Effects of orientation on dynamic shear behavior of some amorphous polymers from 4.2° to 300°K

The dynamic shear behavior of four highly amorphous polymers in the unstretched and stretched states (draw ratios 3:1 to 6:1) was investigated with a torsion pendulum at temperatures from 4.2°K to 180–300°K and frequencies from 0.4 to 3.2 cps. The polymers studied were polystyrene, poly(vinyl acetate), poly(vinyl propionate), and poly(isobutyl vinyl ether). Previously unreported loss maxima were found at 48°K (1.5 cps) and 149°K (1.3 cps) for poly(vinyl proplonate), at 10°K (1.0 cps) for poly(vinyl acetate) and at 9°K (1.6 cps) for poly(isobutyl vinyl ether). Uniaxial orientation increased the shear storage modulus G, measured with the torsion axis parallel to the stretch direction and caused changes in the loss peaks which depended on the polymer material studied.     

Conductivity of carbon black-loaded styrene–butadiene rubber

Styrene–butadiene rubber (SBR) charged with 50 phr of HAF carbon black has been found to show a positive temperature coefficient of resistivity close to 0.07/°C at 27°C. Beyond a point (75°C) of minimum conductivity, however, it behaves as a normal noncrystalline semiconductor with a resistivity which decreases with rise of temperature with an activation energy of 0.56 eV. Blending the composition with poly(vinyl chloride) (PVC) shifts the minimum towards lower temperatures. The descending branch of the conductivity versus reciprocal absolute temperature characteristic is probably associated with thermal expansion of tunnelling paths separating the conducting carbon particles.     

Effects of temperature on cure kinetics and mechanical properties of vinyl–ester resins

The relationships among cure temperature, chemical kinetics, microstructure, and mechanical performance have been investigated for vinyl–ester resins. Fourier transform infrared spectroscopy was used to follow the reactions of vinyl–ester and styrene during isothermal curing of Dow Derakane 411‐C‐50 at 30 and 90°C. Reactivity ratios of vinyl–ester and styrene vinyl groups were evaluated using the copolymer composition equation. The results indicate that the ratio of vinyl–ester to styrene double bonds incorporated into the network is greater for 30 than for 90°C cure. Mechanical properties were obtained for systems subjected to isothermal cures at 30 and 90°C and postcured above ultimate T_g. The results show that the initial cure temperature significantly affects the mechanical behavior of vinyl–ester resin systems. In particular, values of strength and fracture toughness for postcured samples initially cured isothermally at 30°C are significantly higher than those obtained for samples cured isothermally at 90°C. Examination of fracture surfaces using atomic force microscopy revealed the existence of a nodular microstructure possessing characteristic nodule dimensions that are affected by the temperature of cure. Such features suggest the existence of phase separation during cure. A binary interaction model in conjunction with chemical kinetic data and estimated solubility parameters was used to evaluate enthalpic interactions between the growing polymer network and monomers of the vinyl–ester system. The results indicate that the interaction energy becomes increasingly endothermic as cure progresses and that this energy is affected by the temperature of cure through differences in copolymerization behavior. Hence, in addition to entropic factors, the changes in enthalpic contribution to the Gibbs free energy suggest that the probability of phase separation increases with extent of cure and that its onset is potentially affected by cure temperature. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 725–744, 1999     

Thermodynamic properties of some concentrated polymer solutions

Solubilities of several solvents were measured in four molten polymers by using an isobaric vapor-pressure apparatus. Solvent concentration ranged from 0.5 to 15 wt-%. The systems polyisoprene–benzene and polyisobutylene–benzene were studied at 80.0°C; polyisobutylene–cyclohexane was studied at 100.0°C; ethylene–vinyl acetate copolymer (EVA)–cyclohexane, EVA–isooctane, and poly(vinyl acetate)–isooctane were studied at 110.0°C. Of six polymer–solvent systems studied, all except poly(vinyl acetate)–isooctane appear to exhibit hysteresis in a single sorption–desorption cycle starting with dry polymer. The desorption curves of solvent activity plotted versus solvent weight fraction show an inflection point, suggesting localized adsorption of solvent molecules. Experimental data were analyzed with a theory which takes into account adsorption of solvent by polymer in addition to differences in free volumes and intermolecular forces. The theory gives a semiquantitative representation of the experimental data.     

