Polymer blend membranes of sulfonated poly(arylene ether ketone) for direct methanol fuel cell

The blend membranes of sulfonated poly(arylene ether ketone) (sPAEK) (IEC = 1.0 mequiv./g)/Nafion^® and the blend membranes of sPAEK (IEC = 1.0 mequiv./g)/sPAEK (IEC = 1.7 mequiv./g) were prepared. sPAEK with low IEC was introduced to reduce the methanol permeability through the membrane. Morphology, water uptake, proton conductivity and methanol permeability of the blend membranes were investigated by SEM, AFM, AC impedance spectroscopy and permeability measuring instrument. The cross-sections of blend membranes showed phase-separated morphologies. The effect of phase-separated morphology on the properties of blend membranes was investigated. The properties like water uptake, proton conductivity, and methanol permeability of sPAEK/Nafion^® blend membranes showed similar values with sPAEK and properties of sPAEK/sPAEK blend membranes showed intermediate values of two polymers due to the difference in morphology of the blend membranes. sPAEK/sPAEK blend membranes showed relatively high proton conductivity and lowered methanol permeability compared to Nafion^®. sPAEK/sPAEK blend membranes could be a competent substitution for Nafion^®.     

Fluorenyl-containing sulfonated poly(aryl ether ether ketone ketone)s (SPFEEKK) for fuel cell applications

A series of fluorenyl-containing sulfonated poly(aryl ether ether ketone ketone)s (SPFEEKK) were synthesized via aromatic nucleophilic substitution polymerization. The sulfonation content (SC) was controlled by the feed ratios of sulfonated and nonsulfonated monomers. Flexible and strong membranes in the sulfonic acid form were obtained from cast membranes in the sodium salt forms by treatment with acid. The thermal properties, water uptake, swelling ratio, water state, oxidative stability, proton conductivity and methanol permeability were investigated. All the polymers had proton conductivities greater than 1 × 10⁻² S/cm at room temperature, and the conductivity values of m-SPFEEKK-80 and p-SPFEEKK-80 were up to 1.86 × 10⁻¹ and 1.78 × 10⁻¹ S/cm at 100 °C. This series of polymers also possessed good dimensional stability in water and low methanol crossover.     

Sulfonated Poly(ether ether ketone) and Poly(ethylene glycol) Diacrylate Based Semi-Interpenetrating Network Membranes for Fuel Cells

Polymer electrolyte membranes are prepared from novel semi-interpenetrating polymer network material where the sulfonated poly (ether ether ketone) (SPEEK) is the linear polymer and the poly (ethylene glycol) diacrylate (PEGDA) is the cross-linking constituent. The semi-IPN is prepared by in situ polymerization of PEGDA in the presence of sulfonated poly (ether ether ketone). SPEEK is prepared by direct sulfonation of commercial PEEK (Gatone? 1100) by reported procedures. SPEEK with degree of sulfonation 63% (calculated from FT-NMR) is selected as the base membrane and different semi-IPN membranes were prepared by varying the PEGDA and SPEEK ratio. The degree of sulfonation of SPEEK and the formation of semi-IPN were confirmed by spectroscopy studies. The various semi-IPN membranes were characterized for ion-exchange capacity, water uptake, hydrolytic stability, proton conductivity and thermal stability for evaluating the suitability of these membranes for fuel cells. The proton conductivity of the membranes decreased with increasing PEGDA content. The Semi-IPN membranes exhibited conductivities (30°C) from 0.018 S/cm to 0.006 S/cm. These interpenetrating network membranes showed higher hydrolytic stability than the pure SPEEK membrane. This study shows that semi-IPN membranes based on PEGDA and SPEEK can be viable candidates for electrolyte membranes.     

