A new methodology for precise cadmium isotope analyses of seawater

Previous studies have revealed considerable Cd isotope fractionations in seawater, which can be used to study the marine cycling of this micronutrient element. The low Cd concentrations that are commonly encountered in nutrient-depleted surface seawater, however, pose a particular challenge for precise Cd stable isotope analyses. In this study, we have developed a new procedure for Cd isotope analyses of seawater, which is suitable for samples as large as 20 L and Cd concentrations as low as 1 pmol/L. The procedure involves the use of a ¹¹¹Cd–¹¹³Cd double spike, co-precipitation of Cd from seawater using Al(OH)₃, and subsequent Cd purification by column chromatography. To save time, seawater samples with higher Cd contents can be processed without co-precipitation. The Cd isotope analyses are carried out by multiple collector inductively coupled plasma mass spectrometry (MC-ICP-MS). The performance of this technique was verified by analyzing multiple aliquots of a large seawater sample that was collected from the English Channel, the SAFe D1 seawater reference material, and several samples from the GEOTRACES Atlantic intercalibration exercise. The overall Cd yield of the procedure is consistently better than 85% and the methodology can routinely provide ε ^114/110Cd data with a precision of about ±0.5 ε (2sd, standard deviation) when at least 20–30 ng of natural Cd is available for analysis. However, even seawater samples with Cd contents of only 1–3 ng can be analyzed with a reproducibility of about ±3 to ±5 ε. A number of experiments were furthermore conducted to verify that the isotopic results are accurate to within the quoted uncertainty.     

Development of pre-concentration procedure for the determination of Hg isotope ratios in seawater samples

Hg concentrations in seawater are usually too low to allow direct (without pre-concentration and removal of salt matrix) measurement of its isotope ratios with multicollector-inductively coupled plasma mass spectrometry (MC-ICP-MS). Therefore, a new method for the pre-concentration of Hg from large volumes of seawater was developed. The final method allows for relatively fast (about 2.5 L h⁻¹) and quantitative pre-concentration of Hg from seawater samples with an average Hg recovery of 98 ± 6%. Using this newly developed method we determined Hg isotope ratios in seawater. Reference seawater samples were compared to samples potentially impacted by anthropogenic activity. The results show negative mass dependent fractionation relative to the NIST 3133 Hg standard with δ²⁰²Hg values in the range from −0.50‰ to −1.50‰. In addition, positive mass independent fractionation of ²⁰⁰Hg was observed for samples from reference sites, while impacted sites did not show significant Δ²⁰⁰Hg values. Although the influence of the impacted sediments is limited to the seawater and particulate matter in very close proximity to the sediment, this observation may raise the possibility of using Δ²⁰⁰Hg to distinguish between samples from impacted and reference sites.     

Analysis of trace levels of domoic acid in seawater and plankton by liquid chromatography without derivatization,using UV or mass spectrometry detection

Quantitation of trace levels of domoic acid (DA) in seawater samples usually requires labour-intensive protocols involving chemical derivatization with 9-fluorenylmethylchloroformate and liquid chromatography with fluorescence detection (FMOC–LC–FLD). Procedures based on LC–MS have been published, but time-consuming and costly solid-phase extraction pre-concentration steps are required to achieve suitable detection limits. This paper describes an alternative, simple and inexpensive LC method with ultraviolet detection (LC–UVD) for the routine analysis of trace levels of DA in seawater without the use of sample pre-concentration or derivatization steps. Qualitative confirmation of DA identity in dubious samples can be achieved by mass spectrometry (LC–MS) using the same chromatographic conditions. Addition of an ion-pairing/acidifying agent (0.15% trifluoroacetic acid) to sample extracts and the use of a gradient elution permitted the direct analysis of large sample volumes (100 μl), resulting in both high selectivity and sensitivity (limit of detection = 42 pg ml⁻¹ by LC–UVD and 15 pg ml⁻¹ by LC–MS). Same-day precision varied between 0.4 and 5%, depending on the detection method and DA concentration. Mean recoveries of spiked DA in seawater by LC–UVD were 98.8% at 0.1–10 ng ml⁻¹ and 99.8% at 50–1000 ng ml⁻¹. LC–UVD exhibited strong correlation with FMOC–LC–FLD during inter-laboratory analysis of Pseudo-nitzschia multiseries cultures containing 60–2000 ng DA ml⁻¹ (r² > 0.99), but more variable results were obtained by LC–MS (r² = 0.85). This new technique was used to confirm the presence of trace DA levels in low-toxicity Pseudo-nitzschia spp. isolates (0.2–1.6 ng ml⁻¹) and in whole-water field samples (0.3–5.8 ng ml⁻¹), even in the absence of detectable Pseudo-nitzschia spp. cells in the water column.     

