SSC-LINAC重离子RFQ动力学模拟与研究

采用多粒子跟踪程序BEAMPATH 对SSC-LINAC 重离子RFQ 直线加速器进行动力学模拟,分别对RFQ 的接受度、高频特性、束流稳定性、空间电荷效应等进行了分析。该RFQ具有很大的纵向接受度,有利于束流在RFQ中的传输;高频特性研究表明,翼间电压设定在理论值以上时,该RFQ都能保持较好的束流特性;束流稳定性分析结果表明,该RFQ具有很大的束流失配容忍度;空间电荷效应研究表明,当束流强度低于0.5 mA时,束流传输不受影响。综合研究结果表明,53.667 MHz重离子RFQ具有较好的动力学特性,满足SSC-LINAC直线加速器的设计要求。The RFQ beam dynamics of a heavy ion linac was investigated in this paper and the BEAMPATH code was employed in this study. The main research was focused on the beam performances depending on longitudinal acceptance, RF properties, beam instability and space charge effect. The RFQ has large longitudinal acceptance in design, which brings the beam performances well. In the RF parameter study, the beam can keep good transmission in the acceleration even the vane voltage is larger than the theoretical value. It is also shown that the RFQ has a large robustness for the mismatch of the input beam by the analysis of the beam instability.Furthermore, the beam evolution is independent on the space charge effect when the beam current is less than 0.5 emA. The preliminary analysis of the beam dynamics shows that the 53.667 MHz heavy ion RFQ has a promising performance, which meets the requirements of SSC-LINAC.     

IH型漂移管直线加速器的束流动力学研究（英文）

为了提高兰州重离子加速器冷却储存环（HIRFL-CSR）的运行效率、改善加速器输出束流品质,并实现几个加速装置分时供束,提高整个重离子加速装置的利用率,特为（HIRFL-CSR）增建一台新的注入器--CSRLINAC。在108.48 MHz的RFQ之后的CSR-LINAC主加速段,主要由一台108.48 MHz和两台216.96 MHz的IH型漂移管直线加速器组成,用于加速荷质比为1/8.5~1/3之间的重离子,其最大的束流流强为3 mA,并将粒子从0.3 MeV/u加速到3.71 MeV/u。运用KONUS动力学原理,在满足设计指标的情况下,首先利用TraceWin程序进行中能束线MEBT设计,后针对高频腔体设计和束流匹配的基本参数的系列讨论,特别是对CSR-LINAC的中能束流匹配线、参数选择和IH型KONUS结构的漂移管直线加速器进行设计模拟优化。最终得出,在保证腔体设计指标和95.3%的传输效率的情况下,该紧凑型直线加速结构经过三个腔体的加速后,束流的纵向归一化均方根发射度增长仅有25%;同时发现,当流强达到3 mA时,存在空间电荷效应,导致其纵向相宽增长约25%,最大横向包络也存在16.5%的涨落。In order to improve the operation efficiency of the Cooling Storage Ring of Heavy Ion Research Facility in Lanzhou (HIRFL-CSR), a heavy ion linac (linear accelerator) was proposed and designed as a new injector for HIRFL-CSR. Following the 108.48 MHz Radio-Frequency Quadrupole (RFQ), three tanks in total with Interdigital H-mode drift tube linac (IH-DTL) structure are installed to boost the beam energy from 0.3 to 3.71 MeV/u, and the beam current of ions with charge-to-mass ratio from 1/8.5 to 1/3 can reach to 3 mA. The first tank operatesat the same frequency as the RFQ, and the rest two operate at 216.96 MHz. The “Combined Zero-Degree Synchronous Particle Structure” (KONUS) beam dynamics was used in the beam dynamics design. The overview of the physics design on the main accelerating components, including RF design and beam dynamics design are introduced in this paper. The optimized structure design, fabrication status and simulation results are presented in this contribution. It shows that under the condition of assurance of 95.3% transmission efficiency, the normalized rms emittance is about 25%. When the beam current is up to 3 mA, owing to the space charge effect, the increase of longitudinal phase spread and transverse envelope are about 25% and 16.3%, respectively.     

