ZnO/C纳米球的亚甲基蓝单吸附特性:平衡、动力学及机理（英文）

采用电弧放电法制备了Zn O/C纳米球,利用FESEM、XRD和N2吸附/脱附测试进行了表征。在避光条件下研究了复合材料对亚甲基蓝的吸附性能。研究结果表明,随着亚甲基蓝的浓度及接触时间的增长吸附量明显上升,在吸附时间为150 min时达到吸附平衡。采用Langmuir、Freundlich及Temkin等温吸附模式对吸附平衡进行了研究。结果表明,吸附等温线符合Langmuir等温吸附模式,单层吸附饱和容量可达188.68 mg·g-1。利用动力学模型、内扩散模型和外扩散速率控制模型拟合实验数据,拟合数据表明其动力学符合伪二级动力学模型;内扩散机理不是吸附速率的唯一限制机理,亚甲基蓝的总吸附速率受膜扩散控制。     

氨基酸螯合吸附树脂对苯酚的吸附行为研究

合成了一种L-酪氨酸修饰的螯合吸附树脂(AJS-02),并与超高交联树脂NDA-150作对比,研究了其对苯酚的吸附和脱附行为.静态实验结果表明,在研究的浓度范围内,吸附平衡数据符合Langmuir等温吸附方程且吸附为放热过程.溶液的初始浓度为100 mg/L、吸附温度为288 K时,苯酚在AJS-02和NDA-150上的平衡吸附量分别为76.98和91.97 mg/g,苯酚在两种树脂上的吸附是比表面积和表面官能团共同作用的结果.动力学数据表明吸附动力学符合液膜扩散方程和颗粒内扩散方程,液膜扩散为吸附速率的主要控制步骤.动态吸附-脱附实验表明,AJS-02树脂对苯酚的动态穿透吸附量和饱和吸附量分别为5.26×10-2和6.60×10-2mmol/mL,采用95%乙醇作脱附剂,脱附率可达91.5%以上.     

ZnO/C纳米球的亚甲基蓝单吸附特性:平衡、动力学及机理

采用电弧放电法制备了ZnO/C纳米球,利用FESEM、XRD和N₂吸附/脱附测试进行了表征。在避光条件下研究了复合材料对亚甲基蓝的吸附性能。研究结果表明,随着亚甲基蓝的浓度及接触时间的增长吸附量明显上升,在吸附时间为150 min时达到吸附平衡。采用Langmuir、Freundlich及Temkin等温吸附模式对吸附平衡进行了研究。结果表明,吸附等温线符合Langmuir等温吸附模式,单层吸附饱和容量可达188.68 mg·g^-1。利用动力学模型、内扩散模型和外扩散速率控制模型拟合实验数据,拟合数据表明其动力学符合伪二级动力学模型;内扩散机理不是吸附速率的唯一限制机理,亚甲基蓝的总吸附速率受膜扩散控制。     

ZnO/C纳米球的亚甲基蓝单吸附特性:平衡、动力学及机理

采用电弧放电法制备了ZnO/C纳米球,利用FESEM、XRD和N₂吸附/脱附测试进行了表征。在避光条件下研究了复合材料对亚甲基蓝的吸附性能。研究结果表明,随着亚甲基蓝的浓度及接触时间的增长吸附量明显上升,在吸附时间为150 min时达到吸附平衡。采用Langmuir、Freundlich及Temkin等温吸附模式对吸附平衡进行了研究。结果表明,吸附等温线符合Langmuir等温吸附模式,单层吸附饱和容量可达188.68 mg·g^-1。利用动力学模型、内扩散模型和外扩散速率控制模型拟合实验数据,拟合数据表明其动力学符合伪二级动力学模型;内扩散机理不是吸附速率的唯一限制机理,亚甲基蓝的总吸附速率受膜扩散控制。     

起泡剂C12E8的表面流变学性质

利用表面波技术研究起泡剂C_(12)E_8的表面流变学性质以及解释表面变形所产生的表面张力梯度的修复机理．实验结果表明，起泡剂C_(12)E_8的表面具有粘弹性质，其减胀模量与表面变形频率有关系．在低浓度时，随着溶液浓度的增加，表面吸附量的增加很高了膨胀模量．而在高浓度时，由于表面与溶液之间的扩散交换抵消了膨胀模量的增加，这导致膨胀模量随着溶液浓度增加反而降低．     

