Vinyl phenylboronic acid controlling co‐monomer for nitroxide mediated synthesis of thermoresponsive poly(2‐N morpholinoethyl methacrylate)

Low concentrations of 4‐vinylphenylboronic acid (VPBA) were copolymerized with 2‐N‐morpholinoethyl methacrylate (MEMA) by nitroxide mediated polymerization using BlocBuilder? unimolecular initiator at 80 to 90 °C. The MEMA/VPBA copolymerizations were performed at initial feed compositions (f_VPBA,0) of 0.05 to 0.10 VPBA, with f_VPBA,0 = 0.10 using dimethylacetamide (DMAc) solvent being most effective, as seen by a linear increase in number average molecular weight, M_n, versus conversion and low dispersity, ? < 1.40. The copolymers were further chain‐extended with a second batch of VPBA, resulting in a block copolymer with monomodal molecular weight distribution and ? = 1.66. For MEMA/VPBA copolymers, increases in VPBA composition and polymer solution concentration resulted in decreases in the cloud point temperature (CPT, typically varied between 27.4–37.8 °C) and CPT increased from 31.2 to 33.8 °C to about 88 °C with decreases in pH from 7 to 4. Rheological tests with small angle light scattering (SALS) confirmed CPTs measured by UV‐Vis and DLS. These copolymers were targeted as models to combine possible glucose‐sensing boronic acid functionality the thermoresponsiveness provided by MEMA groups. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1560–1572     

Pyrrolidone‐functional smart polymers via nitroxide‐mediated polymerization

Nitroxide‐mediated polymerization (NMP) of N‐(2‐methacryloyloxyethyl) pyrrolidone (MAEPYR) with 2‐([tert‐butyl[1‐(diethoxyphosphoryl)‐2,2‐dimethylpropyl]amino]oxy)‐2‐methylpropanoic acid (BlocBuilder) initiator and N‐tert‐butyl‐N‐[1‐diethylphosphono‐(2,2‐dimethylpropyl)] (SG1) nitroxide permitted controlled synthesis of poly(N‐(2‐methacryloyloxyethyl)‐pyrrolidone‐stat‐9‐(4‐vinylbenzyl)‐9H‐carbazole) (poly(MAEPYR‐stat‐VBK)) statistical copolymers. With at least 5 mol % VBK, the dispersity ? of the copolymers was below 1.4 at conversions less than 50%. At conversions higher than 50%, and at lower VBK feed content, there was a significant amount of termination reactions, which broadened the molecular weight distribution of the final polymers (? = 1.4–2.3). The MAEPYR‐rich statistical copolymers were subsequently tested for thermoresponsive behavior in aqueous media. The cloud point temperatures (CPTs) in aqueous solution were tuned by changing the VBK composition, solution concentration, and heating rate, and the transitions were thermally reversible with partial loss of reversibility at higher heating rates. The CPT decreased from 59.0 to 49.7 °C with addition of only 1 mol % of VBK in the copolymer, and at more than 6 mol % VBK, the copolymer was water insoluble. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2011–2024     

Combination of nitroxide‐mediated polymerization and SET‐LRP for the synthesis of high molar mass branched and star‐branched poly(n‐butyl acrylate) characterized by size exclusion chromatography and rheology