Uranium determination in seawater by total reflection X-ray fluorescence spectrometry

A study regarding uranium determination in seawater by total reflection X-ray fluorescence (TXRF) spectrometry is reported. Uranium, present in seawater in concentration of about 3.3 ng/mL, was selectively extracted in diethyl ether and determined by TXRF after its preconcentration by evaporation and subsequent dissolution in a small volume of 1.5% suprapure HNO₃. Yttrium was used as an internal standard. Before using diethyl ether for selective extraction of uranium from seawater, its extraction behavior for different elements was studied using a multielement standard solution having elemental concentrations in 5 ng/mL levels. It was observed that the extraction efficiency of diethyl ether for uranium was about 100% whereas for other elements it was negligible. The detection limit of TXRF method for uranium in seawater samples after pre-concentration step approaches to 67 pg/mL. The concentrations of uranium in seawater samples determined by TXRF are in good agreement with the values reported in the literature. The method shows a precision within 5% (1σ). The study reveals that TXRF can be used as a fast analytical technique for the determination of uranium in seawater.     

Fast concentration of dissolved forms of cesium radioisotopes from large seawater samples

The method developed for cesium concentration from large freshwater samples was tested and adapted for analysis of cesium radionuclides in seawater. Concentration of dissolved forms of cesium in large seawater samples (about 100 L) was performed using composite absorbers AMP-PAN and KNiFC-PAN with ammonium molybdophosphate and potassium–nickel hexacyanoferrate(II) as active components, respectively, and polyacrylonitrile as a binding polymer. A specially designed chromatography column with bed volume (BV) 25 mL allowed fast flow rates of seawater (up to 1,200 BV h^?1). The recovery yields were determined by ICP-MS analysis of stable cesium added to seawater sample. Both absorbers proved usability for cesium concentration from large seawater samples. KNiFC-PAN material was slightly more effective in cesium concentration from acidified seawater (recovery yield around 93 % for 700 BV h^?1). This material showed similar efficiency in cesium concentration also from natural seawater. The activity concentrations of ¹³⁷Cs determined in seawater from the central Pacific Ocean were 1.5 ± 0.1 and 1.4 ± 0.1 Bq m^?3 for an offshore (January 2012) and a coastal (February 2012) locality, respectively, ¹³⁴Cs activities were below detection limit (<0.2 Bq m^?3).     

Application of micro‐solid‐phase extraction for the on‐site extraction of heterocyclic aromatic amines in seawater

An efficient on‐site extraction technique to determine carcinogenic heterocyclic aromatic amines in seawater has been reported. A micro‐solid‐phase extraction device placed inside a portable battery‐operated pump was used for the on‐site extraction of seawater samples. Before on‐site applications, parameters that influence the extraction efficiency (extraction time, type of sorbent materials, suitable desorption solvent, desorption time, and sample volume) were investigated and optimized in the laboratory. The developed method was then used for the on‐site sampling of heterocyclic aromatic amines determination in seawater samples close to distillation plant. Once the on‐site extraction completed, the small extraction device with the analytes was brought back to the laboratory for analysis using high‐performance liquid chromatography with fluorescence detection. Based on the optimized conditions, the calibration curves were linear over the concentration range of 0.05–20 μg/L with correlation coefficients up to 0.996. The limits of detection were 0.004–0.026 μg/L, and the reproducibility values were between 1.3 and 7.5%. To evaluate the extraction efficiency, a comparison was made with conventional solid‐phase extraction and it was applied to various fortified real seawater samples. The average relative recoveries obtained from the spiked seawater samples varied in the range 79.9–95.2%.     

