Design Consideration for a Two-Distributed-Junction Tuning Circuit

We describe a novel method of designing a tuning circuit with two half-wave distributed junctions separated by a half-wavelength microstripline, which analytically determines the circuit parameters such as the minimum current density of the junctions and the characteristic impedances of the distributed junctions and the microstripline. The tuning circuit was approximated by simple transmission theory and then simplified with ideal circuit components for analysis. We applied Chebyshevs band-pass filter theory, in part, to optimize the circuit design. The analytical results revealed that a high characteristic-impedance ratio between the distributed junctions and the microstripline is necessary to obtain broadband matching using low-current-density junctions. The experimental results for all-NbN SIS mixers we designed with this method demonstrated double-sideband (DSB) receiver-noise temperatures of 6–10 quanta from 710 to 810 GHz for a mixer with a current density of only 4 kA/cm² (estimated C_JR_N product of 37 at 750 GHz). The RF bandwidth was broader than that of a conventional full-wave distributed SIS mixer with the same current density.     

Simulation of Sub-harmonic SIS Mixers with a Full Five-Port Model

The performance of superconductor-insulator-superconductor (SIS) sub-harmonic mixers is thoroughly investigated in this paper. On account of the importance of the harmonic effect, a full five-port model combined with an enhanced Newton solution is applied to calculate the local oscillator (LO) waveform. The mixer performance is studied as functions of principal parameters including the embedding admittances, LO power and bias voltage. The results are compared with those from the quasi five-port model.     

A low-noise SIS receiver measured from 480 GHz to 650 GHz using Nb junctions with integrated RF tuning circuits

A heterodyne receiver using an SIS waveguide mixer with two mechanical tuners has been characterized from 480 GHz to 650 GHz. The mixer uses either a single 0.5 × 0.5 µm² Nb/AlO_x/Nb SIS tunnel junction or a series array of two 1 µm² Nb tunnel junctions. These junctions have a high current density, in the range 8 – 13 kA/cm². Superconductive RF circuits are employed to tune the junction capacitance. DSB receiver noise temperatures as low as 200 ± 17 K at 540 GHz, 271 K ± 22 K at 572 GHz and 362 ± 33 K at 626 GHz have been obtained with the single SIS junctions. The series arrays gave DSB receiver noise temperatures as low as 328 ± 26 K at 490 GHz and 336 ± 25 K at 545 GHz. A comparison of the performances of series arrays and single junctions is presented. In addition, negative differential resistance has been observed in the DC I–V curve near 490, 545 and 570 GHz. Correlations between the frequencies for minimum noise temperature, negative differential resistance, and tuning circuit resonances are found. A detailed model to calculate the properties of the tuning circuits is discussed, and the junction capacitance as well as the London penetration depth of niobium are determined by fitting the model to the measured circuit resonances.     

A 40 GHz band SIS receiver using Nb/Al?AlOx/Nb array junctions

A 40 GHz band SIS mixer receiver has been built using Nb/Al–AlOx/Nb array junctions and a 4.3 K closed cycle helium refrigerator. The minimum conversion loss of the mixer is 2±1 dB and the single sideband receiver noise temperature (T_RX (SSB)) is as low as 110±10 K at 36 GHz. T_RX (SSB) is almost constant in the IF bandwidth of 600 MHz. The mixer saturation level is as high as 15 nW, which is comparable to the injected LO power.Nobeyama Radio Observatory (NRO), a branch of the Tokyo Astronomical Observatory, University of Tokyo, is a cosmic radio observing facility open for outside users.     

A Low-Noise 230 GHz SIS Receiver for Radio Astronomy Employing Untuned Nb/AlOx/Nb Tunnel Junctions

A heterodyne receiver based on a 1/3 reduced height rectangular waveguide SIS mixer with two mechanical tuners has been built for astronomical observations of molecular transitions in the 230 GHz frequency band. The mixer used an untuned array (R_nC_j3, R_n70 ) of four Nb/AIOx/Nb tunnel junctions in series as a nonlinear mixing element. A reasonable balance between the input and output coupling efficiencies has been obtained by choosing the junction number N=4. The receiver exhibits DSB (Double Side Band) noise temperature around 50 K over a frequency range of more than 10 GHz centered at 230 GHz. The lowest system noise temperature of 38 K has been recorded at 232.5 GHz. Mainly by adjusting the subwaveguide backshort, the SSB (Single Side Band) operation with image rejection of 15 dB is obtained with the noise temperature as low as 50 K. In addition, the noise contribution from each receiver component has been studied further. The minimum SIS mixer noise temperature is estimated as 15 K, pretty close to the quantum limit v/k11 K at 230 GHz. It is believed that the receiver noise temperatures presented are the lowest yet reported for a 230 GHz receiver using untuned junctions.     