Isoindolium-Based Allenes: Reactivity Studies and Applications in Fluorescence Temperature Sensing and Cysteine Bioconjugation

The reaction of a series of electron-deficient isoindolium-based allenes with sulfhydryl compounds has been studied, leading to the formation of isoindolium-based vinyl sulfides. The vinyl sulfides generated could be readily converted into the corresponding indanones and amines upon heating at 30–70 °C with good yields up to 61 %. The thermal cleavage reaction of vinyl sulfides was further studied for developing temperature-sensitive systems. Notably, a novel FRET-based fluorescent temperature sensor was designed and synthesized for temperature sensing at 50 °C, giving a 6.5-fold blue fluorescence enhancement. Moreover, chemoselective bioconjugation of cysteine-containing peptides with the isoindolium-based allenes for the construction of multifunctional peptide bioconjugates was investigated. Thermal cleavage of isoindoliums on the modified peptides at 35–70 °C gave indanone bioconjugates with up to >99 % conversion. These results indicated the biocompatibility of this novel temperature-sensitive reaction.     

One-Pot Vinylation of Secondary Phosphine Chalcogenides with Vinyl Sulfoxides

A facile, one-pot vinylation of secondary phosphine chalcogenides with alkyl(or aryl) vinyl sulfoxides has been elaborated. The vinylation comprises the nucleophilic addition of secondary phosphine chalcogenides to the vinyl sulfoxides (～50 mol% KOH, dioxane, 25–40°C, 1 h) followed by the elimination of sulfenic acids from the adducts (additional equivalent of KOH, 60–70°C, 1.5–2.0 h), the yields of target tertiary vinyl phosphine chalcogenides reaching 92%.     

Compatibility of poly(ethylene oxide)–poly(vinyl acetate) blends

The compatibility of poly(ethylene oxide)–poly(vinyl acetate) (PEO-PVA) blends was examined at five compositions covering the complete range. Samples were prepared by coprecipitation and solution casting. Dynamic mechanical properties were studied at 110 Hz between ?120 and 65°C for dry, quenched, and annealed samples. The study also included tensile testing at 25°C, examination of blend morphology, and DSC measurements at elevated temperatures. Optical microscopy revealed that crystallization of PEO proceeds essentially unhindered at up to 25% poly(vinyl acetate) content by weight. Higher levels of this component drastically reduce spherulite size, and at the highest PVA compositions there was no evidence of crystallization. Thermomechanical spectra of quenched and annealed samples indicate limited mixing of the two components except for the higher (>75%) PVA compositions. Tensile properties show a mutual reinforcement at 10-25% PVA content due to possible polymer segment association. The melting-point depression of PEO is significant above 25% PVA and has been attributed to morphological changes of the PEO crystalline phase.     

Reaction of vinyl sulfoxides with sodium sulfide and polysulfides

Sodium sulfide and polysulfides readily (50–55°C, 3 h, aqueous medium) react with alkyl vinyl sulfoxides to afford bis(alkylsulfinylethyl)sulfides and-polysulfides in up to 75% yield. Under comparable conditions the reaction of divinyl sulfoxide with sodium sulfide proceeds by the mechanism of addition-cyclization and results in 1,4-dithiane-1-oxide and 1,4-oxathiane-4-oxide. Microwave activation of the studied reactions allows to increase their rate and efficiency.     