磺化侧苯基杂萘联苯聚醚酮酮的合成与性能

以4-(3-苯基-4-羟基苯基)-2,3-二氮杂萘-1-酮(DHPZ-P)、 4-(4-羟基苯基)-2,3-二氮杂萘-1-酮(DHPZ)和1,4-二(4'-氟苯甲酰基)苯(BFBB)为原料, 经溶液亲核取代缩聚反应, 通过调节DHPZ-P和DHPZ的比例, 合成了一系列侧苯基杂萘联苯聚醚酮酮(PPEKK-P), 然后以浓硫酸为磺化剂, 制备出一系列磺化侧苯基杂萘联苯聚醚酮酮(SPPEKK-P). 利用傅里叶变换红外光谱(FTIR)和氢核磁共振谱(¹H NMR)对聚合物结构进行表征, 结果表明, 磺酸基团引入到聚合物链的侧苯基上. 采用溶液浇铸法制备SPPEKK-P质子交换膜. SPPEKK-P膜的吸水率、 溶胀率和质子传导率均随离子交换容量(IEC)的增加而增加, 且具有较好的耐氧化性. IEC最高的SPPEKK-P-100膜的质子传导率在95℃能达到7.44×10^-2 S/cm, 且甲醇渗透系数为5.57×10^-8 cm²/s, 阻醇性能优于Nafion117膜.     

含氨基磺化聚芳醚酮砜质子交换膜的制备与性能

通过四元缩聚的方法合成了带有氨基的磺化度可控的磺化聚芳醚酮砜共聚物(Am-SPAEKS). 采用红外光谱和核磁共振谱表征了Am-SPAEKS共聚物的结构. 该共聚物膜具有较好的热性能、尺寸稳定性、较高的质子传导率和阻醇能力. 在80℃时Am-SPAEKS-1膜的质子传导率达到0.0894 S/cm, 而其甲醇渗透系数在25℃时为0.24×10^-6 cm²/s, 低于相同温度下SPAEKS膜(0.87×10^-6 cm²/s)和Nafion膜(2×10^-6 cm²/s). 结果表明, Am-SPAEKS膜能够满足质子交换膜燃料电池(PEMFC)的使用要求.     

Sulfonated poly(ether ether ketone)/polyaniline composite proton-exchange membrane

Sulfonated poly(ether ether ketone) (PEEK) was prepared by sulfonation of commercial Victrex^@ PEEK and degree of sulfonation was found to be about 44.5% by ¹H NMR. Sulfonated PEEK/polyaniline composite membranes, in order to prevent methanol crossover, were prepared by chemical polymerization of a thin layer of polyaniline (PANI) in the presence of a high oxidant concentration on a single face modification. FTIR and PANI coating density studies confirmed the loading of PANI in sulfonated PEEK membrane matrix. PANI composite membranes with different polymerization time were prepared and subjected to thermogravimetric analysis as well as electrochemical and methanol permeability study to compare with sulfonated PEEK and Nafion 117 membrane. Ion-exchange capacity, water uptake, proton transport numbers and proton conductivities for different PANI composite sulfonated PEEK (SPEEK) membranes were found to be dependent on the coating density of the PANI in the membrane matrix and were slightly lower than that of Nafion 117 membrane. Methanol permeability of these membranes (especially SPEEK/PANI-1.5) was about four times lower than Nafion 117 membrane. Among the all SPEEK membranes synthesized in this study, SPEEK-1.5 appears to be more suitable for direct methanol fuel cell (DMFC) application considering optimum physicochemical and electrochemical properties, thermal stability as well as very low methanol permeability. Above all, the cost-effective and simple fabrication technique involved in the synthesis of such composite membranes makes their applicability quite attractive.     

Sulfonated poly(aryl ether ether ketone ketone)s containing fluorinated moieties as proton exchange membrane materials

A series of sulfonated poly(aryl ether ether ketone ketone)s statistical copolymers with high molecular weights were synthesized via an aromatic nucleophilic substitution polymerization. The sulfonation content (SC), defined as the number of sulfonic acid groups contained in an average repeat unit, could be controlled by the feed ratios of monomers. Flexible and strong membranes in sodium sulfonate form could be prepared by the solution casting method, and readily transformed to their proton forms by treating them in 2 N sulfuric acid. The polymers showed high T_gs, which increased with an increase in SC. Membranes prepared from the present sulfonated poly(ether ether ketone ketone) copolymers containing the hexafluoroisopropylidene moiety (SPEEKK‐6F) and copolymers containing the pendant 3,5‐ditrifluoromethylphenyl moiety (SPEEKK‐6FP) had lower water uptakes and lower swelling ratios in comparison with previously prepared copolymers containing 6F units. All of the polymers possessed proton conductivities higher than 1 × 10^?2 S/cm at room temperature, and proton conductivity values of several polymers were comparable to that of Nafion at high relative humidity. Their thermal stability, oxidative stability, and mechanical properties were also evaluated. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2299–2310, 2006     

