生物油酸性组分分离精制研究

生物油因水分含量高和呈酸性未能作为高品位能源直接规模化应用。利用分子蒸馏技术将生物油水分与酸性组分作为整体对象进行分离,既得到生物油酸性组分富集馏分,又获得了水分含量低、酸性较弱与热值较高的精制生物油Ⅰ（蒸馏重质馏分）与精制生物油Ⅱ（常温冷凝馏分）。同时,具体考察了精制前后生物油的pH值、热值和水分等参数的变化规律。研究表明,生物油的水分与酸性组分得到有效分离,精制生物油Ⅰ和Ⅱ的低级羧酸含量从原始生物油的18.85%分别降低至0.96%和2.2%     

Nanoorganization and Phase Behavior of Mixtures of Nicotinic Acid with Dodecylbenzenesulfonic Acid

Abstract

Mesomorphically ordered structures and phase behavior of the mixtures of nicotinic acid (NICA) and dodecylbenzenesulfonic acid (DBSA) were investigated by X‐ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and polarized optical microscopy (POM). The POM observations revealed that the NICA–DBSA mixtures spontaneously formed liquid crystalline phases, although both NICA and DBSA were not liquid crystalline molecules. The NICA–DBSA mixtures formed ordered lamellar structures in DBSA‐rich mixtures and hexagonal cylinder structure in NICA‐rich mixtures. The mesomorphically ordered structures and optical anisotropy were caused by hierarchical interactions in the NICA–DBSA mixtures. The phase diagram divided into five regions—optically isotropic disordered phase, optically isotropic lamellar phase, optically anisotropic lamellar phase, optically anisotropic cylinder phase, and crystalline solid phase—is drawn by summarizing the XRD and POM results.     

Further Investigation into the Stability of Water-in-Crude Oil Emulsions Formed in Burgan Oilfield: Effect of Toluene,Resins to Asphaltenes Ratio,and Surfactant

Factors controlling the formation and stabilization of water-in-crude oil (w/o) emulsions in oil fields are of great concern to the petroleum industry for the economic development of underground oil reservoirs. Controlling and minimizing the formation of w/o emulsions and demulsification of water from emulsions are also important for environmental development. Because of its importance, the mechanisms, formation, and stability of w/o emulsions have received considerable attention. This article deals with some of the factors responsible for the formation and stabilization of w/o emulsions formed in Burgan oil field in Kuwait. Some of the factors investigated in this study are the naturally occurred surface active components of crude oils such as asphaltenes and resins. Stability of emulsion samples with resins to asphaltenes ratio (R/A) contents of 3, 5, 9, 12, and 20 has been studied. It was found that Emulsion tightness is correlated with resins to asphaltene content of the sample. As the R/content increases the emulsion becomes unstable. The effect of additives such as toluene and dodecyle benzene sulfonic acid (DBSA) on the stability of various emulsion samples collected from oil field are also reported. A 2 wt% of DBSA was found to resolve all the water from emulsion samples collected from Burgan oilfield.     

Electrically conductive,melt‐processed ternary blends of polyaniline/dodecylbenzene sulfonic acid,ethylene/vinyl acetate,and low‐density polyethylene

Although polyaniline (PANI) has high conductivity and relatively good environmental and thermal stability and is easily synthesized, the intractability of this intrinsically conducting polymer with a melting procedure prevents extensive applications. This work was designed to process PANI with a melting blend method with current thermoplastic polymers. PANI in an emeraldine base form was plasticized and doped with dodecylbenzene sulfonic acid (DBSA) to prepare a conductive complex (PANI–DBSA). PANI–DBSA, low‐density polyethylene (LDPE), and an ethylene/vinyl acetate copolymer (EVA) were blended in a twin‐rotor mixer. The blending procedure was monitored, including the changes in the temperature, torque moment, and work. As expected, the conductivity of ternary PANI–DBSA/LDPE/EVA was higher by one order of magnitude than that of binary PANI–DBSA/LDPE, and this was attributed to the PANI–DBSA phase being preferentially located in the EVA phase. An investigation of the morphology of the polymer blends with high‐resolution optical microscopy indicated that PANI–DBSA formed a conducting network at a high concentration of PANI–DBSA. The thermal and crystalline properties of the polymer blends were measured with differential scanning calorimetry. The mechanical properties were also measured. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3750–3758, 2004     

