NO在氧化铝负载的Pd催化剂上吸附的TPD-MS研究

消除汽车尾气中的氮氧化物(NOx)对保护大气环境有着重要意义.为了除去NOx,已经进行了许多卓有成效的研究,例如NOx在分子筛上的直接分解和催化还原,在贵金属三效催化剂上的还原等.     

还原剂对La0.7Sr0.3Co0.8Fe0.2O3钙钛矿催化剂NOx储存性能的影响

采用溶胶-凝胶法制备了La0.7Sr0.3Co0.8Fe0.2O3钙钛矿催化剂,考察了还原剂种类(CO,C3H6,H2)对催化剂在氮氧化物储存还原(NSR)循环前后的氮氧化物储存量(NSC)和NO-to-NO2转化率的影响.O2程序升温脱附(O2-TPD)实验结果表明,CO还原后的钙钛矿催化剂上形成了较多的氧空位,而氧空位则是一种有效的NOx储存活性中心.活性测试和傅里叶红外变换(FTIR)光谱表征结果显示:在NSR循环中,以CO为还原剂时催化剂显示了最佳的氮氧化物(NOx)储存效果.进一步的研究结果显示,当采用CO作为还原剂时,经过三次NSR循环后,催化剂中出现了Sr3Fe2O7新物相,而该物相可能具有比La0.7Sr0.3Co0.8Fe0.2O3钙钛矿更佳的NOx储存性能.综上所述,CO作为还原剂时可能使钙钛矿催化剂产生更多的氧空位以及更易于储存NOx的Sr3Fe2O7物相,这些原因使其NOx储存性能得到了大幅度改善.     

添加稀土氧化物助剂的CeO2-ZrO2固溶体的储氧性及热稳定性研究

大多数工业催化剂都是在稳定的操作条件下进行的,然而汽车尾气净化催化剂却被暴露在大气中,使用条件经常变化,尤其是空燃比(A/F)的变化,直接影响了对氧敏感的三效催化剂的氧化和还原性能[1].CeO2则是一种具有储氧/释氧能力的催化材料,它作为助剂加入三效催化剂中,可在贫况下储存氧(以Ce4+存在)利于NOx的还原,在富况下释放氧(以Ce3+存在),利于HC、CO的氧化,从而提高了催化剂的活性.然而,CeO2 的储氧性通常局限在表面上,当温度超过400℃以上时,其比表面积降低从而引起储氧性能急剧下降,直接影响催化剂的性能和寿命.     

H2O、CO2组分对NOx存储-还原性能的影响

NOx存储-还原技术是控制汽车稀燃NOx排放的重要手段之一,在汽车尾气中H2O、CO2组分含量均相对较高,有必要弄清这些组分对NOx存储-还原特性的影响。论文以MnOx改性Pt/Ba/Al2O3催化剂为研究对象,评价在不同气氛下的NOx存储能力和催化还原性能。结果表明：CO2、H2O组分均抑制催化剂的NOx存储性能,H2O的抑制作用主要表现在低温区,CO2抑制NOx存储的现象在高温区更为显著。CO2对NOx存储速率的抑制作用较H2O更为明显,且其NOx存储速率随着温度的升高表现的差异性更为明显。对于NOx催化还原过程,CO2、H2O或CO2 H2O添加均导致N2选择性降低,其N2选择性按CO2 > H2O > CO2 H2O的顺序降低。     

金属-ZSM-5/堇青石整体式催化剂上稀燃汽车尾气的净化

 在原位合成的ZSM-5/堇青石整体式样品基础上制备了几种金属(Cu, In或Ag)改性的ZSM-5/堇青石催化剂,并将其应用于稀燃发动机尾气的净化. 结果表明, Cu-ZSM-5/堇青石催化性能最好,尾气中的三种主要污染物NOx, CO和HC可以同时得到净化. 用微量(0.02%)贵金属(Pd, Rh或Ir)对Cu-ZSM-5/堇青石进一步改性,所得催化剂对CO的净化能力大大增强,保持高NOx转化率的温度窗口也大大加宽,因而该催化剂在稀燃汽车尾气净化方面具有潜在的应用前景. 微量贵金属对Cu-ZSM-5/堇青石催化剂的改性作用也在文中进行了讨论.     