Investigation of sulfonated poly(ether ether ketone sulfone)/heteropolyacid composite membranes for high temperature fuel cell applications

The sulfonated poly(ether ether ketone sulfone) (SPEEKS)/heteropolyacid (HPA) composite membranes with different HPA content in SPEEKS copolymers matrix with different degree of sulfonation (DS) were investigated for high temperature proton exchange membrane fuel cells. Composite membranes were characterized by Fourier transfer infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). FTIR band shifts suggested that the sulfonic acid groups on the copolymer backbone strongly interact with HPA particles. SEM pictures showed that the HPA particles were uniformly distributed throughout the SPEEKS membranes matrix and particle sizes decreased with the increment of copolymers' DS. The holes were not found in SPEEKS‐4/HPA30 (consisting of 70% SPEEKS copolymers with DS = 0.8 and 30% HPA) composite membrane after composite membranes were treated with boiling water for 24 h. Thermal stabilities of the composite membranes were better than those of pure sulfonated copolymers membranes. Although the composite membranes possessed lower water uptake, it exhibited higher proton conductivity for SPEEKS‐4/HPA30 especially at high temperature (above 100 °C). Its proton conductivity linearly increased from 0.068 S/cm at 25 °C to 0.095 S/cm at 120 °C, which was higher than 0.06 S/cm of Nafion 117. In contrast, proton conductivity of pure SPEEKS‐4 membrane only increased from 0.062 S/cm at 25 °C to 0.078 S/cm at 80 °C. At 120 °C, proton conductivity decreased to poor 0.073 S/cm. The result indicated that composite membranes exhibited high proton conductivity at high temperature. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1967–1978, 2006     

Oxidatively stable and highly proton conductive membrane from poly(arylene ether)s containing biphenyl moiety as pendent groups

Novel poly(arylene ether)s with sulfonic acid groups attached onto pendent biphenyl rings were successfully synthesized by the nucleophilic displacement of aromatic dihalides with bisphenols in aprotic solvent in the present of excess potassium carbonate, followed by sulfonation with chlorosulfonic acid. The sulfonation took place only on the pendent biphenyl rings due to the specially designed molecular structure. The sulfonated polymers were very soluble in common organic solvents, such as dimethyl sulfoxide, N,N′-dimethylacetamide, dimethylformamide, and can be readily cast into tough and smooth films. These membranes showed excellent stabilities resistance to both oxidation and hydrolysis, as evidenced by subjecting to both Fenton's reagent test and immersion in boiling water. The proton conductivities (3.2 × 10⁻³ S cm⁻¹) of the as-made membranes were higher than that of Nafion^® 117 (1.9 × 10⁻³ S cm⁻¹) under same conditions. The satisfied properties of these new polymers demonstrated them as promising candidates for proton exchange membrane in PEM fuel cell applications.     

全钒液流电池用磺化聚醚醚酮/锂皂石质子膜的结构及性能

通过溶液流延法制备了磺化聚醚醚酮/锂皂石(SPEEK/Lap)复合膜, 对其物理化学性质、 机械性能、 化学稳定性及单电池性能进行了测试. 在SPEEK基质中引入的Lap有效改善了复合膜的质子传导率、 溶胀率和机械性能. 当Lap添加量(质量分数)从0.2%增到1.5%时, 复合膜的质子传导率随之增加(19.9~23.6 mS/cm). SPEEK/Lap-0.2复合膜的自放电时间为57.2 h, 是Nafion 117膜的2.4倍和纯SPEEK膜的1.5倍. 在80 mA/cm ²电流密度下, SPEEK/Lap-0.2复合膜的电压效率(VE, 86.5%)和能量效率(EE, 84.0%)明显高于Nafion 117膜(VE: 83.8%, EE: 80.7%)和纯SPEEK膜(VE: 81.4%, EE: 78.9%). 同时, SPEEK/Lap-0.2复合膜经100次充放电循环测试后具有良好的循环稳定性和结构稳定性.     

