Comparison of conventional and total reflection excitation geometry for fluorescence X-ray absorption spectroscopy on droplet samples

X-ray absorption fine structure (XAFS) experiments in fluorescence mode have been performed in total reflection excitation geometry and conventional 45°/45° excitation/detection geometry for comparison. The experimental results have shown that XAFS measurements are feasible under normal total reflection X-ray fluorescence (TXRF) conditions, i.e. on droplet samples, with excitation in grazing incidence and using a TXRF experimental chamber. The application of the total reflection excitation geometry for XAFS measurements increases the sensitivity compared to the conventional geometry leading to lower accessible concentration ranges. However, XAFS under total reflection excitation condition fails for highly concentrated samples because of the self-absorption effect.     

X-ray fluorescence imaging with polycapillary X-ray optics

X-ray fluorescence spectrometry imaging is a powerful tool to provide information about the chemical composition and elemental distribution of a specimen. X-ray fluorescence spectrometry images were conventionally obtained by using a μ-X-ray fluorescence spectrometry spectrometer, which requires scanning a sample. Faster X-ray fluorescence spectrometry imaging would be achieved by eliminating the process of sample scanning. Thus, we developed an X-ray fluorescence spectrometry imaging instrument without sample scanning by using polycapillary X-ray optics, which had energy filter characteristics caused by the energy dependence of the total reflection phenomenon. In the present paper, we show that two independent straight polycapillary X-ray optics could be used as an energy filter of X-rays for X-ray fluorescence. Only low energy X-rays were detected when the angle between the two optical axes was increased slightly. Energy-selective X-ray fluorescence spectrometry images with projection mode were taken by using an X-ray CCD camera equipped with two polycapillary optics. It was shown that Fe Kα (6.40 keV) and Cu Kα (8.04 keV) could be discriminated for Fe and Cu foils.     

Quantitative detection of antibody based on single-molecule counting by total internal reflection fluorescence microscopy with quantum dot labeling

We presented a sensitive method to quantify antibody based on single-molecule counting by total internal reflection fluorescence microscopy with quantum dot labeling. In this method, the biotinylated monoclonal anti-human IgG molecules were immobilized on the silanized glass substrate surface. By the strong biotin-streptavidin affinity, streptavidin-coated quantum dots were labeled to the target molecules as fluorescent probe. Then, images of fluorescent spots in the evanescent wave field were obtained by a high-sensitivity electron multiplying charge-coupled device. Finally, the number of fluorescent spots corresponding to single molecules in the subframe images was counted, one by one. The linear range of 8.0 × 10⁻¹⁴ to 5.0 × 10⁻¹² mol L⁻¹ was obtained between the number of single molecules and the sample concentration.     

Recent results of synchrotron radiation induced total reflection X-ray fluorescence analysis at HASYLAB,beamline L

At the Hamburger Synchrotronstrahlungslabor (HASYLAB), Beamline L, a vacuum chamber for synchrotron radiation-induced total reflection X-ray fluorescence analysis, is now available which can easily be installed using the adjustment components for microanalysis present at this beamline. The detector is now in the final version of a Vortex silicon drift detector with 50-mm² active area from Radiant Detector Technologies. With the Ni/C multilayer monochromator set to 17 keV extrapolated detection limits of 8 fg were obtained using the 50-mm² silicon drift detector with 1000 s live time on a sample containing 100 pg of Ni.Various applications are presented, especially of samples which are available in very small amounts: As synchrotron radiation-induced total reflection X-ray fluorescence analysis is much more sensitive than tube-excited total reflection X-ray fluorescence analysis, the sampling time of aerosol samples can be diminished, resulting in a more precise time resolution of atmospheric events. Aerosols, directly sampled on Si reflectors in an impactor were investigated. A further application was the determination of contamination elements in a slurry of high-purity Al₂O₃. No digestion is required; the sample is pipetted and dried before analysis. A comparison with laboratory total reflection X-ray fluorescence analysis showed the higher sensitivity of synchrotron radiation-induced total reflection X-ray fluorescence analysis, more contamination elements could be detected. Using the Si-111 crystal monochromator also available at beamline L, XANES measurements to determine the chemical state were performed. This is only possible with lower sensitivity as the flux transmitted by the crystal monochromator is about a factor of 100 lower than that transmitted by the multilayer monochromator. Preliminary results of X-ray absorption near-edge structure measurements for As in xylem sap from cucumber plants fed with As(III) and As(V) are reported. Detection limits of 170 ng/l of As in xylem sap were achieved.     