电子束在α-磁铁模型中传输模拟与优化

在电子直线加速器设计中,α-磁铁通常被用来压缩脉冲长度,采用热阴极微波电子枪和α-磁铁相结合的设计,可以获得皮秒或亚皮秒量级脉冲长度的电子束。电子束在α-磁铁中的传输过程较为复杂,相关文献介绍的研究成果均是基于理想模型,且有镜板开孔的α-磁铁的束流传输研究,对α-磁铁的使用具有重要的指导作用。本文首先简单介绍了用于高能电子成像装置的α-磁铁模型的设计,对电子束在理想模型与α-磁铁模型中传输模拟结果进行对比分析,验证了所构建模型可以有效地实现脉冲纵向压缩的结论。此外,对以优化角度进入α-磁铁和在空间电荷效应影响下的单束团及多束团束流动力学模拟结果进行了讨论,提出通过减小入射角度来补偿α-磁铁镜板上的束流进出孔对束流传输影响的方案。通过在α-磁铁与电子枪之间增加四极磁铁组,优化了束流发射度和束团尺寸。     

A simulation study of Tsinghua Thomson scattering X-ray source

Thomson scattering X-ray sources are compact and a?ordable facilities that produce short duration, high brightness X-ray pulses enabling new experimental capacities in ultra-fast science studies, and also medical and industrial applications. Such a facility has been built at the Accelerator Laboratory of Tsinghua University, and upgrade is in progress. In this paper, we present a proposed layout of the upgrade with design parameters by simulation, aiming at high X-ray pulses flux and brightness, and also enabling advanced dynamics studies and applications of the electron beam. Design and construction status of main subsystems are also presented.     

Preliminary design and simulation of a 162.5 MHz high-intensity proton RFQ for an accelerator driven system

A new procedure for the design and simulation of a Radio Frequency Quadrupole (RFQ) accelerator has been developed at the Argonne National Laboratory. This procedure is integrated with the beam dynamics design code DESRFQ and the simulation code TRACK, which are based on three-dimensional field calculations and the particle-in-cell mode beam dynamics simulations. This procedure has been applied to the development of a 162.5 MHz CW RFQ which is capable of delivering a 10 mA proton beam for the Accelerator Driven System (ADS) of the CAS. The simulation results show that this RFQ structure is characterized by the stable values of the beam acceleration efficiency for both the zero current beam and space charge dominated beam. For an average beam current of 10 mA, there is no transverse rms emittance growth, the longitudinal rms emittance at the exit of RFQ is low enough and there is no halo formation. The beam accelerated in the RFQ could be accepted easily and smoothly by the following super-conducting linear accelerator.     

强流RFQ加速器的匹配设计方法研究

模拟计算和束流实验证明不匹配是直线加速器中强流束产生束晕的直接原因. 束晕的产生将导致束流品质下降和束流丢失, 也使得不匹配成为引起束流丢失的主要原因. 为了提高强流RFQ加速器中束流的传输品质和提高传输效率, 在分析了RFQ加速器中束流不匹配的原因之后, 提出了基于常规四部曲方法的匹配动力学设计方法. 该设计方法可以有效地抑制发射度增长和提高束流的传输效率.     

Preliminary design and simulation of a 162.5 MHz high- intensity proton RFQ for an accelerator driven system

A new procedure for the design and simulation of a Radio Frequency Quadrupole (RFQ) accelerator has been developed at the Argonne National Laboratory. This procedure is integrated with the beam dynamics design code DESRFQ and the simulation code TRACK, which are based on three-dimensional field calculations and the particle-in-cell mode beam dynamics simulations. This procedure has been applied to the development of a 162.5 MHz CW RFQ which is capable of delivering a 10 mA proton beam for the Accelerator Driven System (ADS) of the CAS. The simulation results show that this RFQ structure is characterized by the stable values of the beam acceleration efficiency for both the zero current beam and space charge dominated beam. For an average beam current of 10 mA, there is no transverse rms emittance growth, the longitudinal rms emittance at the exit of RFQ is low enough and there is no halo formation. The beam accelerated in the RFQ could be accepted easily and smoothly by the following super-conducting linear accelerator.     

Thermal buckling and natural vibration of the beam with an axial stick–slip–stop boundary

As a first attempt to study the dynamics of a heated structure with complicated boundaries, this paper deals with the thermal buckling and the natural vibration of a simply supported slender beam, which is subject to a uniformly distributed heating and has a frictional sliding end within a clearance. This sliding end is initially at a stick status under the friction force, but may be slightly slipping due to the thermal expansion of the beam until the sliding end contacts a stop, i.e., the bound of the clearance. The material properties of the beam are temperature-independent for low temperature, but temperature-dependent for high temperature. For each case, the analytic solutions for the critical buckling temperature and the natural frequencies of the heated beam are derived first. Then, discussions are made to reveal the effects of beam parameters, such as the ratio of beam length to beam thickness, the ratio of clearance to beam length and the temperature-dependent material properties, on the critical buckling temperature and the fundamental natural frequency of the heated beam. The study shows that both friction force and clearance have significant influences on the critical buckling temperature and the fundamental natural frequency of the beam. When the friction force is not very large, the clearance can greatly increase the critical buckling temperature. These conclusions enable one to properly design the stick–slip–stop boundary so as to improve the mechanical performance of the beam in thermal environments.     