不同磺化度下的磺化聚醚醚酮对全钒储能液流电池性质影响的研究

本文报道了采用浓硫酸作为磺化剂,成功合成了不同磺化度下的聚醚醚酮(PEEK)膜,并深入研究了磺化条件包括磺化时间和磺化剂的用量对所获薄膜性能的影响,获得了在不同磺化度（DS）下SPPEK膜的离子交换容,含水率,机械性能,质子电导率等参数,特别测定了在全钒液流电池工作条件下钒离子(Ⅳ)渗透率,首次为该类液流储能电池使用价廉质优的质子交换膜提供了基础实验数据。室温条件下的实验结果如下：1）磺化12小时后,膜的磺化度46%,含水量为28%,钒离子(Ⅳ)选择性最佳（钒离子渗透率为1.2×10-7 cm2/min-1,是Nafion117 (2.9×10-6 cm2/min-1)的1/24）,其质子电导率只有0.02 S/cm;2）磺化96小时其磺化度达79%的膜,质子电导率达0.16 S/cm,是Nafion117 (0.10S/cm) 的1.6倍, 但其机械性能最差;3）与Nafion117膜相比,磺化在36到48小时的SPPEK膜其机械力学性能好,薄膜的钒离子渗透率、离子交换容IEC、质子导电率和含水率高,且对钒离子的选择性佳,尤其价格仅为Nafion膜的1/13,是理想的Nafion膜的代替物,可望直接应用于全钒氧化还原液流（VRB）电池中。本文还讨论了磺化时间和不同磺化剂量对膜的性质的影响。     

可逆加成-断裂链转移自由基聚合法合成梳型磺化聚醚醚酮

以带双硫酯取代基聚醚醚酮为大分子链转移剂, 采用可逆加成-断裂链转移自由基聚合(RAFT)法合成不同接枝率的磺化聚醚醚酮(g-SPEEK), 并对其结构进行表征. 在单体/链转移剂/引发剂的投料比(摩尔比)为50:4:1, 温度为70 ℃, 反应24 h, 得到聚合物膜的离子交换容量和吸水率分别为1.312 mmol/g和43.51%, 其溶胀率为5.05%, 低于Nafion膜的11.50%. 热重分析(TGA)结果表明该梳型g-SPEEK具有较好的热力学稳定性, 且该聚合物膜具有与Nafion膜相当的抗氧化性. 在相同的离子交换容量下, 梳型g-SPEEK比主链型SPEEK具有更好的H⁺离子透过性能.     

磺化聚芳醚酮砜/聚芳醚砜噁二唑复合型质子交换膜的制备与性能

为了降低质子交换膜(PEM)的甲醇渗透系数和改善PEM在中高温(80~120 ℃)时的质子传导率, 以自制的磺化度(SD)为100%的磺化聚芳醚酮砜(SPAEKS)与聚芳醚砜噁二唑(PAESO)为原料, 采用溶液共混法制备了SPAEKS/PAESO复合膜, 并用傅里叶变换红外光谱(FTIR)和热重分析(TGA)对其进行了表征. 结果表明, 该复合膜具有较好的化学稳定性和热稳定性. 扫描电子显微镜(SEM)照片显示, 复合膜具有较好的致密结构, 其甲醇渗透系数为3.9×10^-7~6.6×10^-7 cm²/s, 低于SPAEKS的8.7×10^-7 cm²/s. 在100 ℃时复合膜的质子传导率达到0.074 S/cm, 高于SPAEKS膜的0.066 S/cm.     