A new method for precise determination of iron,zinc and cadmium stable isotope ratios in seawater by double-spike mass spectrometry

The study of Fe, Zn and Cd stable isotopes (δ⁵⁶Fe, δ⁶⁶Zn and δ¹¹⁴Cd) in seawater is a new field, which promises to elucidate the marine cycling of these bioactive trace metals. However, the analytical challenges posed by the low concentration of these metals in seawater has meant that previous studies have typically required large sample volumes, highly limiting data collection in the oceans. Here, we present the first simultaneous method for the determination of these three isotope systems in seawater, using Nobias PA-1 chelating resin to extract metals from seawater, purification by anion exchange chromatography, and analysis by double spike MC-ICPMS. This method is designed for use on only a single litre of seawater and has blanks of 0.3, 0.06 and <0.03 ng for Fe, Zn and Cd respectively, representing a 1–20 fold reduction in sample size and a 4–130 decrease in blank compared to previously reported methods. The procedure yields data with high precision for all three elements (typically 0.02–0.2‰; 1σ internal precision), allowing us to distinguish natural variability in the oceans, which spans 1–3‰ for all three isotope systems. Simultaneous extraction and purification of three metals makes this method ideal for high-resolution, large-scale endeavours such as the GEOTRACES program.     

In-field determination of nanomolar nitrite in seawater using a sequential injection technique combined with solid phase enrichment and colorimetric detection

A novel sequential injection method for the determination of nitrite at nanomolar level in seawater samples has been developed. The pink azo compound was formed based on the Griess reaction and quantitatively adsorbed onto a Sep-Pak C18 cartridge. The enriched azo compound was rinsed with water and ethanol (28%, v/v) in turn, and then eluted with an eluent containing 26.6% (v/v) ethanol and 0.108 mol L⁻¹ H₂SO₄. Finally the azo compound was measured using a spectrophotometer at 543 nm. Under the optimized conditions, the linear calibration ranges were 0.71–42.9 nmol L⁻¹ for a 150-mL sample and 35.7–429 nmol L⁻¹ for a 15-mL sample. The relative standard deviation of 8 measurements was 1.44% for 14.3 nmol L⁻¹ nitrite. For the 150 mL sample, the detection limit was estimated to be 0.1 nmol L⁻¹. The throughput of the method was about 4 samples per hour. The proposed method has been successfully applied to the in-field determination of nanomolar concentrations of nitrite in seawater.     

Semi-micro ion chromatography of iodide in seawater

Large sample volume injections including both on-column analyte focusing and on-column matrix elimination techniques were examined for semi-micro ion chromatography of trace iodide (I⁻) in seawater. A semi-microcolumn (35×1 mm I.D.) packed with styrene–divinylbenzene copolymer with high anion-exchange capacity and a mobile phase of 0.03 M NaClO₄+0.5 M NaCl+5 mM sodium phosphate buffer, pH 6.0, was used. Iodide in seawater was effectively concentrated on the column by both electrostatic and hydrophobic interactions and was eluted without peak broadening. ClO₄⁻ (NaClO₄) in the mobile phase was effective for the elution of iodide and Cl⁻ (NaCl) for both the concentration of iodide (I⁻) with hydrophobicity and the removal of interference by the major anions. An excess of major anions in seawater did not disturb the detection of iodide at UV 226 nm. The relative standard deviations for successive injections of 5 and 1 μg/l I⁻ (2 ml of 35‰ artificial seawater) were 1.5 and 5.8% (n=5, each), respectively. The slope of calibration curve (by peak area) using the semi-microcolumn was ∼2.8-times higher than that for a conventional column with the same resin (150×4.6 mm I.D.) The present method had a detection limit of 0.2 μg/l I⁻ for 2 ml of 35‰ artificial seawater and was successfully applied to seawater samples.     

