Kinetics and thermodynamic study of aniline adsorption by multi-walled carbon nanotubes from aqueous solution

Multi-walled carbon nanotubes (MWCNTs) were used in the adsorptive removal of aniline, an organic pollutant, from an aqueous solution. It was found that carbon nanotubes with a higher specific surface area adsorbed and removed more aniline from an aqueous solution. The adsorption was dependent on factors, such as MWCNTs dosage, contact time, aniline concentration, solution pH and temperature. The adsorption study was analyzed kinetically, and the results revealed that the adsorption followed pseudo-second order kinetics with good correlation coefficients. In addition, it was found that the adsorption of aniline occurred in two consecutive steps, including the slow intra-particle diffusion of aniline molecules through the nanotubes. Various thermodynamic parameters, including the Gibbs free energy change (ΔG°), enthalpy change (ΔH°) and entropy change (ΔS°), were calculated. The results indicated that the spontaneity of the adsorption, exothermic nature of the adsorption and the decrease in the randomness reported as ΔG°, ΔH° and ΔS°, respectively, were all negative.     

Diglycolamide functionalized multi-walled carbon nanotubes for removal of uranium from aqueous solution by adsorption

Diglycolamide functionalized multi-walled carbon nanotubes (DGA-MWCNTs) were synthesized by sequential chemical reactions for removal of uranium from aqueous solution. Characterization studies were carried out using FT-IR spectroscopy, XRD and SEM analysis. Adsorption of uranium from aqueous solution on this material was studied as a function of nitric acid concentration, adsorbent dose and initial uranium concentration. The uranium adsorption data on DGA-MWCNTs followed the Langmuir and Freundlich adsorption isotherms. The adsorption capacity of DGA-MWCNTs as well as adsorption isotherms and the effect of temperature on uranium ion adsorption were investigated. The standard enthalpy, entropy, and free energy of adsorption of the uranium with DGA-MWCNTs were calculated to be 6.09 kJ mole⁻¹, 0.106 kJ mole⁻¹ K⁻¹ and −25.51 kJ mole⁻¹ respectively at 298K. The results suggest that DGA-MWCNTs can be used as efficient adsorbent for uranium ion removal.     

Hydrogen adsorption in defected carbon nanotubes

Recently there has been lot of interest in the development of hydrogen storage in various systems for the large-scale application of fuel cells, mobiles and for automotive uses. Hectic materials research is going on throughout the world with various adsorption mechanisms to increase the storage capacity. It was observed that physisorption proves to be an effective way for this purpose. Some of the materials in this race include graphite, zeolite, carbon fibers and nanotubes. Among all these, the versatile material carbon nanotube (CNT) has a number of favorable points like porous nature, high surface area, hollowness, high stability and light weight, which facilitate the hydrogen adsorption in both outer and inner portions. In this work we have considered armchair (5,5), zig zag (10,0) and chiral tubes (8,2) and (6,4) with and without structural defects to study the physisorption of hydrogen on the surface of carbon nanotubes using DFT calculations. For two different H₂ configurations, adsorption binding energies are estimated both for defect free and defected carbon nanotubes. We could observe larger adsorption energies for the configuration in which the hydrogen molecular axis perpendicular to the hexagonal carbon ring than for parallel to C–C bond configuration corresponding to the defect free nanotubes. For defected tubes the adsorption energies are calculated for various configurations such as molecular axis perpendicular to a defect site octagon and parallel to C–C bond of octagon and another case where the axis perpendicular to hexagon in defected tube. The adsorption binding energy values are compared with defect free case. The results are discussed in detail for hydrogen storage applications.     

Isolation of ethanol from its aqueous solution by liquid phase adsorption and gas phase desorption using molecular sieving carbon

A novel bioethanol separation process was proposed in this study employing molecular sieving carbon (MSC) as an adsorbent, whose pore diameter is close to molecular size of ethanol. In the proposed process, fermentation broth is first introduced to the adsorption bed packed with MSC. In this step, ethanol is selectively adsorbed onto MSC, with highly enriching ethanol in the micropore of MSC. Subsequently, the concentrated ethanol is desorbed from MSC to gaseous phase, resulting in further purification of ethanol owing to a considerable difference in desorption rate between water and ethanol; Because of molecular sieving effect of MSC, the desorption rate of ethanol is much smaller than that of water. To establish this process, adsorption equilibrium and kinetics of ethanol on various MSCs were investigated in aqueous phase as the first step. Also, desorption kinetics of ethanol and water in gaseous phase were investigated. As a result, it was suggested that highly concentrated ethanol could be obtained with high recovery ratio through these simple operations, meaning the proposed process is quite promising.     

