超高效液相色谱-质谱法测定油脂中的10种抗氧化剂

对油脂中的没食子酸丙酯(PG),没食子酸辛酯(OG)、2,4,5-三羟基苯丁酮(THBP)、叔丁基对苯二酚(TBHQ)、叔丁基对羟基茴香醚(BHA)、2,6-二叔丁基对甲酚(BHT)、没食子酸十二酯(DG)、正二氢愈创酸(NDGA)、2,6-二叔丁基-4-羟甲基苯酚(HMBP)和没食子酸异戊酯(IAG)10种抗氧化剂进行了超高效液相色谱-质谱法(UPLC/MS)测定的系统研究,建立了一种简单、快速、准确测定油脂中10种抗氧化剂的测定方法。对样品中提取溶剂和提取时间的选择以及相关线性、精密度、回收率作了考察和实验。结果表明,本方法能有效提取油脂样品中的这10种抗氧化剂,并对其进行UPLC/MS分离和测定。10种抗氧化剂的平均回收率为92.56%～102.5%(n=6),相对标准偏差为0.68%～5.12%(n=6),检出限为2～10μg/L。     

超高效液相色谱-串联质谱法同时测定调味料中的17种防腐剂和抗氧化剂

建立了超高效液相色谱-串联质谱(UPLC-MS/MS)同时测定调味料中11种防腐剂和6种抗氧化剂的定性、定量分析方法。低脂肪和中等脂肪含量的调味料样品用饱和NaCl水溶液(用磷酸调pH为2～3)稀释混合均匀,然后用乙腈提取,正己烷液-液萃取净化(中等脂肪含量的样品提取液还需经C8固相萃取柱进一步的净化处理);脂肪含量高的样品先用正己烷稀释,再用饱和NaCl水溶液(用磷酸调pH为2～3)溶解样品,然后用乙腈提取,提取液进一步经C8固相萃取柱净化处理。提取液经C18反相色谱柱(150 mm×2.1 mm, 1.7μm)分离,流动相为20 mmol/L乙酸铵水溶液和乙腈,梯度洗脱,以电喷雾离子源负离子多反应监测(MRM)模式进行MS/MS检测。17种分析物在线性范围内具有较好的线性关系,相关系数r≥0.9955,其定量限(LOQ,信噪比为10)为0.05～5 mg/kg;空白样品中的添加回收率为79.7%～118%,精密度(以相对标准偏差计)为0.57%～13.1%。该方法适用于调味品中防腐剂和抗氧化剂的检测。     

气相色谱-质谱法测定化妆品中多种防腐剂

采用超声抽提法对化妆品中的苯甲醇、3-甲基-4-异丙基苯酚、对羟基苯甲酸丁酯和2-苄基-4-氯酚等18种防腐剂进行了气相色谱-质谱法(GC-MS)测定的研究。建立了一种简单、快速、准确测定化妆品中各种防腐剂的测定方法。进行了样品提取溶剂和超声提取时间选择以及线性、回收率、精密度试验。结果表明,该方法能够有效地提取化妆品(口红和香波)中的18种防腐剂,并可对其进行GC-MS分离和鉴定。18种防腐剂的平均回收率为91.66%-100.6%(n=7),相对标准偏差为0.46%-6.23%(n=7),最低检测限为     

超高效液相色谱法同时测定食品塑料包装材料中的紫外吸收剂和抗氧化剂

超声萃取结合超高效液相色谱(UPLC)技术,建立了食品塑料包装材料中14种紫外吸收剂及抗氧化剂(UV-0,UV-9,UV-71,UV-329,UV-326,UV-327,UV-234,UV-360,抗氧化剂2246,抗氧化剂425,TH-1790,抗氧化剂3114,抗氧化剂1010和抗氧化剂1076)的高通量检测方法。样品经三氯甲烷-甲醇超声提取,C18色谱柱分离后,乙腈和0.1%甲酸水为流动相梯度洗脱,二极管阵列检测器测定。14种物质在一定的浓度范围内线性关系良好,相关系数(r2)均不低于0.999 2,方法定量下限(S/N=10)为8.0~33.0 mg/kg,平均回收率为83.6%~116.2%,相对标准偏差(RSD,n=6)为1.3%~9.5%。方法具有前处理简单、净化效果好等特点,适用于食品塑料包装中14种紫外吸收剂及抗氧化剂的同时测定。     

气相色谱-质谱法同时测定果蔬清洗剂中12种防腐剂和抗氧化剂

建立了气相色谱-质谱同时检测果蔬清洗剂中12种防腐剂和抗氧化剂的方法。果蔬清洗剂样品先加入乙醇,经旋转蒸发除去样品中的水分,然后用正己烷饱和的乙腈溶液提取,饱和氯化钠溶液洗涤净化,净化后的样品溶液浓缩后用乙腈定容。被测组分经HP-5MS UI石英毛细管色谱柱（30 m×0.25 mm×0.25 μm）分离后在选择离子监测模式下测定。12种防腐剂和抗氧化剂在0.1~10 mg/L范围内线性关系良好,相关系数（r²）>0.999;检出限和定量限分别为0.010~0.030 mg/kg和0.030~0.090 mg/kg。按照建立的方法进行0.2、2.0和10 mg/kg 3个添加水平的加标回收试验,回收率为68.3%~115.3%,相对标准偏差为3.1%~11.3%。该法灵敏度高,定性准确,前处理净化效果好,适用于果蔬清洗剂中防腐剂和抗氧化剂的检测。     