Precise determination of lithium isotopes in seawater using MC-ICP-MS

Li (lithium) isotope analysis using MC-ICP-MS is a very powerful tracer measurement method. This is widely used for identification of Li isotopes in many fields of study. This useful method, however, has an effect on the natural Li isotope background. This is impacted by the instrument matrix. In this study, we show that the MC-ICP-MS condition is characterized by both a low baseline background and a high-sensitivity distance at Ar plasma condition. In addition, the Li isotope ratio was measured by the use of experimental conditions that were superior to both the general plasma condition and those used in other studies. The samples were subjected to both acid leaching and a cation exchange resin (Bio-Rad AG 50 W-X8 200–400 mesh) modified for seawater samples. The isotope variations were corrected using the bracket method, the measured Li isotope ratio of sample, and the mean ratios of the L-SVEC standard (NIST L-SVEC Li₂CO₃) measured before and after the sample run. The isotope variation was presented as the deviation (per mil) of the measured ratio from that of the recommended value.     

A permeation liquid membrane system for determination of nickel in seawater

The use of a permeation liquid membrane system for the preconcentration and separation of nickel in natural and sea waters and subsequent determination by atomic absorption spectroscopy is presented. 2-Hydroxybenzaldehyde N-ethylthiosemi-carbazone (2-HBET) in toluene is used as the active component of the liquid membrane. A study strategy based on a simplex design has been followed. Several chemical and physical parameters were optimized. Maximum permeation coefficient was obtained at a feed solution pH of 9.4, 0.3 mol l⁻¹ of HNO₃ in the stripping solution and 1.66 mmol l⁻¹ of 2-HBTE in toluene as carrier. The precision of the method was 4.7% at 95% significance level and a detection limit of 0.012 μg l⁻¹ of nickel was achieved. The preconcentration procedure showed a linear response within the studied concentration range from 3 to 500 μg l⁻¹ of Ni in the feed solution. The method was validated with different spiked synthetic seawater and certified reference water samples: TMDA-62 and LGC 6016, without matrix interferences and showing good concordance with the certified values, being the relative errors −5.9% and −2.2%, respectively. Under optimal conditions, the average preconcentration yield for real seawater samples was 98 ± 5%, with a nickel preconcentration factor of 20.83 and metal concentrations ranging between 2.8 and 5.4 μg l⁻¹.     

Highly selective separation and detection of cyromazine from seawater using graphene oxide based molecularly imprinted solid‐phase extraction

A novel molecularly imprinted polymer based on graphene oxide was prepared as a solid‐phase extraction adsorbent for the selective adsorption and extraction of cyromazine from seawater samples. The obtained graphene oxide molecularly imprinted polymer and non‐imprinted polymer were nanoparticles and characterized by scanning electron microscopy. The imprinted polymer showed higher adsorption capacity and better selectivity than non‐imprinted polymer, and the maximum adsorption capacity was 14.5 mg/g. The optimal washing and elution solvents for molecularly imprinted solid phase extraction procedure were 2 mL of acetonitrile/water (80:20, v/v) and methanol/acetic acid (70:30, v/v), respectively. The recoveries of cyromazine in the spiked seawater samples were in the range of 90.3–104.1%, and the relative standard deviation was <5% (n = 3) under the optimal procedure and detection conditions. The limit of detection of the proposed method was 0.7 μg/L, and the limit of quantitation was 2.3 μg/L. Moreover, the imprinted polymer could keep high adsorption capacity for cyromazine after being reused six times at least. Finally, the synthesized graphene oxide molecularly imprinted polymer was successfully used as a satisfied sorbent for high selectivity separation and detection of cyromazine from seawater coupled with high‐performance liquid chromatography.     

