Selective Solid-Phase Extraction of Trace Copper Ions in Aqueous Solution with a Cu(II)-Imprinted Interpenetrating Polymer Network Gel Prepared by Ionic Imprinted Polymer (IIP) Technique

An Cu(II)-imprinted interpenetrating polymer network (IPN) gel of epoxy-diethylenetriamine and methacrylic acid-acrylamide-N,N′-methylene-bis-(acrylamide) was synthesized by the ionic imprint polymer (IIP) technique. The first polymer network is formed by epoxy gelation with diethylenetriamine. The other is formed by copper methacrylate co- polymerization with acrylamide and cross-linker N,N′-methylene-bis-(acrylamide). The adsorption–desorption characteristics of the IPN gel as a highly selective solid-phase extraction (SPE) and preconcentration adsorbent for Cu²⁺ from aqueous solution were investigated. The experimental results show that trace Cu²⁺ ions can be quantitatively enriched at pH 5 with recovery >95%. The maximum static adsorption capacity of the ion-imprinted functionalized gel adsorbent was 76 mg g⁻¹. Comparing with non-imprinted IPN gel, the imprinted IPN gel has higher adsorption capacity and selectivity for Cu²⁺ by the static adsorption–desorption experiment. Simultaneously, the times of adsorption equilibration and complete desorption were remarkably short. The precision (RSD) for 11 replicate adsorbent extractions of 20 ng mL⁻¹ Cu²⁺ was 3.4%. The established procedure was applied to two real water samples with satisfactory results. The prepared ion-imprinted IPN gel adsorbent was shown to be promising for solid-phase extraction coupled with atomic absorption spectrometry (AAS) for the determination of trace copper in real samples. In addition, the coordination interaction of Cu²⁺ and functional groups of the IPN gel adsorbent was primarily discussed by FT-IR spectra.     

Up-conversion yield in glass ceramics containing silver

Small silver particles are known to increase the fluorescence yield in rare-earth-doped glasses. These particles can be grown easily in glass ceramics of general composition (PbF₂, GeO₂, YbF₃, ErF₃). We have studied the effect of the addition of silver on the up-conversion yield due to sequential energy transfer between Yb³⁺ and Er³⁺ ions. The origin and the information that can be obtained from this effect are discussed.     

Thermal polymerization of acrylamide by differential scanning calorimetry

Thermal polymerization of acrylamide was studied by differential scanning calorimetry. Latent heat of fusion ΔH_f and enthalpy of polymerization ΔH_p values were found to be 36 and ?18.0 kcal mol^?1, respectively. The overall activation energy E for the polymerization was calculated to be 19 k cal mol^?1 up to 60% conversion. The added free-radical inhibitor (benzoquinone) was found to desensitize the thermal polymerization of acrylamide suggesting the polymerization to be a free-radical type. The existing rate equation for the heterogeneous bulk polymerization in the presence of initiators has been modified for the thermally initiated bulk polymerization of acrylamide. The experimental overall E value was found to agree well with the calculated E value when considering only the propagation and termination steps, thereby suggesting the process to be similar to postpolymerization of acrylamide.     

Synthesis and structural studies of hydrazino-crown ethers and thermodynamic studies of their interaction with transition,and post-transition metal ions and methyl ammonium ion

Hydrazino-crown ethers have been synthesized in only 3 or 4 steps starting from 1,2-diacetylhydrazine. The X-ray crystal structure of protonated hydrazino-19-crown-7 (2) showed that one of the hydrazino nitrogen atoms was directed outside the ring cavity. A solvent methanol molecule is held in the cavity of the host ligand by three hydrogen bonds involving two hydrogen atoms bonded to nitrogens of the ligand and the alcohol hydrogen of the methanol. The logK values for the interaction of2 with CH₃NH ₊ ³ , Ag⁺, Pb²⁺, and Cd²⁺ were much less than those for the interaction of symmetrical triaza-l8-crown-6 (5) with the same cations. Hydrazino-crown2 reduced silver ions to silver metal when a solution of2 and silver ions in DMSO was allowed to stand for several days.     