Determination of low atomic number elements at trace levels in uranium matrix using vacuum chamber total reflection X-ray fluorescence

Determinations of low atomic number elements Na, Mg and Al present at trace concentrations in uranium matrix were made by vacuum chamber total reflection X-ray fluorescence spectrometer for the first time. For this purpose, synthetic samples of uranium with known amounts of these low atomic number elements were prepared by mixing different volumes of their solutions with U solution of high purity. The concentrations of these elements in the samples were in the range of 100–300 μg/g with respect to uranium and 10–20 μg/mL in the solutions. Major matrix uranium was separated by solvent extraction with 30% solution of tri-n-butyl phosphate in dodecane. After the solvent extraction, aqueous phase containing trace elements was mixed with Sc internal standard and the samples were analyzed by vacuum chamber total reflection X-ray fluorescence spectrometer having a Cr Kα excitation source. The total reflection X-ray fluorescence results obtained, after blank corrections, indicated an average deviation of 14% from the calculated concentrations of these low atomic number elements on the basis of their preparation. However, the total reflection X-ray fluorescence determined concentration of Mg was exceptionally lower than the calculated concentration in two samples. These studies have shown that vacuum chamber total reflection X-ray fluorescence is a promising technique for the determination of low atomic number elements in uranium matrix after its separation.     

A ratiometric fluorescent chemodosimeter for Cu(II) in water with high selectivity and sensitivity

Coumarin derivative 1 was synthesized as an efficient ratiometric chemodosimeter for the detection of Cu(II) in 99% water/DMSO (v/v) at pH 7.0. Mechanism studies suggested that 1 formed a complex with Cu(II) at 2:1 ratio accompanied by quenching of green fluorescence at 524 nm; when the solution was heated to 50 °C for 30 min, Cu(II)-promoted hydrolysis of coumarin lactone moiety of 1 occurred with bright blue fluorescence at 451 nm emerged. With fluorescence intensity ratio detection at 451 nm and 524 nm, 1 features an excellent sensitivity with the detection limit of 15 nmol L⁻¹ toward Cu(II) and a good selectivity over other metal ions.     

Quantitative analysis of human serum leptin using a nanoarray protein chip based on single-molecule sandwich immunoassay

We report a method for the quantitative analysis of human serum leptin, which is a protein hormone associated with obesity, using a nanoarray protein chip based on a single-molecule sandwich immunoassay. The nanoarray patterning of a biotin-probe with a spot diameter of 150 nm on a self-assembled monolayer functionalized by MPTMS on a glass substrate was successfully accomplished using atomic force microscopy (AFM)-based dip-pen nanolithography (DPN). Unlabeled leptin protein molecules in human serum were detected based on the sandwich fluorescence immunoassay by total internal reflection fluorescence microscopy (TIRFM). The linear regression equation for leptin in the range of 100 zM-400 aM was determined to be y = 456.35x + 80,382 (R = 0.9901). The accuracy and sensitivity of the chip assay were clinically validated by comparing the leptin level in adult serum obtained by this method with those measured using the enzyme-linked immunosorbent assay (ELISA) performed with the same leptin standards and serum samples. In contrast to conventional ELISA techniques, the proposed chip methodology exhibited the advantages of ultra-sensitivity, a smaller sample volume and faster analysis time.     