Branched and star‐branched polymers were successfully synthesized by the combination of two successive controlled radical polymerization methods. A series of linear and star poly(n‐butyl acrylate)‐co‐poly(2‐(2‐bromoisobutyryloxy) ethyl acrylate) statistical copolymers, P(nBA‐co‐BIEA)_x, were first synthesized by nitroxide‐mediated polymerization (NMP at T > 100 °C). The subsequent polymerization of n‐butyl acrylate by single electron transfer‐living radical polymerization (SET‐LRP at T = 25 °C), initiated from the brominated sites of the P(nBA‐co‐BIEA)_x copolymer, produced branched or star‐branched poly(n‐butyl acrylate) (PnBA). Both types of polymerizations (NMP and SET‐LRP) exhibited features of a controlled polymerization with linear evolutions of logarithmic conversion versus time and number‐average molar masses versus conversion for final M_n superior to 80,000 g mol^?1. The branched and star‐branched architectures with high molar mass and low number of branches were fully characterized by size exclusion chromatography. The Mark–Houwink Sakurada relationship and the analysis of the contraction factor (g′ = ([η]_branched/[η]_linear)_M) confirmed the elaboration of complex PnBA. The zero‐shear viscosities of the linear, star‐shaped, branched, and star‐branched polymers were compared. The modeling of the rheological properties confirmed the synthesis of the branched architectures. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Temperature‐induced aggregation of the copolymers of N‐isopropylacrylamide and sodium 2‐acrylamido‐2‐methyl‐1‐propanesulphonate in aqueous solutions

A series of random copolymers of N‐isopropylacrylamide (NIPAM) and sodium 2‐acrylamido‐2‐methyl‐1‐propanesulphonate (AMPS) was synthesized by free‐radical copolymerization. The content of AMPS in the copolymers ranged from 1.1 to 9.6 mol %. The lower critical‐solution temperature (LCST) of copolymers in water increased strongly with an increasing content of AMPS. The influence of polymer concentration on the LCST of the copolymers was studied. For the copolymers with a higher AMPS content, the LCST decreased faster with an increasing concentration than for copolymers with a low content of AMPS. For a copolymer containing 1.1 mol % of AMPS the LCST dropped by about 3 °C when the concentration increased from 1 to 10 g/L, whereas for a copolymer containing 9.6 mol % of AMPS the LCST dropped by about 10 °C in the concentration range from 2 to 10 g/L. It was observed that the ionic strength of the aqueous polymer solution very strongly influences the LCST. This effect was most visible for the copolymer with the highest content of AMPS (9.6 mol %) for which an increase in the ionic strength from 0.2 to 2.0 resulted in a decrease in the LCST by about 27 °C (from 55 to 28 °C), whereas for the copolymer containing 1.1 mol % of AMPS the LCST decreased only by about 6 °C (from 37 to 31 °C) when the ionic strength increased from 0.005 to 0.3. The reactivity ratios for the AMPS and NIPAM monomer pairs were determined using different methods. The values of r_AMPS and r_NIPAM obtained were 11.0–11.6 and 2.1–2.4, respectively. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2784–2792, 2001     

Nitroxide‐mediated radical copolymerization of methyl methacrylate controlled with a minimal amount of 9‐(4‐vinylbenzyl)‐9H‐carbazole

The controlled nitroxide‐mediated homopolymerization of 9‐(4‐vinylbenzyl)‐9H‐carbazole (VBK) and the copolymerization of methyl methacrylate (MMA) with varying amounts of VBK were accomplished by using 10 mol % {tert‐butyl[1‐(diethoxyphosphoryl)‐2,2‐dimethylpropyl]amino} nitroxide relative to 2‐({tert‐butyl[1‐(diethoxyphosphoryl)‐2,2‐dimethylpropyl]amino}oxy)‐2‐methylpropionic acid (BlocBuilder?) in dimethylformamide at temperatures from 80 to 125 °C. As little as 1 mol % of VBK in the feed was required to obtain a controlled copolymerization of an MMA/VBK mixture, resulting in a linear increase in molecular weight versus conversion with a narrow molecular weight distribution (M_w /M_n ≈ 1.3). Preferential incorporation of VBK into the copolymer was indicated by the MMA/VBK reactivity ratios determined: r_VBK = 2.7 ± 1.5 and r_MMA = 0.24 ± 0.14. The copolymers were found significantly “living” by performing subsequent chain extensions with a fresh batch of VBK and by ³¹P NMR spectroscopy analysis. VBK was found to be an effective controlling comonomer for NMP of MMA, and such low levels of VBK comonomer ensured transparency in the final copolymer. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Radical copolymerization of chlorotrifluoroethylene with 4‐bromo‐3,3,4,4‐tetrafluorobut‐1‐ene