Sensitive and Selective Fluorescent and Colorimetric Sensor for Ag+ Based on the Supramolecular Self‐Assembly in Semi‐Water

Specific recognition of ultratrace levels of ions in semi‐water using super‐quicker methods is still a challenge for environmental monitoring. Herein we report a fluorescent and colormetric sensor ( ZH ) based on supramolecular self‐assembly, whose structure was destroyed by the addition of ultratrace of silver ions. The process promoted either naked eye visible color changes or fluorescence intensity quenched in conjunction with a wide pH range. Systematic studies revealed very high selectivity (0.07 µmol/L) for silver ions, and other common cations, e.g ., Hg²⁺, Cu²⁺, Cd²⁺, Pb²⁺ had nearly no influence on the sensing behavior. This sensor also served as a multiple use of component in sensing materials by addition of I⁻ into the mixture of ZH and Ag⁺ (about 5 times). What's more, ZH containing filter paper emerged distinct color and fluorescence changes upon exposure to silver (Ag⁺), which could be used as a portable method to undertake field testing for Ag ⁺ .     

Chemical properties of N-2-Sulfoethylchitosan with a medium degree of substitution

A method was developed for the preparation of N-2-sulfoethylchitosan (SECH) via synthesis in a gel with the use of the reaction of chitosan and sodium 2-bromoethanesulfonate. This method makes it possible to conduct a polymer-like transformation without any acid or base. The structures of the obtained polymers were confirmed via IR and ¹H NMR spectroscopy. The study of the sorption of Ag⁺, Cu²⁺, Zn²⁺, Ni²⁺, Co²⁺, Cd²⁺, Pb²⁺, Mn²⁺, Mg²⁺, Ca²⁺, Sr²⁺, and Ba²⁺ ions that were crosslinked by SECH during their joint presence in an ammonia-acetate buffer solution showed high values of selectivity in relation to those of silver(I) and copper(II). The selectivity of the sorption of silver(I) ions with respect to copper(II) ions increased with an increase in the degree of substitution of SECH.     

Mechanism of silver nucleation upon the radiation-induced reduction of its ions in polyphosphate-containing aqueous solutions

Long-lived (hours to days) silver clusters, Ag ₄ ²⁺ , Ag ₄ ⁺ , Ag ₈ ²⁺ , etc., are formed upon the radiation-induced reduction of Ag⁺ ions in aqueous solutions containing sodium polyphosphate. The efficiency of the cluster formation decreases and the stability of the clusters increase with a rise in the concentration of the polymeric stabilizer. In the course of the aggregation of clusters, their sizes increase, quasi-metallic particles emerge, and the process terminates with the formation of silver nanoparticles. The mechanism of silver nucleation upon the radiation-induced reduction of silver ions in aqueous solutions is discussed.     

Kinetics of polymerization initiated by Mn3+–substrate redox system. I

The kinetics and mechanism of polymerization of acrylamide (AM) initiated by manganese (III) acetate (MTA)–diglycolic acid (DGA) redox system in aqueous sulfuric acid were studied in the temperature range 20-35°C. The overall rates of polymerization and the disappearance of Mn³⁺ and the kinetic chain lengths of polyacrylamide were determined. The polymerization reaction is initiated by the organic free radical arising from the Mn³⁺–diglycolic acid reaction and the termination is by the metal ions. The rate of polymerization of acrylamide was found to be proportional to the first power of monomer and diglycolic acid and independent of manganese(III) acetate. The various rate parameters were evaluated.     

Ion-imprinted interpenetrating network gels for solid-phase extraction of heavy metal ions

In the present work, ion-imprinted interpenetrating polymer network (IPN) gels were prepared by free radical/cationic hybrid polymerisation of acrylamide (AAm) and 1,4-butanediol vinyl ether (BVE). These gels were respectively used for separation of Cu²⁺, Ni²⁺ and Zn²⁺ ions in natural water samples. Experimental conditions for effective adsorption of metal ions were optimised with respect to different experimental parameters by column procedures in detail. The optimum pH value for the adsorption of Cu²⁺, Ni²⁺ and Zn²⁺ ions on these sorbents was 6.0. Complete elution of the adsorbed metal ions from the sorbent was carried out using 1.0 mol/L of HCl solution. The optimum sample flow rate and eluent flow rate were, respectively, 1.0 and 0.3 mL/min. Common coexisting ions did not interfere with the separation and determination of the target ions. The accuracy of the proposed method was validated by analysis of the standard reference material (GBW 08301, river sediment). The measured contents of metal ions in the reference material were in good agreement with the certified values. The presented method was successfully applied for the determination of Cu²⁺, Ni²⁺ and Zn²⁺ ions in three different water samples (well water, seawater and waste water).     

