采用Si薄膜的光子计数成像系统性能的研究

在陶瓷基底上利用电子束蒸镀方法制备了Si薄膜,用作感应读出方式光子计数成像系统的电荷感应层,并研究了薄膜的结构特征和表面形态.X射线衍射(XRD)测试和场发射扫描电子显微镜(FESEM)图像表明,沉积的Si薄膜为无定形态,由于陶瓷晶界的存在,薄膜较粗糙.搭建了相应的实验系统,对比了采用不同厚度Si薄膜时系统的空间分辨率、计数率、脉冲高度分布曲线等,发现薄膜的厚度对探测器的计数率影响较大.此外,实验还对比了采用相同电阻值的Si薄膜和常用的Ge薄膜时系统的性能.研究表明,采用Si薄膜时系统的畸变较小、计数率高     

感应读出方式紫外光子计数成像技术的研究

搭建了感应读出方式紫外光子计数成像系统,详细介绍了该系统的组成、工作原理和分辨率性能测试.紫外光经过减光和滤光后入射微通道板,产生的光电子在微通道板内倍增后形成电子云,由呈高阻特性的半导体Ge薄膜收集后,通过电荷耦合感应到Ge膜衬底背面的位敏阳极.阳极输出的信号经过电荷灵敏前置放大器、整形放大器后由计算机进行数据采集和处理,最后得到不同位置的光子计数图像.通过分辨率板,测得了该系统分辨率为150 μm,并通过对比试验和分布式RC网络理论模型分析了Ge膜电阻及其衬底厚度对系统性能的影响.该系统在生物超微 关键词： 光子计数成像 电荷感应 Ge膜 位敏阳极     

厚度对非极性聚合物薄膜驻极体电荷储存及电荷动态特性的影响

以Du Pont公司的商用Teflon FEP A型薄膜为例，通过热脉冲技术、等温表面电位衰减测量和开路热刺激放电电流谱分析等实验结果，讨论了经常温和高温电晕充电后样品厚度对薄膜驻极体的沉积电荷密度、薄膜驻极体的内电场、体电导率以及电荷储存稳定性的影响.通过热脉冲技术组合电导率温度曲线的测量，研究了在不同温度条件下样品厚度对沉积电荷层的平均电荷重心移动的影响.结果表明：在充电参数一定的条件下，随着膜厚的降低，储存电荷密度上升，但电荷稳定性有所下降.因此，合理地调控薄膜厚度，可以有效地优化驻极体的电荷储存能 关键词： 厚度 驻极体 电荷储存能力 电荷稳定性     

硅基锗薄膜选区外延生长研究

利用超高真空化学气相沉积系统, 基于低温Ge缓冲层和选区外延技术, 在Si/SiO₂图形衬底上选择性外延生长Ge薄膜. 采用X射线衍射、扫描电镜、原子力显微镜、拉曼散射光谱等表征了其晶体质量和应变等参数随图形尺寸的变化规律. 测试结果显示, 位错密度随着图形衬底外延窗口的尺寸减小而减少, Ge层中的张应变随窗口尺寸的增大先增大而后趋于稳定. 其原因是选区外延Ge在图形边界形成了(113)面, 减小了材料系统的应变能, 而单位体积应变能随窗口尺寸的增加而减少; 选区外延厚度为380 nm的Ge薄膜X射线衍射曲线半高宽为678", 表面粗糙度为0.2 nm, 表明选区生长的Ge材料具有良好的晶体质量, 有望应用于Si基光电集成.     

椭偏精确测定透明衬底上吸收薄膜的厚度及光学常数

椭偏仪难以精确测量透明衬底上吸收薄膜光学常数的原因:1)衬底的背面反射光为非相干光, 它的存在会极大的增加拟合难度; 2)衬底光学常数(折射率和消光系数)的差异会影响测量的准确性, 而且会在吸收薄膜的光学常数中表现出来, 需要单独测量其光学常数; 3)厚度与光学常数之间呈现强烈的关联性. 针对以上三个问题, 选择石英玻璃、载玻片、盖玻片和普通浮法玻璃作为研究对象. 采用折射率匹配法消除上述衬底背面反射光的影响. 结果显示, 折射率匹配法能够有效消除折射率在1.43-1.64、波长范围为190-1700 nm波段的石英、浮法玻璃等透明衬底的背面反射光. 之后, 通过拟合椭偏参数ψ和垂直入射时的透过率T₀ 分别得到以上衬底的折射率和消光系数. 拟合得到的结果与文献报道的趋势一致. 最后, 采用椭偏参数和透过率同时拟合的方法(SE+T法)得到类金刚石薄膜(沉积在石英玻璃上)和非晶硅薄膜(沉积在载玻片、盖玻片上)光学常数和厚度的准确解.     