Simple, reversible emulsion system switched by pH on the basis of chitosan without any hydrophobic modification

Chitosan without hydrophobic modification is not a good emulsifier itself. However, it has a pH-tunable sol-gel transition due to free amino groups along its backbone. In the present work, a simple reversible Pickering emulsion system based on the pH-tunable sol-gel transition of chitosan was developed. At pH > 6.0, as adjusted by NaOH, chitosan was insoluble in water. Chitosan nanoparticles or micrometer-sized floccular precipitates were formed in situ. These chitosan aggregates could adsorb at the interface of oil and water to stabilize the o/w emulsions, so-called Pickering emulsions. At pH < 6.0, as adjusted by HCl, chitosan was soluble in water. Demulsification happened. Four organic solvents (liquid paraffin, n-hexane, toluene, and dichloromethane) were chosen as the oil phase. Reversible emulsions were formed for all four oils. Chitosan-based Pickering emulsions could undergo five cycles of emulsification-demulsification with only a slight increase in the emulsion droplet size. They also had good long-term stability for more than 2 months. Herein, we give an example of chitosan without any hydrophobic modification to act as an effective emulsifier for various oil-water systems. From the results, we have determined that natural polymers with a stimulus-responsive sol-gel transition should be a good particulate emulsifier. The method for in situ formation of pH-responsive Pickering emulsions based on chitosan will open up a new route to the preparation of a wide range of reversible emulsions.     

Polyurethane/polyaniline and polyurethane‐poly(methyl methacrylate)/polyaniline conductive core‐shell particles: Preparation,morphology, and conductivity

Polyurethane/polyaniline (PU/PANI) and polyurethane‐poly(methyl methacrylate)/polyaniline (PU‐PMMA/PANI) conductive core‐shell particles were synthesized by a two‐stage polymerization process. The first stage was to produce a core of PU or PU‐PMMA via miniemulsion polymerization using sodium dodecyl sulfate (SDS) as the surfactant. The second stage was to synthesize the shell of polyaniline over the surface of core particles. Hydrogen chloride (HCl) and dodecyl benzenesulfonic acid (DBSA) were used as the dopant agents. Ammonium persulfate (APS) was used as the oxidant for the polymerization of ANI. Different concentrations of HCl, DBSA, and SDS would cause different conformations of PANI chains and thus different morphologies of PANI particles. UV–visible spectra revealed that the polaron band was blue‐shifted because of the more coiled conformation of PANI chains by increasing the concentration of DBSA. Besides, with a high concentration of DBSA, both spherical‐ and rod‐shape PANI particles were observed by transmission electron microscope, and the coverage of PANI particles onto the core surfaces was improved. The key point of formation of rod‐type PANI particles was that DBSA was served with a high concentration accompanied with the existence of HCl or SDS. The better coverage of PANI particles over the core surfaces by charging higher DBSA concentrations resulted in a higher conductivity of hybrid particles. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3902–3911, 2007     

Micelle-assisted synthesis of polyaniline/magnetite nanorods by in situ self-assembly process

Polyaniline/magnetite nanocomposites consisting of polyaniline (PANI) nanorods surrounded by magnetite nanoparticles were prepared via an in situ self-assembly process in the presence of PANI nanorods. The synthesis is based on the well-known chemical oxidative polymerization of aniline in an acidic environment, with ammonium persulfate (APS) as the oxidant. An organic acid (dodecylbenzenesulfonic acid, DBSA) was used to replace the conventional strong acidic (1 M HCl) environment. Here, dodecylbenzenesulfonic acid is used not only as dopant, but also as surfactant in our reaction system. So, DBSA can excellently control the morphology and size of PANI nanorods and magnetite particles. Magnetite particles were formed simultaneously during sedimentation, and the formed nanorods were also decorated by the particles. The resulting PANI/magnetite composites were characterized using scanning electron microscopy (SEM), X-ray diffraction (XRD), and thermogravimetric analysis (TGA). It is found that PANI/magnetite nanorod composites have uniform size, superparamagnetism and a small mass fraction of magnetite, thermal stabilization even at a higher temperature.     

