溶胶-凝胶法制备薄膜型TiO2光催化剂

用TiCl4作原料,通过溶胶-凝胶法在单晶硅基片上制备了TiO2纳米薄膜,并用XRD,AES,XPS以及紫外反射光谱等手段,对TiO2薄膜的结构进行了研究.结果发现,TiO2薄膜以锐钛矿型晶相存在.TiO2薄膜层与硅衬底间无明显的界面扩散反应.掺杂的Pd在还原前的薄膜中以氧化态存在,还原后则以高分散的金属态存在.掺杂的Pt在还原前后均以金属态存在,但还原后产生颗粒聚集.掺杂Pd的TiO2薄膜经还原后,其紫外吸收强度明显提高,主吸收峰发生红移.     

溶胶-凝胶法制备金属铂高分散的二氧化钛薄膜

Uniform and crack free TiO 2 thin films with highly dispersed platinum were prepared from i PrOH TTIP DEA H 2O system containing H 2PtCl 6·6H 2O as metal source by sol gel method. The microstructure and morphology of the films were characterized by TEM and XRD respectively. It was found that the Pt particles dispersed in the films and had a homogeneous distribution in the shape of sphere with an average size of about 5 nm. This study also showed that the doping with few percent of Pt resulted in the formation of pure rutile phase at a temperature as low as 550 ℃, whereas the same pure phase was formed at the temperature higher than 650 ℃ in TiO 2 or Au/TiO 2 thin films.     

溶胶凝胶法制备光催化薄膜材料及其性能表征

采用溶胶凝胶法制备TiO2胶体,再采用旋涂法在玻璃基体上负载得到TiO2薄膜,并对制备的TiO2结构进行表征,以2,4二-氯苯酚为探针,考察薄膜的光催化性能。通过实验,学生基本了解溶胶-凝胶法的原理、薄膜的制备方法、光催化剂的性能表征,可以作为开放性实验。     

氮掺杂二氧化钛薄膜的光催化性能研究

采用溶胶-凝胶法制备了氮掺杂Ti O2薄膜;利用X射线光电子能谱仪、紫外-可见光谱仪表征了所制备的薄膜的化学状态和光吸收性能;并考察了可见光照射下薄膜的亲水性能和光催化性能.结果表明:N通过取代部分O的方式进入到Ti O2薄膜中,且掺杂后在可见光区的光吸收增强;最优条件下,Ti O2-xNx薄膜的接触角由31°降到12°,亲水化速度常数为0.018,可见光照射3 h,亚甲基蓝的降解率达到45%.     

溶胶-凝胶法制备稀土铽配合物掺杂的发光薄膜

采用溶胶－凝胶法原位制备了稀土配合物掺杂的发光薄膜，薄膜透明均一。结果表明用原位合成法，可以将难溶性稀土羧酸类配合物有效地掺杂到溶胶基质中，荧光光谱分析表明，所得到的薄膜材料在紫外激发下发射出铽离子的特征发射线。     

溶胶-凝胶法制备Tb-PDA/PVA薄膜及其荧光性能

采用溶胶-凝胶法制备了铽(Ⅲ)-吡啶-2,6-二羧酸/聚乙烯醇(Tb-PDA/PVA)发光薄膜,其结构经IR,差热分析,原子力显微镜及荧光光谱表征.分析结果表明:薄膜表面平整,PVA中的纳米Tb-PDA(平均粒径为90 nm)分散均匀,在270 ℃以下具有良好的热稳定性.在紫外光照射下,薄膜发出较强的绿色荧光,最大发射峰位于544 nm,归属于Tb3+的5D4→7F5跃迁.     

