An intimately bonded titanate nanotube–polyaniline–gold nanoparticle ternary composite as a scaffold for electrochemical enzyme biosensors

In this work, titanate nanotubes (TNTs), polyaniline (PANI) and gold nanoparticles (GNPs) were assembled to form a ternary composite, which was then applied on an electrode as a scaffold of an electrochemical enzyme biosensor. The scaffold was constructed by oxidatively polymerising aniline to produce an emeraldine salt of PANI on TNTs, followed by gold nanoparticle deposition. A novel aspect of this scaffold lies in the use of the emeraldine salt of PANI as a molecular wire between TNTs and GNPs. Using horseradish peroxidase (HRP) as a model enzyme, voltammetric results demonstrated that direct electron transfer of HRP was achieved at both TNT-PANI and TNT-PANI-GNP-modified electrodes. More significantly, the catalytic reduction current of H₂O₂ by HRP was ∼75% enhanced at the TNT-PANI-GNP-modified electrode, compared to that at the TNT-PANI-modified electrode. The heterogeneous electron transfer rate constant of HRP was found to be ∼3 times larger at the TNT-PANI-GNP-modified electrode than that at the TNT-PANI-modified electrode. Based on chronoamperometric detection of H₂O₂, a linear range from 1 to 1200 μM, a sensitivity of 22.7 μA mM⁻¹ and a detection limit of 0.13 μM were obtained at the TNT-PANI-GNP-modified electrode. The performance of the biosensor can be ascribed to the superior synergistic properties of the ternary composite.     

Direct electrochemistry and electrocatalysis of hemoglobin on chitosan-room temperature ionic liquid-TiO(2)-graphene nanocomposite film modified electrode

TiO₂-graphene nanocomposite was prepared by hydrolysis of titanium isopropoxide in colloidal suspension of graphene oxide and in situ hydrothermal treatment. The direct electrochemistry and electrocatalysis of hemoglobin in room temperature ionic liquid 1-Butyl-3-methylimidazolium hexafluorophosphate, chitosan and TiO₂-graphene nanocomposite modified glassy carbon electrode were investigated. The biosensor was examined by using UV-vis spectroscopy, scanning electron microscopy and electrochemical methods. The results indicated that hemoglobin remained its bioactivity on the modified electrode, showing a couple of well-defined and quasi-reversible redox peaks, corresponding to hemoglobin Fe^III/Fe^II couple. The kinetic parameters for the electrode reaction, such as the formal potential (E^o'), the electron transfer rate constant (k_s), the apparent coverage (Γ), and Michaelis–Menten constant (K_m) were evaluated. The biosensor showed good electrochemical responses to the reduction of H₂O₂ in the ranges of 1–1170 μM. The detection limit was 0.3 μM (S/N = 3). The properties of this composite film, together with the bioelectrochemical catalytic activity, could make them useful in the development of bioelectronic devices, and investigation of electrochemistry of other heme proteins at functional interface.     

Growth of non-enzymatic cholesterol biosensor using TiO2 decorated graphene oxide with bare GCE and PPy-GCE

In this work, we report an electrochemical cholesterol biosensor based on cholesterol oxidase(ChOx) enzyme immobilized on TiO₂- nanoparticles – reduced graphene oxide(rGO) – polypyrrole (PPy) nanocomposite modified electrode.The electrochemical properties of GCE modified PPy (PPy-GCE) were studied using CV (Cyclic Voltammetry) and DPV (Differential Pulse Voltammetry). The developed sensor exhibited piecewise linearity from 0.1 μM to 1 μM and from 1 μM to 600 μM with the sensitivity of 61.665 and 0.1466 (2 mA mM × cm) respectively. The limit of detection of the sensor was found to be 32 nm.     

Direct electrochemistry of hemoglobin and its biosensing for hydrogen peroxide on TiO2–polystyrene nanofilms

Nanofilms of titanium dioxide (TiO₂) nanoparticles that mediate the assembly of polystyrene (PS) nanoparticles for immobilizing hemoglobin (Hb) on carbon ionic liquid electrode have been developed. Fourier transform infrared spectroscopy shows that Hb retains its native structure in TiO₂–PS nanofilms. Scanning electron microscopy reveals that the nanofilms possess uniform morphology and Hb is immobilized on the surface of the nanofilms. Electrochemical investigation of the biosensor indicates that the direct electrochemistry of hemoglobin is realized on the nanofilms, and there is a formal potential of ?0.320 V in deaerated buffer solutions; the biosensor shows good electrocatalytic activity toward the reduction of hydrogen peroxide with a linear range from 0.5 to 640 μM, a detection limit of 0.2 μM (S/N = 3) and a sensitivity of 103 μA mM^?1. Thus, the nanofilms will have potential application in the design of novel electrochemical biosensors.     