The radical copolymerization of chlorotrifluoroethylene (CTFE) with 3,3,4,4‐tetrafluoro‐4‐bromobut‐1‐ene (BTFB) initiated by tert‐butylperoxypivalate is presented. The microstructures of the obtained copolymers are determined by means of NMR spectroscopies and elemental analysis and show that random copolymers were obtained. A wide range of poly(CTFE‐co‐BTFB) copolymers is synthesized, containing from 17 to 89 mol % of CTFE. In all the cases, CTFE is the less reactive of both comonomers. T_d^10% values, ranging from 163 up to 359 °C, are dependent on the BTFB content. These variations of thermal property are attributed to the increase in the number of C‐H and C‐Br bonds breakdown when the BTFB molar percentage in the copolymer is higher. T_g values range from 19 to 39 °C and a decreasing trend is observed when increasing the amount of BTFB in the copolymer. This observation arises from the higher flexibility of the copolymer when increasing the number of fluorobrominated lateral chains. These original fluoropolymers bearing reactive pendant bromo groups are suitable candidates for various applications. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1714–1720     

“Smart” poly(2‐(dimethylamino)ethyl methacrylate‐ran‐9‐(4‐vinylbenzyl)‐9H‐carbazole) copolymers synthesized by nitroxide mediated radical polymerization

A series of poly(2‐(dimethylamino)ethyl methacrylate‐ran‐9‐(4‐vinylbenzyl)‐9H‐carbazole) (poly(DMAEMA‐ran‐VBK)) random copolymers, with VBK molar feed compositions f_VBK,0 = 0.02–0.09, were synthesized using 10 mol % [tert‐butyl[1‐(diethoxyphosphoryl)‐2,2‐dimethylpropyl]amino] nitroxide (SG1) relative to 2‐([tert‐butyl[1‐(diethoxyphosphoryl)‐2,2‐dimethylpropyl]amino]oxy)‐2‐methylpropionic acid (BlocBuilder) at 80 °C and 90 °C. Controlled polymerizations were observed, even with f_VBK,0 = 0.02, as reflected by a linear increase in number average molecular weight (M_n) versus conversion X ≤ 0.6 with final copolymers characterized by relatively narrow, monomodal molecular weight distributions (M_w/M_n ≈ 1.5). Poly(DMAEMA‐ran‐VBK) copolymers were deemed sufficiently pseudo‐“living” to reinitiate a second batch of N,N‐dimethylacrylamide (DMAA), with very few apparent dead chains, as indicated by the monomodal shift in the gel permeation chromatography chromatograms. Poly(DMAEMA‐ran‐VBK) random copolymers exhibited tuneable lower critical solution temperature (LCST), in aqueous solution, by modifying copolymer composition, solution pH and by the addition of the water‐soluble poly(DMAA) segment. ¹H NMR analysis determined that, in water, the VBK units of the poly(DMAEMA‐ran‐VBK) random copolymer were segregated to the interior of the copolymer aggregate regardless of solution temperature and that poly(DMAEMA‐ran‐VBK)‐b‐poly(DMAA) block copolymers formed micelles above the LCST. In addition, the final random copolymer and block copolymer exhibited temperature dependent fluorescence due to the VBK units. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis of polyphenylquinoxaline copolymers via aromatic nucleophilic substitution reactions of an A‐B quinoxaline monomer