Alkyl‐Group Selection in an Acidic‐Surfactant‐Promoted Reaction of Homoallyl Alcohols and Aldehydes in Water

The hydrophobic effect in the reaction of a homoallyl alcohol with an aldehyde (Yadav's reaction system) under aqueous conditions in the presence of an acidic surfactant was studied indicating the presence of the alkyl‐substituent effect, although not a dramatic one. The DBSA‐promoted reaction proceeds relatively faster when both the homoallyl alcohol and the aldehyde carry a cycloalkyl group (DBSA=4‐dodecylbenzenesulfonic acid). In contrast, the reaction of the substrates having an unbranched alkyl group is relatively more favorable in SDS/HCl than in DBSA (SDS=sodium dodecyl sulfate).     

Interaction between polymer and anionic/nonionic surfactants and its mechanism of enhanced oil recovery

Various experimental methods were used to investigate interaction between polymer and anionic/nonionic surfactants and mechanisms of enhanced oil recovery by anionic/nonionic surfactants in the present paper. The complex surfactant molecules are adsorbed in the mixed micelles or aggregates formed by the hydrophobic association of hydrophobic groups of polymers, making the surfactant molecules at oil-water interface reduce and the value of interfacial tension between oil and water increase. A dense spatial network structure is formed by the interaction between the mixed aggregates and hydrophobic groups of the polymer molecular chains, making the hydrodynamic volume of the aggregates and the viscosity of the polymer solution increase. Because of the formation of the mixed adsorption layer at oil and water interface by synergistic effect, ultra-low interfacial tension (～2.0?×?10^?3 mN/m) can be achieved between the novel surfactant system and the oil samples in this paper. Because of hydrophobic interaction, wettability alteration of oil-wet surface was induced by the adsorption of the surfactant system on the solid surface. Moreover, the studied surfactant system had a certain degree of spontaneous emulsification ability (D50?=?25.04?µm) and was well emulsified with crude oil after the mechanical oscillation (D50?=?4.27?µm).     

Formation of Lamellar Silica from Lyotropic Liquid Crystals of Dodecyl Benzene Sulfonic Acid

The formation of lamellar mesostructured silica by a neutral route in dodecylbenzene sulfonic acid (DBSA)/aminoalkoxysilane/water systems was investigated by phase study and Small Angle X‐ray Scattering (SAXS). Initially, two lamellar lyotropic phases are found, one corresponding to the DBSA and other corresponding to the DBSA‐aminoalkoxysilane salt. With the hydrolysis and condensation of siloxane groups, the DBSA‐aminoalkoxysilane lyotropic phase disappears and lamellar silica is formed. The lyotropic phase does not act as a true template but as a source of amphiphilic molecules, hence synthesis takes place via a phase separation mechanism. This synthesis route provides an easy way to prepare amino functionalized lamellar silica.     

蛇油的挥发性成分分析和脱腥

采用水蒸汽蒸馏、黏土吸附、乙醇-乙酸乙酯共沸的方法除去蛇油的腥味,运用顶空固相微萃取(SPME)-气相色谱(GC)-质谱(MS)联用技术分析脱腥前后蛇油中挥发性成分的变化,并运用GC-MS联用技术分析脱腥后的蛇油中的脂肪酸.结果表明水蒸汽蒸馏是效果最佳的脱腥方法,它可使蛇油挥发性成分的量降至脱腥前的38%,使腥味的主要成分减少60%～100%,同时较大程度地保留了多不饱和脂肪酸.     

Wettability of Freon hydrates in crude oil/brine emulsions

The surface energy of petroleum hydrates is believed to be a key parameter with regard to hydrate morphology and plugging tendency in petroleum production. As of today, the surface energy of natural gas hydrates is unknown, but will depend on the fluids in which they grow. In this work, the wettability of Freon hydrates is evaluated from their behavior in crude oil emulsions. For emulsions stabilized by colloidal particles, the particle wettability is a governing parameter for the emulsion behavior. The transition between continuous and dispersed phases as a function of brine volume in crude oil-brine emulsions containing Freon hydrates has been determined for 12 crude oils. Silica particles are used for comparison. The results show that phase inversion is highly dependent on crude oil properties. Based on the measured points of phase inversion, the wettability of the Freon hydrates generated in each system is evaluated as being oil-wet, intermediate-wet, or water-wet. Generation of oil-wet hydrates correlates with low hydrate plugging tendency. The formation of oil-wet hydrates will prevent agglomeration into large hydrate aggregates and plugs. Hence, it is believed that the method is applicable for differentiating oils with regard to hydrate morphology.     