On-chip type cation-exchange chromatography with ferrocene-labeled anti-hemoglobin antibody and electrochemical detector for determination of hemoglobin A1c level

An on-chip type cation-exchange chromatography system with electrochemical detection of HbA_1c, which is one of the most important diabetes marker protein, was developed using ferrocene-conjugated anti-human hemoglobin (Hb) monoclonal antibody (FcAb). The FcAb was used as an electrochemical probe for the detection of each Hb. The system contains syringe pump, on-chip type cation-exchange column consisted of PDMS and cation-exchange resin beads, and a three-electrode flow-cell system. The separation conditions of HbA_1c in blood calibrator samples from other Hbs, e.g. HbA₀, HbA_1a or HbA_1b, were optimized using the on-chip type system. The electrochemical oxidation current from FcAb reacting with each Hb was measured at 350 mV (vs. Ag/AgCl). Hbs including HbA_1a and HbA_1b, HbA_1c and HbA₀ fractions were eluted in this order. A linear relationship between HbA_1c levels and electrochemical oxidation currents was obtained in the range from 4.0% to 12.6% HbA_1c. All procedure including antigen-antibody reaction was completed in 15 min. Furthermore, a good correlation was obtained between KO500 method (HPLC) and our proposed method. These results indicate that the on-chip type system with electrochemical detection can be applied to a novel POCT device for rapid and precise detection of HbA_1c.     

An enzymatic method for the rapid measurement of the hemoglobin A1c by a flow-injection system comprised of an electrochemical detector with a specific enzyme-reactor and a spectrophotometer

A flow-injection analytical (FIA) system, comprised of an electrochemical detector with a fructosyl-peptide oxidase (FPOX-CET) reactor and a flow-type spectrophotometer, was proposed for the simultaneous measurement of glycohemoglobin and total hemoglobin in blood cell. The blood cell samples were hemolyzed with a surfactant and then treated with protease. In the first stage of operation, total hemoglobin in digested sample was determined spectrophotometrically. In the second stage, fructosyl valyl histidine (FVH) released from glycohemoglobin by the selective proteolysis was determined specifically using the electrochemical detector with the FPOX-CET reactor. The FIA system could be automatically processed at an analytical speed of 40 samples per hour. The proposed assay method could determine selectively only the glycated N-terminal residue of β-chain in glycohemoglobin and total hemoglobin in blood cell. The enzymatic hemoglobin A_1c (HbA_1c) value calculated by the concentration ratio of the FVH to total hemoglobin, was closely correlated with the HbA_1c values certified by the Japan Diabetic Society (JDS) and the International Federation of Clinical Chemistry (IFCC).     

Direct Electrochemistry of Hemoglobin Immobilized on Colloidal Gold‐Hydroxyapatite Nanocomposite for Electrocatalytic Detection of Hydrogen Peroxide

A novel nanocomposite of colloidal gold (GNPs) and hydroxyapatite nanotubes (Hap) was prepared for immobilization of a redox protein, hemoglobin (Hb), on glassy carbon electrode. The immobilized Hb showed fast direct electron transfer and excellent electrocatalytic behavior toward reduction of hydrogen peroxide. A synergic effect between GNPs and Hap for accelerating the surface electron transfer of Hb was observed, which led to a pair of redox peaks with a formal potential of (?340±2) mV at pH 7.0, and a new biosensor for hydrogen peroxide with a linear range from 0.5 to 25 μM and a limit of detection of 0.2 μM at 3σ. Owing to the good biocompatibility of the nanocomposite, the biosensor exhibited good stability and acceptable reproducibility. The as‐prepared nanocomposite film provided a good matrix for protein immobilization and biosensor preparation.     