A self‐polymerizable quinoxaline monomer (A‐B) has been synthesized and polymerized via aromatic nucleophilic substitution reactions. An isomeric mixture of self‐polymerizable quinoxaline monomers—2‐(4‐hydroxyphenyl)‐3‐phenyl‐6‐fluoroquinoxaline and 3‐(4‐hydroxyphenyl)‐2‐phenyl‐6‐fluoroquinoxaline—was polymerized in N‐methyl‐2‐pyrrolidinone (NMP) to afford high molecular weight polyphenylquinoxaline (PPQ) with intrinsic viscosities up to 1.91 dL/g and a glass‐transition temperature (T_g) of 251 °C. A series of comonomers was polymerized with A‐B to form PPQ/polysulfone (PS), PPQ/polyetherether ketone (PEEK), and PPQ/polyethersulfone (PES) copolymers. The copolymers readily obtained high intrinsic viscosities when fluorine was displaced in NMP under reflux. However, single‐electron transfer (SET) side reactions, which limit molecular weight, played a more dominant role when chlorine was displaced instead of fluorine. SET side reactions were minimized in the synthesis of PPQ/PS copolymers through mild polymerization conditions in NMP for longer polymerization times. Thus, the T_g's of PES (T_g = 220 °C), PEEK (T_g = 145 °C), and PS (T_g = 195 °C) were raised through the incorporation of quinoxaline units into the polymer. Copolymers with high intrinsic viscosities resulted in all cases, except in the case of PPQ/PEEK copolymers when 4,4′‐dichlorobenzophenone was the comonomer. © 2001 John Wiley & Sons, Inc. J Polym Sci A Part A: Polym Chem 39: 2037–2042, 2001     

Syntheses and properties of organosoluble polyimides based on 5,5′‐bis[4‐(4‐aminophenoxy)phenyl]‐4, 7‐methanohexahydroindan

A series of organosoluble aromatic polyimides (PIs) was synthesized from 5,5′‐bis[4‐(4‐aminophenoxy)phenyl]‐4,7‐methanohexahydroindan (3) and commercial available aromatic dianhydrides such as 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA), 4,4′‐oxydiphthalic anhydride (ODPA), 4,4′‐sulfonyl diphthalic anhydride (SDPA), or 2,2′‐bis(3,4‐dicarboxyphenyl) hexafluoropropanic dianhydride (6FDA). PIs (III_c–f), which were synthesized by direct polymerization in m‐cresol, had inherent viscosities of 0.83–1.05 dL/g. These polymers could easily be dissolved in N,N′‐dimethylacetamide (DMAc), N‐methyl‐2‐pyrrolidone (NMP), N,N‐dimethylformamide (DMF), pyridine, m‐cresol, and dichloromethane. Whereas copolymerization was proceeded with equivalent molar ratios of pyromellitic dianhydride (PMDA)/6FDA, 3,3′,4,4′‐benzophenonetetracarboxylic dianhydride (BTDA)/6FDA, or BTDA/SDPA, or ½ for PMDA/SDPA, copolyimides (co‐PIs), derived from 3 and mixed dianhydrides, were soluble in NMP. All the soluble PIs could form transparent, flexible, and tough films, and they showed amorphous characteristics. These films had tensile strengths of 88–111 MPa, elongations at break of 5–10% and initial moduli of 2.01–2.67 GPa. The glass transition temperatures of these polymers were in the range of 252–311°C. Except for III_e, the 10% weight loss temperatures (T_d) of PIs were above 500°C, and the amount of carbonized residues of the PIs at 800°C in nitrogen atmosphere were above 50%. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1681–1691, 1999     

Using controlled radical polymerization to confirm the lower critical solution temperature of an N‐(alkoxyalkyl) acrylamide polymer in aqueous solution

N‐(3‐Methoxypropyl) acrylamide (MPAM) was polymerized by controlled radical polymerization (CRP) methods such as nitroxide‐mediated polymerization (NMP) and reversible addition–fragmentation chain‐transfer polymerization (RAFT). CRP was expected to yield well‐defined polymers with sharp lower critical solution temperature (LCST) transitions. NMP with the BlocBuilder (2‐([tert‐butyl[1‐(diethoxyphosphoryl)‐2,2‐dimethylpropyl]amino]oxy)‐2‐methylpropanoic acid) and SG1 ([tert‐butyl[1‐(diethoxyphosphoryl)‐2,2‐dimethylpropyl]amino] oxidanyl) initiating system revealed low yields and lack of control (high dispersity, ? ～ 1.5–1.6, and inhibition of chain growth). However, RAFT was far more effective, with linear number average molecular weight, , versus conversion, X, plots, low ? ～ 1.2–1.4 and the ability to form block copolymers using N,N‐diethylacrylamide (DEAAM) as the second monomer. Poly(MPAM) (with = 13.7–25.3 kg mol^?1) thermoresponsive behavior in aqueous media revealed cloud point temperatures (CPT)s between 73 and 92 °C depending on solution concentration (ranging from 1 to 3 wt %). The and the molecular weight distribution were the key factors determining the CPT and the sharpness of the response, respectively. Poly(MPAM)‐b‐poly(DEAAM) block copolymer ( = 22.3 kg mol^?1, ? = 1.41, molar composition F_DEAAM = 0.38) revealed dual LCSTs with both segments revealing distinctive CPTs (at 75 and 37 °C for poly(MPAM) and poly(DEAAM) blocks, respectively) by both UV–Vis and dynamic light scattering. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 59–67     

