Preparation of magnesium ferrite nanoparticles by ultrasonic wave-assisted aqueous solution ball milling

Magnesium ferrite, MgFe₂O₄ nanoparticles with high saturation magnetization were successfully synthesized using ultrasonic wave-assisted ball milling. In this study, the raw materials were 4MgCO₃·Mg(OH)₂·5H₂O and Fe₂O₃ powders and the grinding media was stainless steel ball. The average particle diameter of the product MgFe₂O₄ powders was 20 nm and the saturation magnetization of them reached 54.8 emu/g. The different results of aqueous solution ball milling with and without ultrasonic wave revealed that it was the coupling effect of ultrasonic wave and mechanical force that played an important role during the synthesis of MgFe₂O₄. In addition, the effect of the frequency of the ultrasonic wave on the ball milling process was investigated.     

Characterizing the coating and size-resolved oxidative stability of carbon-coated aluminum nanoparticles by single-particle mass-spectrometry

Aluminum nanoparticles are of significant interest in enhancing the rate of energy release from propellants. One of the major impediments to their use is that bare aluminum is highly reactive, while oxide coated aluminum significantly decreases overall performance. We investigate creating aluminum nanoparticles with a thin carbon coating using either a laser induced plasma or a DC plasma-arc. The carbon coating was created by injecting ethylene (C₂H₄) directly downstream of the plasma. The elemental composition of the coated aluminum nanoparticles was measured in real time with a recently developed quantitative single particle mass spectrometer (SPMS). We found that the aluminum nanoparticles were coated with a carbon layer of thickness around 1–3 nm.The thermal and oxidative stability of these particles was determined by passing the aerosols through a heated flow reactor in a carrier flow of either air or argon, and measuring the aluminum, carbon and oxygen content in the particles with the single particle mass spectrometer. We found that below 700°C the coating was stable, but that the coating oxidized above ∼ ∼800°C. In contrast the carbon coating was thermally stable above ∼ ∼900°C. These results indicate that a carbon coating may be a suitable passivating agent.     

Formation of ZnO@Cd(OH)2 core-shell nanoparticles by sol-gel method: An approach to modify surface chemistry for stable and enhanced green emission

We report the formation of highly stable and luminescent ZnO@Cd(OH)₂ core-shell nanoparticles by simple introduction of cadmium salt in the initial precursor solution, used to synthesize ZnO nanoparticles by sol-gel route. The cadmium to zinc salt concentration ratio has been also varied to control the growth of ZnO nanoparticles at the smaller particle size. Formation of ZnO@Cd(OH)₂ core-shell nanostructure has been confirmed by X-ray diffraction (XRD), energy dispersive analysis of X-rays (EDAX) and X-ray photoelectron spectroscopy (XPS). UV-vis absorption spectroscopy exhibits blue-shift in absorption edge on increasing cadmium concentrations. The photoluminescence emission spectra showed the remarkably stable and enhanced visible (green) emission from suspended ZnO@Cd(OH)₂ nanoparticles in comparison to bare ZnO nanoparticles. It is postulated that Cd(OH)₂ layer at the surface of ZnO nanoparticles prevents the agglomeration of nanoparticles and efficiently assists the trapping of hole at the surface site, a first step necessary for visible emission. The Fourier transform infrared spectroscopy (FTIR) also supports our assumption about surface chemistry.     

Surface functionalization, morphology and thermal properties of polyamide6/O-MMT composite nanofibers by Fe2O3 sputter coating

In the present work, the pure polyamide6 (PA6) nanofiber and PA6/organically modified montmorillonite (O-MMT) composite nanofiber were firstly prepared by a facile compounding process with electrospinning, and then coated by nanosize Fe₂O₃ using magnetron sputter technique. The effects of Fe₂O₃ sputter coating on structures, surface morphology and thermal stability were characterized by scanning electron microscope (SEM), X-ray photoelectron spectroscopy (XPS), energy dispersive X-ray spectroscopy (EDX), atomic force microscope (AFM) and thermogravimetric analyses (TGA), respectively. The SEM images showed that the diameters of composite nanofiber were decreased with the loadings of O-MMT and the nanosize Fe₂O₃ is well coated on the surface of the homogeneous and cylindrical nanofibers. The XPS spectra reflected the chemical features of the deposited nanostructures. The EDX confirmed the presence of the O-MMT and Fe₂O₃ in the fibers. The AFM observation revealed that there was a remarkable difference in the surface morphology of composite nanofiber before and after sputter coating. The TGA analysis indicated the barrier effects of silicate clay layers and catalysis effects of Fe₂O₃ improved thermal stability properties of the composite nanofiber.     