13C-NMR spectroscopic analysis of vinyl groups in styrene–divinylbenzene networks

p-Divinylbenzene (DVB) ¹³C-labeled at the methine carbon of the vinyl group was copolymerized in suspension with styrene at 70, 70–95, and 135–155°C using 2,2′-azobisisobutyronitrile (AIBN) as the initiator. The number of unreacted vinyl groups in each copolymer was determined by ¹³C CP–MAS NMR analysis of solid samples, direct polarization ¹³C-NMR analysis of CDCl₃-swollen gels, and bromination. Results from the three methods agree methods agree qualitatively. Even the 1% DVB-crosslinked networks contained 40% unreacted DVB-vinyl groups when prepared by high conversion polymerization at 70°C and 16% unreacted DVB-vinyl groups when polymerization was finished at 95°C. The analyses were also applied to some commercial crosslinked polystyrenes. Every sample examined contained pendent vinyl groups     

Stereospecific polymerization of isobutyl vinyl ether catalyzed by calcined iron sulfate

The polymerization of isobutyl vinyl ether was studied in a heterogeneous system using iron (II) sulfate calcined in air at various temperatures as a catalyst. The maximum activity was shown by the catalyst calcined at 700°C, which effected the polymerization at room temperature in a few seconds, while the sulfate treated at 750°C was totally inactive. Poly(vinyl ethyl ether) was also obtained by the FeSO₄ (700°C) catalyst at room temperature. This catalyst formed the crystalline polymer (melting temperature 135–138°C) when the reaction was performed in toluene as solvent at room temperature. Poisoning experiments with Hammett indicators were carried out with the FeSO₄ (700°C) catalyst. The treatment with n-butylamine rendered it inactive in the reaction of isobutyl vinyl ether, while its catalytic activity was little affected by dicinnamalacetone. On the basis of the observed results, the nature of active sites of catalyst is discussed.     

Radical block polymerization of vinyl chloride. II. Synthesis and characterization of vinyl chloride block copolymers

Peroxidized polypropylene has been used as a heterofunctional initiator for a two-step emulsion polymerization of a vinyl monomer (M₁) and vinyl chloride with the production of vinyl chloride block copolymers. Styrene, methyl-, and n-butyl methacrylate and methyl-, ethyl-, n-butyl-, and 2-ethyl-hexyl acrylate have been used as M₁ and polymerized at 30–40°C. In the second step vinyl chloride was polymerized at 50°C. The range of chemical composition of the block copolymers depends on the rate of the first-step polymerization of M₁ and the duration of the second step; e.g., with 2-ethyl-hexyl acrylate block copolymers could be obtained with a vinyl chloride content of 25–90%. The block copolymers have been submitted to precipitation fractionation and GPC analysis. Noteworthy is the absence of any significant amount of homopolymers, as well as poly(M₁)n as PVC. The absence of homo-PVC was interpreted by an intra- and intermolecular tertiary hydrogen atom transfer from polypropylene residue to growing PVC sequences. The presence of saturated end groups on the PVC chains is responsible for the improved thermal stability of these block polymers, as well as their low rate of dehydrochlorination (180°C). Molecular aggregation in solution has been shown by molecular weight determination in benzene and tetrahydrofuran.     

Polarization studies by the TSC technique on a blend of cellulose acetate and polyvinyl acetate

The thermally stimulated current (TSC) technique has been used to study solvent-cast blends of a cellulose derivative with a vinyl polymer. TSC peaks are observed at 56, 80, and 120°C. Their origin is investigated because the TSC spectra of the blends differ from the spectra of the individual components. Data on blends with components in the weight ratios 25:75, 50:50, and 75:25 indicate that the 50:50 blend shows the greatest polarization. The enhancement of depolarization currents observed on blending is explained on the basis of a Maxwell–Wagner–Sillars polarization due to increased heterogeneity in the structure. Effects of forming conditions (time, temperature, field) on polarization have been investigated. Activation energies and relaxation times are calculated; there is good agreement between the values obtained from the initial-rise and the full-curve methods.     

3-(1-Chloro­vinyl)-2,4,6-tri­methoxy­benz­aldehyde

The title compound, C₁₂H₁₃ClO₄, was prepared from the Vilsmeier–Haack reaction on phloroaceto­phenone. The chloro­vinyl and one of the methoxy substituents are twisted through about 75° with respect to the aromatic plane, whilst the other substituents are almost coplanar with the ring. Intermolecular hydrogen bonding involving C—H⃛O interactions generates one-dimensional chains in the direction of the a axis.     