稀燃NO_x储存-还原催化剂

NOx储存-还原(NSR)技术是最有前景的稀燃氮氧化物消除技术,自从日本丰田公司1996年首次提出NOx储存-还原这一概念后,一直受到研究者的广泛关注。本文综述了近十余年来NSR催化剂(PBA型、水滑石型、钙钛矿型)的研究进展,重点概述了目前比较公认的NOx储存-还原的反应路径,以及NSR催化剂的失活机制,包括H2O和CO2的负面影响,热失活和硫中毒问题,最后展望了NOx储存还原技术未来的发展趋势。     

贫燃条件 In-Ag/TiO2-γ-Al2O3催化 CO选择性还原NO

汽车尾气中主要污染成分 CO和 NOx可导致酸雨、光化学烟雾和臭氧空洞效应,对生物、环境及生态系统造成重大危害。污染源中 CO是性能优良的还原剂,如能不添加还原剂实现 CO催化还原 NOx,将成为最具经济技术优势的 NOx脱除技术。在富氧、低温条件下,利用 CO选择性催化还原 NOx为 N2,是目前选择性催化还原研究中的热点和难点。催化 CO还原 NOx常用的贵金属 Ir, Rh, Pt和Pd矿藏稀少,价格昂贵,有氧条件下活性急降,而分子筛催化剂和一些金属氧化物催化剂普遍存在反应温度高,尤其对 N2选择性差等问题。为解决上述问题,需寻找新的适合我国矿产资源的催化体系。研究发现,稀散金属基催化剂对氮氧化物的净化具有一定效果,因而可将我国的稀散金属资源优势转化为技术优势和经济优势。因此,本文以 TiO2-γ-Al2O3(TA)为载体, In/Ag为活性组分,采用等体积浸渍法制备了 InAg/TA以及 In/TA, Ag/TA和InAg/Al (γ-Al2O3为载体)催化剂,考察了贫燃条件下 CO选择性还原NO的催化活性。研究表明,双金属催化剂InAg/Al和 InAg/TA的活性比单金属催化剂In/TA和 Ag/TA高, In/TA催化剂中引入 Ag物种能降低起燃温度;另外,相比于InAg/Al催化剂, InAg/TA催化剂具有较高的催化活性,550?600°C时 N2产率超过60%,说明载体中引入TiO2可以提高催化剂活性。为了深入研究 InAg/TA催化剂中 Ag物种和TiO2对 In物种的作用,通过比表面测定、X射线衍射(XRD)、透射电子显微镜(TEM)、X射线光电子能谱、紫外-可见光吸收光谱、氢气程序升温还原、傅立叶变换红外线光谱等方法分析了催化剂结构和表面形态。结果表明, Ag物种可以提高 In物种的分散性, In和 Ag物种在 TA载体表面可以很好地分散,从而有利于提高催化活性。 In和 Ag物种在 TA载体表面以氧化态形式存在,并且 Ag物种可以提高 In物种表面含量,表面 In和 Ag物种含量越高,吸附活性位越多,催化活性越高;同时, TiO2也可以促进 NO吸附,从而提高 InAg/TA催化剂活性。 InAg/TA催化剂在450°C连续反应72 h进行稳定性测试,测试前后分别在50?600°C进行活性测试,并用 XRD和 TEM对反应后的催化剂进行表征测试。结果表明, InAg/TA催化剂具有较好的稳定性,连续反应前后催化剂活性基本保持不变,推测可能由于在有 CO和O2存在的体系中, Ag物种利用自身 Ag+与 Ag0之间的氧化还原反应抑制了活性组分 In2O3的还原和聚集,稳定了 In物种乃至催化剂活性。 InAg/TA催化剂用于贫燃条件下CO还原NO具有较好的催化效果,主要归因于催化剂活性组分分散性好,稳定性高,对NO吸附能力强。 Ag物种可以稳定In物种并提高其分散性, TiO2可以改善In物种和Ag物种的分散性并促进NO吸附。     