溶胶法制备的二氧化硅与二氧化钛复合薄膜的性能

在室温下, 采用溶胶法在玻璃基板上制备了厚度约为100 nm的均匀、透明的纳米SiO2-TiO2复合薄膜.研究了不同温度处理后薄膜的超亲水性、光催化能力等光致活性.通过XPS对薄膜表面及近表面元素的化学态的研究发现, Ti在表面及近表面不仅以Ti4＋形式存在, 也存在少量Ti3＋.紫外光照射后, 部分Ti4＋ 转变成了Ti3＋. XRD研究表明, 该薄膜中的TiO2主要以锐钛矿形式存在, 而且其晶粒大小为14～20 nm.用AFM研究了SiO2-TiO2薄膜的表面形貌及不同的温度处理对TiO2颗粒大小的影响.     

PEO掺杂氧化镍薄膜的溶胶-凝胶法制备及电致变色性能研究

以无水醋酸镍、乙醇为前驱液, 加入适量正丁醇及PEO2000等为稳定剂, 采用改进的溶胶-凝胶法制备了稳定的PEO2000纳米Ni(OH)₂复合溶胶体系, 采用旋涂法在ITO (In₂O₃∶Sn)导电玻璃上形成均匀的氧化镍薄膜. 研究了溶胶组分对成膜性能的影响, 采用TG-DSC分析、X射线衍射仪和扫描电镜, 研究了热处理过程中的结构变化和表面形貌. 循环伏安和可见光透过率测试表明该氧化镍薄膜具有良好的电致变色性能和阳极着色效应.     

纳米Au-TiO2复合薄膜的溶胶-凝胶法制备、表征和性能

用溶胶-凝胶法制备了纳米Au-TiO₂复合薄膜.X射线衍射、X射线光电子能谱、原子力显微镜、紫外-可见光谱及摩擦磨损实验研究表明,复合薄膜均匀致密,Au以纳米晶粒形式均匀、不连续分散镶嵌于TiO₂基体中,纳米Au粒径为14～25nm;复合薄膜在可见光区有较强的吸收,吸收峰位置和强度与烧结温度和金的添加量有关;复合薄膜具有良好的抗磨减摩性能,在1N负荷下,摩尔分数为5%的Au-TiO₂薄膜的摩擦系数仅为0.09～0.10,耐磨寿命多于2000滑动周次.     

PREPARATION OF POLYSULFONAMIDE/TiO2 NANOCOMPOSITES BY SOL-GEL

Polysulfonamide (PSA) was synthesized at room temperature, the polymerization based on terephthaloyl chloride and 3,3 '-diaminodiphenylsulfone in the common solvent N,N -Dimethyl-acetamide (DMAc). Polysulfonamide/titanium oxide nanocomposites were prepared by sol-gel method. Tetrabutyl titanate(TBT) was added into the polysulfonamide solution, at the same time ,some water was mixed to make the TBT hydrolyze. In the process, hydrochloric acid was used to catalyze the reaction. The polysulfonamide chemistry structure was characterized by FT-IR spectrum. Atomic force microscopy (AFM) was employed to observe the microstructure of the composite film. The thermal property was investigated by TGA.The results show that we have succeeded to synthesize the polysulfonamide, TiO2particles were well distributed in the composite film and average size was about 20 nm on average, the heat-resistance of nanocomposite was batter than the pure polysulfonamide.     

电沉积Cu2xIn2-2xSe2薄膜的光电化学研究

用电沉积法制得Cu_2xIn_2-2xSe₂(铜铟硒)(0[1]并用EDAX对其组成进行分析。对薄膜电极的光电化学性能、光谱响应、能隙与x的依赖关系进行了研究。借助于现场微区扫描光电流谱观察了热处理、薄膜厚度、光极化对薄膜电极的光电性能影响。研究了Pb(NO₃)₂有效的浸渍对薄膜光电性能的影响。     

Vanadium Doped Sol-Gel TiO2 Coatings

A study of the experimental conditions required to obtain vanadium doped sol-gel TiO2 coatings is presented. Tetraethyl orthotitanate was employed as the TiO2 source and VCl3, VOSO4 · H2O and VOSO4 dissolved H2SO4 where employed as vanadium sources.Dip coating has been used to produce coatings on silicon wafers, spectral carbon electrodes and titanium electrodes. Both supported and unsupported films have been studied by UV-Vis spectra, IR spectroscopy and X-ray diffraction (XRD). The measurements have been made on samples as prepared and treated thermally at temperatures between 100°C and 300°C. The thermal treatment temperatures have been established from DTA/TGA measurements.The vanadium doped sol-gel TiO2 coatings have been tested as sensors for redox potential measurements in electrochemical processes. The influence of both the thickness of films and the nature of substrate has been investigated.     