高效液相色谱测定食品中的7种抗氧化剂

建立了高效液相色谱同时定量测定食品中叔丁基对羟基茴香醚、2,6-二叔丁基对甲酚、特丁基对苯二酚、没食子酸丙酯、没食子酸辛酯、没食子酸异戊酯和没食子酸月桂酯7种抗氧化剂的分析方法.液态油脂样品经甲醇反复提取后氮气吹干,5 mL甲醇定容;固体样品使用正己烷提取,再用乙腈反萃取多次,氮气吹干,5 mL甲醇定容.提取液经Eclipse XDB-C18色谱柱(250 mm x4.6 mm,5μm)分离,以1.5％乙酸-甲醇为流动相,梯度洗脱.用二极管阵列检测器(PDA)进行检测,结合保留时间和紫外光谱进行定性分析,定量检测波长280 nm.7种抗氧化剂在1～100 mg/L范围内具有较好的线性关系,相关系数r2＞0.999,定量下限(LOQ,S/N=10)为1.0～1.5 mg/kg;空白样品的加标回收率为79％～ 101％,相对标准偏差均低于7％.将该方法应用于食品中抗氧化剂的检测,从成品植物油、坚果等食品中检出抗氧化剂的残留.该方法准确快速、灵敏度高,满足食品中添加剂的检测要求.     

固相萃取-气相色谱-质谱法测定木制家具中氯酚类及菊酯类防腐剂

建立了固相萃取-气相色谱-质谱(SPE-GC-MS)检测含氯酚类化合物(2,4-二氯苯酚、2,4,6-三氯苯酚、2,4,5-三氯苯酚、2,3,4,6-四氯苯酚、五氯苯酚、林丹)和菊酯类化合物(氯菊酯、氟氯氰菊酯、氯氰菊酯、溴氰菊酯)等10种木材防腐剂的方法。对家具样品采用超声萃取法、以甲醇为提取剂在室温下反复提取2次,提取液经浓缩后,加入碳酸钾和乙酰酐衍生化,将衍生化后的溶液通过Oasis HLB固相萃取柱净化,用乙酸乙酯洗脱并收集检测。采用该方法实现了家具中10种木材防腐剂的分离检测,该方法中氯酚类防腐剂定量限为1 mg/kg、菊酯类防腐剂定量限为5 mg/kg,平均回收率为76.0%～108.8%。应用该方法对市场上销售的木制家具进行了检测,在部分家具中检出含有少量林丹。实验结果证明,该方法准确、灵敏,可有效地应用于木制家具中防腐剂的实际检验工作中。     

气相色谱-质谱法测定化妆品中10种防腐剂

采用气相色谱-质谱法(GC-MS)同时测定化妆品中10种防腐剂含量。样品经甲醇超声提取,无水硫酸钠脱水后过滤进样检测。采用Agilent HP-5MS毛细管色谱柱(30m×0.25mm,0.25μm)分离,程序升温,分流进样进行测定。结果表明:17min内即可完成10种防腐剂的测定,各防腐剂的质量浓度均在5.00~100mg·L-1范围内与峰面积呈线性关系,方法的检出限(3S/N)为0.30~0.70ng。方法用于化妆品测定,加标回收率在96.5%~105%之间,测定值的相对标准偏差(n=6)在0.66%~3.2%之间。     

高效液相色谱-电感耦合等离子体质谱法同时测定化妆品中5种含溴防腐剂

建立了同时测定化妆品中苯扎溴铵、2-溴-2-硝基-1,3-丙二醇、5-溴-5-硝基-1,3-二■烷、甲基二溴戊二腈、溴氯芬5种含溴防腐剂的高效液相色谱-电感耦合等离子体质谱法(HPLC-ICP-MS)。样品经含0.1%甲酸的甲醇溶液超声提取后,采用Agilent Eclipse-C_(18)(150 mm×4.6 mm,5μm)色谱柱分离,以0.1%甲酸-甲醇为流动相进行梯度洗脱,ICP-MS测定组分中的~(79)Br,以保留时间定性,外标法定量。5种含溴防腐剂均在0.5～100 mg/L范围内线性关系良好(r0.999),检出限为1.5～3.0μg/g,不同基质化妆品中的回收率为91.2%～108%,相对标准偏差(n=6)为1.3%～4.2%。该方法快速、准确、灵敏、专属性强,适用于化妆品中5种含溴防腐剂的定性定量分析。     

高效液相色谱梯度洗脱同时测定化妆品中防腐剂、抗氧化剂和杀菌剂

建立了一种灵敏、快速的高效液相色谱梯度洗脱同时测定化妆品中防腐剂、抗氧化剂和杀菌剂的方法。采用C8柱,以甲醇和水为流动相梯度洗脱。在检测波长273nm用二极管阵列检测器,17min内可将4种防腐剂、2种抗氧化剂和2种杀菌剂分离测定。方法快速准确,用于实际样品的测定。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.