富氧条件下Ag/Al2O3和Cu/Al2O3组合催化剂催化C3H6选择性还原Nox的性能

 在全自动催化剂活性评价装置上,考察了富氧条件下Ag/Al2O3和Cu/Al2O3两种催化剂上催化丙烯还原NOx的活性. 在实验温度范围(200～650 ℃)内,Ag/Al2O3具有 优异的催化丙烯选择性还原NOx的活性,但同时有大量副产物CO形成. Cu/Al2O3选择性催化丙烯还原NOx的活性不高,却能有效促进CO的氧化. 在无水条件,Ag/Al2O3-Cu/Al2O3组合体系具有与Ag/Al2O3相似的脱除NOx活性,同时使CO在300 ℃以后几乎完全转化. 在10%水蒸气存在的情况下,Ag/Al2O3-Cu/Al2O3组合催化剂脱除NOx的活性下降,但水蒸气对CO转化率的影响不大.     

Ce对Al2O3负载钙钛矿催化剂结构及性能的影响

制备了LaMn0.7Cu0.3和La0.3Ce0.7Mn0.7Cu0.3钙钛矿型汽车尾气净化催化剂,研究了Ce对LaMn基催化剂及分散层材料γ-Al2O3结构与性能的影响.结果发现,添加6%的氧气可将分散层材料γ-Al2O3向α-Al2O3相转变温度从800 ℃提高到1150 ℃,同时可使γ-Al2O3保持最大的比表面积.在LaMn/Cu催化活性材料中加入Ce,导致催化剂对HC, CO的氧化性能有一定程度的降低,但可明显改善催化剂对NOx的还原性能,其还原效率可达80%以上.在10%氧气的富氧条件下,在LaMn/Au催化材料中添加Ce,可使LaMn/Au活性层材料对NOx的还原效率达到40%以上. X射线衍射分析和扫描电子显微观察的结果表明,添加Ce在一定程度上抑制了LaMn基催化活性材料钙钛矿结构的形成和析出,降低了LaMn材料的钙钛矿晶粒尺寸,使表面活性成分分布更加均匀.     

汽车尾气与人体健康危害

汽车尾气排放的主要污染物为一氧化碳（CO）、碳氢化合物（HC）、氮氧化物（NOx）、铅（Pb）等。     

Liquid phase hydrogenolysis of dibenzyl ether over metals of the VIIIth group

It has been shown that depending on the catalyst and the solvent used, during the conversion of dibenzyl ether to toluene hydrogenolysis of C-O ether bonds, dehydrogenation and hydrogenolysis of benzyl alcohol formed, hydrogenation and decarbonylation of benzaldehyde, and the recombination of benzyl radicals and the benzylation of toluene can take place. The activity of catalysts in hydrogenolysis reactions of dibenzyl ether and benzyl alcohol to produce toluene decreases as follows: Pd/C>Pd>Raney Ni>Rh, whereas the selectivity drops down in the order: Raney Ni>Pd>Pd/C>Rh. The reaction rates depend on the solvent and diminish in the order: ethanol>2-propanol>benzene.Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 7, pp. 1257–1261, July, 1993.     

Thermal study of Cu(II), Ni(II) and Pd(II) chelates of resacetophenoneoxime

Summary Thermal analysis of resacetophenoneoxime and its chelates of Cu(II), Ni(II) and Pd(II) is carried out. A comparison is made between the thermal stability and the solution stability of chelates and found that they oppose each other. The thermal stability for the chelates studied is PdNi>Cu and the solution stability on the other hand is Pd>Cu>Ni. The results obtained were compared with the data available in the literature for structurally similar oximes. The advantages of the reagent for gravimetric and thermogravimetric analysis of metal ions were discussed.

---

Thermochemische Untersuchung der Cu(II)-, Ni(II)- und Pd(II)-Chelate von Resacetophenonoxim

Zusammenfassung Die thermische Stabilität der Chelate und ihre Stabilität in Lösung wurden verglichen und festgestellt, daß diese sich nicht entsprechen. Die erste nimmt ab in der Reihenfolge PdNi>Cu, die zweite in die Reihenfolge Pd>Cu>Ni. Die erhaltenen Ergebnisse wurden denen aus der Literatur für strukturell ähnliche Oxime gegenübergestellt. Die Vorteile des Reagenses für gravimetrische und thermogravimetrische Bestimmungen werden diskutiert.

