Room temperature ionic liquid doped DNA network immobilized horseradish peroxidase biosensor for amperometric determination of hydrogen peroxide

A novel electrochemical H₂O₂ biosensor was constructed by embedding horseradish peroxide (HRP) in a 1-butyl-3-methylimidazolium tetrafluoroborate doped DNA network casting on a gold electrode. The HRP entrapped in the composite system displayed good electrocatalytic response to the reduction of H₂O₂. The composite system could provide both a biocompatible microenvironment for enzymes to keep their good bioactivity and an effective pathway of electron transfer between the redox center of enzymes, H₂O₂ and the electrode surface. Voltammetric and time-based amperometric techniques were applied to characterize the properties of the biosensor. The effects of pH and potential on the amperometric response to H₂O₂ were studied. The biosensor can achieve 95% of the steady-state current within 2 s response to H₂O₂. The detection limit of the biosensor was 3.5 μM, and linear range was from 0.01 to 7.4 mM. Moreover, the biosensor exhibited good sensitivity and stability. The film can also be readily used as an immobilization matrix to entrap other enzymes to prepare other similar biosensors. Figure Horseradish peroxidase (HRP) embedded in a 1-butyl-3-methylimidazolium tetrafluoroborate (BMIM·BF ₄ ) doped DNA network can be used to fabricate a HRP sensor for the determination of H₂O₂     

超顺磁性氧化石墨烯复合材料固定辣根过氧化物酶催化去除氯酚

采用超声辅助共沉淀法成功地将磁性Fe3O4纳米颗粒沉积在氧化石墨烯表面,利用透射电镜、磁滞回归曲线和X射线光电子能谱对材料进行了表征。将该材料作为载体固定辣根过氧化物酶,考察了固定化酶催化2-氯酚、4-氯酚和2,4-二氯酚降解反应,研究了溶液pH值、反应温度、反应时间、H2O2和氯酚浓度以及固定化酶用量对酚类物质去除率的影响。基于取代基数量和位置不同,去除率排序为2-氯酚<4-氯酚<2,4-二氯酚。另外,采用GC-MS研究了降解过程中的氧化产物。固定化酶的生化性质研究表明,固定化酶比游离酶具有更好的储存稳定性、pH稳定性和热稳定性。经过4次循环利用,固定化酶仍保留66%的活性,说明磁性纳米材料可以分离回收并重复利用,在污水处理领域具有应用前景。     

以OT为底物固体电极伏安法测定辣根过氧化物酶及其标记物的研究

以玻碳电极为工作电极研究了邻联甲苯胺(OT)为底物微分脉冲伏安法测定辣根过氧化物酶(HRP)及其标记物的方法。HRP能够催化H2O2氧化OT,其反应产物在玻碳电极上-0.58V(vs.Ag/AgCl)左右被还原产生一个灵敏的还原峰,还原峰电流随着酶浓度的增大而增大,借助此还原电流可以测定HRP,并进而可用于以HRP为标记物的酶免疫分析。对酶催化反应条件和酶催化反应产物的测定条件进行了详细的研究,在最佳实验条件下测定游离HRP的线性范围是2.0×10-9～4.0×10-8g/mL,检出限为1.6×10-9g/mL;测定游离的酶标记物(IgG HRP),稀释范围为1∶2000～1∶400000,最大稀释比为1∶400000。     

Hydrogen peroxide sensor based on horseradish peroxidase immobilized on a silver nanoparticles/cysteamine/gold electrode

A third-generation hydrogen peroxide biosensor was prepared by immobilizing horseradish peroxidase (HRP) on a gold electrode modified with silver nanoparticles. A freshly-cleaned gold electrode was first immersed in a cysteamine–ethanol solution, and then silver nanoparticles were immobilized on the cysteamine monolayer, and finally HRP was adsorbed onto the surfaces of the silver nanoparticles. This self-assemble process was examined via atomic force microscopy (AFM). The immobilized horseradish peroxidase exhibited an excellent electrocatalytic response toward the reduction of hydrogen peroxide. The linear range of the biosensor was 3.3 M to 9.4 mM, and the detection limit was estimated to be 0.78 M. Moreover, the biosensor exhibited a fast response, high sensitivity, good reproducibility, and long-term stability.     

