Cellulose based macromolecular chelator having pyrocatechol as an anchored ligand: synthesis and applications as metal extractant prior to their determination by flame atomic absorption spectrometry

Pyrocatechol is immobilized on cellulose via ---NH---CH₂---CH₂---NH---SO₂---C₆H₄---N=N--- linker and the resulting macromolecular chelator characterized by IR, TGA, CPMAS ¹³C NMR and elemental analyses. It has been used for enrichment of Cu(II), Zn(II), Fe(III), Ni(II), Co(II), Cd(II) and Pb(II) prior to their determination by flame atomic absorption spectrometry (FAAS). The pH ranges for quantitative sorption (98.0–99.4%) are 4.0–7.0, 5.0–6.0, 3.0–4.0, 5.0–7.0, 5.0–8.0, 7.0–8.0 and 4.0–5.0, respectively. The desorption was found quantitative with 0.5 mol dm⁻³ HCl/HNO₃ (for Pb). The sorption capacity of the matrix for the seven metal ions has been found in the range 85.3–186.2 μmol g⁻¹. The optimum flow rate of metal ion solution for quantitative sorption of metal onto pyrocatechol functionalized cellulose as determined by column method, is 2–6 cm³ min⁻¹, whereas for desorption it is 2–4 cm³ min⁻¹. The tolerance limits for NaCl, NaBr, NaI, NaNO₃, Na₂SO₄, Na₃PO_4, humic acid, EDTA, ascorbic acid, citric acid, sodium tartrate, Ca(II) and Mg(II) in the sorption of all the seven metal ions are reported. Ascorbic acid is tolerable up to 0.8 mmol dm⁻³ with Cu and Pb where as sodium tartrate does not interfere up to 0.6 mmol dm⁻³ with Pb. There is no interference of NaBr, NaCl and NaNO₃ up to a concentration of 0.5 mol dm⁻³, in the sorption of Cu(II), Cd(II) and Fe(III) on to the chelating cellulose matrix The preconcentration factors are between 75 and 300 and t_1/2 values ≤5 min for all the metal ions. Simultaneous sorption of Cu, Zn, Ni and Co is possible at pH 5.0 if their total concentration does not exceed lowest sorption capacity. The present matrix coupled with FAAS has been used to enrich and determine the seven metal ions in river and tap water samples (relative standard deviation (R.S.D.) 1.05–7.20%) and synthetic certified water sample SLRS-4 (NRC, Canada) with R.S.D. 2.03%. The cobalt present in pharmaceutical vitamin tablets was also preconcentrated on the modified cellulose and determined by FAAS (R.S.D. 1.87%).     

New methods for acceleration of meat sample preparation prior to determination of the metal content by atomic absorption spectrometry

Focused microwave-assisted digestion and ultrasound leaching have been applied for the extraction of Pb, Cd, Cr, Cu, Fe, Zn, Ca, and Mg from raw meat. Semimembranous muscle (SM) of raw pig ham was used for optimizing both the digestion and extraction steps by multivariate approaches. The detection and quantification limits were 0.5 and 0.9 g kg^–1 for Pb, 0.06 and 0.1 g kg^–1 for Cd, 0.2 and 1.2 g kg^–1 for Cr, 0.4 and 3 g kg^–1 for Cu, 0.04 and 0.1 mg kg^–1 for Fe, 0.012 and 0.017 mg kg^–1 for Zn, 0.3 and 0.4 mg kg^–1 for Ca, and 0.01 and 0.03 mg kg^–1 for Mg. The precision, expressed as relative standard deviation (RSD), ranged between 2.5 and 9.6% for focused microwave-assisted digestion and between 3.5 and 10.6% for ultrasound leaching. The methods were then compared with a reference method and applied to a certified reference material (bovine muscle 184, from the BCR). The t-test, applied to the results obtained from focused microwave-assisted digestion, revealed that they are in agreement (p>0.01) with the certified and estimated values in the case of Pb, Cd, Cr, Cu, Fe, Ca, Mg, and Zn but not in that of Fe. In the case of ultrasound leaching, only the extraction of Pb, Cu, and Ca was quantitative. The method based on microwave digestion provides more accurate and precise results than ultrasound leaching. These new procedures have many advantages with regards to conventional methods, namely, reduction of the extraction time, simplification of the process, avoidance of chemical emissions to the atmosphere, and no losses of metals by volatilization.     

