Chemiluminometric determination of carvedilol in a multi-pumping flow system

In this work a simple, fast, sensitive and selective flow-based procedure for the chemiluminometric determination of carvedilol, a recent non-cardioselective β-blocker with noteworthy antioxidant activity, is proposed. The developed methodology takes advantage of the antioxidant capacity of carvedilol to inhibit the chemiluminescence response resulting from the oxidation of luminol by hypochlorite, by acting as a hypochlorite scavenger. The analytical process was implemented in a multi-pumping flow system that employs multiple solenoid actuated micro-pumps as the only active components. These acted as solution insertion, propelling and commuting units assuring an easily controlled, low cost, compact and reliable analytical system.A linear working range for carvedilol concentrations ranging from 1.2 × 10⁻⁷ to 3.0 × 10⁻⁶ mol l⁻¹ (r > 0.999, n = 6), was obtained, with a detection limit of 8.7 × 10⁻⁹ mol l⁻¹. The system handles about 65 samples per hour yielding precise results (R.S.D. < 1.3%, n = 10). Recoveries within 95 and 104% were obtained.     

A catalytic multi-pumping flow system for the chemiluminometric determination of metformin

A multi-pumping flow system for the chemiluminometric determination of the hypoglycaemic drug metformin was implemented. The developed methodology was based on the metformin-induced inhibition (metformin acts as a Cu(II) scavenger) of the catalytic effect of Cu(II) ions on the chemiluminescent reaction between luminol and hydrogen peroxide. The flow manifold configuration was based on the utilisation of multiple solenoid-actuated micro-pumps that were simultaneously accountable for sample/reagent introduction and reaction zone formation/propulsion, thus resulting in a fully automated, simple and highly selective multi-pumping flow system. A versatile sample manipulation allowed the establishment of distinct sampling strategies with low reagent consumption. The characteristic pulsed flow ensured an effective sample/reagent mixing leading to a better and faster reaction zone homogenisation and thus improved analytical signals. Linear calibration plots were obtained for metformin hydrochloride concentrations ranging from 5 to 15 mg L^–1 with a relative standard deviation lower than 2.0% (n=5). Detection limit was 0.94 mg L^–1, and the sampling rate was about 95 determinations per hour. The developed methodology was applied to the analysis of pharmaceutical formulations and the obtained results were in agreement with those furnished by the reference method with relative percentage deviations of lower than 1.5%.     

Direct chemiluminescence determination of cysteine in human serum using quinine-Ce(IV) system

A simple, sensitive and selective chemiluminescence (CL) method was developed for the determination of cysteine. This method is based on that the weak CL of cysteine oxidized with cerium (IV) can be greatly enhanced by quinine. The calibration curve was linear over the range 3.5×10⁻⁹-3.5×10⁻⁶ M with a detection limit of 2.5×10⁻⁹ M (S/N=3). The RSD was found to be 8.4% by 10 replicate determinations of 2.9×10⁻⁸ M cysteine. Due to high sensitivity, the proposed method can be used directly to determine the total concentration of cysteine in human serum through simply diluting the sample for a thousand fold. The obtained result was in agreement with that given by amino acid autoanalyzer. The present method does not require any separation, showing a simpler analytical characteristic. The mechanism of the CL reaction was also discussed.     

Greener analytical method for the determination of copper(II) in wastewater by micro flow system with optical sensor

Greener analytical method using micro flow system for the determination of Cu(II) in wastewater samples was designed and investigated. The micro flow system consisted of a planar glass chip with poly(dimethylsiloxane) (PDMS) top plate and fixed with fiber optic probe as optical sensor for monitoring of Cu(II) that reacted with 2-carboxy-2′-hydroxy-5′-sulfoformazyl benzene (zincon) on the chip at 605 nm. This design gave a satisfied sensitivity with a linear calibration graph over the range of 0.1-3.0 μg mL⁻¹ of Cu(II) and correlation coefficient 0.9991. The percentage relative standard deviation was 2.5 for 10-replicate measurements and the limit of detection (LOD) was 0.1 μg mL⁻¹. This system has been successfully applied to the determination of Cu(II) in wastewaters from electroplating industry with less reagents and samples consumption and diminutive waste generation.     