Determination of uranium in seawater by flow-injection preconcentration on dodecylamidoxime-impregnated resin and spectrophotometric detection

A flow injection method has been developed for the determination of uranium in seawater combining the on-line preconcentration with spectrophotometric detection. An aliquot (10 mL) of the seawater sample adjusted to pH 5.5 was injected into the analytical system and uranium was adsorbed on the column packed with styrene-divinylbenzene copolymer resin (Bio-Beads SM-2) modified with dodecylamidoxime which showed high selectivity to uranium. Uranium was then eluted with 0.01 M hydrochloric acid and detected spectrophotometrically after the reaction with Chlorophosphonazo III. Interference from calcium and strontium was masked with cyclohexanediaminetetraacetic acid added to the chromogenic reagent solution. The sample throughput, the detection limit (3σ), and the preconcentration factor were 23 per hour, 0.13 μg/L, and 20, respectively, when the sample injection volume was kept at 10 mL. The precision at the 2 μg/L level was less than 4% (RSD). The proposed method was applied to the determination of uranium in the seawater samples collected off the Boso peninsula, Japan and the uranium concentration was found to be ca. 3 μg/L, which is close to the literature data. The yield of the recovery test ranged from 95% to 99%.     

Simple,quantitative method for low molecular weight dissolved organic matter extracted from natural waters based upon high performance counter-current chromatography

A simple, high-performance counter-current chromatography method with sequential UV absorbance (254 nm) and evaporative light scattering detection (ELSD) was developed for the quantification of pre-extracted low molecular weight dissolved organic matter (DOM) extracted from natural waters. The method requires solid-phase extraction (SPE) extraction of only small volumes of water samples, here using poly(styrenedivinylbenzene)-based extraction cartridges (Varian PPL). The extracted and concentrated DOM was quantified using reversed-phase high-performance counter-current chromatography (HPCCC), with a water/methanol (5:5) mobile phase and hexane/ethyl acetate (3:7) stationary phase. The critical chromatographic parameters were optimised, applying a revolution speed of 1900 rpm and a flow-rate of 1 mL min⁻¹. Under these conditions, 50 μL of extracted DOM solution could be injected and quantified using calibration against a reference natural dissolved material (Suwannee River), based upon UV absorbance at 254 nm and ELSD detection. Both detection methods provided excellent linearity (R² > 0.995) for DOM across the concentration ranges of interest, with limits of detection of 4 μg ml⁻¹ and 7 μg ml⁻¹ for ELSD and UV absorbance, respectively. The method was validated for peak area precision (<5%), and accuracy and recovery based upon spiking seawater samples prior to extraction, together with DOM solutions post-extraction (>95% recovery). The developed method was applied to the determination of the concentration of DOM in seawater, based upon initial sample volumes as small as 20 mL.     

Determination of Trimethylamine N-oxide and Betaine in Serum and Food by Targeted Metabonomics

Trimethylamine N-oxide (TMAO), as a gut-derived metabolite, has been found to be associated with enhanced risk for atherosclerosis and cardiovascular disease. We presented a method for targeted profiling of TMAO and betaine in serum and food samples based on a combination of one-step sample pretreatment and proton nuclear magnetic resonance spectroscopy. The key step included a processing of sample preparation using a selective solid-phase extraction column for retention of basic metabolites. Proton signals at δ 3.29 and δ 3.28 were employed to quantify TMAO and betaine, respectively. The developed method was examined with acceptable linear relationship, precision, stability, repeatability, and accuracy. It was successfully applied to detect serum levels of TMAO and betaine in TMAO-fed mice and high-fructose-fed rats and also used to determine the contents of TMAO and betaine in several kinds of food, such as fish, pork, milk, and egg yolk.     

Determination of trace zinc in seawater by coupling solid phase extraction and fluorescence detection in the Lab-On-Valve format