2,6‐Diaminopyridine and Acrylamide‐Based Copolymers with Upper Critical Solution Temperature‐type Behavior in Aqueous Solution

A novel copolymer based on supramolecular motif 2,6‐diaminopyridine and water‐soluble acrylamide, poly[N‐(6‐acetamidopyridin‐2‐yl) acrylamide‐co‐acrylamide], was synthesized via reversible addition–fragmentation chain transfer (RAFT) polymerization with various monomer compositions. The thermoresponsive behavior of the copolymers was studied by turbidimetry and dynamic light scattering (DLS). The obtained copolymers showed an upper critical solution temperature (UCST)‐type phase transition behavior in water and electrolyte solution. The phase transition temperature was found to increase with decreasing amount of acrylamide in the copolymer and increasing concentration of the solution. Furthermore, the phase transition temperature varied in aqueous solutions of electrolytes according to the nature and concentration of the electrolyte in accordance with the Hoffmeister series. A dramatic solvent isotope effect on the transition temperature was observed in this study, as the transition temperature was almost 10–12 °C higher in D₂O than in H₂O at the same concentration and acrylamide composition. The size of the aggregates below the transition temperature was larger in D₂O compared to that in H₂O that can be explained by deuterium isotope effect. The thermoresponsive behavior of the copolymers was also investigated in different cell medium and found to be exhibited UCST‐type phase transition behavior in different cell medium. Such behavior of the copolymers can be useful in many applications including biomedical, microfluidics, optical materials, and in drug delivery. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019, 57, 2064–2073     

Synthesis of β‐myrcene/glycidyl methacrylate statistical and amphiphilic diblock copolymers by SG1 nitroxide‐mediated controlled radical polymerization

Bulk nitroxide‐mediated polymerization (NMP) of β‐myrcene (My)/glycidyl methacrylate (GMA) mixtures with varying GMA molar feed fraction (f_GMA,0 = 0.10–0.91) was accomplished at 120 °C, initiated by SG1‐based alkoxyamine bearing a N‐succinimidyl ester group (NHS‐BlocBuilder). Low dispersity My/GMA copolymers (Đ < 1.56) with slight number‐average molecular weights (M_ns) deviations from predicted values (M_n,theo with M_n/M_n,theo > 70%) were obtained. The copolymerization was revealed to be statistical, confirmed via Fineman–Ross (r_My = 0.80 ± 0.31 and r_GMA = 0.71 ± 0.15) and Kelen‐Tüdös (r_My = 0.48 ± 0.12 and r_GMA = 0.53 ± 0.18) approaches. Glass transition temperature (T_g) of the statistical P(My‐stat‐GMA)s increased from −77 to +43 °C as the GMA molar fraction incorporated (F_GMA) increased from 0.10 to 0.90. High SG1 chain‐end fidelity for My‐rich and GMA‐rich P(My‐stat‐GMA)s was assessed by phosphorus nuclear magnetic resonance (³¹P NMR, SG1 fraction >69 mol %) and chain‐extensions in toluene with My, GMA and styrene (S) (monomodal shift in M_n). Last, diblock P(My‐b‐GMA) was made and treated with morpholine to produce amphiphilic copolymer able to self‐organize into micelles. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 860–878     