Stimuli‐responsive ABC triblock copolymers by sequential living cationic copolymerization: Multistage self‐assemblies through micellization to open association

Stimuli‐responsive ABC triblock copolymers with three segments with different phase‐separation temperatures were synthesized via sequential living cationic copolymerization. The triblock copolymers exhibited sensitive thermally induced physical gelation (open association) through the formation of micelles. For example, an aqueous solution of EOVE₂₀₀‐b‐MOVE₂₀₀‐b‐EOEOVE₂₀₀ [where EOVE is 2‐ethoxyethyl vinyl ether, MOVE is 2‐methoxethyl vinyl ether and EOEOVE is 2‐(2‐ethoxy)ethoxyethyl vinyl ether; the order of the phase‐separation temperatures was poly(EOVE) (20 °C) < poly(EOEOVE) (41 °C) < poly(MOVE) (70 °C)] underwent multiple reversible transitions from sol (<20 °C) to micellization (20–41 °C) to physical gelation (physical crosslinking, 41–64 °C) and, finally, to precipitation (>64 °C). At 41–64 °C, the physical gel became stiffer than similar diblock or ABA triblock copolymers of the same molecular weight. Furthermore, the ABC triblock copolymers exhibited Weissenberg effects in semidilute aqueous solutions. In sharp contrast, another ABC triblock copolymer with a different arrangement, EOVE₂₀₀‐b‐EOEOVE₂₀₀‐b‐MOVE₂₀₀, scarcely exhibited any increase in viscosity above 41 °C. The temperatures of micelle formation and physical gelation corresponded to the phase‐separation temperatures of the segment types in the ABC triblock copolymer. No second‐stage association was observed for AB and ABA block copolymers with the same thermosensitive segments found in their ABC counterparts. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2601–2611, 2004     

Polymerization of vinyl chloride with organolithium compounds. V. Flow behavior of concentrated solutions of high molecular weight poly(vinyl chloride) in cyclohexanone

The flow behavior of 10, 15, and 25% solutions of high molecular weight, thermally stable poly(vinyl chloride) in cyclohexanone was studied in the temperature range 50–140°C with respect to fiber-forming properties. The flow behavior of such solutions at shear rates ranging from 1–10³ sec^?1 is pronouncedly non-Newtonian with the exception of the 10% solution at 70°C. It can be adequately described by known empirical linear relationships. The apparent viscosities and activation energies are considerably higher than those for the usual types of poly(vinyl chloride), but vary within limits acceptable for the preparation and spinning of solutions.     

Colorimetric analysis of thermal degradation of plasticized poly(vinyl chloride): Potentials and limitations

The kinetics of formation and consumption of polyenes is studied by measuring the change in color coordinates and color difference during the thermal aging of plasticized poly(vinyl chloride) at a temperature of 60–130°С under vented conditions and in a closed volume. It is shown that the initial rate of accumulation and the quasi-stationary concentration of polyenes at 100–130°С grow with temperature. The energy of activation of dehydrochlorination is 70 ± 3 kJ/mol. At a lower temperature (60–80°С), the intensity of color of the samples that are preliminarily aged at increased temperatures decreases. The reduction in the rate of this process with temperature in the range of 60–80°С and the presence of the quasi-stationary level at 100–130°С are related to competition of the processes of formation and oxidation of polyenes.     