     

Interaction of SO2 with single crystal metal surfaces

Studying the interaction of SO₂ with metal surfaces under UHV conditions, a question of central interest is whether the molecule dissociates (leaving back the catalyst poison sulphur on the surface) or not. A spontaneous or a thermally activated dissociation of SO₂ occurs on Fe, Rh, W, Ni, Pd and Pt. On Cu and Ag a strong chemisorption, but only a partial dissociation induced by defects or coadsorbed alkalis, and on Au no chemisorption at all were observed.

In this paper a comparison of our results obtained for the chemisorption and multilayer adsorption of SO₂ on Cu(111), Ag(111), Ag(100) and Ag(110) in the temperature range between 80 K and 900 K is given. By combining highly resolved TPD-measurements, isothermal and temperature-programmed ΔΦ-experiments after different stages of exposure and molecular beam backscattering measurements (MBBS) —assisted by LEED, AES and isotope mixing experiments — a destinction between ordinary desorption and desorption after a reorientation process during the heating procedure could be made. Whereas on clean Ag surfaces adsorption and desorption of SO₂ are observed only below 300 K, on Cs-precovered Ag desorption of SO₂ takes place even above 600 K.

Finally, results concerning the different stages of SO₂ multilayer adsorption (bi-, tri-, multilayers) are presented showing a characteristic dependence of the layer growth on the adsorption temperature, the impinging SO₂ flux density and on the surface structure.     

CO adsorption on pure and binary-alloy gold clusters: a quantum chemical study

We performed density-functional theory analysis of nondissociative CO adsorption on 22 binary Au-alloy (Au(n)M(m)) clusters: n=0-3, m=0-3, and m+n=2 (dimers) or 3 (trimers), M=Cu/Ag/Pd/Pt. We report basis-set superposition error corrections to adsorption energies and include both internal energy of adsorption (DeltaU(ads)) and Gibbs free energy of adsorption (DeltaG(ads)) at standard conditions (298.15 K and 1 atm). We found onefold (atop) CO binding on all the clusters except Pd2 (twofold/bridged), Pt2 (twofold/bridged), and Pd3 (threefold). In agreement with the experimental results, we found that CO adsorption is thermodynamically favorable on pure Au/Cu clusters but not on pure Ag clusters and also observed the following adsorption affinity trend: Pd>Pt>Au>Cu>Ag. For alloy dimers we found the following patterns: Au2>M Au>M2 (M=Ag/Cu) and M2>M Au>Au2 (M=Pd/Pt). Alloying Ag/Cu dimers with (more reactive) Au enhanced adsorption and the opposite effect was observed for PdPt dimers. The Ag-Au, Cu-Au, and Pd-Au trimers followed the trends observed on dimers: Au3>M Au2>M2Au>M3 (M=Ag/Cu) and Pd3>Pd2Au>PdAu2>Au3. Interestingly, Pt-Au trimers reacted differently and alloying with Au systematically increased the adsorption affinity: PtAu2>Pt2Au>Pt3>Au3. A strikingly different behavior of Pt is also manifested by the triplet spin state and onefold (atop) binding in Pt3-CO which is in contradiction with the singlet spin state and threefold binding in Pd3-CO. We found a linear correlation between CO binding energy (BE) and elongation of the CO bond. For Ag-Au and Cu-Au clusters, the increase in CO BE (and elongation of the C-O bond which is probably due to the back donation) is accompanied by the decrease in the cluster-CO distance suggesting that the donation (from 5sigma highest occupied molecular orbital in CO to cluster lowest unoccupied molecular orbital) mechanism also contributes to the BE. For Pd-Au clusters, the cluster-CO distance (and CO bond length) increases with increase in the BE, suggesting that the donation mechanism may not be important for those clusters. No clear trend was observed for Pt-Au clusters.     