A sensitive flow-batch system for on board determination of ultra-trace ammonium in seawater: Method development and shipboard application

Combining fluorescence detection with flow analysis and solid phase extraction (SPE), a highly sensitive and automatic flow system for measurement of ultra-trace ammonium in open ocean water was established. Determination was based on fluorescence detection of a typical product of o-phthaldialdehyde and ammonium. In this study, the fluorescence reaction product could be efficiently extracted onto an SPE cartridge (HLB, hydrophilic–lipophilic balance). The extracted fluorescence compounds were rapidly eluted with ethanol and directed into a flow cell for fluorescence detection. Compared with the common used fluorescence method, the proposed one offered the benefits of improved sensitivity, reduced reagent consumption, negligible salinity effect and lower cost. Experimental parameters were optimized using a univariate experimental design. Calibration curves, ranging from 1.67 to 300 nM, were obtained with different reaction times. The recoveries were between 89.5 and 96.5%, and the detection limits in land-based and shipboard laboratories were 0.7 and 1.2 nM, respectively. The relative standard deviation was 3.5% (n = 5) for an aged seawater sample spiked with 20 nM ammonium. Compared with the analytical results obtained using the indophenol blue method coupled to a long-path liquid waveguide capillary cell, the proposed method showed good agreement. The method had been applied on board during a South China Sea cruise in August 2012. A vertical profile of ammonium in the South East Asia Time-Series (SEATS, 18° N, 116° E) station was produced. The distribution of ammonium in the surface seawater of the Qiongdong upwelling in South China Sea is also presented.     

Multilayer characterization by energy dispersive X-ray reflectivity technique

An experimental setup was developed to verify the feasibility of silicon drift detector to be used for the multilayer characterization by means of multilayer energy dispersive X-ray reflectivity. Such a detector allows high count rates up to 3 × 10⁵ cps and can be used in principle for the direct beam intensity measurement, which is to be done for the X-ray multilayer reflectivity patterns obtaining. A series of measurements were performed for Mo/B₄C multilayer sample. A quality of the experimentally obtained data turns out to be enough to perform a sample structure exploration using a numerical procedure of experimental data fitting. Due to low cost and short time, required for the measurements, an experimental technique proposed has a good perspective to be used for some practical applications in industry.     

Novel B,O-chelated fluorescent probe for nitric oxide imaging in Raw 264.7 macrophages and onion tissues

A novel fluorescent probe based on B,O-chelated dipyrromethene chromophore in far-visible and near-infrared spectral region (600–900 nm), boron chelated 8-(3,4-diaminophenyl)-3,5-bis(2-hydroxyphenyl)-4-bora-3a,4a-diaza-s-indancene (BOPB), has been first developed for nitric oxide (NO) imaging. BOPB, a turn-on fluorescent probe, can react with NO rapidly under physiological condition. The reaction product of BOPB with NO, BOPB-T, emits bright red fluorescence at 643 nm when excited at 622 nm. Meanwhile, BOPB-T displays high fluorescent quantum yield of 0.21 and good photostability. The selectivity for NO over other reactive oxygen/nitrogen species and ascorbic acid has been investigated and BOPB has good specificity for the detection of NO. MTT assay shows that the toxicity of BOPB (below 10 μM) to living cells can be neglected. Based on these investigations, BOPB has been used for NO imaging in Raw 264.7 cells and onion tissues. Meanwhile, mechanical injury to onion tissues results in a brighter fluorescence around the wound, which indicates that more NO has been produced in plant tissues in response to external stimuli. Our studies illustrate that BOPB has advantages of high sensitivity, low background interference and little photo damage on fluorescence imaging of NO.     