自交联型磺化聚醚醚酮质子交换膜的合成

以含3,3'-二烯丙基双酚 A 结构单元的聚醚醚酮为基膜材料, 通过自由基加成反应在取代基上引入磺酸基团, 合成侧链型磺化聚醚醚酮(SPEEK)质子交换膜. 用傅里叶变换红外(FTIR)光谱、 核磁共振氢谱(¹H NMR)、 热重分析(TG)和扫描电子显微镜(SEM)等方法对 SPEEK 的结构进行表征. 实验结果表明, 巯基丙磺酸被接枝在聚醚醚酮侧基上, SPEEK 膜具有明显的亲水疏水微相分离形貌, 磺酸基团相互聚集形成离子通道. SPEEK 膜离子交换容量为 2.12 mmol/g, 钒离子渗透率为 1.54×10^-6 cm²/min, 低于Nafion117 膜的钒离子渗透率, 阻钒能力优于 Nafion117 膜. 以 SPEEK-4 膜组装电池的自放电时间约为130 h, 长于 Nafion117 膜的 66 h. 电池充放电循环 50 次, SPEEK-4 膜的库仑效率、 电压效率和能量效率没有明显降低, 显示出良好的稳定性.     

磺化双酚芴型聚醚醚酮质子交换膜的制备及其在钒流电池中的应用

以双酚芴为结构单元合成双酚型聚醚醚酮聚合物,聚醚醚酮经浓硫酸磺化在双酚芴结构单元中引入磺化基团制备出聚醚醚酮质子交换膜(SF-PEEK)。 用傅里叶变换红外光谱(FTIR)、核磁共振氢谱(¹H NMR)、热重分析(TG)、原子力显微镜(AFM)和扫描电子显微镜(SEM)等方法对聚醚醚酮质子交换膜的结构进行表征。 结果表明,磺酸基团被成功地在聚醚醚酮侧基上,SF-PEEK膜具有明显的亲水疏水微相分离形貌,磺酸基团相互聚集成形成离子通道。 SF-PEEK膜离子交换容量(IEC)达到1.97 mmol/g时,其电导率达到4.15×10^-2 S/cm,略低于Nafion117膜的5.67×10^-2 S/cm,但其钒离子渗透率仅为Nafion117膜的20.1%,表现出极好的离子选择性。 在钒流电池测试中,SF-PEEK膜在不同电流密度下库伦效率均高于Nafion117膜,其中IEC为1.97 mmol/g的SF80-PEEK608(80为SF的物质的量分数,608为60 ℃反应8 h)库伦效率在电流密度为40 mA/cm²时达到最大值80.9%,高于Nafion117膜的78.8%。 在自放电测试中,以SF80-PEEK608膜组装的电池的自放电时间为90 h,高于Nafion117膜的57 h。     

SYNTHESIS AND PROPERTIES OF SULFONATED POLY(ETHER KETONE)S CONTAINING 3,5-DIMETHYL PHTHALAZINONE MOIETIES AS PROTON EXCHANGE MEMBRANE MATERIALS

Sulfonated poly（ether ketone）s containing 3,5-dimethyl phthalazinone moieties（SPPEK-DMs）with different degrees of sulfonation（DS）were synthesized via direct polycondensation from 4-（3,5-dimethyl-4-hydroxyphenyl）-2,3- phthalazinone,4,4’-difluorobenzophenone and 3,3’-disulfonate-4,4’-difluorobenzophenone.The chemical structure of SPPEK-DMs was characterized by FTIR and ¹H-NMR.Thermal stability of SPPEK-DMs was characterized by the thermogravimetric analysis.The membranes prepared from SPPEK-DMs exhibited ion exchange capacities（IEC）ranging from 0.93 mmol·g^-1to 1.86 mmol·g^-1.Water uptake,swelling,oxidative stability and methanol permeability of SPPEKDMs membranes were investigated.SPPEK-DMs membranes exhibited high oxidative stability.The methanol permeability values of SPPEK-DMs membranes were in the ranee 5.15×10^-8-6.61×10^-7cm s,which was much lower than those of Nafionl 17.The proton conductivity of SPPEK-DM40 membranes was 1.1×10^-2Scm^-1at 70℃.     