Beam dynamics and RF design of trapezoidal IH-RFQ with low energy spread

Beam dynamics and RF design have been performed of a new type trapezoidal IH-RFQ operating at 104 MHz for acceleration of ¹⁴C⁺ in the framework of RFQ based ¹⁴C AMS facility at Peking University. Low energy spread RFQ beam dynamics design was approached by the method of internal discrete bunching. ¹⁴C⁺ will be accelerated from 40 keV to 500 keV with the length of about 1.1 m. The designed transmission efficiency is better than 95% and the energy spread is as low as 0.6%. Combining the beam dynamics design, a trapezoidal IH-RFQ structure was proposed, which can be cooled more easily and has better mechanical performance than traditional RFQ. Electromagnetic field distribution was simulated by using CST Microwave Studio (MWS). The specific shunt impedance and the quality factor were optimized primarily.     

Beam dynamics studies in the driver LINAC pre-stripper section of the RIA facility

The RIA facility driver LINAC consists of about 400 superconducting (SC) independently phased rf cavities. The LINAC is designed to accelerate simultaneously several charge-state beams to generate as much as 400 kW of uranium beam power. The LINAC beam dynamics is most sensitive to the focusing and accelerating structure parameters of the pre-stripper section, where the uranium beam is accelerated from 0.17 keV/u to 9.4 MeV/u. This section is designed to accept and accelerate two charge states (28 and 29) of uranium beam from an ECR ion source. The pre-stripper section must be designed to minimize the beam emittance distortion of this two-charge-state beam. In particular, the inter-cryostat spaces must be minimized and beam parameters near transitions of the accelerating and focusing lattices must be matched carefully. Several sources of possible effective emittance growth are considered in the design of the pre-stripper section and a tolerance budget is established. Numerical beam dynamics studies include realistic electric and magnetic three-dimensional field distributions in the SC rf cavities and SC solenoids. Error effects in the longitudinal beam parameters are studied.     

Optical design and optimization of light emitting diode automotive head light with digital micromirror device light emitting diode

This research proposes a new method for light emitting diode automotive headlight design with digital micromirror device (DMD). The optical design is advanced because of the following features. First, this optical design controls the angle of light pattern without light masking so as to achieve much higher light efficiency compared with traditional optical design for headlight systems. Second, in view of the tendency that the advanced light emitting diode automobile headlight is designed to be a low beam light module and a high beam light still needs an auxiliary lighting system, the optical system designed in this research, mainly adopting DMD module as high/low beam light switch, can switch on and off both the high and low beam lights. Because DMDs function of accepting a bidimensional image, high/low beam light patterns can be determined by DMD. Third, a light pattern will be created and compensated simultaneously by DMD, which might replace mechanical adaptive front-lighting system in the future because DMD takes advantage of fast response and simultaneous compensation. Fourth, a design using a multiple reflection curved mirror is employed in this research to adjust light energy distribution; therefore, the articulation of the light pattern can be enhanced. For this method, experimental results of light efficiency are up to 85%, which is superior to current products in the market.     

Simulation of a Radio-Frequency Photogun for the Generation of Ultrashort Beams

A radio-frequency photogun for the generation of ultrashort electron beams to be used in fast electron diffractoscopy, wakefield acceleration experiments, and the design of accelerating structures of the millimeter range is modeled. The beam parameters at the photogun output needed for each type of experiment are determined. The general outline of the photogun is given, its electrodynamic parameters are calculated, and the accelerating field distribution is obtained. The particle dynamics is analyzed in the context of the required output beam parameters. The optimal initial beam characteristics and field amplitudes are chosen. A conclusion is made regarding the obtained beam parameters.     

BPL－RFQ加速器束流动力学设计研究

描述北京质子直线加速器ＲＦＱ的参数选择及束流动力学设计研究，给出了ＢＰＬ－ＲＦＱ的主要参数．     

Beam dynamics study of RFQ for CADS with a 3D space-charge-effect

The ADS (accelerator driven subcritical system) project was proposed by the Chinese Academy of Sciences. The initial proton beams delivered from an electron cyclotron resonance ion source can be effectively accelerated by 162.5 MHz 4.2 m long room temperature radio-frequency-quadrupoles (RFQ) operating in CW mode. To test the feasibility of this physical design, a new Fortran code for RFQ beam dynamics study, which is space charge dominated, was developed. This program is based on Particle-In-Cell (PIC) technique in the time domain. Using the RFQ structure designed for the CADS project, the beam dynamics behavior is performed. The well-known simulation code TRACK is used for benchmarks. The results given by these two codes show good agreements. Numerical techniques as well as the results of beam dynamics studies are presented in this paper.     