Preparation of PSSS‐grafted polysulfone microfiltration membrane and its rejection and removal properties towards heavy metal ions

3‐Hydroxy‐N,N‐diethylaniline (HDEA) as a tertiary aromatic amine was introduced onto the surface of chloromethylated polysulfone (CMPSF) microfiltration membrane through modification reaction, resulting in the modified membrane PSF‐DEA. A redox surface‐initiating system (DEA/APS) was constituted by the bonded tertiary aromatic amine group DEA and ammonium persulfate (APS) in aqueous solution, and so, the free radicals formed on the membrane initiated sodium p‐styrenesulfonate (SSS) as an anionic monomer to produce graft polymerization, getting the grafting‐type composite microfiltration membrane, PSF‐g‐PSSS membrane. Subsequently, the adsorption property of PSF‐g‐PSSS membrane for three heavy metal ions, Pb²⁺, Zn²⁺, and Hg²⁺ ions, was fully examined, and the rejection performance of PSF‐g‐PSSS membrane towards the three heavy metal ions was emphatically evaluated via permeation experiments. The experimental results show that by the initiating of the surface‐initiating system of DEA/APS, the graft polymerization can smoothly be carried out under mild conditions. PSF‐g‐PSSS membrane as a functional microfiltration membrane has strong adsorption ability for heavy metal ions by right of strong electrostatic interaction (or ion exchange action) between the anionic sulfonate ions on the membrane and heavy metal ions. The order of adsorption capacity is Pb²⁺ > Zn²⁺ > Hg²⁺, and the adsorption capacity of Pb²⁺ ion gets up to 2.18 μmol/cm². As the volume of permeation solutions, in which the concentrations of the three metal ions are 0.2 mmol/L, are in a range of 50 to 70 mL, the rejection rate of PSF‐g‐PSSS membrane for the three heavy metal ions can reach a level of 95%, displaying a fine rejection and removing performance towards heavy metal ions.     

Effect of counterion condensation on the acid-base equilibrium of a pH-sensitive merocyanine dye covalently attached to polyelectrolytes

Effects of monovalent and divalent counterions on the acid-base equilibrium of a pH-sensitive merocyanine dye covalently attached to copolymers of acrylic acid and acrylamide with varying charge densities (0.28 < ξ < 2.8) were investigated. Added chloride salts of Li⁺, Na⁺, K⁺, and NH⁺₄ (< 0.2 mM) had essentially no effect on pK observed (pK^obs) for the equilibrium. By contrast, the salts of Mg²⁺, Ca²⁺, Sr²⁺, and Ba²⁺ caused a significant decrease in pK^obs for the copolymers with larger ξ. With smaller ξ, most likely when ξ < 0.5, no decrease in pK^obs was observed upon addition of the salts of divalent cations. A competitive effect of Ca²⁺ and Na²⁺ ions on pK^obs in the presence of an excess of Na⁺ ions implied that Ca²⁺ ions at very low concentrations were preferentially, and therefore exhaustively, condensed on the polyanions with sufficiently large ξ probably until effective charge density was lowered to 0.5. The observed difference in the influence of the monovalent and divalent cations on pK^obs was discussed in terms of the difference in the microscopic behavior of the condensed monovalent and divalent cations. © 1993 John Wiley & Sons, Inc.     

锰(Ⅲ)离子与羧酸或α-羟基羧酸体系引发丙烯酰胺聚合

 锰(Ⅲ)离子可以引发烯类单体自由基聚合。羧酸,α-羟基羧酸对丙烯酰胺聚合有促进作用,其活性顺序为羟基多元羧酸(柠檬酸)>羟基羧酸(乳酸)>羧酸(正丁酸)。测定了在较高酸性([H⁺]=3.0M)的硫酸水溶液中,单独Mn³⁺,Nn³⁺-乙醇酸,Mn³⁺-乳酸引发丙烯酰胺聚合的活化能与动力学方程。     

Aqueous solutions of colloidal nickel: Radiation-chemical preparation, absorption spectra, and properties