Morphology control of sulfonated poly(ether ketone ketone) poly(ether imide) blends and their use in proton-exchange membranes

Polymer blends based on sulfonated poly(ether ketone ketone) (SPEKK) as the proton-conducting component and poly(ether imide) (PEI) as the second component were considered for proton-exchange membranes (PEMs). The PEI was added to improve the mechanical stability and lower the water swelling in the fuel cell environment. Membranes were cast from solution using N-methyl-2-pyrrolidone (NMP) and dimethylacetamide (DMAc). The ternary, polymer/polymer/solvent, phase diagram was determined to provide guidance on how to control the morphology during solvent casting of blend membranes.

For blends of SPEKK (ion-exchange capacity = 2 mequiv/g) with PEI as the minority component, the morphology consisted of dispersed particles of 0.5–6 μm. Larger particles were achieved by increasing the PEI content and/or lowering the casting temperature. High-temperature annealing after solution casting did not affect the morphology of blend membranes, due to the low mobility and compatibility of the two polymers.

The possible use of SPEKK/PEI blends in PEMs is discussed in terms of existing theories of ion transport in polymers.     

A novel proton-conductive membrane with reduced methanol permeability prepared from bromomethylated poly(2,6-dimethyl-1,4-phenylene oxide) (BPPO)

A series of proton-conducting membranes were developed for direct methanol fuel cell (DMFC) applications via sulfonation of bromomethylated poly(2,6-dimethyl-1,4-phenylene oxide) (BPPO) base membranes. Besides the low manufacture cost, the membranes exhibited an excellent control on methanol crossover and swelling, and a sound balance with high proton conductivities. These can be attributed to the inherent properties of membrane structures: (i) benzyl substitution with bromine, which imparted the membrane stronger hydrophobicity, (ii) cross-linking between BPPO chains, which enhances the dimensional stability and renders the membrane a dense texture, (iii) proper content of sulfonic acid groups, which guarantees the proton conductivity. An optimal membrane was obtained after investigating the effects of the bromination degree and sulfonation process on the performances of corresponding membranes, i.e., the membrane possesses the methanol permeability of 2.64 × 10⁻⁸ cm²/s and characteristic factor Φ value of 30 times higher than that of Nafion^® 117. The sulfonation process should be controlled within a proper period of time and in mild sulfonation conditions so as to achieve a proton conductivity higher than 0.07 S/cm for potential applications in DMFC.     

Evolution of Morphology and Properties of Sulfonated Poly（ether ether ketone ketone） Membranes Fabricated via Electrospinning

Sulfonated poly(ether ether ketone ketone)(SPEEKK) membranes with different degrees of sulfonation(DS) were successfully prepared via electrospinning method. The morphology of the resulted membranes varies from nanospheres to nanofibers with increasing the concentration of SPEEKK. The conductivities of the membranes prepared under the same condition increase with the DS increasing. The spherical morphological membranes with a DS of 1.2 show the highest proton conductivity, 0.55 S/cm, which is much higher th...     

磺化聚醚醚酮膜的制备及其阻醇和质子导电性能

直接甲醇燃料电池 (Ｄｉｒｅｃｔｍｅｔｈａｎｏｌｆｕｅｌｃｅｌｌ,ＤＭＦＣ)以高效、清洁和燃料储运方便等优点适宜于作为各种用途的可移动动力源 ,成为 2 0世纪 90年代以来研究与开发的热点[1,2 ] .目前 ,这种电池的研究难点主要集中在催化剂不稳定和质子交换膜透醇上 .一张好的ＤＭＦＣ膜不但要可传递质子、绝缘电子 ,还应具有良好的阻醇性能 .如果膜的阻醇性能不好 ,甲醇会穿过膜到达阴极 ,与氧直接反应而不产生电流 ,不但造成燃料的浪费 ,同时也影响阴极的正常反应 ,使电池效率下降[3] .目前广泛应用于燃料电池中的Ｎａｆｉｏｎ系列膜…