Fluoride and lead adsorption on carbon nanotubes

The properties and applications of CNT have been studied extensively since Iijima discovered them in 1991[1,2]. They have exceptional mechanical properties and unique electrical property, highly chemical stability and large specific surface area. Thus far, they have widely potential applications in many fields. They can be used as reinforcing materials in composites[3], field emissions[4], hydrogen storage[5], nanoelectronic components[6], catalyst supports[7], adsorption material and so on.…     

Separation of carbon nanotubes in aqueous medium by capillary electrophoresis

A robust and reproducible method for the dispersion of carbon nanotubes, either single-walled or multi-walled is presented. Dispersion of nanotubes was achieved as surfactant-coated species of sodium dodecyl sulphate. The addition of small amounts of hydroxypropyl methyl cellulose (HPMC) together with the surfactant, sodium dodecyl sulphate, was found critical to achieve reproducible nanotubes dispersion and to obtain an homogeneous and stable solution. This solution is further analyzed by capillary electrophoresis using a background electrolyte solution containing a polymer, 0.025% (w/v) HPMC solution prepared in 5 mM ammonium acetate at pH 8.03. This electrophoretic method presents a high reproducibility between runs, being an interesting alternative to study nanotube size distribution or characterization after synthesis. In addition, the methodology developed allowed the study of the interaction of the different types of carbon nanotubes with a molecular probe such as pentachlorophenol. This procedure was showed effective to detect small differences on the chemical/physical surface properties of the nanotubes. The different interaction behavior found within the two SWNTs selected was critically discussed.     

Phenol adsorption on closed carbon nanotubes

We present the results of systematic studies of phenol adsorption on closed commercially available, unmodified carbon nanotubes. Phenol adsorption is determined by the value of tube-specific surface area, the presence of small amount of surface groups influence adsorption only in very small amount. Phenol can be applied as a probe molecule for comparative analysis of tube surface areas. Tube curvature influences adsorption from solution, i.e., we observe increasing adsorption energy (and slower desorption process) with the decrease in tube curvature. This is in full accordance with molecular simulation results.     

Functionalization of multiwalled carbon nanotubes by mild aqueous sonication

Sonication has been widely used in the dispersal of carbon nanotubes (CNTs) in various liquids as well as in their functionalization in aqueous acids. Here, for the first time, we study the sonication of multiwalled CNTs (MWCNTs) in deionized water. Our results indicate an improvement in the aqueous dispersal of MWCNTs as well as an increase in their adhesive interaction with Au substrates. Field emission scanning electron and high-resolution transmission electron microscopies as well as X-ray photoelectron, photoacoustic Fourier transform IR, and Raman spectroscopies have shown this to be due to the production of low concentrations of O-containing functionalizations (alcohol, carbonyl, acid, with the total O concentration being approximately 2%), without damaging the basic CNT structure; this production of functional groups is mirrored by the disappearance of -CH(n) groups existing on the pristine CNTs. These new functional groups are capable of hydrogen bonding, which plays an important role in their aqueous dispersal and enhanced substrate interactions.     

Molecular perspective on diazonium adsorption for controllable functionalization of single-walled carbon nanotubes in aqueous surfactant solutions

Functionalization of single-walled carbon nanotubes (SWCNTs) using diazonium salts allows modification of their optical and electronic properties for a variety of applications, ranging from drug-delivery vehicles to molecular sensors. However, control of the functionalization process remains a challenge, requiring molecular-level understanding of the adsorption of diazonium ions onto heterogeneous, charge-mobile SWCNT surfaces, which are typically decorated with surfactants. In this paper, we combine molecular dynamics (MD) simulations, experiments, and equilibrium reaction modeling to understand and model the extent of diazonium functionalization of SWCNTs coated with various surfactants (sodium cholate, sodium dodecyl sulfate, and cetyl trimethylammonium bromide). We show that the free energy of diazonium adsorption, determined using simulations, can be used to rank surfactants in terms of the extent of functionalization attained following their adsorption on the nanotube surface. The difference in binding affinities between linear and rigid surfactants is attributed to the synergistic binding of the diazonium ion to the local "hot/cold spots" formed by the charged surfactant heads. A combined simulation-modeling framework is developed to provide guidance for controlling the various sensitive experimental conditions needed to achieve the desired extent of SWCNT functionalization.     