Polymerization of 2,2,2-trifluoroethyl vinyl ether

The polymerization of 2,2,2-trifluoroethyl vinyl ether by six different catalyst systems was examined. Low-temperature studies (?78°C) with boron trifluoride etherate catalyst in hydrocarbon and chlorinated solvents slowly yielded low molecular weight polymers which were amorphous and noncrystallizable upon cold drawing. Under similar conditions, polymerizations with boron trifluoride gas were spontaneous, quantitative, and gave relatively high molecular weight, form-stable, amorphous polymer. Heterogeneous polymerizations with chromium trioxide crystals in toluene at 68°C and bulk reactions with ethylmagnesium bromide–carbon tetrachloride catalyst at 40°C failed to produce polymer. Room temperature runs with triisobutylaluminum–titanium tetrachloride catalyst gave amorphous, tacky material. Aluminum hexahydrosulfate heptahydrate (AHS) initiated polymerizations conducted at 25 and 60°C gave low yields of mixtures of amorphous and crystalline polymers, the ratio depending upon the polymerization solvent employed. The infrared spectra and x-ray diffraction intensity curves of crystalline and amorphous poly(trifluoroethyl vinyl ether) are reported and compared herein for the first time.     

Polymerization of vinyl chloride in the presence of precipitants. I

The kinetics of bulk and precipitation polymerization of vinyl chloride has been studied over wide range of reaction temperature by using γ-ray induced initiation. The autoacceleration effect, which has been observed by many investigators in the case of chemically initiated bulk polymerization of vinyl chloride above 40°C and has been the most controversial aspect of the bulk polymerization of vinyl chloride, was found to disappear in the bulk polymerization below 0°C. In the bulk polymerization at 40°C, the autoacceleration effect was observed up to 20%, in agreement with the results of previous investigators, and a pronounced effect of the size of polymer particles on the time–conversion curve was observed. The kinetics of precipitation polymerization of vinyl chloride in the presence of some nonsolvents was successfully described by a oneparameter equation. A kinetic scheme, which clearly explains the zero-order reaction behavior of bulk polymerization at low temperature and the kinetic behavior of precipitation polymerization described by the empirical equation, is proposed. The autoacceleration effect in the bulk polymerization at 40°C was considered to be essentially the same phenomenon as the small retardation period observed in the bulk polymerization at low temperature.     

Effect of the liquid–liquid phase separation on the crystallization behavior of a poly(ethylene‐ran‐vinyl acetate) and paraffin wax blend

The effect of liquid–liquid phase separation (LLPS) on the crystallization behavior of poly(ethylene‐ran‐vinyl acetate) with a vinyl acetate content of 9.5 wt % (EVA‐H) in the critical composition of a 35/65 (wt/wt) EVA‐H/paraffin wax blend was investigated by small‐angle light and X‐ray scattering methods and rheometry. This blend exhibited an upper critical solution temperature (UCST) of 98°C, and an LLPS was observed between the UCST and the melting point of 88°C for the EVA‐H in the blend. As the duration time in the LLPS region increased before crystallization at 65°C, both the spherulite size and the crystallization rate of the EVA‐H increased, but the degree of the lamellar ordering in the spherulite and the degree of crystallinity of the EVA‐H in the blend decreased. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 707–715, 2000     

Alkyl vinyl esters of brassylic (tridecanedioic) acid

Brassylic acid was partially esterified at 77°C. in toluene solution with ethyl, 2-methylpentyl, or nonyl alcohol and with p-toluenesulfonic acid used as catalyst. Half-esters were isolated from the respective reaction mixtures in yields of 28, 34, and 32% after reaction times of 2,6, and 8 hr. Both recovered brassylic acid and byproduct dialkyl ester were successfully used as starting materials in subsequent esterifications. Consequently, conversion of starting materials to half-ester would be increased in a process that involved continuous recycling of byproducts. Alkyl hydrogen brassylates were vinylated at 165°C. for 8 hr. with acetylene at 360 psig. The zinc salt generated in situ from zinc oxide served as catalyst and toluene as solvent. Yields were 80–88% and purities of products were 94–95%. Samples of 2-methylpentyl vinyl brassylate and nonyl vinyl brassylate of much higher purity were obtained by preparative gas–liquid chromatography or molecular distillation. Physical properties and experimental conditions for gas–liquid chromatographic analyses of both the alkyl hydrogen and alkyl vinyl brassylates are reported.