Direct electrochemistry and electroanalysis of hemoglobin adsorbed in self-assembled films of gold nanoshells

Gold nanoshells (GNSs), consisting of a silica core and a thin gold shell, were self-assembled on the surface of 3-aminopropyltrimethoxysilane (APTES) modified indium tin oxide (ITO) electrode. The resulting novel GNSs-coated ITO (GNSs/APTES/ITO) electrode could provide a biocompatible surface for the adsorption of hemoglobin (Hb). The UV-visible (UV-vis) spectra indicated that Hb adsorbed on the GNSs interface retained the native structure. Electrochemical impedance spectra and cyclic voltammetric techniques were employed to evaluate the electrochemical behaviors of Hb, the results demonstrated that GNSs could act as electron tunnels to facilitate electron transfer between Hb and the electrode. Based on the activity of Hb adsorbed on the GNSs/APTES/ITO electrode toward the reduction of hydrogen peroxide, a mediator-free H₂O₂ biosensor was constructed, which showed a broad linear range from 5 μM to 1 mM with a detection limit of 3.4 μM (S/N = 3). The apparent Michaelis-Menten constant was calculated to be 180 μM, suggesting a high affinity.     

A novel amperometric biosensor for the detection of nitrophenol

We report on a novel amperometric biosensor for detecting phenolic compounds based on the co-immobilization of horseradish-peroxidase (HRP) and methylene blue (MB) with chitosan on Au-modified TiO₂ nanotube arrays. The titania nanotube arrays were directly grown on a Ti substrate using anodic oxidation first; a gold thin film was then coated onto the TiO₂ nanotubes by an argon plasma technique. The morphology and composition of the fabricated Au-modified TiO₂ nanotube arrays were characterized by scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS). Cyclic voltammetry and amperometry were used to study the proposed electrochemical biosensor. The effect of pH, applied electrode potential and the concentration of H₂O₂ on the sensitivity of the biosensor have been systemically investigated. The performance of the proposed biosensor was tested using seven different phenolic compounds, showing very high sensitivity; in particular, the linearity of the biosensor for the detection of 3-nitrophenol was observed from 3 × 10⁻⁷ to 1.2 × 10⁻⁴ M with a detection limit of 9 × 10⁻⁸ M (based on the S/N = 3).     

Nafion covered core–shell structured Fe3O4@graphene nanospheres modified electrode for highly selective detection of dopamine

Nafion covered core–shell structured Fe₃O₄@graphene nanospheres (GNs) modified glassy carbon electrode (GCE) was successfully prepared and used for selective detection dopamine. Firstly, the characterizations of hydro-thermal synthesized Fe₃O₄@GNs were investigated by scanning electron microscopy (SEM), transmission electron microscopy (TEM) and Raman spectroscopy. Then Fe₃O₄@GNs/Nafion modified electrode exhibited excellent electrocatalytic activity toward the oxidations of dopamine (DA). The interference test showed that the coexisted ascorbic acid (AA) and uric acid (UA) had no electrochemical interference toward DA. Under the optimum conditions, the broad linear relationship was obtained in the experimental concentration from 0.020 μM to 130.0 μM with the detection limit (S/N = 3) of 0.007 μM. Furthermore, the core–shell structured Fe₃O₄@GNs/Nafion/GCE was applied to the determination of DA in real samples and satisfactory results were got, which could provide a promising platform to develop excellent biosensor for detecting DA.     

Prussian blue modified glassy carbon electrodes-study on operational stability and its application as a sucrose biosensor

Stabilisation of electrochemically deposited Prussian blue (PB) films on glassy carbon (GC) electrodes has been investigated and an enhancement in the stability of the PB films is reported if the electrodes are treated with tetrabutylammonium toluene-4-sulfonate (TTS) in the electrochemical activation step following the electrodeposition. A multi-enzyme PB based biosensor for sucrose detection was made in order to demonstrate that PB films can be coupled with an oxidase system. A tri-enzyme system, comprising glucose oxidase, mutarotase and invertase, was crosslinked with glutaraldehyde and bovine albumin serum on the PB modified glassy carbon electrode. The deposited PB operated as an electrocatalyst for electrochemical reduction of hydrogen peroxide, the final product of the enzyme reaction sequence. The electrochemical response was studied using flow injection analysis for the determination of sucrose, glucose and H₂O₂. The optimal concentrations of the immobilisation mixture was standardised as 8 U of glucose oxidase, 8 U of mutarotase, 16 U of invertase, 0.5% glutaraldehyde (0.025 μl) and 0.5% BSA (0.025 mg) in a final volume of 5 μl applied at the electrode surface (0.066 cm²). The biosensor exhibited a linear response for sucrose (4-800 μM), glucose (2-800 μM) and H₂O₂ (1-800 μM) and the detection limit was 4.5, 1.5 and 0.5 μM for sucrose, glucose and H₂O₂, respectively. The sample throughput was ca. 60 samples h⁻¹. An increase in the operational and storage stability of the sucrose biosensor was also noted when the PB modified electrodes were conditioned in phosphate buffer containing 0.05 M TTS during the preparation of the PB films.     