Cellulose functionalized with 8-hydroxyquinoline: new method of synthesis and applications as a solid phase extractant in the determination of metal ions by flame atomic absorption spectrometry

8-Hydroxyquinoline has been immobilized on cellulose via a moderate size NHCH₂CH₂NHSO₂C₆H₄NN linker and the resulting macromolecular chelator (and intermediates) characterized by infrared spectrometry, cross-polarization magic angle spinning (CPMAS) NMR spectrometry and thermogravimetric analysis (TGA). It has been used for enrichment of Cu(II), Zn(II), Fe(III), Ni(II), Co(II), Cd(II) and Pb(II) prior to their determination by flame atomic absorption spectrometry (FAAS), which are quantitatively sorbed (recoveries>97%) at pH 4.2-6.7, 4.2-7.5, 2.0-3.0, 5.3-6.7, 5.3-6.2, 6.2-9.0 and 4.2-5.3, respectively. The sorption capacity for the seven cations varies from 93.8 to 629.9 μmol g⁻¹. HCl or HNO₃ (1 mol dm⁻³) may be used to desorb all the cations. The optimum flow rate for sorption and desorption has been found to be 2-4 cm³ min⁻¹. The tolerance limits of electrolytes NaCl, NaBr, NaNO₃, Na₂SO₄, Na₃PO₄ and cations Ca²⁺ and Mg²⁺ (added as chloride and sulphate, respectively) in the sorption of all these metal ions are reported. The preconcentration factor is between 90 and 300. Simultaneous sorption of the cations other than iron(III) is possible if their total concentration does not exceed sorption capacity. The present matrix coupled with FAAS has been used to enrich and determine the seven metal ions in river water samples (R.S.D.<7.4%) and water samples having a composition similar to certified water sample SLRS-4 (NRC, Canada) with R.S.D. ∼2.3%.     

间接原子吸收法测定乳酸环丙沙星

研究了在弱酸性介质中，乳酸环丙沙星与雷氏盐定量生成缔合物的反应条件，以及通过原子吸收法测定沉淀中Cr的含量而间接测定乳酸环丙沙星含量的分析方法。线性范围在5－40mg/L，相对标准偏差为2．5％，回收率在98％－101％之间。     

Determination of thallium by furnace atomic absorption spectrometry

The analytical conditions for the determination of thallium by graphite furnace atomic absorption spectrometry were studied and optimized using the peak-height mode. The charring-atomization curves for thallium from different atomization surfaces were constructed and the optimum charring and atomization conditions were established. These atomization surfaces included pyrolytic graphite-, tantalum-, zirconium- and tungsten-coated graphite tubes. The effects of different inorganic acids on the absorbance of thallium from different surfaces were studied. Using tungsten carbide-coated tubes, the interference effects due to hydrochloric and perchloric acids were eliminated. The matrix modification technique was also investigated for increasing the maximum permissible charring temperature for thallium. The matrix modifiers used included tungsten, zirconium, nickel and tantalum. The effect of adding these modifiers were studied in the presence of different acids. Tungsten increased the maximum permissible charring temperature from 400 to 1000 °C.     

Electrochemical hydride generation atomic absorption spectrometry for determination of cadmium

An electrolytic hydride generation system for determination of another hydride forming element, cadmium, by catholyte variation electrochemical hydride generation (EcHG) atomic absorption spectrometry is described. A laboratory-made electrolytic cell with lead-tin alloy as cathode material is designed as electrolytic generator of molecular hydride. The influences of several parameters on the analytical signal have been evaluated using a Plackett-Burman experimental design. The significant parameters such as cathode surface area, electrolytic current, carrier gas flow rate and catholyte concentration have been optimized using univariate method. The analytical figures of merit of procedure developed were determined. The calibration curve was linear up to 20 ng ml⁻¹of cadmium. The concentration detection limit (3σ, n = 8) of 0.2 ng ml⁻¹ and repeatability (relative standard deviation, n = 7) of 3.1% were achieved at 10.0 ng ml⁻¹. It was shown that interferences from major constituents at high concentrations were significant. The accuracy of method was verified using a real sample (spiked tap water) by standard addition calibration technique. Recovery of 104% was achieved for Cd in the spiked tap water sample.     