La0.67Ca0.33MnO3薄膜中的各向异性应变与电荷有序

本文采用脉冲激光沉积法在NdGaO3(001)单晶衬底上制备了一系列的La0.67Ca0.33MnO3薄膜,实验主要研究了薄膜的输运性质.La0.67Ca0.33sMnO3块材是铁磁金属基态,而La0.67Ca0.33MnO3/NdGaO3(001)薄膜由于各向异性应变的存在,可以观测到电荷有序绝缘相的出现.薄膜样品表...     

用粉末靶在玻璃和PI衬底上制备AZO/Ag/AZO薄膜

室温下在玻璃和聚酰亚胺两种不同衬底上, 采用射频磁控溅射法溅射掺铝氧化锌(AZO)粉末靶和固体Ag靶, 制备了两组AZO/Ag/AZO 3层透明导电薄膜, 研究了AZO层厚度对不同衬底3层膜结构和光电性能的影响.结果表明:不同衬底的两组AZO/Ag/AZO薄膜均为多晶膜.当Ag层厚度不变时, 随着AZO层厚度的增加, 两组薄膜电学性能变化不大, 透射峰向长波方向移动.玻璃和PI衬底上制备的AZO(30 nm)/Ag(14 nm)/AZO(30 nm)薄膜, 在550 nm处的透光率分别为85%和70%, 方块电阻分别为2.6 Ω/□和4.6 Ω/□.     

΢�����ӻ�������������廯ѧ����������Ʊ��ྦྷ�象Ĥ

利用微波电子回旋共振等离子体增强型化学气相沉积(ECR-PECVD)采用一步法直接在K9玻璃上低温沉积制备了多晶硅薄膜.研究了不同实验参数对薄膜沉积的影响,采用X射线衍射(XRD)、拉曼光谱、扫描电子显微镜(SEM)等实验分析方法对不同条件下制备的样品进行了晶体结构和表面形貌分析,并讨论了多晶硅薄膜沉积的最佳条件.实验结果表明,玻璃衬底上多晶硅薄膜呈柱状生长,并有一定厚度的非晶孵化层;较高氢气比例和衬底温度有利于结晶,薄膜的结晶率达到了62％;晶粒团簇的最大尺寸约为500nm.     

氧压强对Ga掺杂ZnO薄膜光电性质的影响

本文采用脉冲激光沉积(PLD)法在单晶硅(111)和石英玻璃衬底上制备了Ga掺杂ZnO(GZO)纳米薄膜,研究了氧压强对薄膜质量和光电性质的影响.采用XRD和SEM对薄膜的晶体结构和表面形貌进行了表征,结果表明纳米薄膜的平均粒径尺寸可以通过调整氧压强来控制,当氧压强为0.01 Pa时,薄膜的结晶质量最好.PL谱分析结果...     

厚度依赖的La_(0.33)Pr_(0.34)Ca_(0.33)MnO_3的磁学性质北大核心CSCD

采用激光脉冲沉积(PLD)方法,在LaAlO3(001)衬底上外延生长了不同厚度的La0.33Pr0.34Ca0.33MnO3薄膜,并研究了薄膜晶格常数及居里温度随薄膜厚度的变化行为.XRD表征结果表明,随着薄膜厚度的增加,LPCMO的c轴长度逐渐减小,反映了衬底对薄膜的应力作用.薄膜磁矩随温度变化的测量结果说明,随着薄膜厚度的减小,TC及TB向低温移动,反映了薄膜厚度或者衬底应力作用对LPCMO磁性的直接影响.     