By virtue of their compactness, long-term stability, minimal reagent consumption and robustness, miniaturized sequential injection instruments are well suited for automation of assays onboard research ships. However, in order to reach the sensitivity and limit of detection required for open-ocean determinations of trace elements, it is necessary to preconcentrate the analyte prior its derivatization and subsequent detection by fluorescence. In this work, a novel method for the determination of dissolved zinc (Zn) at subnanomolar levels in seawater is described. The proposed method combines, for the first time, automated matrix removal, extraction of the target element, and fluorescence detection within a miniaturized flow manifold, based on the Lab-On-Valve (LOV) concept. The key feature of the microfluidic manipulation of the sample is flow programming, designed to pass sample through a mini-column where the target analyte and other complexable cations are retained, while the seawater matrix is washed out. Next, zinc is eluted and merged with a Zn selective fluorescent probe (FluoZin-3) at the confluence point of the LOV central channel using two high-precision stepper motor driven pumps that are operated in concert. Finally, the thus formed Zn complex is transported to the LOV flow cell for selective fluorescence measurement. This work describes the characterization and optimization of the method including Solid Phase Extraction using the Toyopearl AF-Chelate-650M resin, and detailed assay protocol controlled by a commercially available software and instrument. The proposed method features a LOD of 0.02 nM, high precision (<3% at 0.1 and 2 nM Zn levels), an assay cycle of 13 min and a reagent consumption of 150 μL FluoZin-3 per sample, which makes the method highly suitable for oceanographic shipboard analysis. The accuracy of the method has been validated through the analysis of seawater reference standards and comparison with ICP-MS determinations on seawater samples collected in the upper 1300 m of the subtropical south Indian Ocean. This work confirms that integration of sample pretreatment with optical detection in the LOV format offers a widely applicable approach to trace analysis of seawater.     

First results on Fe solid-phase extraction from coastal seawater using anatase TiO2 nano-particles

This paper describes the application of TiO₂ nano-particles (anatase form) for the solid-phase extraction of iron from coastal seawater samples. We investigated the adsorption processes by infra-red spectroscopy. We compared in batch and on-(mini)column extraction approaches (0.1 and 0.05 g TiO₂ per sample, respectively), combined to external calibration and detection by inductively coupled plasma mass spectrometry at medium mass resolution. Globally, this titania phase was slightly more efficient with seawater than with ultra-pure water, although between pH 2 and pH 7, the Fe retention efficiency progressed more in ultra-pure water than in seawater (6.9 versus 4.8 times improvement). Different reaction schemes are proposed between Fe(III) species and the two main categories of titania sites at pH 2 (adsorption of [FeL _x ]^{(3 − x)+} via possibly the mediation of chlorides) and at pH 7 (adsorption of [Fe(OH)₂]⁺ and precipitation of [Fe(OH)₃]⁰). Under optimised conditions, the inlet system was pre-cleaned by pumping 6% HCl for ∼2 h, and the column was conditioned by aspirating ultra-pure water (1.7 g min⁻¹) and 0.05% ammonia (0.6 g min⁻¹) for 1 min. Then 3 g seawater sample was loaded at the same flow rate while being mixed on-line with 0.05% ammonia at 0.6 g min⁻¹ to adjust the pH to 7. The iron retained on the oxide powder was then eluted with 3 g 6% HCl (<0.002% residual salinity in the separated samples). The overall procedural blank was 220 ± 46 (2 s, n = 16) ng Fe kg⁻¹ (the titania was renewed in the column every 20 samples, with 2-min rinsing in between samples with 6% HCl at 1.5 g min⁻¹). The recovery estimated from the Canadian certified reference material CASS-2 was 69.5 ± 7.6% (2 s, n = 4). Typically, the relative combined uncertainty (k = 2) estimated for the measurement of ∼1 μg Fe kg⁻¹ (0.45 μm filtered and acidified to pH 1.5) of seawater was ∼12%. We applied our method to a similar sample, from the coastal region of the North Sea. The agreement well within stated uncertainties of our result with the value obtained independently by isotope dilution mass spectrometry further validated our method.     

Validation and application of an LC-MS/MS method for the simultaneous quantification of 13 pharmaceuticals in seawater

Knowledge of the presence of micropollutants such as pharmaceuticals, in coastal areas, is very limited; therefore, the main objective of this study was to optimize and validate a new analytical method for the quantitative analysis of 13 multiclass pharmaceuticals in seawater. Target compounds included antibiotics, non-steroidal anti-inflammatory drugs, β-blockers, lipid regulators and one psychiatric drug. A combination of solid-phase extraction and liquid chromatography coupled with multiple mass spectrometry enabled their detection at the low nanogram per litre level. The limits of quantification varied between 1 and 50 ng L^-1, for most components the linearities were more than 0.99 and the recoveries obtained in seawater (95–108%) were satisfactory. This method was applied to seawater and estuarine water samples collected in the Belgian coastal zone, to assess the prevalence of common pharmaceuticals in this marine environment. Seven pharmaceuticals, including compounds of which the presence in marine environments had not been reported earlier, were detected, with salicylic acid and carbamazepine being the most abundant, in concentrations up to 855 ng L^-1.     