Detection of nicotine based on molecularly imprinted TiO2-modified electrodes

Amperometric detection of nicotine (NIC) was carried out on a titanium dioxide (TiO₂)/poly(3,4-ethylenedioxythiophene) (PEDOT)-modified electrode by a molecular imprinting technique. In order to improve the conductivity of the substrate, PEDOT was coated onto the sintered electrode by in situ electrochemical polymerization of the monomer. The sensing potential of the NIC-imprinted TiO₂ electrode (ITO/TiO₂[NIC]/PEDOT) in a phosphate-buffered saline (PBS) solution (pH 7.4) containing 0.1 M KCl was determined to be 0.88 V (vs. Ag/AgCl/saturated KCl). The linear detection range for NIC oxidation on the so-called ITO/TiO₂[NIC]/PEDOT electrode was 0-5 mM, with a sensitivity and limit of detection of 31.35 μA mM⁻¹ cm⁻² and 4.9 μM, respectively. When comparing with the performance of the non-imprinted one, the sensitivity ratio was about 1.24. The sensitivity enhancement was attributed to the increase in the electroactive area of the imprinted electrode. The at-rest stability of the ITO/TiO₂[NIC]/PEDOT electrode was tested over a period of 3 days. The current response remained about 85% of its initial value at the end of 2 days. The ITO/TiO₂[NIC]/PEDOT electrode showed reasonably good selectivity in distinguishing NIC from its major interferent, (−)-cotinine (COT). Moreover, scanning electrochemical microscopy (SECM) was employed to elucidate the surface morphology of the imprinted and non-imprinted electrodes using Fe(CN)₆³⁻/Fe(CN)₆⁴⁻ as a redox probe on a platinum tip. The imprinted electrode was further characterized by scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FTIR).     

Multilayer Assembly of Hemoglobin and Colloidal Gold Nanoparticles on Multiwall Carbon Nanotubes/Chitosan Composite for Detecting Hydrogen Peroxide

Chitosan (CS) was chosen for dispersing multi‐wall carbon nanotubes (MWNTs) to form a stable CS‐MWNTs composite, which was first coated on the surface of a glassy carbon electrode to provide a containing amino groups interface for assembling colloidal gold nanoparticles (GNPs), followed by the adsorption of hemoglobin (Hb). Repeating the assembly step of GNPs and Hb resulted in {Hb/GNPs}_n multilayers. The assembly of GNPs onto CS‐MWNTs composites was confirmed by transmission electron microscopy. The consecutive growth of {Hb/GNPs}_n multilayers was confirmed by cyclic voltammetry and UV‐vis absorption spectroscopy. The resulting system brings a new platform for electrochemical devices by using the synergistic action of the electrocatalytic activity of GNPs and MWNTs. The resulting biosensor displays an excellent electrocatalytic activity and rapid response for hydrogen peroxide. The linear range for the determination of H₂O₂ was from 5.0×10^?7 to 2.0×10^?3 M with a detection limit of 2.1×10^?7 M at 3σ and a Michaelis–Menten constant K_M^app value of 0.19 mM.     