The relationship between formate adsorption energy and electronic properties: A first principles density functional theory study

First principles density functional theory calculations have been performed for the chemisorption of formate adsorption on some metal surfaces. For the most stable adsorption site of short-bridge, the calculated formate adsorption energy follows the order of Au(110) < Ag(110) < Cu(110) < Pd(110) < Pt(110) < Ni(110) < Rh(110) < Fe(100) < Mo(100), and a clear linear correlation exists between the adsorption energy and the corresponding heat of formation of metal oxides. Moreover, it has been found that the fo...     

Catalytic effects of peroxidase-like metalloporphyrins on the fluorescence reaction of homovanillic acid with hydrogen peroxide

Summary The catalytic effects of peroxidase-like metalloporphyrins (Me-P) on the fluorescence reaction of homovanillic acid with hydrogen peroxide have been studied. These metalloporphyrins are the complexes of Mn with tetrakis(carboxyphenyl)porphyrin (TPPC) and trikis(sulfophenyl)porphyrin(TPPS₃), Fe, Co, Ni, Cu, Zn, Ag and Sn with tetrakis(sulfophenyl)porphyrin(TPPS₄), and Rh, Pt and Pd with tetrakis(N-methylpyridiniumyl)porphyrin-(TMPyP) and hemin. The complexes of Mn, Fe, Co, Rh and Pt with porphyrins catalyzed the formation of the fluorescence product, while the complexes of Ni, Cu, Zn, Ag, Sn and Pd did not. Traces of hydrogen peroxide and glucose can be determined using the metalloporphyrins. The characteristics of peroxidase-like metalloporphyrins have been compared with those of horseradish peroxidase (HRP).     

Alkyne Insertion into the M?P and M?H Bonds (M=Pd,Ni, Pt,and Rh): A Theoretical Mechanistic Study of the C?P and C?H Bond‐Formation Steps

In hydrogen‐metal‐phosphorus (H M P) transition metal complexes (proposed as intermediates of H P bond addition to alkynes in the catalytic hydrophosphorylation, hydrophosphinylation, and hydrophospination reactions), alkyne insertion into the metal‐hydrogen bond was found much more facile compared to alkyne insertion into the metal‐phosphorus bond. The conclusion was verified for different metals (Pd, Ni, Pt, and Rh), ligands, and phosphorus groups at various theory levels (B3LYP, B3PW91, BLYP, MP2, and ONIOM). The relative reactivity of the metal complexes in the reaction with alkynes was estimated and decreased in the order of Ni>Pd>Rh>Pt. A trend in relative reactivity was established for various types of phosphorus groups: PR₂>P(O)R₂>P(O)(OR)₂, which showed a decrease in rate upon increasing the number of the oxygen atoms attached to the phosphorus center.     

Expanding the scope of chemical vapor generation for noble and transition metals.

A modified Bergener parallel path nebulizer was used for the generation of volatile metal species of Pt, Co, Ag, Cu, Rh, Pd, Au, Ni, Ir, Ti and Mn through reaction with tetrahydroborate (III). Several physicochemical factors were identified which impact on their yield which, at present, is estimated to range from 0.02-2% absolute.     

Extractive concentration of platinum-group elements and their determination by atomic-absorption spectrophotometry

The extraction of Pt, Pd, Ir, Rh, Ru, Ag, Au, Co, Cu, Ni and Fe with n-octylaniline has been investigated. Noble metals are extracted 10(3)-10(4) times better than Cu, Ni, Co and Fe. A method of determination of Pt, Pd, Ir, Rh and Ru is proposed. They are first separated from Cu, Ni, Co and Fe by means of extraction (and then determined, in either the aqueous or organic phase, by atomic-absorption spectrophotometry. The atomic absorption of platinum metals (with the exception of Pd) is affected by other elements of the platinum group and by non-noble metals. La(NO(3))(3) and Nd(NO(3))(3) lower the limit of detection for Pt, Rh, Ir and Ru and inhibit the effect of Co, Cu, Ni, Fe, Bi, Zn, Na, etc. on their determination. Lanthanum and neodymium chlorides and sulphates produce a similar effect but only on the determination of Pt and Rh. The coefficient of variation of the determination, in both phases, is within 2-6.8%.