8-Hydroxyquinoline anchored to silica gel via new moderate size linker: synthesis and applications as a metal ion collector for their flame atomic absorption spectrometric determination

The silica gel modified with (3-aminopropyl-triethoxysilane) was reacted with 5-formyl-8-hydroxyquinoline (FHOQ_x) to anchor 8-quinolinol ligand on the silica gel. It was characterised with cross polarisation magic angle spinning (CPMAS) NMR and diffuse reflectance infrared Fourier transformation (DRIFT) spectroscopy and used for the preconcentration of Cu(II), Pb(II), Ni(II), Fe(III), Cd(II), Zn(II) and Co(II) prior to their determination by flame atomic absorption spectrometry. The surface area of the modified silica gel has been found to be 227 m² g⁻¹ and the two pKa values as 3.8 and 8.0. The optimum pH ranges for quantitative sorption are 4.0–7.0, 4.5–7.0, 3.0–6.0, 5.0–8.0, 5.0–8.0, 5.0–8.0 and 4.0–7.0 for Cu, Pb, Fe, Zn, Co, Ni and Cd, respectively. All the metals can be desorbed with 2.5 mol l⁻¹ HCl or HNO₃. The sorption capacity for these metal ions is in range of 92–448.0 μmol g⁻¹ and follows the order Cd3, NaCl, NaBr, Na₂SO₄ and Na₃PO₄, glycine, sodium citrate, EDTA, humic acid and cations Ca(II), Mg(II), Mn(II) and Cr(III) in the sorption of all the seven metal ions are reported. The preconcentration factors are 150, 250, 200, 300, 250, 300 and 200 for Cd, Co, Zn, Cu, Pb, Fe and Ni, respectively and t_1/2 values <1 min except for Ni. The 95% extraction by batch method takes ≤25 min. The simultaneous enrichment and determination of all the metals are possible if the total load of the metal ions is less than sorption capacity. In river water samples all these metal ions were enriched with the present ligand anchored silica gel and determined with flame atomic absorption spectrometer (R.S.D.≤6.4%). Cobalt contents of pharmaceutical samples (vitamin tablet) were preconcentrated with the present chelating silica gel and estimated by flame AAS, with R.S.D.1.4%. The results are in the good agreement with the certified value, 1.99 μg g⁻¹ of the tablets. Iron and copper in certified reference materials (synthetic) SLRS-4 and SLEW-3 have been enriched with the modified silica gel and estimated with R.S.D.<5%.     

Mercury determination by cold vapor atomic absorption spectrometry utilizing UV photoreduction

A method for the determination of mercury via UV photoreduction has been investigated. Mercury vapor was generated by the reduction of mercury species in an acetic acid solution using UV radiation. Detection of the volatile mercury was accomplished by atomic absorption spectrometry. An optimized system was found to provide a detection limit (defined as the concentration giving a signal equal to three times the standard deviation of the blank) of 2.1 μg L⁻¹ with a precision of 2.9% relative standard deviation (n = 8) for a 500 μg L⁻¹ mercury standard. The effect of various metal ions on the mercury signal was investigated and the method validated with a NRCC certified dogfish liver material (DOLT-3) using the method of standard additions. A reaction pathway is hypothesized for UV photoreduction.     

Metal furnace heated by flame as a hydride atomizer for atomic absorption spectrometry: Sb determination in environmental and pharmaceutical samples

The present work describes a metallic hydride atomizer for atomic absorption spectrometry, by evaluating the performance of the Inconel 600^® tube. For this purpose, stibine was used as the model volatile compound and antimony determination in river and lake sediments and in pharmaceutical samples was carried out to assess the metal furnace performance. Some parameters are evaluated such as those referring to the generation and transport of the hydride (such as KBH₄ and acid concentrations, carrier gas flow rate, injected volume, etc.), as well as those referring to the metal furnace (such as tube hole area, flame composition, long-term stability, etc.). The method presents linear Sb concentration from 2 to 80 μg L⁻¹ range (r > 0.998; n = 3) and the analytical frequency of ca. 140 h⁻¹. The limit of detection (LOD) is 0.23 μg L⁻¹ and the precision, expressed as R.S.D., is less than 5% (40 μg L⁻¹; n = 10). The accuracy is evaluated through the reference materials, and the results are similar at 95% confidence level according to the t-test.     