Exploiting multi-function Metal-Organic Framework nanocomposite Ag@Zn-TSA as highly efficient immobilization matrixes for sensitive electrochemical biosensing

A novel multi-function Metal-Organic Framework composite Ag@Zn-TSA (zinc thiosalicylate, Zn(C₇H₄O₂S), Zn-TSA) was synthesized as highly efficient immobilization matrixes of myoglobin (Mb)/glucose oxidase (GOx) for electrochemical biosensing. The electrochemical biosensors based on Ag@Zn-TSA composite and ionic liquid (IL) modified carbon paste electrode (CPE) were fabricated successfully. Furthermore, the properties of the sensors were discussed by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and amperometric current-time curve, respectively. The results showed the proposed biosensors had wide linear response to hydrogen peroxide (H₂O₂) in the range of 0.3–20,000 μM, to nitrite (NO₂⁻) for 1.3 μM–1660 μM and 2262 μM–1,33,000 μM, to glucose for 2.0–1022 μM, with a low detection limit of 0.08 μM for H₂O₂, 0.5 μM for NO₂⁻, 0.8 μM for glucose. The values of the apparent heterogeneous electron transfer rate constant (k_s) for Mb and GOx were estimated as 2.05 s⁻¹ and 2.45 s⁻¹, respectively. Thus, Ag@Zn-TSA was a kind of ideal material as highly efficient immobilization matrixes for sensitive electrochemical biosensing. In addition, this work indicated that MOF nanocomposite had a great potential for constructing wide range of sensing interface.     

Au-TiO2/Chit modified sensor for electrochemical detection of trace organophosphates insecticides

In this paper, Au–TiO₂/Chit modified electrode was prepared with Au–TiO₂ nanocomposite (Au–TiO₂) and Chitosan (Chit) as a conjunct. The Au–TiO₂ nanocomposite and the films were characterized by electrochemical and spectroscopy methods. A set of experimental conditions was also optimized for the film's fabrication. The electrochemical and electrocatalytic behaviors of Au–TiO₂/Chit modified electrode to trace organophosphates (OPs) insecticides such as parathion were discussed in this work. By differential pulse voltammetry (DPV) measurement, the current responses of Au–TiO₂/Chit modified electrode were linear with parathion concentration ranging from 1.0 ng/ml to 7.0 × 10³ ng/ml with the detection limit of 0.5 ng/ml. In order to evaluate the performance of the detection system, we also examined the real samples successfully in this work. It exhibited a sensitive, rapid and easy-to-use method for the fast determination of trace OPs insecticides.     

Direct electron transfer of cytochrome c and its biosensor based on gold nanoparticles/room temperature ionic liquid/carbon nanotubes composite film

A robust and effective composite film based on gold nanoparticles (GNPs)/room temperature ionic liquid (RTIL)/multi-wall carbon nanotubes (MWNTs) modified glassy carbon (GC) electrode was prepared by a layer-by-layer self-assembly technique. Cytochrome c (Cyt c) was successfully immobilized on the RTIL-nanohybrid film modified GC electrode by electrostatic adsorption. Direct electrochemistry and electrocatalysis of Cyt c were investigated. The results suggested that Cyt c could be tightly adsorbed on the modified electrode. A pair of well-defined quasi-reversible redox peaks of Cyt c was obtained in 0.10 M, pH 7.0 phosphate buffer solution (PBS). RTIL-nanohybrid film showed an obvious promotion for the direct electron transfer between Cyt c and the underlying electrode. The immobilized Cyt c exhibited an excellent electrocatalytic activity towards the reduction of H₂O₂. The catalysis currents increased linearly to the H₂O₂ concentration in a wide range of 5.0 × 10⁻⁵– 1.15 × 10⁻³ M. Based on the multilayer film, the third-generation biosensor could be constructed for the determination of H₂O₂.     

Nano composite system based on coumarin derivative–titanium dioxide nanoparticles and ionic liquid: Determination of levodopa and carbidopa in human serum and pharmaceutical formulations