Label-free detection of adenosine based on fluorescence resonance energy transfer between fluorescent silica nanoparticles and unmodified gold nanoparticles

A sensitive and convenient strategy was developed for label-free assay of adenosine. The strategy adapted the fluorescence resonance energy transfer property between Rhodamine B doped fluorescent silica nanoparticles (SiNPs) and gold nanoparticles (AuNPs) to generate signal. The different affinities of AuNPs toward the unfolded and folded aptamers were employed for the signal transfer in the system. In the presence of adenosine, the split aptamer fragments react with adenosine to form a structured complex. The folded aptamer cannot be adsorbed on the surface of AuNPs, which induces the aggregation of AuNPs under high ionic concentration conditions, and the aggregation of AuNPs leads to the decrease of the quenching ability. Therefore, the fluorescence intensity of Rhodamine B doped fluorescent SiNPs increased along with the concentration of adenosine. Because of the highly specific recognition ability of the aptamer toward adenosine and the strong quenching ability of AuNPs, the proposed strategy demonstrated good selectivity and high sensitivity for the detection of adenosine. Under the optimum conditions in the experiments, a linear range from 98 nM to 100 μM was obtained with a detection limit of 45 nM. As this strategy is convenient, practical and sensitive, it will provide a promising potential for label-free aptamer-based protein detection.     

Total reflection X-ray fluorescence mercury analysis after immobilization on quartz surfaces

Quartz reflectors are a common substrate for total reflection X-ray fluorescence (TXRF) analysis. Especially low masses of trace elements can be determined on these surfaces. In the present work, various complexing reagents were immobilized on the surface of quartz reflectors. The reflectors were immersed in mercury solutions and selective mercury collection took place. The effect of immersion time was examined and a few minutes were found adequate. The reflectors were analysed for mercury by TXRF. Different complexing reagents showed different collection capabilities; 4-(2-pyridazo-resorcinol) gave the best among them. The effect of various experimental parameters was examined like pH, interferences from other ions, etc. Mercury speciation was successfully tested by comparing inorganic mercury results with the methyl mercury ones. A very good selectivity for inorganic mercury was found. It was achieved very good linearity in the 1-500 ng mL⁻¹ mercury concentration range and the minimum detection limit was equal to 2.5 ng mL⁻¹.     

A novel flow-through fluorescence optosensor for the sensitive determination of tetracycline

A flow-through fluorescence optosensor with Sephadex G-50 microbeads as solid support is developed for the sensitive determination of tetracycline (TC). The fluorescent TC derivative encapsulated in CTAB micelle structures is retained onto the surface of the microbeads packed into a fluorescent flow cell in a flow system, followed by measurement of the native fluorescence of the TC derivative on the bead surface. The retained TC derivative is easily stripped off with DI water from the bead surface by breaking-down the micelle structure. This offers a convenient and effective way for the regeneration of the used solid support with DI water as a carrier. Under the optimal conditions, a linear calibration graph is obtained within a range of 3-500 μg L⁻¹, along with a detection limit of 1.0 μg L⁻¹. The present solid surface fluorescence optosensor provides a 22-fold improvement on the detection sensitivity for TC in comparison with that derived by fluorescence detection in aqueous medium. The feasibility of this flow-through fluorescence optosensor is evaluated by analyzing TC in a commercial drug tablet and surface water samples.     

Exploring the distribution of copper-Schiff base complex covalently anchored onto the surface of mesoporous MCM 41 silica

A series of copper-Schiff base MCM 41 materials, synthesized by post-synthetic grafting, was studied by X-ray photoelectron spectroscopy (XPS) and nitrogen sorption (77 K) to explore distribution of the copper-Schiff base complex immobilized on the porous Si-MCM 41. Additional information on the physico-chemical properties of the functionalized materials was obtained by powder X-ray diffraction (XRD), atomic absorption spectroscopy (AAS), CHN microanalysis, FTIR spectroscopy, ²⁹Si and ¹³C CP MAS NMR spectroscopy. The effect of copper-Schiff base complex loading and reaction times on the surface properties of Si-MCM 41 (surface area and pore parameters) in addition to its distribution within the Si-MCM 41 was explored by nitrogen sorption and XPS coupled with argon etching. Argon etching of a surface to a depth of 45 Å confirmed that the copper-Schiff base complex was distributed both on the external surface (pore end) and within the pores of Si-MCM 41. The amount of complex located in the pores at this depth was about one-third of the amount detected on the external surface of MCM 41. Nitrogen sorption isotherms measured at 77 K confirmed the reduction in total pore volume and surface area was the result of pore narrowing of Si-MCM 41 following grafting of complex in the 8 h samples. A significant decrease in surface area and pore volume for the 20 h sample (longer reaction time), with the highest copper loading (0.65 mmol g⁻¹), confirmed pore blocking in this material. The uneven distribution of the copper complex between the external and internal surface of Si-MCM 41 was attributed to the bulky nature of the complex, which restricted access to the pores.     