Electrochemical characteristics of a platinum electrode modified with a matrix of polyvinyl butyral and colloidal Ag containing immobilized horseradish peroxidase

A new hydrogen peroxide biosensor was constructed, which consisted of a platinum electrode modified by a matrix of polyvinyl butyral (PVB) and nanometer-sized Ag colloid containing immobilized horseradish peroxidase (HRP), and using Co(bpy)₃³⁺ as mediator in the hydrogen peroxide solution. The electrochemical characteristics of the biosensor were studied by cyclic voltammetry and chronoamperometry. The modified process was characterized by electrochemical impedance spectroscopy and cyclic voltammetry. The HRP immobilized on colloidal Ag was stable and retained its biological activity. The sensor displays excellent electrocatalytic response to the reduction of H₂O₂. Analytical parameters such as pH and temperature were also studied. Linear calibration for H₂O₂ was obtained in the range of 1×10^–5 to 1×10^–2 M under optimized conditions. The sensor was highly sensitive to H₂O₂, with a detection limit of 2×10^–6 M, and the sensor achieved 95% of steady-state current within 10 s. The sensor exhibited high sensitivity, selectivity and stability.     

Direct electrochemistry and electrocatalysis of horseradish peroxidase immobilized on L-glutathione self-assembled monolayers

A novel hydrogen peroxide biosensor has been fabricated based on covalently linked horseradish peroxidase （HRP） onto L- glutathione self-assembled monolayers （SAMs）. The SAMs-based electrode was characterized by electrochemical methods, and direct electrochemistry of HRP can be achieved with formal potential of-0.242 V （vs. saturated Ag/AgCl） in pH 7 phosphate buffer solution （PBS）, the redox peak current is linear to scan rate and rate constant can be calculated to be 0.042 s^-1. The HRP-SAMs- based biosensors show its better electrocatalysis to hydrogen peroxide in the concentration range of 1 × 10^-6 mol/L to 1.2 × 10^-3 mol/L with a detection limit of 4 × 10^-7 mol/L. The apparent Michealis-Menten constant is 3.12 mmol/L. The biosensor can effectively eliminate the interferences of dopamine, ascorbic acid, uric acid, catechol and p-acetaminophen.     

Direct electrochemistry and electrocatalysis of horseradish peroxidase immobilized in hybrid organic-inorganic film of chitosan/sol-gel/carbon nanotubes

A hybrid organic-inorganic nanocomposite film of chitosan/sol-gel/multi-walled carbon nanotubes was constructed for the immobilization of horseradish peroxidase (HRP). This film was characterized by scanning electron microscopy. Direct electron transfer (DET) and bioelectrocatalysis of HRP incorporated into the composite film were investigated. The results indicate that the film can provide a favorable microenvironment for HRP to perform DET on the surface of glassy carbon electrodes with a pair of quasi-reversible redox waves and to retain its bioelectrocatalytic activity toward H₂O₂.     

A biosensing platform based on horseradish peroxidase immobilized onto chitosan-wrapped single-walled carbon nanotubes

One-step, diameter-selective dispersion of single-walled carbon nanotubes (SWCNTs) has been accomplished through noncovalent complexation of the nanotubes with a water-soluble, biocompatible polymer chitosan at room temperature. Such chitosan-wrapped individual SWCNTs can be used for the immobilization of horseradish peroxidase (HRP) and be used to construct an electrode for direct bioelectrochemical sensing without an electron mediator. The direct electron transfer between HRP and the electrode surface was observed with a formal potential of approximately −0.35 V (vs. saturated calomel electrode) in phosphate buffer solution and the calculated heterogeneous electron transfer rate constant is approximately 23.5 s⁻¹. Experimental results indicate that the immobilized HRP retains its catalytic activity for the reduction of nitric oxide. Such an HRP–SWCNT–chitosan-based biosensor exhibited a rapid response time of less than 6 s and a good linear detection range for nitrite concentration, from 25 to 300 μM with a detection limit of 3 μM. The apparent Michaelis–Menten constant (K _m) and the maximum electrode sensitivity (i_max/K _m) are found to be 7.0 mM and 0.16 μA mM⁻¹, respectively. Both the unique electrical properties of SWCNTs and biocompatibility of chitosan enable the construction of an excellent biosensing platform for improved electrocatalysis of HRP, allowing, specifically, the detection of trace levels of nitric oxide.     