A Novel LO Power Injection Method for SIS Mixers

We propose a novel LO power injection method developed for SIS mixers in this paper. Based on the feature of extremely small LO power requirements of SIS quantum mixing, the new method fulfills SIS pumping through a DC/IF route based built-in LO path, which is composed of an additional LO waveguide and the existing microstrip choke filter on the junction substrate. With the new method, traditional external LO diplexers(e.g., crossguide-couplers or beamsplitters) become unnecessary, resulting in a lower loss, compact, and stable receiver system. Experiments at 110- and 230 GHz bands have shown that the present method is efficient in coupling sufficient pumping power to SIS junctions from general LO sources, and the receiver sensitivities have a further improvement of about 10 K. We expect this method is also able to be applied into submillimeter wave band for SIS mixers.     

An Integrated Sideband-Separating SIS Mixer Based on Waveguide Split Block for 100 GHz Band with 4.0–8.0 GHz IF

We have developed an integrated sideband-separating SIS mixer for the 100 GHz band based on the waveguide split block. The measured receiver noise temperatures with 4.0–8.0 GHz IF are less than 60 K in the LO frequency range of 90–110 GHz, and a minimum value of around 45 K is achieved at 100 GHz. The image rejection ratios are more than 10 dB in the frequency range of 90–110 GHz. We have installed the sideband-separating SIS mixer into an atmospheric ozone-measuring system at Osaka Prefecture University and successfully observed an ozone spectrum at 110 GHz in SSB mode. This experimental result indicates that the sideband-separating SIS mixer is very useful for astronomical observation as well as atmospheric observation.     

A Fixed-Tuned W-Band Waveguide SIS Mixer with 4.0-7.5 GHz IF

The design and performance of a fixed-tuned W-band SIS mixer with a wide band IF of 4.0-7.5 GHz is presented. Waveguide-to-stripline transition of the SIS mixer is designed using the lumped-gap-source port provided by HFSS^TM. Measured receiver noise temperature is less than 25 K in the frequency range of 95-120 GHz, with a minimum value of around 19 K achieved. Mixer noise temperature is determined to be about 8.5 K, which is around twice the quantum limit (i.e., 2hw/k). In spite of the high IF frequencies (f ₀ = 6 GHz), the performance of the SIS receiver is comparable or even superior to those of the best mechanically-tunable waveguide SIS receivers at low IF frequencies (f ₀ = 1.5 GHz). This result suggests that it is easy to design waveguide-to-stripline transitions without scale-model measurements.     

A Multibeam SIS Mixer Module for a Focal Plane Array Receiver

The integration of many receiver units into a receiver array is a common method of improvement of imaging systems. This approach, well known in the mm band for Schottky mixer arrays, has not so far been developed for Superconductor - Insulator - Superconductor (SIS) junction mixers, which give the best sensitivity in the short mm wave range and in the submm range.We demonstrate for the first time a practical low noise multibeam receiver module using SIS mixer technology. The basis for the integration of several SIS mixers with a common local oscillator source is given by the saturation of the SIS receiver noise dependence upon local oscillator power. The module comprises three identical SIS mixers integrated with a common local oscillator, coupled through a three branch waveguide directional coupler. The multibeam module has been developed for a focal plane array receiver of the 30 meter radio telescope of the Institut de Radioastronomie Millimétrique (IRAM).     

A Novel Circuit Architecture for High Performance of High-order Subharmonic Mixers

A novel circuit architecture for high performance of high-order subharmonic (SH) mixers is proposed in this paper. According to the specified harmonic mixing order, one or more mixer diodes sub-arrays and corresponding power divider as well as phase shift network for RF and LO signals are arranged in the circuit. This proposed SH mixer circuit has improved conversion loss, wide dynamic range and high port isolation for high-order SH mixers. By phase cancellation of idle frequencies, the proposed SH mixer circuit can eliminate complicated design procedure of idle frequency circuits; by phase cancellation of leakage LO power to RF and IF port, and leakage RF power to LO port, the mixer circuit can get high port isolation in LO-IF/RF and RF-LO. The increased antiparallel diode pairs in each sub-array will also lead to well performance by lowering effective series resistance. The proposed SH mixer circuit can be easily realized with power divider and phase shift network for RF and LO signals. Supported in part by National Natural Science Foundation of China (NSFC) under Grants 60621002 and in part by NSFC under Grants 60471017.