Soluble manganese(IV) as a chemiluminescence reagent for the determination of opiate alkaloids, indoles and analytes of forensic interest

We present the results of our investigations into the use of soluble manganese(IV) as a chemiluminescence reagent, which include a significantly faster method of preparation and a study on the effect of formaldehyde and orthophosphoric acid concentration on signal intensity. Chemiluminescence detection was applied to the determination of 16 analytes, including opiate alkaloids, indoles and analytes of forensic interest, using flow injection analysis methodology. The soluble manganese(IV) reagent was less selective than either acidic potassium permanganate or tris(2,2′-bipyridyl)ruthenium(III) and therefore provided a more universal chemiluminescence detection system for HPLC. A broad spectral distribution with a maximum at 730 ± 5 nm was observed for the reaction between the soluble manganese(IV) and a range of analytes, as well as the background emission from the reaction with the formaldehyde enhancer. This spectral distribution matches that reported for chemiluminescence reactions with acidic potassium permanganate, where a manganese(II) emitting species was elucidated. This provides further evidence that the emission evoked in reactions with soluble manganese(IV) also emanates from a manganese(II) species, and not bimolecular singlet oxygen as suggested by previous authors.     

Multi-pumping flow system for the determination of dissolved orthophosphate and dissolved organic phosphorus in wastewater samples

A multi-pumping flow system (MPFS) for the spectrophotometric determination of dissolved orthophosphate and dissolved organic phosphorus in wastewater samples is proposed. The determination of orthophosphate is based on the vanadomolybdate method. In-line ultraviolet photo-oxidation is employed to mineralise organic phosphorus to orthophosphate prior to detection. A solenoid valve allows the deviation of the flow towards the UV-lamp to carry out the determination of organic phosphorus.Calibration was found to be linear up to 20 mg P L⁻¹, with a detection limit (3s_b/S) of 0.08 mg P L⁻¹, an injection throughput of 75 injections h⁻¹ and a repeatability (R.S.D.) of 0.6% for the direct determination of orthophosphate. On the other hand, calibration graphs were linear up to 40 mg P L⁻¹, with a detection limit (3s_b/S) of 0.5 mg P L⁻¹, an injection throughput of 11 injections h⁻¹ and a repeatability (R.S.D.) inferior to 2.3% for the procedures involving UV photo-oxidation.     

Downscaling a multicommuted flow injection analysis system for the photometric determination of iodate in table salt

In this work a downscaled multicommuted flow injection analysis setup for photometric determination is described. The setup consists of a flow system module and a LED based photometer, with a total internal volume of about 170 μL. The system was tested by developing an analytical procedure for the photometric determination of iodate in table salt using N,N-diethyl-henylenediamine (DPD) as the chromogenic reagent. Accuracy was accessed by applying the paired t-test between results obtained using the proposed procedure and a reference method, and no significant difference at the 95% confidence level was observed. Other profitable features, such as a low reagent consumption of 7.3 μg DPD per determination; a linear response ranging from 0.1 up to 3.0 m IO₃⁻, a relative standard deviation of 0.9% (n = 11) for samples containing 0.5 m IO₃⁻, a detection limit of 17 μg L⁻¹ IO₃⁻, a sampling throughput of 117 determination per hour, and a waste generation 600 μL per determination, were also achieved.     

Multi-pumping flow system for the determination, solid-phase extraction and speciation analysis of iron

A multi-pumping flow system (MPFS) for the spectrophotometric determination, solid-phase extraction (SPE) and speciation analysis of iron at a wide range of concentrations is proposed. Chelating (iminodiacetic groups) disks have been used as solid phase. A solenoid valve allows the deviation of the flow towards the chelating disk to carry out SPE procedures. The possibility to combine solenoid micro-pumps with solenoid valves increases the versatility of MPFS. Ammonium thiocyanate has been chosen as chromogenic reagent for Fe(III). The determination of total iron is achieved by the on-line oxidation of iron(II) to iron(III) with a hydrogen peroxide stream.