Synthesis and properties of gradient copolymers based on 2‐phenyl‐2‐oxazoline and 2‐nonyl‐2‐oxazoline

In this study, the structure–property relationships for a series of statistical 2‐nonyl‐2‐oxazoline (NonOx) and 2‐phenyl‐2‐oxazoline (PhOx) copolymers were investigated for the first time. The copolymerization kinetics were studied and the reactivity ratios were calculated to be r_NonOx = 7.1 ± 1.4 and r_PhOx = 0.02 ± 0.1 revealing the formation of gradient copolymers. The synthesis of a systematical series of NonOx–PhOx copolymers is described, whereby the amount of NonOx was increased in steps of 10 mol %. The thermal and surface properties were investigated for this series of well‐defined copolymers. The thermal properties revealed a linear decrease in glass transition temperature for copolymers containing up to 39 wt % NonOx. Furthermore, the melting temperature of the copolymers containing 0 to 55 wt % PhOx linearly decreased most likely due to disturbance of the NonOx crystalline domains by incorporation of PhOx in the NonOx part of the copolymer. The surface energies of spincoated polymer films revealed a strong decrease in surface energy upon incorporation of NonOx in the copolymers due to strong phase separation between NonOx and PhOx allowing the NonOx chains to orient to the surface. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6433–6440, 2009     

Synthesis of polyallene‐based graft copolymer via 6‐methyl‐1,2‐heptadien‐4‐ol and styrene

A series of well‐defined graft copolymers with a polyallene‐based backbone and polystyrene side chains were synthesized by the combination of living coordination polymerization of 6‐methyl‐1,2‐heptadien‐4‐ol and atom transfer radical polymerization (ATRP) of styrene. Poly(alcohol) with polyallene repeating units were prepared via 6‐methyl‐1,2‐heptadien‐4‐ol by living coordination polymerization initiated by [(η³‐allyl)NiOCOCF₃]₂ firstly, followed by transforming the pendant hydroxyl groups into halogen‐containing ATRP initiation groups. Grafting‐from route was employed in the following step for the synthesis of the well‐defined graft copolymer: polystyrene was grafted to the backbone via ATRP of styrene. The cleaved polystyrene side chains show a narrow molecular weight distribution (M_w/M_n = 1.06). This kind of graft copolymer is the first example of graft copolymer via allene derivative and styrenic monomer. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5509–5517, 2007     

Synthesis,characterization, and cross‐linking of a library of statistical copolymers based on 2‐“soy alkyl”‐2‐oxazoline and 2‐ethyl‐2‐oxazoline

The synthesis of statistical copolymers consisting of 2‐ethyl‐2‐oxazoline (EtOx) and 2‐“soy alkyl”‐2‐oxazoline (SoyOx) via a microwave‐assisted cationic ring‐opening polymerization procedure is described. The majority of the resulting copolymers revealed polydispersity indices below 1.30. The reactivity ratios (r_EtOx 1.4 ± 0.3; r_SoyOx = 1.7 ± 0.3) revealed a clustered monomer distribution throughout the polymer chains. The thermal and surface properties of the pEtOx‐stat‐SoyOx copolymers were analyzed before and after UV‐curing demonstrating the decreased chain mobility after cross‐linking. In addition, the cross‐linked materials showed shape‐persistent swelling upon absorption of water from the air, whereby as little as 5 mol % SoyOx was found to provide efficient cross‐linking. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5371,–5379, 2007     

Photocurable and thermally stable polymers based on 1,4‐pentadien‐3‐one‐1‐p‐hydroxyphenyl‐5‐p‐phenyl methacrylate: Copolymerization with ethyl acrylate