Determination of volatile and non-volatile nickel and vanadium compounds in crude oil using electrothermal atomic absorption spectrometry after oil fractionation into saturates, aromatics, resins and asphaltenes

In recent work, it has been shown that electrothermal atomic absorption spectrometry (ET AAS) can be used to differentiate between volatile and non-volatile nickel and vanadium compounds in crude oil. In the present work, the distribution of these two groups of compounds over different fractions of crude oil was investigated. For this purpose two crude oil samples were separated in two steps: firstly, the asphaltenes were precipitated with n-heptane, and secondly, the maltenes were loaded on a silica column and eluted with solvents of increasing polarity. The four fractions of maltenes eluted from silica column were: F1, saturated and light aromatics; F2, polyaromatics; F3, resins; and F4, polar compounds. Fractions F1 and F2 were further investigated using gas chromatography, and all fractions were characterized by CHN analysis, confirming the increase of aromatics in the fractions 2, 3, 4 and asphaltenes. For the determination of Ni and V by ET AAS, oil-in-water emulsions were prepared. The speciation analysis was carried out measuring without chemical modifier (stable compounds) and with 20 μg palladium (total Ni and V) and the volatile fraction was calculated by difference. The limits of detection were 0.02 μg g⁻¹ and 0.06 μg g⁻¹, for Ni and V, respectively, based on an emulsion of 2 g of oil in 10 mL. The volatile species of Ni and V were associated with fractions F3 and F4, while only thermally stable Ni and V was precipitated in part together with the asphaltenes.     

Structure of Composite Films Containing Polyaniline Studied by DSC

A structural study of conductive composite films consisting of ethylene-co-vinylacetate (EVA) copolymer, polyaniline (PANI) and dodecylbenzenesulfonic acid (DBSA), a part of which being complexed with PANI, was performed by using differential scanning calorimetry (DSC) and presented for the first time. An additional crystalline phase is formed during the film formation by thickening EVA chain-folded lamellae with participation of‘free’ DBSA molecules at lower net PANI content (up to 5 mass%) and of both ‘free’ and complexed DBSA molecules (up to 7.5 mass%). At higher PANI content PANI-DBSA complex starts to form its own crystals and at 17.5 mass% of PANI mixed crystals of EVA with ‘free’ DBSA alkyl chains are preferably formed. It is also found that the Fox' equation correlating the glass transition temperature of a miscible blend system with its composition can be actually used in estimating the miscibility of EVA/PANI blends no matter the presence of DBSA. This revised version was published online in August 2006 with corrections to the Cover Date.     

Structure, bonding, and aggregation of selenium-containing organolithium species

1,3-Dioxo compounds can be prepared from selenium-mediated carbonylation of lithium enolates in the presence of carbon monoxide. Intermediates in this reaction include several organic species that contain both selenium and lithium. The first step in understanding the detailed reaction mechanism is to understand the structure of these intermediates. Like most organolithium compounds, these species can exist as aggregates in solution. The B3LYP density functional theory (DFT) method was used to examine the gas phase and THF solvated structures of these compounds. The calculations showed that each of the compounds forms dimers or higher aggregates in the gas phase. Aggregates are also formed in THF solution, although solvation favors lower aggregates as compared to the gas phase.     

Surface Properties and Etherification in Microemulsion Systems of Novel Brönsted Acid Surfactants

Novel Brönsted acid-surfactants with different alkyl chains were synthesized via a two-step process, and their surface properties were studied. The critical micelle concentration(cmc), surface tension at the cmc(γ_cmc), and ability of these compounds to lower the surface tension by 0.02 N/m(C₂₀ and pC₂₀) were investigated at 25 and 40℃. The molecular architecture of the compounds strongly influenced these physicochemical parameters. The ability of these compounds to lower surface tension was found to be good. Etherification in microemulsions formed by these surfactants as well as dodecylbenzenesulfonic acid(DBSA) was performed; surfactants 3a and 3b were found to be much more efficient than dodecylbenzenesulfonic acid(DBSA).     