An amperometric hydrogen peroxide biosensor based on immobilization of horseradish peroxidase on an electrode modified with magnetic dextran microspheres

A new kind of magnetic dextran microsphere (MDMS) with uniform shape and narrow diameter distribution has been prepared from magnetic iron nanoparticles and dextran. Horseradish peroxidase (HRP) was successfully immobilized on the surface of an MDMS-modified glassy-carbon electrode (GCE), and the immobilized HRP displayed excellent electrocatalytic activity in the reduction of H₂O₂ in the presence of the mediator hydroquinone (HQ). The effects of experimental variables such as the concentration of HQ, solution pH, and the working potential were investigated for optimum analytical performance. This biosensor had a fast response to H₂O₂ of less than 10 s and an excellent linear relationship was obtained in the concentration range 0.20 μmol L⁻¹–0.68 mmol L⁻¹, with a detection limit of 0.078 μmol L⁻¹ (S/N = 3) under the optimum conditions. The response showed Michaelis–Menten behavior at larger H₂O₂ concentrations, and the apparent Michaelis–Menten constant was estimated to be 1.38 mmol L⁻¹. Moreover, the selectivity, stability, and reproducibility of the biosensor were evaluated, with satisfactory results. Figure Amperometric response of the biosensor to successive additions of H₂O₂ and the plot of amperometric response vs. H₂O₂ concentration     

Flowerlike hybrid horseradish peroxidase nanobiocatalyst for the polymerization of guaiacol

In this study, the catalytic activity and stability of flowerlike hybrid horseradish peroxidase (HRP) nanobiocatalyst (HRP-Cu ²⁺ ) obtained from Cu ²⁺ ions and HRP enzyme in the polymerization reaction of guaiacol were analyzed. We demonstrated that HRP-Cu ²⁺ and hydrogen peroxide (H ₂ O ₂ ) initiator showed significantly increased catalytic activity and stability on the polymerization of guaiacol compared to that of free HRP enzyme. Poly(guaiacol) was observed with quite high yields (88%) and molecular weights (38,000 g/mol) under pH 7.4 phosphate-buffered saline (PBS) conditions at 60 °C with 5 weight% of HRP-Cu ²⁺ loading. HRP-Cu ²⁺ also shows very high thermal stability and works even at 70 °C reaction temperature; free HRP enzyme denatures at that temperature. Furthermore, HRP-Cu ²⁺ provided considerable repeated use and showed some degree of catalytic activity, even after the fourth recycle, in the polymerization of guaiacol.     

Voltammetric determination of alkaline phosphatase and horseradish peroxidase activity using 3-indoxyl phosphate as substrate Application to enzyme immunoassay

The use of 3-indoxyl phosphate (3-IP) as an electrochemical substrate for ELISAs with voltammetric detection was investigated. Indirect measurements of alkaline phosphatase (AP) and horseradish peroxidase (HRP) activity in solution were carried out. Picomolar levels of both enzymes can be detected, which enables the design of electrochemical immunoassays using this substrate. The enzymatic turnover of the substrate gives indigo blue, insoluble in aqueous solutions. This product is easily converted into its soluble parent compound, indigo carmine (IC), by addition of fuming sulphuric acid to the reaction media. IC shows a reversible voltammetric peak at the formal potential of −0.15 V (versus Ag pseudo-reference electrode) when a screen-printed carbon electrode (SPCE) is used. The peak current of this process constitutes the analytical signal. Using this approach an ELISA assay to quantify pneumolysin (PLY, a toxin related to respiratory infections) was carried out using AP or HRP as enzymatic label. Calibration plots obtained are reported. 3-IP is demonstrated to be the first suitable substrate for the two most common enzyme labels used in immunoassays.     

Direct electrochemistry and electrocatalysis of horseradish peroxidase immobilized in sol–gel-derived tin oxide/gelatin composite films

Horseradish peroxidase (HRP) was immobilized into a new type of sol–gel-derived nano-sized tin oxide/gelatin composite film (SnO₂ composite film) using a sol–gel film/enzyme/sol–gel film “sandwich” configuration. Direct electrochemistry and electrocatalysis of HRP incorporated into the composite films were investigated. HRP/SnO₂ composite film exhibited a pair of stable and quasi-reversible cyclic voltammetric peaks for the HRP Fe(III)/HRP Fe(II) redox couple with a formal potential of about −0.25 V (vs. SCE) in a pH 6.0 phosphate buffer solution. The electron transfer between the enzyme and the underlying electrode was greatly enhanced in the microenvironment with nano-SnO₂ particles and nanoporous structures. Morphologies and microstructures of the composite films and HRP/composite films were characterized with TEM, AFM. Electrochemical impedance spectroscopy (EIS) was also used to feature the HRP incorporated into composite films. FTIR and UV–Vis spectroscopy demonstrated that HRP in the composite film could retain its native secondary structure. With the advantages of organic–inorganic hybrid materials, the HRP/SnO₂ composite film modified electrode displayed good stability and electrocatalytic activity to the reduction of H₂O₂, The apparent Michaelis-Menten constant was estimated to be 0.345 mM, indicating a high affinity of HRP entrapped into the composite film toward H₂O₂.     