Gemini表面活性剂C12-2-C12·2Br在气-液界面吸附动力学

用最大泡压法考察Gemini表面活性剂C12-2-C12·2Br在气-液界面吸附动力学。研究表明,随着表面活性剂浓度的增加,表面活性剂分子的扩散速率加快,其扩散系数D随之增大。与对应的单体表面活性剂DTAB比较,由于2种表面活性剂的结构差别引起C12-2-C12·2Br的疏水性比DTAB的强,导致前者的吸附扩散系数D比后者的大将近100倍。表面活性剂在气液界面吸附后期,属于扩散-动力学控制模型,有吸附能垒Ea存在,C12-2-C12·2Br与DTAB的吸附能垒分别为17．29和9、13kJ／mol。由于C12-2-C12·2Br在气液界面上的表面压和表面覆盖率以及分子的头基面积都大于DTAB,引起了前者在气液界面上的吸附能垒增大。     

用分子轨道理论研究NO气体在TiO2表面吸附

根据一氧化氮(NO)气体在二氧化钛(TiO)表面吸附和脱附的实验结果,揭示了气体脱附量的变化规律．利用MOPAC和GAUSSIAN分子轨道理论计算了在TiO2(110)表面上吸附NO分子的原子簇模型,电荷分布以及原子簇的能级,推断了NO在TiO(110)表面吸附的稳定性．     

氧在银／二氧化硅催化剂上的超高真空程序升温脱附

 研究了氧在Ag／SiO2催化剂上的超高真空程序升温脱附．结果表明，脱附谱中出现了对应于表面分子氧（Tp＝340K）、体相氧（Tp＝570K）和次表层氧（Tp＝700～800K）的脱附峰．由于催化剂在制备过程中经过高温焙烧，因而其表面原子氧浓度低，脱附谱中未出现原子氧的脱附峰．高温焙烧还可使表面缺陷浓度增大，有利于原子氧向体相扩散，形成体相溶解氧，也有利于体相氧向表面扩散，所以对应于体相氧的570K脱附峰较强．体相氧和次表层氧向表面的扩散遵循不同的扩散机理．     

气相存在下过渡金属表面脱附动力学机理的研究

作者利用同位素跳跃技术来探讨气相压强促进过渡金属表面吸附分子脱附这一新现象的机理。获得了３５３Ｋ下饱和吸附Ｃ１６Ｏ的Ｒｅ（０００１）表面的超高真空等温脱附和不同气相压强的同位素Ｃ１８Ｏ交换的谱图。从相对覆盖度及其对数随时间的变化曲线可以看出,真空等温脱附过程为一级动力学过程。而在气相同位素存在下交换脱附过程可用一级加二级来近似,拟合的结果与实验符合很好。作者还发现了交换速率远大于真空等温脱附速率,而且随压强的增加而增加,这说明气相压强直接促进了表面吸附分子的脱附。并提出了协同吸附－脱附机理来解释这一新现象     

Pt电极上CO的同位素取代吸附机理研究

本文依据偶极耦合理论和相干势近似方法,合理选择粗糙电极上吸附分子的频率分布函数、一氧化碳(CO)吸附层的结构参数以及偶极耦合作用常数,对13CO/12CO同位素取代过程记录的红外光谱进行了拟合.研究发现,只有在拟合过程中引入低频CO分子优先取代,就可成功地模拟整个同位素取代过程的红外光谱随表面吸附的13CO/12CO组分的变化,并由此提出了吸附驱动的脱附机理,COad的脱附不是热激发脱附,而是吸附到表面的CO分子为其邻近位置COad的脱附提供能量.伸缩振动频率较低的COad处于台阶或缺陷位等较开阔的位置(尽管其吸附能较高),周围有较大的空间,利于来自溶液的CO分子的吸附,因此在台阶或缺陷位优先发生同位素的取代.     

表面波技术研究TBP对C12E8表面流变性质的影响

The influence of antifoaming agent TBP on the surface adsorption and on the surface rheological properties of foaming agent C12E8 is investigated by the damped longitudinal wave method, and the antifoaming mechanism of the antifoaming agent TBP on C12E8 is explored in this paper. The experimental results show that while the concentration of foaming agent C12E8 is smaller than cmc and at ω=6.28 rad•s-1, the decreases of surface dilational modulus, surface dilational elasticity, surface dilational viscosity and the increases of the phase angle when the concentration of TBP increase for the C12E8+TBP aqueous solution (C12E8=0.074 mmol•L-1) have been related to the diffusional exchange between surface and bulk and to the Marangoni effect, which depends on the restored mechanism of surface tension gradient due to the stretched surface. This has been related to the mechanism of antifoaming action.     