1,4‐Pentadien‐3‐one‐1,5‐bis(p‐hydroxyphenyl) (PBHP) was prepared by reacting p‐hydroxybenzaldehyde and acetone in the presence of an acid catalyst. 1,4‐Pentadiene‐3‐one‐1‐p‐hydroxyphenyl‐5‐p‐phenyl methacrylate (PHPPMA) monomer was prepared by reacting PBHP dissolved in ethyl methyl ketone (EMK) with methacryloyl chloride in the presence of triethylamine. A free‐radical solution polymerization technique was used for synthesizing homo‐ and copolymers of different feed compositions of PHPPMA and ethyl acrylate (EA) in EMK as a solvent with benzoyl peroxide as a free‐radical initiator at 70 ± 1 °C. All the polymers were characterized with IR and ¹H NMR techniques. The compositions of the copolymers were determined with the ¹H NMR technique. The copolymer reactivity ratios were evolved with Kelen–Tudos (EA = 1.25 and PHPPMA = 0.09) and extended Kelen–Tudos (EA = 1.30 and PHPPMA = 0.09) methods. Q (0.48) and e (1.68) values for the new monomer (PHPPMA) were calculated with the Alfrey–Price method. UV absorption spectra for poly(PHPPMA) showed two absorption bands at 302 and 315 nm. The photocrosslinking properties of the polymer samples were examined with the solvent method. Thermal analyses of the polymers were performed with the thermogravimetric‐differential thermogravimetric technique. First, the decomposition temperatures started for poly(PHPPMA), copoly(EA‐PHPPMA) (62:38), and copoly(EA‐PHPPMA) (41:59) were at 350, 410, and 417 °C, respectively. A gel permeation chromatographic method was used for determining the polymer molecular weights (weight‐average molecular weight: 2.67 × 10⁴ and number‐average molecular weight: 1.41 × 10⁴) and polydispersity index (1.89). The solubility of the monomer and the copolymers occurred at 30 °C with solvents having different polarities. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1632–1640, 2003     

Three‐arm star block copolymers of ε‐caprolactone and acrylic acid: Synthesis and micellization behavior

A series of well‐defined three‐arm star poly(ε‐caprolactone)‐b‐poly(acrylic acid) copolymers having different block lengths were synthesized via the combination of ring‐opening polymerization (ROP) and atom transfer radical polymerization (ATRP). First, three‐arm star poly(ε‐caprolactone) (PCL) (M_n = 2490–7830 g mol^?1; M_w/M_n = 1.19–1.24) were synthesized via ROP of ε‐caprolactone (ε‐CL) using tris(2‐hydroxyethyl)cynuric acid as three‐arm initiator and stannous octoate (Sn(Oct)₂) as a catalyst. Subsequently, the three‐arm macroinitiator transformed from such PCL in high conversion initiated ATRPs of tert‐butyl acrylate (^tBuA) to construct three‐arm star PCL‐b‐P^tBuA copolymers (M_n = 10,900–19,570 g mol^?1; M_w/M_n = 1.14–1.23). Finally, the three‐arm star PCL‐b‐PAA copolymer was obtained via the hydrolysis of the PtBuA segment in three‐arm star PCL‐b‐P^tBuA copolymers. The chain structures of all the polymers were characterized by gel permeation chromatography, proton nuclear magnetic resonance (¹H NMR), and Fourier transform infrared spectroscopy. The aggregates of three‐arm star PCL‐b‐PAA copolymer were studied by the determination of critical micelles concentration and transmission electron microscope. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

High‐performance fluorine‐containing BDT‐based copolymer for organic solar cells with a high open circuit voltage

A new donor–acceptor (D‐A) conjugated copolymer (PBDTT(ff)‐ttTPD) based on fluorine‐substituted benzodithiophene (BDT) and 6‐alkylthienothienyl thieno[3,4‐c]pyrrole‐4,6‐dione (ttTPD) has been synthesized via a Stille cross‐coupling reaction. As a control, the nonfluorinated BDT‐based ttTPD copolymer (PBDTT‐ttTPD) was also synthesized by using the same polymerization method. The number‐average molecular weights (M _n) of PBDTT(ff)‐ttTPD and PBDTT‐ttTPD were found to be 48,000 g/mol (? = 2.2) and 43,000 g/mol (? = 2.1), respectively. The HOMO levels of PBDTT(ff)‐ttTPD and PBDTT‐ttTPD were calculated to be ?5.65 and ?5.45 eV, respectively. The inclusion of fluorinated BDT units is a very effective approach to lowering the polymer's HOMO level. The SCLC mobilities of PBDTT(ff)‐ttTPD and PBDTT‐ttTPD were determined to be 5.9 × 10^?4 and 3.0 × 10^?4 cm²/Vs, respectively. Polymer solar cell devices prepared with PBDTT(ff)‐ttTPD and PBDTT‐ttTPD as their active layers were found to exhibit power conversion efficiencies of 7.45 and 6.79% with open circuit voltages of 0.98 and 0.84 V, respectively. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 2506–2512     

