blend strands had a low value, reflecting amorphous structures of the blends, while tensile strength at the yield point increased linearly with increasing PEN content.     

Thermal and electrical conductivity of poly(l-lactide)/multiwalled carbon nanotube nanocomposites

Multiwalled carbon nanotubes (MWCNTs) are considered to be the ideal reinforcing agent for high-strength polymer composites, because of their fantastic mechanical strength, high electrical and thermal conductivity and high aspect ratio. Polymer/MWCNTs composites are easily molded, and the resulting shaped plastic articles have a perfect surface appearance compared with polymer composites made using usual carbon or glass fibers. Good interfacial adhesion between the MWCNTs and the polymer matrix is essential for efficient load transfer in the composite. The ultrahigh strength polymer composites demand the uniform dispersion of the MWCNTs in the polymer matrix without their aggregation and the good miscibility between MWCNT and polymer matrix. This approach can also be applied to biodegradable synthetic aliphatic polyesters such as poly(l-lactide) (PLLA), which has received a great deal of attention due to environmental concerns. In this study, PLLA was melt-compounded with MWCNTs. A high degree of dispersion of the MWCNTs in the composites was obtained by grafting PLLA onto the MWCNTs (PLLA-g-MWCNTs). After oxidizing the MWCNTs by treating them with strong acids, they were reacted with l-lactide to produce the PLLA-g-MWCNTs. The mechanical properties of the PLLA/PLLA-g-MWCNT composite were higher than those of the PLLA/MWCNT composite. The electrical conductivity of the composites was determined by measuring the volume resistivity, which is a value of the resistance expressed in a unit volume by two-probe method. The thermal diffusivity and heat capacity of composites was measured by laser flash method, and the effects of modification of the MWCNT in PLLA matrix are discussed.     

The physical,mechanical, thermal and barrier properties of starch nanoparticle (SNP)/polyurethane (PU) nanocomposite films synthesised by an ultrasound-assisted process

This article reports on the ultrasound-assisted acid hydrolysis for the synthesis and evaluation of starch nanoparticles (SNP) as nanofillers to improve the physical, mechanical, thermal, and barrier properties of polyurethane (PU) films. During the ultrasonic irradiation, dropwise addition of 0.25 mol L^-1 H₂SO₄ was carried out to the starch dispersion for the preparation of SNPs. The synthesized SNPs were blended uniformly within the PU matrix using ultrasonic irradiation (20 kHz, 220 W pulse mode). The temperature was kept constant during the synthesis (4 °C). The nanocomposite coating films were made with a regulated thickness using the casting method. The effect of SNP content (wt%) in nanocomposite coating films on various properties such as morphology, water vapour permeability (WVP), glass transition temperature (Tg), microbial barrier, and mechanical properties was studied. The addition of SNP to the PU matrix increased the roughness of the surface, and Tg by 7 °C, lowering WVP by 60% compared to the PU film without the addition of SNP. As the SNP concentration was increased, the opacity of the film increased. The reinforcement of the SNP in the PU matrix enhanced the microbial barrier of the film by 99.9%, with the optimal content of SNP being 5%. Improvement in the toughness and barrier properties was observed with an increase in the SNP content of the film.     

Preparation, magnetic and electromagnetic properties of polyaniline/strontium ferrite/multiwalled carbon nanotubes composite

Strontium ferrite particles were firstly prepared by sol-gel method and self-propagating synthesis, and then the polyaniline/strontium ferrite/multiwalled carbon nanotubes composites were synthesized through in situ polymerization approach. Structure, morphology and properties of the composite were characterized by various instruments. XRD analysis shows that the output of PANI increases with the increase of the content of MWCNTs, due to the large surface area of MWCNTs. Because of the coating of PANI, the outer diameter of MWCNTs increases from 10 nm to 20-40 nm. The electrical conductivity of the composites increases with the amount increase of MWCNTs and reaches 7.2196 S/cm in the presence of 2 g MWCNTs. The coercive force of the composites prepared with 2 g MWCNTs is 7457.17 Oe, which is much bigger than that of SrFe₁₂O₁₉ particles 6145.6 Oe, however, both the saturation magnetization and the remanent magnetization of the composite become much smaller than those of SrFe₁₂O₁₉ particles. The electromagnetic properties of the composite are excellent in the frequency range of 2-18 GHz, which mainly depend on the dielectric loss in the range of 2-9 GHz, and mainly on the magnetic loss in the range of 9-18 GHz.     