A mass calibration was run within the range 0.01–1.75 μg. The detection limit (3s_b/S) was 0.01 μg. The repeatability (R.S.D.) was estimated as 1.6% after 10-fold processing of 2 ml of 0.5 mg l⁻¹ Fe solution. When SPE was not required, two linear calibration graph within the ranges 0.05–10 and 0.2–15 mg l⁻¹ for the determination of iron(III) and total iron, respectively, were obtained. The proposed procedure was validated by analysis of certified reference materials. The analytical features were compared with those obtained exploiting MSFIA.     

A flow-injection chemiluminescence method for the determination of some estrogens by enhancement of luminol-hydrogen peroxide-tetrasulfonated manganese phthalocyanine reaction

A novel flow-injection chemiluminescence (FI-CL) method for the determination of estrogens is proposed, based upon its enhancing effect on the CL reaction of luminol with hydrogen peroxide catalyzed by tetrasulfonated manganese phthalocyanine (MnTSPc) in alkaline solution. Under the selected experimental conditions, a linear relationship was obtained between the CL intensity and the concentration of estrone in the range of 1.0 × 10⁻⁷ to 1.0 × 10⁻⁶ mol/l, estradiol in the range of 9.0 × 10⁻⁸ to 1.0 × 10⁻⁶ mol/l and estriol in the range of 3.0 × 10⁻⁷ to 2.0 × 10⁻⁶ mol/l, respectively. The detection limits were 5.1 × 10⁻⁸ mol/l for estrone, 7.2 × 10⁻⁹ mol/l for estradiol and 6.5 × 10⁻⁸ mol/l for estriol with a relative standard deviation of 2.8% for 5.0 × 10⁻⁷ mol/l estrone, 2.4% for 1.0 × 10⁻⁷ mol/l estradiol, and 3.1% for 7.0 × 10⁻⁷ mol/l estriol (n = 11). This method has been applied to the determination of estrogen in pharmaceutical injections and tap water with satisfactory results.     

Automatic flow system for the sequential determination of copper in serum and urine by flame atomic absorption spectrometry

In this work, a fully automated flow system exploiting the advantages of the association of multi-pumping, multicommutation, binary sampling and merging zones, to accomplish the sequential determination of copper in serum and urine by flame atomic absorption spectrometry, is described. The developed flow system allowed multiple tasks, such as serum samples preparation (samples and standard solutions viscosity adjustment), serum copper (SCu) measurement, urine copper (UCu) pre-concentration and its subsequent elution and measurement, to be carried out sequentially. The implemented flow manifold presented a modular configuration consisting on two quasi-independent modules, each one accountable for a specific sample manipulation and whose combined operation under computer control enabled the determination of copper in a wide concentrations range.Once optimised and with a sample consumption of about 0.250 mL of serum and 7 mL of urine, the developed flow system allowed linear calibration plots up to 5 mg L⁻¹ with a detection limit of 0.035 mg L⁻¹ for SCu and linear calibration plots up to 300 μg L⁻¹ with a detection limit of 0.67 μg L⁻¹ for UCu. The sampling rate varied according to the module employed and was about 360 determinations h⁻¹ (SCu module), 12 determinations h⁻¹ (UCu module) or 24 determinations h⁻¹ (12 urine and 12 serum samples; UCu and SCu modules simultaneously). Repeatability studies (R.S.D.%, n = 10) showed good precision for UCu at concentrations of 25 μg L⁻¹ (2.54%), 50 μg L⁻¹ (0.90%) and 100 μg L⁻¹ (1.62%) as well as for SCu at concentrations of 0.25 mg L⁻¹ (8.11%), 1 mg L⁻¹ (3.11%) and 5 mg L⁻¹ (0.90%). A comparative evaluation showed a good agreement between the results obtained in the analysis of UCu and SCu (n = 18) by both the developed methodology and the reference procedures. Accuracy was further evaluated by means of the analysis of reference samples (Seronorm™ Trace Elements Urine and Seronorm™ Trace Elements Serum) and the obtained results complied with the certified values.     