X-ray nanoscale profiling of layer-by-layer assembled metal/organophosphonate films

The nanoscale structure of multilayer metal/phosphonate thin films prepared via a layer-by-layer assembly process was studied using specular X-ray reflectivity (XRR), X-ray fluorescence (XRF), and long-period X-ray standing wave (XSW) analysis. After the SiO(2) X-ray mirror surfaces were functionalized with a monolayer film terminated with phosphonate groups, the organic multilayer films were assembled by alternating immersions in (a) aqueous solutions containing Zr(4+), Hf(4+), or Y(3+) cations and then (b) organic solvent solutions of PO(3)-R-PO(3), where R was a porphyrin or porphyrin-square spacer molecule. The different heavy metal cations provided X-ray fluorescence marker layers at different heights within the different multilayer assemblies. The XSW measurements used a 22 nm period Si/Mo multilayer mirror. The long-period XSW generated by the zeroth-order (total external reflection) through fourth-order Bragg diffraction conditions made it possible to examine the Fourier transforms of the fluorescent atom distributions over a much larger q(z)() range in reciprocal space than previously achieved.     

An ultrasensitive method for the determination of melamine using cadmium telluride quantum dots as fluorescence probes

An ultrasensitive and simple method for the determination of melamine was developed based on the fluorescence quenching of thioglycolic acid (TGA) capped CdTe quantum dots (QDs) at pH 11.0. In strong alkaline aqueous solution, the selectivity of the method has been greatly improved due to most heavy metal ions show no interference as they are in the precipitation form or in their anion form. Furthermore, CdTe quantum dots have higher quantum yields at higher pH. The method has a wider concentration range and lower detection limit. The influence factors on the determination of melamine were investigated and the optimum conditions were determined. Under optimum conditions, the fluorescence intensity change of TGA coated CdTe quantum dots was linearly proportional to melamine over a concentration range from 1.0 × 10⁻¹¹ to 1.0 × 10⁻⁵ mol L⁻¹ with a correlation coefficient of 0.9943 and a detection limit of 5 × 10⁻¹² mol L⁻¹. The mechanism of fluorescence quenching of the QDs has been proposed based on the infrared spectroscopy information and electrophoresis experiments in presence of melamine under alkaline condition. The proposed method was employed to detect trace melamine in milk powder and pet feeds with satisfactory results.     

Determination of nucleic acids based on the fluorescence quenching of Hoechst 33258 at pH 4.5

It was found the strong fluorescence emitted by the bis-benzimidazole derivative Hoechst 33258 at 490 nm could be efficiently quenched in pH 4.5 buffer when nucleic acids were added. Analysis of fluorescence intensity showed that the procedure was a static quenching dominated one, which was also demonstrated by the electron absorption spectra and lifetime of the excited state. The binding constant and numbers of binding sites were obtained from the Scatchard plot. The decreased fluorescence intensity was in proportion to the concentration of nucleic acids in the range 40-1800 ng ml⁻¹ for dsDNA and 26-1700 ng ml⁻¹ for ssDNA. The limits of detection were 12 and 8 ng ml⁻¹, respectively. The sensitivity of the method was about 3.4 times higher for dsDNA detection and 5.4 times higher for ssDNA detection compared with the widely used fluorescence enhancement method using the same dye. Application results to synthetic samples showed simplicity, rapidity and satisfactory reproducibility of the presented method. Measurement of real samples extracted from leaves of Crassula argentea and E. coli genome also gave satisfactory results, which were in good agreement with those obtained using spectrophotometric method.     