Carbon nanotubes/magnetite hybrids prepared by a facile synthesis process and their magnetic properties

In this paper, a facile synthesis process is proposed to prepare multiwalled carbon nanotubes/magnetite (MWCNTs/Fe₃O₄) hybrids. The process involves two steps: (1) water-soluble CNTs are synthesized by one-pot modification using potassium persulfate (KPS) as oxidant. (2) Fe₃O₄ is assembled along the treated CNTs by employing a facile hydrothermal process with the presence of hydrazine hydrate as the mineralizer. The treated CNTs can be easily dispersed in aqueous solvent. Moreover, X-ray photoelectron spectroscopy (XPS) analysis reveals that several functional groups such as potassium carboxylate (-COOK), carbonyl (-CO) and hydroxyl (-C-OH) groups are formed on the nanotube surfaces. The MWCNTs/Fe₃O₄ hybrids are characterized with respect to crystal structure, morphology, element composition and magnetic property by X-ray diffraction (XRD), transmission electron microscopy (TEM), XPS and superconducting quantum interference device (SQUID) magnetometer. XRD and TEM results show that the Fe₃O₄ nanoparticles with diameter in the range of 20-60 nm were firmly assembled on the nanotube surface. The magnetic property investigation indicated that the CNTs/Fe₃O₄ hybrids exhibit a ferromagnetic behavior and possess a saturation magnetization of 32.2 emu/g. Further investigation indicates that the size of assembled Fe₃O₄ nanoparticles can be turned by varying experiment factors. Moreover, a probable growth mechanism for the preparation of CNTs/Fe₃O₄ hybrids was discussed.     

Poly(butylene terephthalate)/phenoxy blends: Synergistic behavior in mechanical properties

The mechanical properties of miscible poly(butylene terephthalate) (PBT)/poly (hydroxy ether of bisphenol A) (phenoxy) blends obtained by melt mixing have been studied by means of the tensile test. The crystallinity of the blends has been studied by means of DSC and density measurements. A synergistic behavior, principally in the break properties, at high PBT contents in the blends is observed. As can be seen from the torque and density data, this synergistic behavior is related with the high level of miscibility which seems to exist at high PBT contents compared with that of the high phenoxy content region.     

Preparation and characterization of poly(vinyl alcohol)/graphene nanofibers synthesized by electrospinning

We report on the synthesis and characterization of electrospun polyvinyl alcohol (PVA)/graphene nanofibers. The samples produced were characterized by Raman spectroscopy for structural and defect density analysis, scanning electron microscopy (SEM) for morphological analysis, and thermogravimetric (TGA) for thermal analysis. SEM measurements show uniform hollow PVA fibers formation and excellent graphene dispersion within the fibers, while TGA measurements show the improved thermal stability of PVA in the presence of graphene. The synthesized polymer reinforced nanofibers have potential to serve in many different applications such as thermal management, supercapacitor electrodes and biomedical materials for drug delivery.     

Effect of clay silylation on curing and mechanical and thermal properties of unsaturated polyester/montmorillonite nanocomposites

This work focuses on the chemical modification of montmorillonite (MMT) (Cloisite® Na) with compatible silanes, vinyltriethoxysilane (CVTES) and γ-methacryloxypropyltrimethoxysilane (CMPS) in order to prevent agglomeration and to improve montmorillonite interaction with an unsaturated polyester resin matrix seeking to achieve a multifunctional composite. Clays were dispersed in the resin by mechanical stirring and sonication and the nanocomposites were prepared by resin transfer into a mold. The mechanical, morphological, thermal and flammability properties of the obtained composites were compared with those prepared using commercial Cloisite® 30B (C30B) and Cloisite® 15A (C15A) clays. Advantages of using silane-modified clays (CVTES and CMPS) as compared with organic-modified clays (C30B and C15A) can be summarized as similar flexural strength and linear burning rate but higher storage modulus and improved adhesion to the polyester resin with consequent higher thermal deflection temperature and reinforcement effectiveness at higher temperatures. However, organic modified clays showed better dispersion (tendency to exfoliate) and consequently delayed thermal volatilization due to the clay barrier effect.     