Amperometric biosensor for hydrogen peroxide based on coimmobilized horseradish peroxidase and methylene green in ormosils matrix with multiwalled carbon nanotubes

A novel amperometric biosensor for the analytical determination of hydrogen peroxide was developed. The fabrication of the biosensor was based on the coimmobilization of horseradish peroxidase (HRP), methylene green (MG) and multiwalled carbon nanotubes within ormosils; 3-aminopropyltrimethoxysilane (APTMOS), 2-(3,4-epoxycyclohexyl)ethyltrimethoxysilane (ETMOS) and phenyltrimethoxysilane (PHTMOS). APTMOS determined the hydrophilicity/hydrophobicity of the ormosils and PHTMOS and ETMOS increased the physical and mechanical strength of the ormosil matrix. The ormosil modified electrodes were characterized with SEM, UV-vis spectroscopy and electrochemical methods. Cyclic voltammetry and amperometric measurements demonstrated the MG coimmobilized with HRP in this way, displayed good stability and could efficiently shuttle electrons between immobilized enzyme and electrode, and MWCNTs facilitated the electrocatalytic reduction of H₂O₂ at reduced over potential. The Micheaelis constant of the immobilized HRP was 1.8 mM, indicating a high affinity of the HRP to H₂O₂ without loss of enzymatic activity in ormosil matrix. The prepared biosensor had a fast response of H₂O₂, less than 10 s, and excellent linear range of concentration from 5 × 10⁻⁷ to 2 × 10⁻⁵ M with the detection limit of 0.5 μM (S/N = 3) under the optimum conditions. At the same time, the influence of solution pH, effect of enzyme amount, steady-state applied potential and temperature on the biosensor were investigated. The enzyme electrode retained about 90% of its initial activity after 30 days of storage in a dry state at 4 °C. The preparation of the developed biosensor was convenient and showed high sensitivity with good stability.     

Development of an automatic multi-channel ink-jet ejection chemiluminescence system and its application to the determination of horseradish peroxidase

In this work, an automatic multi-channel ink-jet for chemiluminescence (CL) analysis was developed. The four-channel ink-jet device was controlled by a home-made circuit. Differing from the classic flow injection CL, the whole procedure for CL analysis was automatically completed on a hydrophobic glass side. CL reaction of luminal and hydrogen peroxide for the determination of horseradish peroxidase (HRP) was selected as an application to automatic CL analysis platform. All solutions delivered by different channels were precisely ejected to the same position of the glass slide for the CL analysis. The consumption of reaction solution was reduced to nanoliter level. The whole CL analysis could be completed in less than 4 min, which was benefited from the prompt solution mixing in small size of droplet. The CL intensity increased linearly with HRP concentration in the range from 0.01 to 0.5 μg mL⁻¹. The limit of detection (LOD) (S/N = 3) was 0.005 μg mL⁻¹. Finally, the automatic CL system could also be used for the detection of HRP in HRP–protein conjugates, which showed its practical application in immunoassay.     

Immobilized anthraquinone for redox mediation of horseradish peroxidase for hydrogen peroxide sensing

The detection of hydrogen peroxide is detailed using horseradish peroxidase and anthraquinone. Both species are immobilized on a glassy carbon electrode substrate. This dual immobilization gives rise to lower detection limits compared with the situation when either of the species is immobilized. Detection limits of 40 nM are reported within physiologically-relevant media.     

Development of hydrogen peroxide biosensor based on in situ covalent immobilization of horseradish peroxidase by one-pot polysaccharide-incorporated sol-gel process

A simple and reliable one-pot approach was established for the development of a novel hydrogen peroxide (H₂O₂) biosensor based on in situ covalent immobilization of horseradish peroxidase (HRP) into biocompatible material through polysaccharide-incorporated sol-gel process. Siloxane with epoxide ring and trimethoxy anchor groups was applied as the bifunctional cross-linker and the inorganic resource for organic-inorganic hybridization. The reactivity between amine groups and epoxy groups allowed the covalent incorporation of HRP and the functional biopolymer, chitosan (CS) into the inorganic polysiloxane network. Some experimental variables, such as mass ratio of siloxane to CS, pH of measuring solution and applied potential for detection were optimized. HRP covalently immobilized in the hybrid matrix possessed high electrocatalytic activity to H₂O₂ and provided a fast amperometric response. The linear response of the as-prepared biosensor for the determination of H₂O₂ ranged from 2.0 × 10⁻⁷ to 4.6 × 10⁻⁵ mol l⁻¹ with a detection limit of 8.1 × 10⁻⁸ mol l⁻¹. The apparent Michaelis-Menten constant was determined to be 45.18 μmol l⁻¹. Performance of the biosensor was also evaluated with respect to possible interferences. The fabricated biosensor exhibited high reproducibility and storage stability. The ease of the one-pot covalent immobilization and the biocompatible hybrid matrix serve as a versatile platform for enzyme immobilization and biosensor fabricating.     