The comparison between CdS thin films grown on Si(111) substrate and quartz substrate by femtosecond pulsed laser deposition

Two kinds of cadmium sulfate (CdS) thin films have been grown at 600 °C onto Si(111) and quartz substrates using femtosecond pulsed laser deposition (PLD). The influence of substrates on the structural and optical properties of the CdS thin films grown by femtosecond pulsed laser deposition have been studied. The CdS thin films were characterized by X-ray diffraction (XRD), atomic force microscopy (AFM), scanning electron microscopy (SEM), photoluminescence (PL) and Raman spectroscopy. Although CdS thin films deposited both on Si(111) and quartz substrates were polycrystalline and hexagonal as shown by the XRD , SEM and AFM results, the crystalline quality and optical properties were found to be different. The size of the grains for the CdS thin film grown on Si(111) substrate were observed to be larger than that of the CdS thin film grown on quartz substrate, and there is more microcrystalline perpendicularity of c-axis for the film deposited on the quartz substrate than that for the films deposited on the Si substrate. In addition, in the PL spectra, the excitonic peak is more intense and resolved for CdS film deposited on quartz than that for the CdS film deposited on Si(111) substrate. The LO and TO Raman peaks in the CdS films grown on Si(111) substrate and quartz substrate are different, which is due to higher stress and bigger grain size in the CdS film grown on Si(111) substrate, than that of the CdS film grown on the amorphous quartz substrate. All this suggests that the substrates have a significant effect on the structural and optical properties of thin CdS films. PACS 81.15.Fg; 81.05.Ea; 78.20.-e; 78.67.-n; 42.62.-b     

Ge nanoclusters in PECVD-deposited glass after heat treatment and electron-beam irradiation

This paper reports the formation of Ge nanoclusters in silica glass thin films deposited by plasma-enhanced chemical vapor deposition (PECVD). We studied the samples by transmission electron microscopy (TEM) and Raman spectroscopy after annealing. TEM investigation shows that the Ge nanoclusters at two areas were formed by different mechanisms. The Ge nanoclusters formed in a single row along the interface of a silicon substrate and the silica glass film by annealing during high-temperature heat treatment. Ge nanoclusters did not initially form in the bulk of the film but could be subsequently formed by the electron-beam irradiation. The interface between the silicon substrate and the silica glass film was investigated by Raman spectroscopy. The shift of the Raman peaks around 286.8 cm^-1 and 495 cm^-1 suggests that the interface is a Si_1-xGe_x alloy film and that the composition x varies along the film growth direction. PACS 81.07.Bc; 78.66.Jg; 42.65.Wi     

Deposition of carbon films using close space sublimation

Carbon films are fabricated for the first time using an inexpensive and ecologically safe modified method of close space sublimation at atmospheric pressure. They are deposited onto quartz, glass, glass ceramic (Pyroceram), and silicon substrates. The main properties of the films (such as the growth rate, morphology and structure, optical properties, the dependences of these properties on the deposition temperature and the substrate material) are studied by X-ray diffraction, atomic force microscopy, multiangular ellipsometry, and the measurement of transmission and reflectance spectra in the visible and near ultraviolet regions. The growth rate is 5 nm/min at a film nucleation temperature of 800°C. The film thickness varies from 0.2 to 2.2 μm, and the minimum surface roughness is 0.5 nm. The refractive indices of the films range from 1.3 to 1.8 depending on the growth and subsequent heat treatment conditions. The optical energy gap is 5.4 eV.     

Dependence of photoconductivity on the crystallite orientations and porosity of polycrystalline ZnO films

Hexagonal ZnO films deposited on quartz glass, sapphire and glass substrates by sol–gel coating are found to be randomly oriented; maximum randomness is found in the film on quartz glass substrate. All the films are ultra-violet (UV) sensitive at around 360 nm sensitivity being maximum for the film with maximum randomness in the crystallite orientations. The film on quartz showed the lowest dark current and maximum photoresponse, which is related to the lowering of the barrier heights, introduced by the adsorbed oxygen at the grain boundaries. Faster decay in photocurrent is observed for the film deposited on glass, which is attributed due to the smaller crystallite sizes with porous microstructure of the film. PACS 73.61.Ga; 68.55.Jk; 73.50.Pz     