Design of a 10 MeV normal conducting CW proton linac based on equidistant multi-gap CH cavities

Continuous wave(CW) high current proton linacs have wide applications as the front end of high power proton machines. The low energy part of such a linac is the most difficult and there is currently no widely accepted solution. Based on the analysis of the focusing properties of the CW low energy proton linac, a 10 Me V low energy normal conducting proton linac based on equidistant seven-gap Cross-bar H-type(CH) cavities is proposed. The linac is composed of ten 7-gap CH cavities and the transverse focusing is maintained by quadrupole doublets located between the cavities. The total length of the linac is less than 6 meters and the average acceleration gradient is about1.2 Me V/m. The electromagnetic properties of the cavities are investigated by Microwave Studio. At the nominal acceleration gradient the maximum surface electric field in the cavities is less than 1.3 times the Kilpatrick limit,and the Ohmic loss of each cavity is less than 35 k W. Multi-particle beam dynamics simulations are performed with Tracewin code, and the results show that the beam dynamics of the linac are quite stable, the linac has the capability to accelerate up to 30 m A beam with acceptable dynamics behavior.     

Physics design of CYCAIE-100

The design and construction of Beijing Radioactive Ion-beam Facility (BRIF) was started at China Institute of Atomic Energy -CIAE) in 2004. In this project, a 100 MeV high intensity cyclotron, CYCIAE100, is selected as a driving accelerator for radioactive ion beam production. It will provide a proton beam of 75—100 MeV with an intensity of 200—500 μA. The scheme adopted in this design, i.e., stripping the accelerated H-, makes the structure more compact and construction cost much lower. At present, the design for each system has been accomplished. This paper depicts the basic physics design of the machine, including its major structure and parameters, beam dynamics and each relevant system, e.g. basic structure of the main magnet, numerical simulation of the RF resonant cavity, axial injection system, central region, and study on crucial physics problems concerning the extraction and beam lines. The major problems encountered during the design of CYCIAE-100 are also summarized in this paper.     

Beam dynamics studies on BEPC-Ⅱstorage rings at the commissioning stage

During the 1st and 2nd stages of the commissioning of the upgrade project of the Beijing Electron Positron Collider(BEPC Ⅱ),which started on Nov.12,2006 and Oct.24,2007,respectively,we got the luminosity one tenth of its design value,provided beams to synchrotron radiation users for about 4 months,and studied beam dynamics as well.In this paper,some beam dynamics studies on the storage rings and their preliminary results are given.     

Beam dynamics and RF design of trapezoidal IH-RFQ with low energy spread

Beam dynamics and RF design have been performed of a new type trapezoidal IH-RFQ operating at 104 MHz for acceleration of 14C+ in the framework of RFQ based 14C AMS facility at Peking University. Low energy spread RFQ beam dynamics design was approached by the method of internal discrete bunching. 14C+ will be accelerated from 40 keV to 500 keV with the length of about 1.1 m. The designed transmission efficiency is better than 95% and the energy spread is as low as 0.6%. Combining the beam dynamics design, a trapezoidal IH-RFQ structure was proposed, which can be cooled more easily and has better mechanical performance than traditional RFQ. Electromagnetic field distribution was simulated by using CST Microwave Studio (MWS). The specific shunt impedance and the quality factor were optimized primarily.     

Central region design for a 10 MeV internal ion source cyclotron

Internal ion sources are widely adopted in commercial cyclotrons used for short-life isotopes production. Without beam manipulation provided by the external beam injection line, the central region of this type of cyclotron is more sensitive and should be carefully designed. A design study and beam dynamics simulation for the central region of a 10 MeV compact cyclotron is presented. The OPERA3D/TOSCA code was used to calculate the electric field from a parameterized three dimensional （3D） central region model. With iterative structure optimizations of the central region, the beam centering and vertical focusing is well controlled, and the RF phase acceptance is around 25°. A c＋＋ code for beam simulation in the central region was developed and tested.     

an Introduction to Mebt For JKJ and Its Upgrade Design

The medium-energy beam-transport line (MEBT) plays an important role in reducing the beam loss in the Japan Proton Accelerator Research Complex (J-PARC). A MEBT was designed and constructed,with good beam matching and lower beam loss. A brief introduction to the MEBT and its beam test results are given. To further reduce the beam loss during the transient time of the chopper,a medium-energy beamtransport line with an anti-chopper has been designed. It accomplishes three tasks: matching the beam from the RFQ to the acceptance of the DTL, chopping the beam to produce gaps for injection into the rapid cycling ring which follows the linac, and returning the partially deflected beam back to the acceptance of the DTL. An RF chopper and an anti-chopper have been adopted in the beam line, and the optimization of the design of the chopper cavity is discussed. Details of the beam dynamics analysis are given.