Stacked films immobilization of MBTH in nafion/sol-gel silicate and horseradish peroxidase in chitosan for the determination of phenolic compounds

The stacked-film immobilization of 3-methyl-2-benzothiazolinone hydrazone (MBTH) in hybrid nafion/sol-gel silicate film and horseradish peroxidase (HRP) in chitosan, performed in order to allow the determination of phenolic compounds, was investigated via an optical method. The stacked films were deposited onto a microscope glass slide by a spin-coating technique. The quinone or free radical product formed by the enzymatic reactions of phenolic compounds interacts with MBTH to form azo-dye products, which can be measured spectrophotometrically at a wavelength of 500 nm. The color intensity of the product was found to increase in proportion to the phenolic concentration after 5 min of exposure. The response of the biosensor was linear over concentration ranges of 0.025–0.500, 0.010–0.070 and 0.050–0.300 mM for guaiacol, resorcinol and o-cresol, respectively, and gave detection limits of 0.010, 0.005 and 0.012 mM. The sensor exhibited good sensitivity and stability for at least two months.     

Effect of tetrabutylammonium bromide on enzymatic polymerization of phenol catalyzed by horseradish peroxidase

In this article tetrabutylammonium bromide （TBAB） was first added in buffer to compose a convenient and environmentally friendly system, and enzymatic polymerization of phenol catalyzed by horseradish peroxidase （HRP） could proceed efficiently in this system. When TBAB was added, the most conversion of phenol could reach 99.1%. The phenol polymer was considered to consist of a mixture of phenylene （Ph） and oxyphenylene （Ox） units by IR analysis, and the ratio of phenylene to oxyphenylene units （Ph/Ox） was measured by titration. Moreover, the effects of the dosage of horseradish peroxidase （HRP） and pH value on the conversion of phenol were investigated. The reaction performed very effectively in this novel system when the addition of HRP was only 0.2 mg. In all cases, the weight-average molecular weight calculated by GPC-SLS was in a range from 12000 Da to 30000 Da. The phenol polymer prepared in the present research possessed good thermal stability shown by TG analysis.     

Mesoporous silica hollow sphere (MSHS) for the bioelectrochemistry of horseradish peroxidase

In this work, novel mesoporous silica hollow spheres (MSHS) were chosen as an immobilization matrix, to construct a mediator-free third-generation HRP biosensor. UV-vis spectroscopy revealed that horseradish peroxidase (HRP) entrapped in MSHS could retain its native structure. FTIR spectroscopy and nitrogen adsorption-desorption isotherms indicated that HRP are intercalated into the mesopores. The direct electron transfer of HRP entrapped in MSHS was observed. A pair of stable and well-defined redox peaks of HRP with a formal potential of about −0.150 V (vs. Ag/AgCl) in 0.1 M pH 7.0 phosphate-buffered solution (PBS) were obtained. The biosensor exhibited a fast amperometric response to H₂O₂ with a linear range of 3.9 × 10⁻⁶ to 1.4 × 10⁻⁴ M (R = 0.997, N = 20). The detection limit was 1.2 × 10⁻⁶ M based S/N = 3.     

An amperometric horseradish peroxidase inhibition biosensor for the determination of phenylhydrazine

An amperometric horseradish peroxidase (HRP) inhibition biosensor has been substantially constructed by the help of N,N-dicyclohexylcarbodiimide (DCC), N-hydroxysuccinimide (NHS). The preparation steps and the biosensor response to phenylhydrazine were monitored by electrochemical impedance spectroscopy (EIS), cyclic voltammetry, and chronoamperometry. The proposed biosensor could be applied to determine phenylhydrazine in a 0.10 M phosphate buffer solution containing 1.2 mM hydroquinone and 0.50 mM H(2)O(2) by phenylhydrazine, inhibiting the catalytic activity of the HRP enzyme in the reduction of H(2)O(2). The system was optimized to realize a reliable determination of phenylhydrazine in the range of 2.5 x 10(-7) to 1.1 x 10(-6) M with a detection limit of 8.2 x 10(-8) M and a correlation coefficient of 0.999. The modified electrode displayed good reproducibility, sensitivity and stability for the determination of phenylhydrazine.