Optical,thermal and mechanical characterization of Al(III)/Sb(III)-doped tris(thiourea)zinc(II) sulphate crystals

The influence of Al(III)/Sb(III)-doping on the properties of tris(thiourea)zinc(II) sulphate (ZTS) crystals grown by slow evaporation solution growth technique is reported. The as-grown crystals belong to orthorhombic system and cell parameters are, a = 7.77 Å, b = 11.13 Å, c = 15.47 Å, V = 1338 Å³ (Al(III)-doped) and a = 11.1996 Å, b = 7.770 Å, c = 15.5598 Å, V = 1368.3 Å³ (Sb(III)-doped). The structure and the crystallinity of the materials are further confirmed by powder X-ray diffraction analysis. The modes of vibrations of different functional groups present are identified by Fourier transform infrared studies. Thermogravimetric/differential thermal analysis studies reveal the purity of the materials and no decomposition is observed up to the melting point. Surface morphological changes due to doping are observed by scanning electron microscopy. Microhardness study was carried out to elucidate the mechanistic behavior microhardness studies were carried out to elucidate the mechanistic behavior. Second harmonic generation activity is much better in the case of Sb(III)-doping. The specimen is also characterized by dielectric studies.     

Improvement in mechanical and optical properties of vapour chopped vacuum evaporated PANI/PMMA composite thin film

PANI/PMMA composite was synthesized by emulsion polymerization pathway and the composite thin film was obtained by vacuum evaporation. The effect of vapour chopping and varying PMMA concentration was also studied. The FTIR spectra showed that the PANI/PMMA composite thin film deposited as a short chain oligomers. Increase in transmittance and decrease in refractive index was obtained with increasing concentration of PMMA, which further increased the adhesion and decreased intrinsic stress. The vapour chopping improved its optical as well as mechanical properties and produced smoother surface morphology. Increase of PMMA made the film more amorphous and does not change its band gap.     

Effect of intercalation on electrical and mechanical properties of C/C composites

The work is concerned with modification of C/C composites by intercalation of copper chloride. The samples of composites were made from graphite fibres and carbon matrix derived from mesophase pitch and from phenol-formaldehyde resin. The samples were prepared by impregnating graphite fibres with a liquid pitch or polymer solution to obtain unidirectional laminates. The laminates were used to prepare the composites which were then subjected to carbonization and graphitization up to 2150 °C. The work discusses the problem relevant to the effect of intercalation on mechanical and electrical properties of composites. The studies indicated that both mesophase pitch-based composites and phenolic-derived carbon-carbon composites changed their electrical and mechanical properties upon intercalation with copper chloride. Electrical conductivity of both types of composites decreased as a result of the damages formed during intercalation.     

Influence of silicon on the microstructure and mechanical properties of Zr-Si-N composite films

A series of Zr-Si-N composite films with different Si contents were synthesized in an Ar and N₂ mixture atmosphere by the bi-target reactive magnetron sputtering method. These films’ composition, microstructure and mechanical properties were characterized by energy dispersive spectroscopy, X-ray diffraction, scanning electron microscopy, atomic force microscopy and nanoindentation. Experimental results revealed that after the addition of silicon, Si₃N₄ interfacial phase formed on the surface of ZrN grains and prevented them from growing up. Zr-Si-N composite films were strengthened at low Si content with the hardness and elastic modulus reaching their maximum values of 29.8 and 352 GPa at 6.2 at% Si, respectively. With a further increase of Si content, the crystalline Zr-Si-N films gradually transformed into amorphous, accompanied with a remarkable fall of films’ mechanical properties. This limited enhancement of mechanical properties in the Zr-Si-N films may be due to the low wettability of Si₃N₄ on the surface of ZrN grains.