原子吸收和原子荧光光谱分析

本文是《分析试验室》期刊定期评述中关于原子吸收光谱法 ( AAS)及原子荧光光谱法 ( AFS)分析的第 8篇综述文章。文中对 1 999年～ 2 0 0 0年 1 1月期间我国在 AAS/AFS领域所取得的主要进展进行评述。内容包括 :概述、仪器装置与数据处理、火焰原子吸收光谱法、电热原子吸收光谱法、化学蒸气发生技术以及原子荧光光谱法。共收集文献 2 96篇。     

Extraction as a method for preparation of vegetable samples for the determination of trace metals by atomic absorption spectrometry

An alternative, simple and rapid technique was developed for a quantitative isolation of the group of eight elements: Al, Ca, Cd, Cu, Fe, Mg, Pb and Zn from vegetable material samples in an open system with the use of acids: conc. HCl, dil. HNO₃ and hydrofluoric acids. Equivalence of both the extractants, HCl and HNO₃, was found suitable for a quantitative isolation of Ca, Cu, Mg, Zn, Pb and Cd. For lead and cadmium, however, dil. HNO₃ proved to be more suitable because these elements are determined by the graphite furnace atomic absorption spectrometry (GF-AAS) technique. A quantitative dissolution of Al and Fe requires hydrofluoric acid as an additional extractant. The proposed method allows to obviate the organic matrix destruction stage, shorten the analyte dissolution time, reduce cost, and minimize hazards of loss and contamination. Validity and versatility of the method developed was verified by the analysis of standard reference materials.     

Procedure for dissolving wolframite in order to determine trace elements by atomic absorption spectrometry

An analytical procedure for dissolving wolframite in order to determine trace elements by atomic absorption is reported. After decomposition of the mineral by alkaline fusion, the cooled flux is dissolved by heating with aqua regia. The finely crystalline precipitate of tungstite, which forms on standing, is filtered and dissolved by heating with aqua regia. Tungstite forms again in the latter solution and the filtration and solubilization are repeated until the solution contains negligible amounts of trace elements. Following this procedure, trace elements in 35 samples of natural wolframite have been dissolved and the solutions obtained have been analyzed by atomic absorption spectrometry for Fe, Mn, Cu, Zn, Pb, Co, Ni and Cd.     

Use of atomic absorption spectrometry for the determination of metals in sediments in south-west Louisiana

The relatively recent introduction of atomic absorption spectrometry has produced a rapid and relatively inexpensive method for the determination of metal concentrations in a wide variety of samples. One such application is in the determination of metal concentrations in soils and sediments. Soils and sediments represent concentrated reservoirs for these metals that serve as sinks for introduced trace metals or can become environmental sources. The coastal zone of Louisiana provides a ‘living laboratory’ to investigate the mechanisms of transport, deposition, and dissolution of trace metals into this fragile environment. Investigations done in the coastal zone have found trace metals tend to concentrate near pollution inputs and sources and have not migrated to or significantly impacted the coastal zone of Louisiana. Common trace metals determined and their range of concentrations in coastal soil and sediments are chromium (10–30 ppm), copper (10–25 ppm), iron (0.6–2.1%), manganese (200–600 ppm), nickel (6–20 ppm), lead (8–20 ppm), and zinc (30–55 ppm).     

原子吸收法间接测定呋喃唑酮

运用原子吸收法间接测定了呋喃唑酮片剂中的呋喃唑酮。方法基于呋喃唑酮在N,N-二甲基甲酰胺（DMF）与乙醇的混合溶剂中与Zn-NH4Cl反应生成胲,胲与Tollens试剂按1：2的关系反应生成单质Ag沉淀,通过测定上清液中剩余Ag的原子吸收光度来间接测定呋喃唑酮。已用于呋喃唑酮片剂中呋喃唑酮的测定。     

Trace elemental determination in alcohol automotive fuel by electrothermal atomic absorption spectrometry

Suitable analytical methodologies were developed allowing direct determination of As, Cu, Fe, Pb, Sb and Sn in alcohol fuel samples by electrothermal atomic absorption spectrometry. Different chemical modification approaches were tested and compared in terms of analytical performance and in practical terms. Experimental conditions were optimized allowing little sample dilution and use of calibration curves prepared with aqueous inorganic analyte standards. Methodologies were tested with analyte spiked alcohol samples. Good analyte recoveries from spiked alcohol samples, precision better than 10% and limits of detection in the sub μg l⁻¹ range were achieved.     