The combination of coumarin derivative (7-(1,3-dithiolan-2-yl)-9,10-dihydroxy-6H-benzofuro[3,2-c]chromen-6-on), (DC)–titanium dioxide nanoparticles (TiO₂) and ionic liquid (IL) yields nanostructured electrochemical sensor, formed a novel kind of structurally uniform and electrocatalytic activity material. This new ionic liquid–TiO₂ nanoparticles modified carbon paste electrode (IL–CTP) due to its enhanced conductivity presented very large current response from electroactive substrates. The modified electrode was characterized by different methods including a scanning electron microscope (SEM), electrochemical impedance spectroscopy (EIS) and voltammetry. A pair of well-defined quasi reversible redox peaks of coumarin derivative was obtained at the modified carbon paste electrode (DC/IL–CTP) by direct electron transfer between the coumarin derivative and the CP electrode. Dramatically enhanced electrocatalytic activity was exemplified at the DC/IL–CTP electrode, as an electrochemical sensor to study the electro oxidation of levodopa (LD) and carbidopa (CD). Based on differential pulse voltammetry (DPV), the oxidation of LD and CD exhibited the dynamic range between 0.10– 900.0 μM and 20.0–900.0 μM respectively, and the detection limit (3σ) for LD and CD were 41 nM and 0.38 μM, respectively. DPV was used for simultaneous determination of LD and CD at the DC/IL–CTP electrode, and quantitation of LD and CD in some real samples (such as tablets of Parkin-C Fort and Madopar, Sinemet, water, urine, and human blood serum) by the standard addition method.     

A sensitive mediator-free tyrosinase biosensor based on an inorganic-organic hybrid titania sol-gel matrix

A novel inorganic-organic hybrid titania sol-gel nanocomposite film was prepared to fabricate a sensitive tyrosinase biosensor for the amperometric detection of trace phenolic compounds without additional electron mediators. Acetylacetone worked as a complexing ligand to chelate with Ti atom in the synthesis process, and the pH of the titania solution could be adjusted to the value which was optimum for retaining tyrosinase activity and such a membrane was stably attached on to the surface of a glassy carbon electrode (GCE). This titania matrix could supply a good environment for enzyme loading, which resulted in a high sensitivity of 15.78 μA μM⁻¹ cm⁻² for monitoring phenols with a detection limit of 1×10⁻⁸ M at a signal-to-noise ratio of 3. The TiO₂ sol-gel derived biosensor exhibited a fast response less than 10 s and a good stability for more than 2 months.     

A novel nonenzymatic biosensor for evaluation of oxidative stress based on nanocomposites of graphene blended with CuI

A high-sensitive nonenzymatic hydrogen peroxide (H₂O₂) biosensor based on cuprous iodide and graphene (CuI/Gr) composites has been explored for the detection of H₂O₂ released by living cells and monitoring the oxidative stress of cells under excellular stimulation. The biosensor properties were evaluated by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), amperometric i-t curve, and the redox-competition mode of scanning electrochemical microscopy (SECM). Our observations demonstrate that the CuI/Gr nanocomposites modified glassy carbon electrode (GCE) exhibits excellent catalytic activity for H₂O₂ with relatively low detection limit and a wide linear range from 0.5 μM to 3 mM. Moreover, the redox-competition mode of SECM imaging study further illustrates the improved electrochemical catalytic capability for H₂O₂ reduction with CuI/Gr nanocomposites deposited on graphite electrode. Hence, the as-prepared nonenzymatic H₂O₂ biosensor could be used to detect H₂O₂ release from different kinds of living cells under stimulation while eliminating the interference of ascorbic acid.     

Immobilization of Ni–Pd/core–shell nanoparticles through thermal polymerization of acrylamide on glassy carbon electrode for highly stable and sensitive glutamate detection

The preparation of a persistently stable and sensitive biosensor is highly important for practical applications. To improve the stability and sensitivity of glutamate sensors, an electrode modified with glutamate dehydrogenase (GDH)/Ni–Pd/core–shell nanoparticles was developed using the thermal polymerization of acrylamide (AM) to immobilize the synthesized Ni–Pd/core–shell nanoparticles onto a glassy carbon electrode (GCE). The modified electrode was characterized by scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy, cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS). Electrochemical data showed that the prepared biosensor had remarkably enhanced electrocatalytic activity toward glutamate. Moreover, superior reproducibility and excellent stability were observed (relative average deviation was 2.96% after continuous use of the same sensor for 60 times, and current responses remained at 94.85% of the initial value after 60 d). The sensor also demonstrated highly sensitive amperometric detection of glutamate with a low limit of detection (0.052 μM, S/N = 3), high sensitivity (4.768 μA μM⁻¹ cm⁻²), and a wide, useful linear range (0.1–500 μM). No interference from potential interfering species such as l-cysteine, ascorbic acid, and l-aspartate were noted. The determination of glutamate levels in actual samples achieved good recovery percentages.