Association of uranium with colloidal and suspended particulate matter in Arabian sea near the west coast of Maharashtra (India)

The purpose of the present study is the association of natural uranium in seawater with colloidal and suspended-particulate matter was determined. The separation of suspended particulate material (>0.45 µm) and colloidal fraction (as dissolved fractions) in seawater were done by suction and ultra filtration techniques. Seawater samples were collected at 1 km away from the shore and subjected to sequential fractionation in nine stages ranging from 2.7 µm to 1.1 nm. Suspended particulate matter were separated in three different size groups namely >2.7 µm, <2.7–>0.45 µm and <0.45–>0.22 µm by suction filtration using cellulose acetate and nitrate membranes filters. To concentrate the solution with colloidal particles <0.22 µm–1.1 nm (0.5 k Nominal Molecular Weight cut-off Limit {NMWL}), the solution obtained from filtration through <0.22 µm was passed through stirred ultra-filtration cell. The pH and conductivity at different stages of fractionation (dissolved) showed minor variations. The concentration of uranium was measured in suspended and dissolved fractions by using a pulsed nitrogen laser at 337.1 nm. In order to evaluate the role of mineral colloids in various stages of filtration, concentration of calcium, magnesium, potassium were measured by using ion chromatography and atomic absorption spectrometry. The clay mineral at seawater pH (approximately 8) behave as negative ions and provides binding site for the positively charge species of uranium. Among the dissolved fraction, the maximum concentrations of colloidal uranium was observed about 4 times higher than that compared to average concentration of 6.93±3.10 ppb in other fractions. In the case of suspended particulate matter, the concentration of uranium was below detection limits (<1 ppb). The maximum concentration of Ca, Mg and K in the dissolved fraction were in the <1.1 nm fraction, while for suspended particulate matter, the concentration of Ca, Mg and K decreased with the decrease in size and it is highest in the fraction of 0.22 –0.45 µm.This revised version was published online in November 2005 with corrections to the Cover Date.     

Ultrasensitive determination of cadmium in seawater by hollow fiber supported liquid membrane extraction coupled with graphite furnace atomic absorption spectrometry

A new procedure, based on hollow fiber supported liquid membrane preconcentration coupled with graphite furnace atomic absorption spectrometry (GFAAS) detection, was developed for the determination of trace Cd in seawater samples. With 1-octanol that contained a mixture of dithizone (carrier) and oleic acid immobilized in the pores of the polypropylene hollow fiber as a liquid membrane, Cd was selectively extracted from water samples into 0.05 M HNO₃ that filled the lumen of the hollow fiber as a stripping solution. The main extraction related parameters were optimized, and the effects of salinity and some coexisting interferants were also evaluated. Under the optimum extraction conditions, an enrichment factor of 387 was obtained for a 100-mL sample solution. In combination with graphite furnace atomic absorption spectrometry, a very low detection limit (0.8 ng L^− 1) and a relative standard deviation (2.5% at 50 ng L^− 1 level) were achieved. Five seawater samples were analyzed by the proposed method without dilution, with detected Cd concentration in the range of 56.4–264.8 ng L^− 1 and the relative spiked recoveries over 89%. For comparison, these samples were also analyzed by the Inductively Coupled Plasma Mass Spectrometry (ICP-MS) method after a 10-fold dilution for matrix effect elimination. Statistical analysis with a one-way ANOVA shows no significant differences (at 0.05 level) between the results obtained by the proposed and ICP-MS methods. Additionally, analysis of certified reference materials (GBW (E) 080040) shows good agreement with the certified value. These results indicate that this present method is very sensitive and reliable, and can effectively eliminate complex matrix interferences in seawater samples.