石英衬底上GaN薄膜沉积及其光学性能的研究

GaN薄膜材料广泛应用于发光二极管(LED),激光二极管(LD)等光电器件。但是GaN基器件的制备与应用以及器件推广很大一部分取决于其器件的价格,常用的方式是在单晶蓝宝石衬底上沉积制备GaN薄膜样品,单晶蓝宝石衬底晶向择优,可以制备出高质量的GaN薄膜样品,但是单晶蓝宝石衬底价格昂贵,一定程度上限制了其GaN基器件推广使用。如何在廉价衬底上直接沉积高质量的GaN薄膜,满足器件的要求成为研究热点。石英玻璃价格廉价,但是属于非晶体,没有择优晶向取向,很难制备出高质量薄膜样品。本研究采用等离子体增强金属有机物化学气相沉积系统在非晶普通石英衬底上改变氮气反应源流量低温制备GaN薄膜材料。制备之后采用反射高能电子衍射谱、X射线衍射光谱、室温透射光谱和光致光谱对制备的薄膜进行系统的测试分析。其结果表明：在氮气流量适当的沉积参数条件下,所制备的薄膜具有高C轴的择优取向,良好的结晶质量以及优异的光学性能。     

不同衬底和CdCl2退火对磁控溅射CdS薄膜性能的影响

在科宁7059玻璃, FTO, ITO, AZO四种衬底上磁控溅射CdS薄膜, 并在CdCl₂+干燥空气380 ℃退火, 分别研究了不同衬底和退火工艺对CdS薄膜形貌、结构和光学性能的影响. 扫描电子显微镜形貌表明: 不同衬底原位溅射CdS薄膜的形貌不同, 退火后相应CdS薄膜的晶粒度和表面粗糙度明显增大. XRD衍射图谱表明: 不同衬底原位溅射和退火CdS薄膜均为六角相和立方相的混相结构, 退火前后科宁7059玻璃, FTO, AZO衬底上CdS薄膜有 H(002)/C(111) 最强衍射峰, ITO衬底原位溅射CdS薄膜没有明显的最强衍射峰, 退火后出现 H(002)/(111) 最强衍射峰. 紫外-可见分光光度计分析表明: AZO, FTO, ITO, 科宁7059玻璃衬底CdS薄膜的可见光平均透过率依次减小, 退火后相应衬底CdS薄膜的可见光平均透过率增大, 光学吸收系数降低; 退火显著增大了不同衬底CdS薄膜的光学带隙. 分析得出: 上述结果是由于不同衬底类型和退火工艺对CdS多晶薄膜的形貌、结构和带尾态掺杂浓度改变的结果. 关键词： CdS薄膜 磁控溅射 退火再结晶 带尾态     

Influence of size effect and sputtering conditions on the crystallinity and optical properties of ZnO thin films

The effects of the thickness variation, substrate type and annealing on the crystallinity parameters, luminescent and optical properties of the zinc oxide (ZnO) thin films were reported. The thin films were deposited on the glass and the amorphous quartz substrates by the standard RF-magnetron sputtering method using ZnO targets in the argon atmosphere. It has been found that the films deposited on the glass substrate manifest a clear size effect. Both the structural and the optical parameters show clearly minima on their thickness dependences. It has been shown that annealing of the comparatively thick ZnO films leads to increase of the crystallite sizes that are followed by a considerable rise of the cathodoluminescence intensity. The corresponding model of the crystallite growth is proposed.     

GeC薄膜的射频磁控反应溅射制备及性质

用射频磁控反应溅射法在ZnS衬底上制备了GeC薄膜,研究了工艺参数对Ge靶溅射及GeC薄膜红外透射性能的影响.衬底温度较低时GeC薄膜中含有H,形成了CH₂,CH₃,Ge-CH₃等,使薄膜产生红外吸收;随衬底温度升高,薄膜红外吸收明显减小.靶基距、射频功率、Ar:CH₄气体流量比、总气压对靶面中毒及溅射影响较大,但对GeC薄膜红外吸收影响较小.靶面中毒严重时,所制备无氢GeC薄膜附着性能差,随靶中毒减弱薄膜附着性能变好.优化工艺后,在ZnS衬底上制备了附着性能良好的无氢GeC薄膜,其折射率约为1.78,薄膜中C的含量比Ge的大,二者主要形成了C—Ge键.所制备的GeC/GaP红外增透保护膜系对ZnS衬底有良好的增透效果. 关键词： GeC薄膜 红外透射光谱 射频磁控溅射 XPS