Study of interferences by transition metal ions in hydride generation atomic absorption spectrometry of antimony

The mechanism of the interference of metal ions in the hydride generation atomic absorption spectrometry (AAS) of antimony was studied. Experiments on the decomposition rate of sodium tetrahydroborate in acidic media were done in the presence of interfering metals, with and without the addition of masking agents. The results were compared with experiments on the sensitivity of AAS in the presence of the same interfering metals with and without the addition of the same masking agents. AAS experiments are described in which the product of the reaction between sodium tetrahydroborate and one of the interfering metals was present during hydride formation. This reaction product was certainly one of the causes of interference, but the contribution of the catalytic decomposition of sodium tetrahydroborate to interference is not clear.     

On-line electrolytic dissolution of solid metal samples and determination of copper in aluminium alloys by flame atomic absorption spectrometry

A flow-injection system was developed in which alloy metal samples are electrolytically dissolved and the dissolved samples are analysed by flame atomic absorption spectrometry (FAAS). The effects of electrolyte composition and electrolysis parameters on the dissolution of the sample were studied. The method was used for the determination of copper in aluminium alloys. Electrolyte solutions consisting of 0.2–1.0 M nitric acid are better than other electrolytes tested with regard to both alloy sample dissolution and determination of copper by FAAS. The peak height increases linearly with the electrolysis time or current within a certain range. The detection limit depends on the sensitivity of the detector used, and can be improved by increasing the electrolysis time or current. Generally, aluminium alloys containing 0.5–10% copper can give suitable signals for FAAS determination. The reproducibility of electrolysis and determination is about 4% for the same sampling points and 5% for different sampling points on the alloy sample.     

The development of sputtering techniques and their application to atomic absorption spectrometry

The concept of using cathodic sputtering to generate atoms for chemical analysis by atomic absorption spectroscopy originated with Alan Walsh in the late 1950s. This article reviews the major developments in sputtering techniques and their application to analytical atomic absorption and fluorescence spectroscopy     

Vapour-phase acid decomposition of highly pure silicas in a sealed PTFE bomb and determination of impurities by “one-drop” atomic spectrometry

Using a sealed double PTFE vessel with a stainless-steel jacket, the purification of acids used in the vapour phase for the decomposition of highly pure silicas was carried out simultaneously in the same vessel at an elevated temperature. A significant decrease in the metal blank level, even from artificially contaminated acids containing 1 mg of each metal (Al, Ti, Cu, Fe, Mn, Ca, Mg and Na), was observed. By “one-drop” flame atomic absorption and “one-drop” inductively coupled plasma atomic emission spectrometry, Na, Ca, Mg, Cu, Fe, Mn and Ti in silicas were successfully determined owing to the very low blank level. This decomposition method made the determination of trace metals except aluminium in highly pure silicas possible without any other preconcentration step. Aluminium was determined only with the use of a small sample mass, owing to the poor decomposition by acid vapours.     

On-line precipitation/dissolution system for the preconcentration and determination of manganese traces by atomic absorption spectrometry

Flame atomic absorption spectrometry was used for the determination of Mn in biological material following preconcentration by precipitation. The proposed preconcentration method is based on the continuous precipitation of Mn(II) as hydrated Mn(IV) oxide in ammonia buffer and dissolution of the precipitate with hydrogen oxalate or dilute nitric acid. The sensitivity of the Mn determination is increased by the presence of hydrogen peroxide, which raises the rate of oxidation of Mn(II) to Mn(IV). By using a time-based technique (at a sample loading rate of 4 ml min⁻¹) a concentration factor of up to 55 was obtained using 24 ml of sample. The effect of concurrent cations was investigated; the most adverse effect was exerted by Fe(III), which interfered at concentrations 50 times higher than that of Mn(II).