不同电性Gemini表面活性剂界面扩张性质

利用Langmuir槽法研究了含聚氧乙烯醚链中间链的两性Gemini表面活性剂C8E4NC12、阳离子Gemini表面活性剂C12NE3NC12和阴离子Gemini表面活性剂C8E4C8在空气/水表面和癸烷/水界面上的扩张性质,考察浓度对3种Gemini表面活性剂溶液表、界面扩张性质的影响.结果表明,由于分子间存在库仑引力,两性Gemini分子表现出较高的扩张弹性和粘性,且界面扩张性质类似于表面.对于有相同电荷Gemini分子,C8E4C8分子中的刚性苯环导致其疏水长链在表面上的取向不同于C12NE3NC12分子,两者表现出不同的表面扩张性质;而油分子能改变同电荷Gemini分子中长链烷基的取向,造成其界面扩张弹性和粘性远低于表面.提出了不同电性Gemini分子在界面排布的示意图,并利用弛豫过程的特征参数进行了验证.     

不同结构芳香侧链酰基牛磺酸钠的表面扩张性质

利用悬挂滴方法研究了N-(α-苯氧基)十四酸牛磺酸钠(12+B-T)和N-(α-对乙基苯氧基)十四酸牛磺酸钠(12+2B-T)在空气/水表面上的动态扩张粘弹性质, 考察了时间、扩张频率及摩尔浓度对扩张模量和相角的影响, 测定了不同摩尔浓度条件下的泡沫性能. 研究发现: 低浓度条件下, 表面分子间相互作用决定表面活性剂吸附膜的性质, 膜以弹性为主; 高浓度条件下, 扩散交换过程起主导作用, 吸附膜表现出粘弹特性. 表面活性剂芳环支链上增加一个乙基, 分子间相互作用增强, 扩张模量增大, 泡沫更加稳定.     

聚氧乙烯醚类表面活性剂表面扩张粘弹性质研究

研究了非离子表面活性剂壬基苯酚聚氧乙烯醚NP-8, NP-10和NP-12水溶液的表面扩张粘弹性质, 考察了氧乙烯数的变化对表面吸附膜特性的影响. 研究结果表明, 三种表面活性剂的扩张弹性随着工作频率的增大而增大, 扩张粘性则在0.1~0.01 Hz范围内通过不明显的极大值; 扩张弹性和粘性随着浓度的增加在同一浓度处通过一个极大值; 氧乙烯数从8增加到12, 表面扩张弹性、粘性和相角的变化不大. 从发生在表面上和表面附近的微观弛豫过程的角度对实验结果进行了讨论.     

Effect of alkyl chain length on the surface dilational rheological and foam properties of N-acyltaurate amphiphiles

The dynamic dilational properties of sodium 2-(2-(alkylaryloxy)-alkylamido)ethanesulfonates (12+nB-Ts) at the air–water interfaces were investigated by drop shape analysis, and their foam properties were also measured. The influences of time and bulk concentration on surface dilational properties were expounded. The results show that the molecular interaction controls the nature of adsorption film during lower concentration range, and the film behaves elastic in nature. During higher concentration range, the diffusion exchange process controls the dynamic dilational properties and the surface film shows remarkable viscoelasticity. An increase in hydrophobic chain length enhances the molecular interaction at low concentration and speeds up the diffusion exchange process at high concentration, which results in the different variations of modulus at different concentration regions. For 12+nB-Ts, too short a chain probably produces bad film elasticity, whereas too great a length produces too fast liquid drainage. Therefore the optimal length in the branched chain leads to the best foam stability.     