Structural, optical, and electronic properties of colloidal CuO nanoparticles formed by using a colloid-thermal synthesis process

Colloidal cupric oxide (CuO) nanoparticles were formed by using a colloid-thermal synthesis process. X-ray diffraction patterns, transmission electron microscopy (TEM) images, high-resolution TEM images, and X-ray energy dispersive spectrometry profiles showed that the colloidal CuO nanoparticles were formed. The optical band-gap energy of CuO nanoparticles at 300 K, as determined from the absorbance spectrum, was 3.63 eV. A photoluminescence spectrum at 300 K showed that a dominant emission peak appeared at the blue region. X-ray photoelectron spectroscopy profiles showed that the O 1s and the Cu 2p peaks corresponding to the CuO nanoparticles were observed.     

p‐toluenesulfonic acid‐catalyzed synthesis of polysubstituted quinolines via Friedländer reaction under ball‐milling conditions at room temperature and theoretical study on the mechanism using a density functional theory method

The synthesis of polysubstituted quinolines was accomplished through Friedländer annulation between 2‐aminoaryl ketones and different active methylene compounds at room temperature using ball‐milling technique in the presence of p‐toluenesulfonic acid. The mechanism of the reaction investigated by density functional theory‐based modeling is also reported. This study aims at giving insight into the mechanism of the Friedländer reaction in the presence of acid catalysts. Copyright © 2014 John Wiley & Sons, Ltd.     

Synthesis and characterization of ZnS:Cu,Al phosphor prepared by a chemical solution method

A novel and simple synthesis route for the production of ZnS:Cu,Al sub-micron phosphor powder is reported. Both the host and activator cations were co-precipitated from an ethanol medium by mixing with a diluted ammonium sulfide solution. The co-precipitated ZnS:Cu,Al was in cubic zinc blende structure after an intermediate-temperature furnace annealing. Strong photoluminescent and cathodoluminescent (CL) emission were observed, which was attributed to the 3d¹⁰-3d⁹4s¹ radiative transition at those copper sites. At an accelerating voltage of 1 kV, the CL intensity of the co-precipitated ZnS:Cu,Al sample was recorded 94% of the commercial reference phosphor with the same composition made by high temperature solid-state-reaction method. The particle size of the co-precipitated phosphor powders was found to be controllable simply through adjusting the reactant concentrations. The particle size of the annealed samples was measured by dynamic light scattering, which showed a mean particle diameter between 200 and 700 nm depending on the co-precipitation conditions.     

A versatile method for the preparation of end-functional polymers onto SiO2 nanoparticles by a combination of surface-initiated ATRP and Huisgen [3 + 2] cycloaddition

A versatile method was developed for the chain-end functionalization of the grafted polymer chains for surface modification of nanoparticles with functionalized groups through a combination of surface-initiated atom-transfer radical polymerization (ATRP) and Huisgen [3 + 2] cycloaddition. First, the surface of SiO₂ nanoparticles was modified with poly(methyl methacrylate) (PMMA) brushes via the “grafting from” approach. The terminal bromides of PMMA-grafted SiO₂ nanoparticles were then transformed into an azide function by nucleophilic substitution. These azido-terminated PMMA brushes on the nanoparticle surface were reacted with alkyne-terminated functional end group via Huisgen [3 + 2] cycloaddition. FTIR and ¹H NMR spectra indicated quantitative transformation of the chain ends of PMMA brushes onto SiO₂ nanoparticles into the desired functional group. And, the dispersibility of the end-functional polymer-grafted SiO₂ nanoparticles was investigated with a transmission electron microscope (TEM).