Targeted Synthesis of a Highly Stable Aluminium Phosphonate Metal–Organic Framework Showing Reversible HCl Adsorption

A concept for obtaining isoreticular compounds with tri- instead of tetravalent metal cations using highly acidic reaction conditions was developed and successfully applied in a high throughput study using N,N′-piperazinebis(methylenephosphonic acid) (H₄PMP), that resulted in the discovery of a new porous aluminium phosphonate denoted CAU-60⋅6 HCl. The high-throughput study was subsequently extended to other trivalent metal ions. Al-CAU-60⋅6 HCl demonstrates reversible desorption of HCl (18.3 wt % loading) with three distinct compositions observed with zero, four or six HCl molecules per formula unit. Structural changes were followed in detail by powder X-ray diffraction, EDX analysis as well as IR spectroscopy. Rapid desorption of HCl in water within minutes and subsequent adsorption from the gas phase and from aqueous solution are shown. Furthermore, it is possible to adsorb HBr into the guest free Al-CAU-60 framework, demonstrating the high stability of this compound.     

Characterization of suspended solids in produced water in Daqing oilfield

The concentration and size of suspended solids (SS) in the treated produced water beyond the criteria of injection water in Daqing oilfield have raised great concerns in recent years. The SS in produced water from water, polymer and alkali–surfactant–polymer (ASP) flooding were successfully separated and characterized using some analytical techniques in this study. X-ray fluorescence (XRF), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR), and heating method reveal that some organic compounds besides crude oil were present in the SS samples, and polyacrylamide was found in the SS from polymer and ASP flooding. X-ray diffraction (XRD) shows some crystal inorganic substances such as SiO₂, Fe₂O₃, Fe₃O₄, and BaSO₄ in the SS samples, and XPS analysis indicated that several iron compounds with different valences were present in the three SS samples. The mean diameters of three SS samples were 22.89, 11.28 and 17.61 μm, respectively. Most importantly, the aggregates formed by the SS and oil droplets as well as the small SS adsorbed on the surface of oil droplets were observed using a microscope, indicating that the SS can be removed with crude oil, and crude oil also contributes to the determination of the SS values.     

Counter-current chromatography for oil analysis: Retention features and kinetic effects

Application of counter-current chromatography (CCC) for oil analysis has been suggested for the first time. CCC looks very promising as a tool for pre-concentration and isolation of trace elements from oil. Features of stationary phase retention of two-phase liquid systems (oil or oil products–aqueous nitric acid solutions) in CCC have been investigated. The influence of physicochemical properties of crude oil and oil products used as a mobile phase on the volume of stationary phase (acidic aqueous solutions) retained in CCC was studied. Chromatographic behavior of several oil samples was studied. It has been shown that physicochemical properties of test oil influence its chromatographic behavior. Optimal values of density and viscosity (ρ < 0.85 g/cm³, n < 7 cSt) of crude oil and oil products that could be analyzed using CCC were estimated. The influence of the column rotational speed and flow rate of mobile phase on the stationary phase retention was also investigated. It is known that kinetic aspects (mass transfer of elements between phases) can play a very important role in selecting an optimal composition of stationary phase for the pre-concentration of elements from oil. The influence of nitric acid concentration in the stationary phase on mass transfer was studied. Kinetic characteristic for trace element recovery has been investigated for the optimization of pre-concentration conditions of trace elements from crude oil and oil products. The extraction recoveries of Zn, Mn, Fe, Ni, V, Cu, Cd, Pb and Ba by CCC in dynamic mode are in the range of 75–95% while they are lower than 35% under batch conditions.     

Water pH and surfactant addition effects on the stability of an Algerian crude oil emulsion

In many oil production sites water injection is used as a piston to push the crude out of the well. As the age of the field progresses, the ratio of water to oil produced increases. Agitation of a water and crude oil mixture may give stable water-in-oil emulsion in which the water remains dispersed for a long period of time. These emulsions can cause severe problems in production and transport processes since they normally possess high stability and viscosity. The most important water properties which may contribute to the emulsion stability include pH and additive content. In this study, we report on the effect of both, water pH and the presence of surfactant molecules (anionic, cationic or non-ionic) on the stability of an Algerian crude oil (Haoudh el Hamra well) aqueous emulsion prepared by a mechanical agitation procedure. The stability was followed by the test-bottle method to measure the resolved water separated from the emulsion, and optical microscopy to visualize the dispersed water droplets in the oil phase. The results of the effects of varying the aqueous-phase pH suggest that the neutral medium is more efficient than acidic or basic environment for stabilizing the emulsions. The addition of non-ionic surfactants has a better potential to improve crude oil emulsion stability with respect to both cationic and anionic surfactants which do not show any improvement in the oil/water phase compatibility.