Synthesis and properties of soluble and light‐colored poly(amide‐imide‐imide)s on the basis of tetraimide‐dicarboxylic acid condensed from 4,4′‐oxydiphthalic anhydride, 2,2‐bis[4‐(4‐aminophenoxy)phenyl]propane,and m‐aminobenzoic acid,and various aromatic diamines

A new type of tetraimide‐dicarboxylic acid ( I ) was synthesized starting from the ring‐opening addition of m‐aminobenzoic acid, 4,4′‐oxydiphthalic anhydride, and 2,2‐bis[4‐(4‐aminophenoxy)phenyl]propane at a 2:2:1 molar ratio in N‐methyl‐2‐pyrrolidone (NMP), followed by cyclodehydration to the diacid I . A series of soluble and light‐colored poly(amide‐imide‐imide)s ( III _a–j) was prepared by triphenyl phosphite‐activated polycondensation from I with various aromatic diamines ( II _a–j). All films cast from N,N‐dimethylacetamide (DMAc) had cutoff wavelengths shorter than 390 nm (374–390 nm) and b* values between 25.26 and 43.61; these polymers were much lighter in color than the alternating trimellitimide series. All of the polymers were readily soluble in a variety of organic solvents such as NMP, DMAc, N,N‐dimethylformamide, dimethyl sulfoxide, and even in less polar m‐cresol and pyridine. Polymers III _a–j afforded tough, transparent, and flexible films that had tensile strengths ranging from 96 to 118 MPa, elongations at break from 9 to 11%, and initial moduli from 2.0 to 2.5 GPa. The glass‐transition temperatures of the polymers were recorded at 240–268 °C. They had 10% weight loss at a temperature above 540 °C and left more than 55% residue even at 800 °C in nitrogen. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 707–718, 2002; DOI 10.1002/pola.10153     

Novel amorphous perfluorocopolymeric system: Copolymers of perfluoro‐2‐methylene‐1,3‐dioxolane derivatives

Perfluorotetrahydro‐2‐methylene‐furo[3,4‐d][1,3]dioxole (monomer I ) and perfluoro‐2‐methylene‐4‐methoxymethyl‐1,3‐dioxolane (monomer II ) are soluble in perfluorinated or partially fluorinated solvents and readily polymerize in solution or in bulk when initiated by a free‐radical initiator, perfluorodibenzoyl peroxide. The copolymerization parameters have been determined with in situ ¹⁹F NMR measurements. The copolymerization reactivity ratios are r _I = 1.80 and r _II = 0.80 in 1,1,2‐trichlorotrifluoroethane at 41 °C and r _I = 0.97 and r _II = 0.85 for the bulk polymerization. These data show that this copolymerization pair has a good copolymerization tendency and yields nearly ideal random copolymers. The copolymers have only one glass‐transition temperature from 101 to 168 °C, depending on the copolymer compositions. Melting endotherms have not been observed in their differential scanning calorimetry traces, and this indicates that all the copolymers with different compositions are completely amorphous. These copolymers are thermally stable (the initial decomposition temperatures are higher than 350 °C under an N₂ atmosphere) and have low refractive indices and high optical transparency from UV to near‐infrared. Copolymer films prepared by casting were flexible and tough. These properties make the copolymers ideal candidates as optical and electrical materials. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1613–1618, 2006