Radiation-chemical reduction of Ni²⁺ ions in aqueous solutions of Ni(ClO₄)₂ containing sodium formate or isopropyl alcohol was studied, γ-Irradiation of deaerated solutions in the presence of polyethyleneimine, polyacrylate, or polyvinyl sulfate gives stable metal sols containing spherical particles 2–4 nm in diameter. The optical absorption spectra of nickel nanoparticles exhibit a band with a maximum at 215±5 nm (ε₂₁₅=4.7·10³ L mol⁻¹ cm⁻¹) and a shoulder at 350 nm. A mechanism for the radiation-chemical reduction of Ni²⁺ ions by hydrated electrons and organic radicals (CO₂- radical anions in the case of HCOONa and Me₂C·OH radicals in the case of PrⁱOH). The redox potentials of the Ni²⁺/Ni⁰ and Ni⁺/Ni⁰ pairs (Ni⁰ is a nickel atom) are approximately −2.2 and −1.7 V, respectively. The nanoparticles are readily oxidized by O₂, H₂O₂, and other oxidants. The reactions of these species with silver ions yield relatively stable nanoaggregates containing both nickel and silver in addition to silver nanoparticles. Published inIzvestiya Akademii Nauk, Seriya Khimicheskaya, No. 10, pp. 1733–1739, October, 2000.     

Tris-o-phenanthrolineiron(lll) Complex as a Photoinitiator of Acrylamide Polymerization

Abstract

The blue Tris-o-phenanthrolineiron(m) complex, Fe(phen)₃ ³⁺, formed in aqueous solution by oxidation of the red ferrous phenanthroline complex by nitric acid, is found to be a good photo-initiator of acrylamide (A.AM) polymerization. Systematic study of the kinetics of polymerization of acrylamide by Fe(phen) ₃ ³⁺ in aqueous nitric acid solution in the presence of light of Δ = 365 nm at room temperature showed that the rate of polymerization R_p was dependent on [A.AM]^1,5, [C] ^0,5, I^0,5, and [HCOOH], and the rate of Fe(phen) ₃ ³⁺disappearance, -R_c, was found to be proportional to [A.AM], [C], I, and [HCOOH], where [A.AM], [C] and [HCOOH] refer to the concentrations of acrylamide, Fe(phen) ₃ ³⁺, and formic acid, respectively, and I refers to light intensity. The kinetic observations are consistent with the interaction of the excited Fe(phen) ₃ ³⁺ with acrylamide molecule to produce a radical R. capable of initiation and also reduction of Fe(phen) ₃ ³⁺, to the stable Fe(phen) ₃ ²⁺. The results of the present study differ from those reported for photo initiation by ion pairs of the type Fe ³⁺X ^n- where ×= CI^?, Br^?, C₂O₄ ^2- OH^?, etc., which may be attributed to differences in the photo-behavior of the two systems.     

Radiation (60Co)-Induced Graft Copolymerization of Acrylamide on Jute Fiber

The radiation induced graft copolymerization of acrylamide onto jute fibers was studied following preirradiation of jute in air using a⁶⁰Co source of γ-radiation and subsequent polymerization of acrylamide in a limited aqueous system under nitrogen at 607°C. An increase of the time of preirradiation (at a fixed dose rate) increased the percent grafting measurably and the grafting efficiency marginall Grafting effects showed further improvement on addition of Fe²⁺ or Co²⁺ ions to the system prior to the polymerization step. Increasing the concentration of Fe²⁺ or Co²⁺ ion led to an increase in the grafting parameters with a leveling off effect in the higher concentration range, however. An increase in the polymer (jute) content for a fixed monomer content produced a significant increase in the efficiency of grafting, while % grafting followed a slowly decreasing trend.     

Graft polymerization kinetics of acrylamide initiated by ceric nitrate–dextran redox systems

The kinetics of the graft polymerization of acrylamide initiated by ceric nitrate—dextran polymeric redox systems was studied primarily at 25°C. Following an initial period of relatively fast reaction, the rate of polymerization is first-order with respect to the concentrations of monomer and dextran and independent of the ceric ion concentration. The equilibrium constant for ceric ion—dextran complexation K is 3.0 ± 1.6 l./mole, the specific rate of dissociation of the complex, k_d, is 3.0 ± 1.2 × 10^?4 sec.^?1, and the ratio of polymerization rate constants, k_p/k_t, is 0.44 ± 0.15. The number-average degree of polymerization is directly proportional to the ratio of the initial concentrations of monomer and ceric ion and increases exponentially with increasing extent of conversion. The initial rapid rate of polymerization is accounted for by the high reactivity of ceric ion with cis-glycol groups on the ends of the dextran chains. The polymerization in the slower period that follows is initiated by the breakdown of coordination complexes of ceric ions with secondary alcohols on the dextran chain and terminated by redox reaction with uncomplexed ceric ions.     