Heterogeneity of multiwalled carbon nanotubes based on adsorption of simple aromatic compounds from aqueous solutions

The surface heterogeneity of multiwalled carbon nanotubes (MWCNTs) is studied on the basis of adsorption isotherms from dilute aqueous phenol and dopamine solutions at various pH values. The generalized Langmuir–Freundlich isotherm equation was applied to investigate the cooperative effect of the surface heterogeneity and the lateral interactions between the adsorbates. The theoretical isosteric heats of adsorption were obtained assuming that the heat of adsorption profile reveals both the energetic heterogeneity of the adsorption system and the strength of the interactions between the neighboring molecules. The adsorption energy distribution functions were calculated by using algorithm based on a regularization method. The great advantage of this method is that the regularization makes no assumption about the shape of the obtained energy distribution functions. Analysis of the isosteric heats of adsorption for MWCNTs showed that the influence of the surface heterogeneity is much stronger than the role of the lateral interactions. The most typical adsorption heat is 20–22 kJ/mol for both phenol and dopamine. After purification of nanotubes, heat value for phenol dropped to 16–17 kJ/mol. The range of the energy distribution is only slightly influenced by the surface chemistry of the nanotubes in the aqueous conditions.     

Simulated water adsorption in chemically heterogeneous carbon nanotubes

Grand canonical Monte Carlo simulations are used to study the adsorption of water in single-walled (10:10), (12:12), and (20:20) carbon nanotubes at 298 K. Water is represented by the extended simple point charge model and the carbon atoms as Lennard-Jones spheres. The nanotubes are decorated with different amounts of oxygenated sites, represented as carbonyl groups. In the absence of carbonyl groups the simulated isotherms are characterized by negligible amounts of water uptake at low pressures, sudden and complete pore filling once a threshold pressure is reached, and wide adsorption-desorption hysteresis loops. In the presence of a few carbonyl groups the simulated adsorption isotherms are characterized by pore filling at lower pressures and by narrower adsorption-desorption hysteresis loops compared to the results obtained in the absence of carbonyl groups. Our results show that the distribution of the carbonyl groups has a strong effect on the adsorption isotherms. For carbonyl groups localized in a narrow section the adsorption of water may be gradual because a cluster of adsorbed water forms at low pressures and grows as the pressure increases. For carbonyl groups distributed along the nanotube the adsorption isotherm is of type V.     

Bulk synthesis of linear carbon chains confined inside single-wall carbon nanotubes by vacuum discharge

Carbyne, an infinite carbon chain, has attracted much interest and induced significant controversy for many decades. Recently, the presence of linear carbon chains (LCCs), which were confined stably inside double-wall carbon nanotubes (DWCNTs) and multiwall carbon nanotubes (MWCNTs), has been reported. In this study, we present a novel method to produce LCCs in a film of carbon nanotubes (CNTs). Our transmission electron microscopy and Raman spectroscopy revealed the formation of a bulk amount of LCCs after electric discharge of CNT films, which were used as field emission cathodes. The LCCs were confined inside single-wall CNTs as well as DWCNTs. Furthermore, two or three LCCs in parallel with each other are encapsulated when the inner diameter of CNT is larger than approximately 1.1 nm.     

苯胺在碳纳米管上的吸附特征

苯胺是一种重要的有机化工原料,能通过皮肤和呼吸道进入人体而引起中毒,还会严重污染环境。目前,国内外处理含苯胺废水的方法主要有氧化法、萃取法、生化法、吸附法等。本文使用碳纳米管进行液相吸附除去苯胺。     

Adsorption of roxarsone from aqueous solution by multi-walled carbon nanotubes

Molecularly imprinted particle for bisphenol A (BPA-MIP) was prepared using the surface molecular imprinting technique with a sol-gel process on the surface of silica nanoparticles. The dosages of diethylenetriaminepentaacetic acid (DTPA) as a functional monomer and teraethyl orthosilicate (TEOS) as a cross-linker were optimized, respectively. The prepared BPA-MIP was characterized by scanning electron microscopy (SEM), energy dispersive spectrometer (EDS), Fourier transform infrared spectrometer (FTIR), thermogravimetric analysis (TGA), and a standard Brunauer-Emett-Teller (BET) analysis. Moreover, the proper binding and selective recognition ability were also investigated by a single batch binding experiment. The equilibrium data fitted well to the pseudo-second-order kinetic and the Langmuir model for BPA binding onto BPA-MIP, respectively. The saturate binding capacity of BPA-MIP was found to be 30.26 μmol g(-1), which was three times higher than that of BPA non-molecular imprinted particle (BPA-NIP). The satisfactory results demonstrated that the obtained BPA-MIP showed an appreciable binding specificity toward BPA than similar structural compounds in water phase. The BPA-MIP could serve as an efficient selective material for determining or removing BPA from water environment.     