Fluorescence single-molecule counting assays for protein quantification using epi-fluorescence microscopy with quantum dots labeling

A single-molecule counting approach for quantifying the antibody affixed to a surface using quantum dots and epi-fluorescence microscopy is presented. Modifying the glass substrates with carboxyl groups provides a hydrophilic surface that reacts with amine groups of an antibody to allow covalent immobilization of the antibody. Nonspecific adsorption of single molecules on the modified surfaces was first investigated. Then, quantum dots were employed to form complexes with surface-immobilized antibody molecules and used as fluorescent probes for single-molecule imaging. Epi-fluorescence microscopy was chosen as the tool for single-molecule fluorescence detection here. The generated fluorescence signals were taken by an electron multiplying charge-coupled device and were found to be proportional to the sample concentrations. Under optimal conditions, a linear response range of 5.0 × 10⁻¹⁴-3.0 × 10⁻¹² mol L⁻¹ was obtained between the number of single molecules and sample concentration via a single-molecule counting approach.     

Spectrofluorimetric determination of trace nitrite in food products with a new fluorescent probe 1,3,5,7-tetramethyl-2,6-dicarbethoxy-8-(3',4'-diaminophenyl)-difluoroboradiaza-s-indacene

A new fluorescent probe 1,3,5,7-tetramethyl-2,6-dicarbethoxy-8-(3′,4′-diaminophenyl)-difluoroboradiaza-s-indacene (TMDCDABODIPY) has been developed to detect nitrite in meat products and vegetables. The fluorescence of TMDCDABODIPY is very weak, but when it reacts with nitrite, a strong fluorescent triazole forms in aqueous medium at room temperature, which offers the advantage of specificity and sensitivity for the determination of nitrite. The fluorescence intensity was linear over a nitrite concentration of 9-300 nmol l⁻¹ with a detection limit of 0.21 nmol l⁻¹ (S/N = 3). The proposed method has been used for the determination of trace nitrite in food products with the recoveries of 94.62-105.48%.     

A versatile total internal reflection photometric detection cell for flow analysis

A total internal reflection (TIR) flow-through cell that is highly tolerant of schlieren effects, has limited hydrodynamic dispersion and does not trap gas bubbles, and which is suitable for sensitive photometric measurements in flow analysis, is described. Light from an optical fibre is introduced into a short length of quartz capillary through the sidewall at an incident angle of ca. 53°. Under this condition, incident light undergoes total internal reflection from the external air-quartz interface and is propagated by successive reflections from the external walls through the aqueous liquid core of the cell. Detection of the transmitted beam is enabled by intentionally introducing an optical coupling medium at a predetermined distance along the capillary wall, which allows the internally reflected light to be captured by a second optical fibre connected to a charge-couple device detector.This configuration embodies a number of the desirable features of a liquid core waveguide cell (i.e. total internal reflection), a multi-reflection (MR) flow cell (i.e. minimum susceptibility to schlieren effects, low hydrodynamic dispersion and little tendency to trap bubbles), and a conventional Z-cell (wide dynamic range). When employed with a flow injection system, a limit of detection of 2.0 μg PL⁻¹ was achieved for the determination of reactive phosphate using the TIR cell, compared with LOD values of 3.8 μg PL⁻¹ and 4.9 μg PL⁻¹ obtained using the MR and Z-cells with same manifold.The combined advantages of schlieren-tolerance and lack of bubble entrapment of the MR cell with the higher S/N ratio and wider dynamic range of a conventional Z-cell, make the TIR cell eminently useful for photometric measurements of samples with widely differing refractive indices.