Interfacial dilational rheological property and lamella stability of branched alkyl benzene sulfonates solutions

The dynamic dilational properties of branched alkyl benzene sulfonates at the air–water and decane–water interfaces were investigated by drop shape analysis, and their lamella stability was measured. The influences of time, dilational frequency, and bulk concentration on surface dilational elasticity and dilational viscosity were expounded. The results show that the molecular interaction controls the nature of adsorption film during lower concentration range and the film behaves elastic in nature. During higher concentration range, the diffusion-exchange process controls the dynamic dilational properties and the surface film shows remarkable viscoelasticity. An increase in hydrophobic chain length enhances the molecular interaction, which results in the increase of dilational parameters and lamella stability. The data correlation suggests that the ability to form a stable lamella is linked to the intrinsic surface dilational elasticity.     

New methodology to determine the rate-limiting adsorption kinetics mechanism from experimental dynamic surface tension data

We present a new methodology to determine the rate-limiting adsorption kinetics mechanism (diffusion-controlled vs mixed diffusion-barrier controlled), including deducing the kinetics parameters (the diffusion coefficient, D, and the energy-barrier parameter, beta), from the experimental short-time dynamic surface tension (DST) data. The new methodology has the following advantages over the existing procedure used to analyze the experimental DST data: (a) it does not require using a model for the equilibrium adsorption isotherm, and (b) it only requires using the experimental short-time DST data measured at two initial surfactant bulk solution concentrations. We apply the new methodology to analyze the experimental short-time DST data of the following alkyl poly(ethylene oxide), CiEj, nonionic surfactants: C12E4, C12E6, C12E8, and C10E8 measured using the pendant-bubble apparatus. We find that for C12E4 and C12E6, the effect of the energy barrier on the overall rate of surfactant adsorption can be neglected for surfactant bulk solution concentrations below their respective critical micelle concentrations (CMCs), and therefore, that the rate-limiting adsorption kinetics mechanism for C12E4 and C12E6 is diffusion-controlled at any of their premicellar surfactant bulk solution concentrations. On the other hand, for C12E8 and C10E8, we find that their respective CMC values are large enough to observe a significant effect of the energy barrier on the overall rate of surfactant adsorption. In other words, for C12E8 and C10E8, the rate-limiting adsorption kinetics mechanism shifts from diffusion-controlled to mixed diffusion-barrier controlled as their premicellar surfactant bulk solution concentrations increase. We test the new methodology by predicting the short-time DST profiles at other initial surfactant bulk solution concentrations, and then comparing the predicted DST profiles with those measured experimentally. Very good agreement is obtained for the four CiEj nonionic surfactants considered. We also compare the results of implementing the new methodology with those of implementing the existing procedure, and conclude that using a model for the equilibrium adsorption isotherm can lead not only to different values of D and beta, but it can also lead to a completely different determination of the rate-limiting adsorption kinetics mechanism. Since the new methodology proposed here does not require using a model for the equilibrium adsorption isotherm, we conclude that it should provide a more reliable determination of the rate-limiting adsorption kinetics mechanism, including the deduced kinetics parameters, D and beta.     

疏水基支链化对甜菜碱表面扩张流变性质的影响

利用悬挂滴方法研究了同分异构的直链（C₁₆PB）和支链（C₁₆GPB）十六烷基羟丙基羧酸甜菜碱的表面扩张流变性质,考察了时间、表面压、工作频率及体相浓度对扩张模量和相角的影响.研究发现,羟丙基甜菜碱分子在溶液表面上吸附时,整个亲水基团倾向于平铺在表面上,造成较高的表面扩张模量,表面膜性质由亲水基团取向变化等膜内过程控制.甜菜碱分子疏水烷基的支链化造成分子间相互作用增强,不仅能增大模量,而且在高浓度条件下出现动态模量的最大值现象,说明表面膜的强度与分子排布密切相关,并非单纯由表面分子浓度决定.     

Stability of foam films and surface rheology: an oscillating bubble study at low frequencies

The dilational surface elasticity epsilon and the dilational surface viscosity eta of the two nonionic surfactants n-dodecyl-beta-d-maltoside (beta-C12G2) and tetraethyleneglycol-monodecyl ether (C10E4) were studied using the oscillating drop method. The experiments were carried out at different concentrations and frequencies with an accessible frequency range of 0.005-0.2 Hz. The results are discussed in the light of previous disjoining pressure measurements that demonstrated that the stability of thin liquid films cannot be explained solely by the magnitude of the surface forces. Indeed, a comparison of the results obtained for beta-C12G2 with those obtained for C10E4 reveals a correlation between the stability of the films and the surface dilational elasticity of the respective monolayers.