溶胶-凝胶法制备丙烯酸树脂/TiO2有机-无机杂化材料及其结构表征

通过预水解的二氧化钛(TiO2 )溶胶与丙烯酸树脂共混或原位聚合的方法制备了均匀透明的丙烯酸树脂 TiO2 有机 无机杂化材料.考察了TiO2 溶胶制备方法、聚合物中—COOH官能团含量和杂化材料制备方法对杂化材料结构的影响.索氏抽提实验表明聚合物中的羧酸官能团和无机TiO2 相间发生了交联反应,且随着—COOH官能团含量的增加,交联程度增大.小角X射线散射(SAXS)结果发现,杂化材料中TiO2 为疏松的三维网状结构,且在纳米尺度范围内,但这种三维网状结构随着TiO2 溶胶制备中水或酸的用量增加,其致密度增加,尺寸增大.同原位聚合法相比,共混法可制备出更均匀的杂化体系,且TiO2 为单分散.     

利用二氧化钛簿膜光催化降解废水(英文)

主要研究了在ＴｉＯ２薄膜上光催化降解有机磷废水。结果表明,镀膜基片不同、光催化时间不同、ＴｉＯ２晶型不同均对降解速率有影响。感兴趣的是可以利用太阳紫外光降解有机磷废水。     

预处理对TiO2表面超亲水性的影响

在高湿度环境下,应用紫外光辐射对溶胶 凝胶TiO₂ 薄膜预处理,经过预处理的薄膜烧结后具有快速光致高度亲水特性和良好的光催化活性.超亲水的薄膜能够吸附大量的酸性品红,在光照下薄膜将吸附的酸性品红逐渐降解掉.     

纳米TiO2/Si薄膜的制备与光催化性能的研究

1972年, Fujishima等发现受辐射的TiO₂上可以持续发生水的氧化还原反应产生氢, 从此, 半导体光催化受到了重视并得到进一步广泛的研究^[1]。     

PREPARATION OF POLYSULFONAMIDE/TiO_2 NANOCOMPOSITES BY SOL-GEL

1. INTRODUCTIONPolysulfonamide resin can be used to prepare heat-resistant fibers. The first investigation was started by the Chinese scientists in the 1970’s [1], then it is widely used in industry field. Its aerospace and fire protection application ha…     

低压化学气相沉积法制备TiO2膜的研究

以四异丙醇钛为原料,采用低压化学气相沉积法研究ＴｉＯ２薄膜的沉积条件。采用紫外光谱、Ｘ射线衍射、扫描电镜等测试手段对ＴｉＯ２膜的光学性质及结构形貌进行了表征。实验表明：ＴｉＯ２膜在可见光和近红外范围内的折光率为３．１５,比用常压法制备的ＴｉＯ２膜的折光率高出３６．５％。因而,低压化学气相沉积法是制备高折射率的ＴｉＯ２膜更有效的一种方法。     

溶胶-凝胶法合成聚(甲基丙烯酸乙酯-甲基丙烯酸环氧丙酯)/SiO_2杂化聚合物材料

通过溶胶 凝胶过程合成了一系列存在相间偶联键的杂化聚合物材料 .IR分析证实了在无机组份与有机组份间存在碳氮键 ,其特征吸收峰在 1 2 5 0cm-1.DSC的测试结果则表明无机组份含量的增加提高了材料的Tg 值 ,从而提高了杂化材料的使用温度 .利用小角X ray散射 (SAXS)和电镜 (TEM)分析了不同无机组份、不同酸度下体系的形态结构 ,结果表明当无机组份与有机组份的摩尔比为 1∶1且体系的酸度适当时相容性最好 .