Thermodynamics and kinetics of adsorption of Cu(II) from aqueous solutions onto multi-walled carbon nanotubes

Release of heavy metals into water as a result of industrial activities may pose a serious threat to the environment. The objective of this study is to assess the uptake of Cu²⁺ from aqueous solutions onto multi-walled carbon nanotubes (MWCNT). The potential of the t-MWCNT to remove Cu²⁺ cations from aqueous solutions was investigated in batch reactor under different experimental conditions. The processing parameters such as initial concentration of Cu²⁺ ions, temperature, and adsorbent mass were also investigated. Copper uptake was quantitatively evaluated using the Langmuir, Freundlich and Dubinin–Kaganer–Radushkevich (DKR) models. In addition, the adsorption equilibrium was described well by the Langmuir isotherm model with maximum adsorption capacity of 12.34 mg/g of Cu²⁺ cations on t-MWCNT. Various thermodynamic parameters, such as ΔG⁰, ΔH⁰ and ΔS⁰ were calculated. The thermodynamics of Cu²⁺ cations adsorption onto t-MWCNT system pointed at spontaneous and endothermic nature of the process. Using the second-order kinetic constants, the activation energy of adsorption (E_a) was determined as 27.187 kJ/mol according to the Arrhenius equation.     

Enthalpy and entropy effects in hydrogen adsorption on carbon nanotubes

Interaction energies and entropies associated with hydrogen adsorption on the inner and outer surfaces of zigzag single-wall carbon nanotubes (SWCNT) of various diameters are analyzed by means of molecular mechanics, density functional theory, and ab initio calculations. For a single molecule the strongest interaction, which is 3.5 greater than that with the planar graphite sheet, is found inside a (8,0) nanotube. Adsorption on the outer surfaces is weaker than that on graphite. Due to the steric considerations, both processes are accompanied by an extremely strong decline in entropy. Absence of specific adsorption sites and weak attractive interaction between hydrogen molecules within carbon nanotubes results in their close packing at low temperatures. Using the calculated geometric and thermodynamic parameters in Langmuir isotherms we predict the adsorption capacity of SWCNTs at room temperature to be smaller than 1 wt % even at 100 bar.     

Efficient H2 adsorption by nanopores of high-purity double-walled carbon nanotubes

DWNT buckypaper adsorbed much more hydrogen than did a SWNT bundle. XRD measurements and GCMC simulation results suggested that the DWNT bundle is loosely packed into an hexagonal array with interstitial pores which can efficiently adsorb H2 molecules.     

Adenosine,adenosine monophosphate,and adenosine triphosphate adsorption from aqueous solutions on the surface of multiwall carbon nanotubes

Adenosine, adenosine monophosphate, and adenosine triphosphate adsorption from aqueous solutions on the surface of carbon nanotubes is studied. Adsorption isotherms are plotted and adsorption free energies, as well as areas per molecules of the adsorbates, are calculated at their concentrations in solutions of 0–10⁻³ mol/dm³. It is shown that the monomolecular adsorption is characterized by rather loose packing of adsorbate molecules on the nanotube surface, with the packing density increasing in the presence and upon a rise in the concentration of phosphate groups in adsorbate molecules. In the range of the polymolecular adsorption, at high adsorbate concentrations in solutions (C > (5–6) × 10⁻⁴ mol/dm³), the adsorption decreases in a series adenosine > adenosine monophosphate > adenosine triphosphate, i.e., with an increase in the solubility of the examined compounds in water.     

Electrically conducting electrospun silk membranes fabricated by adsorption of carbon nanotubes

We present a simple method of obtaining electrically conducting electrospun silk non-woven membranes consisting of nanofibers with multi-walled carbon nanotubes (MWCNTs) adsorbed on their surface. Nanofibrous membranes with fibroin diameters of 460 ± 40 nm were formed from aqueous Bombyx mori fibroin solution by electrospinning. The MWCNTs adhered well to the surface of the highly porous silk nanofibrous membranes when Triton X-100 was used as the surfactant for the dispersion of the MWCNTs in aqueous media. The electrical conductivity of the membranes was 2.4 × 10⁻⁴ S/cm due to the presence of the MWCNTs on their surface. In addition, the strong interaction between the MWCNTs and nanofibers keeps them from separating each other, even after ultrasonication. The combination of the high conductivity of the membranes and the simple process used to fabricate them could lead to significant advances in the development of new materials, such as electromagnetic interference shielding or electrostatic dissipation membranes.     

Surface structure and adsorption properties of multiwalled carbon nanotubes

The pore structure, sorption parameters, and chemical composition of the surface of multiwalled carbon nanotubes synthesized by catalytic pyrolysis were determined. The dependences of the amount of cholic acid adsorbed by the nanotube surface on time, pH, and concentration of an equilibrium solution were studied. Physical adsorption of cholic acid is mainly the outcome of nonspecific interactions between the acid and the surface of the nanotubes. Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 10, pp. 1712–1715, October, 2006.