A New Silver(I) Potentiometric Sensor Based on a Calix[4]arene Substituted at the Narrow Rim by Amide/Phosphoryl Groups

A coated‐wire type silver ion‐selective electrode has been constructed using a modified p‐tert‐butyl‐calix[4]arene by amide‐phosphoryl groups, named 5, 11, 17, 23‐tetra‐tert‐butyl‐25, 27‐bis(diethylcarbamoylmethoxy)‐26,28‐bis(diphenylphosphinoylmethoxy)calix[4]arene (Calix), as neutral carrier. A plasticized PVC membrane containing 30% PVC, 60% ortho‐nitrophenyloctylether (NPOE), 2% sodium tetraphenylborate (NaTPB) and 8% “Calix” was coated on a graphite rod. The prepared electrode exhibited a linear Nernstian response over the range 1 × 10^?6 to 1 × 10^?2 M with a slope 58.4 (±0.2) mV per decade change and a detection limit of 6.3 × 10^?7 M. The working pH range of the sensor is 4‐6.7. It is found that the dynamic response time of the electrode to achieve a steady potential was very fast (～11 s). The selectivity of the sensor relative to NH₄⁺, Li⁺, Na⁺, K⁺, Ca²⁺, Sr²⁺, Ba²⁺, Mn²⁺, Pb²⁺, Co²⁺, Ni²⁺, Cu²⁺, Zn²⁺, Cd²⁺, Fe³⁺, La³⁺, Sm³⁺ and Th⁴⁺ was examined. The prepared electrode exhibits adequate stability with good reproducibility (57.6 ± 0.5 mV per decade change for 10 weeks). It was successfully used as an indicator electrode in potentiometric titration of silver ions with standard solution of EDTA. The sensor was also used for silver ion measurements in various synthetic samples.     

Highly selective colorimetric naked-eye Cu2+ detection using new bispyrazolone silver nanoparticle-based chemosensor

In this work, we have successfully developed novel silver nanoconjugates of pyrazolone analogue and screened its chemosensing potential in aqueous medium. Bispyrazolone silver nanoparticles (Bispyra-AgNPs) were synthesised and characterised through FTIR, UV-visible spectroscopy and atomic force microscopy. The sensing ability was explored towards Ca²⁺, Cd²⁺, Co²⁺, Cu²⁺, Fe²⁺, Li⁺, Pb²⁺, La³⁺, Hg²⁺, Mg²⁺, Ni²⁺ and Ba²⁺ metal ions, respectively. Bispyra-AgNPs showed a highly quenching potential in selective recognition of Cu²⁺and colour of the solution immediately turned from yellow to purple, after the addition of Cu²⁺ in to the solution. The developed method also displayed a remarkable selectivity for Cu²⁺ over others interfering metal ions. The binding ratio and stoichiometry of host-guest complex was found to be 1:1 and determined by Job’s method. The propose method is facile and sensitive to detect Cu²⁺ with detection limit of 10 µM.     

Separation and Speciation of Iron Ions by Using Colorimetric Hydrogels

In this study, Fe³⁺ ion selective N-(Rhodamine-6G)lactam-N'-acryloyl-ethylenediamine (RH6GAC) monomer was synthesized. Then, p(Acrylamide-co-N-(Rhodamine-6G)lactam-N'-acryloyl-ethylenediamine) (p(AAm-co-RH6GAC)) and p(2-hydroxyethyl- methacrylate-co- N-(Rhodamine-6G)lactam-N'-acryloyl-ethylenediamine) (p(HEMA-co-RH6GAC)) colorimetric hydrogels were synthesized by using acrylamide (AAm) and 2-hydroxyethylmethacrylate (HEMA) as primary monomers. FT-IR, SEM, polymerization yield and swelling characterizations were conducted for the resulting hydrogels. Then, these hydrogels were used in selective absorption of Fe³⁺ ions from aqueous media. The hydrogels, which could absorb Fe³⁺ ions selectively from a mixture of metal ions, were used as column packing material. The solutions containing Fe²⁺ and Fe³⁺ ions at different concentrations were separated at a rate of 97.7 ± 0.7%.     

Synthesis and reactivity of metal-containing monomers 49. Synthesis and structure of low-valence transition metal acrylates and their polymers

The methods for synthesis of Cu¹⁺, Fe²⁺, Cr²⁺, and V³⁺ acrylates were elaborated. The compounds obtained were characterized by elemental analyses, data of IR, X-ray photoelectron, and Mössbauer spectroscopy, magnetochemistry, and mass spectrometry. Polymeric products were obtained by liquid-phase radical polymerization of metal acrylates. Changes in the electronic state of the ions and their nearest ligand environment during polymerization were observed.