Flow injection chemiluminescence determination of the total phenolics levels in plant-derived beverages using soluble manganese(IV)

This study established a flow injection (FI) methodology for the determination of the total phenolic content in plant-derived beverages based on soluble manganese(IV) chemiluminescence (CL) detection. It was found that mixing polyphenols with acidic soluble manganese(IV) in the presence of formaldehyde evoked chemiluminescence. Based on this finding, a new FI-CL method was developed for the estimation of the total content of phenolic compounds (expressed as milligrams of gallic acid equivalent per litre of drink) in a variety of wine, tea and fruit juice samples. The proposed method is sensitive with a detection limit of 0.02 ng mL⁻¹ (gallic acid), offers a wide linear dynamic range (0.5-400 ng mL⁻¹) and high sample throughput (247 samples h⁻¹). The relative standard deviation for 15 measurements was 3.8% for 2 ng mL⁻¹ and 0.45% for 10 ng mL⁻¹ of gallic acid. Analysis of 36 different samples showed that the results obtained by the proposed FI-CL method correlate highly with those obtained by spectrophotometric methods commonly used for the evaluation of the total phenolic/antioxidant level. However, the FI-CL method was found to be far simpler, more rapid and selective, with almost no interference from non-phenolic components of the samples examined.     

A novel flow injection chemiluminescence determination of Cr(VI) with Dichlorotris(1,10-phenanthroline)ruthenium(II)

A selective novel reverse flow injection system with chemiluminescence detection (rFI-CL) for the determination of Cr(VI) in presence of Cr(III) with Dichlorotris (1,10-phenanthroline)ruthenium(II), (Ru(phen)₃Cl₂), is described in this work. This new method is based on the oxidation capacity of Cr(VI) in H₂SO₄ media. First, the Ruthenium(II) complex is oxidized to Ruthenium(III) complex by Cr(VI) and afterwards it is reduced to the excited state of the Ruthenium(II) complex by a sodium oxalate solution, emitting light inside the detector. The intensity of chemiluminescence (CL) is proportional to the concentration of Cr(VI) and, under optimum conditions, it can be determined over the range of 3-300 μg L⁻¹ with a detection limit of 0.9 μg L⁻¹. The RSD was 8.4% and 1.5% at 5 and 50 μg L⁻¹, respectively. For the rFI-CL method various analytical parameters were optimized: flow rate (1 mL min⁻¹), H₂SO₄ carrier concentration (20% w/V), Ru(phen)₃Cl₂ concentration (5 mM) and sodium oxalate concentration (0.1 M). The effect of Cr(III), Fe(III), Al(III), Cd(II), Zn(II), Hg(II), Pb(II), Ca(II) and Mg(II), was studied. The method is highly sensitive and selective, allowing a fast, on-line determination of Cr(VI) in the presence of Cr(III). Finally, the method was tested in four different water samples (tap, reservoir, well and mineral), with good recovery percentage.     

Piezoelectric pumping in flow analysis: Application to the spectrophotometric determination of gabapentin

Solutions propelling devices are fundamental components of a flow-based analytical manifold. In this work different manifold configurations were implemented to evaluate the performance of multiple piezoelectric micro-pumps used as solutions insertion and propulsion devices. The micro-pumps are piezo-actuated micro-diaphragm pumps with passive check valves characterised by a small compact size and low power demands, and are able to produce reproducible flow rates of up to 4 mL min⁻¹. The flow rate is controlled by the frequency of the piezoelectric actuator (up to 20 Hz). As an additional feature, piezoelectric micro-pumps actuation generates a pulsed flowing stream that ensures a faster sample/reagent mixing contributing to improved reaction development.

The developed flow approach was assessed in the spectrophotometric determination of gabapentin in pharmaceutical preparations upon reaction with 1,2-naphthoquinone-4-sulfonate in alkaline medium. Distinct flow manifold configurations were designed for achievement of different solutions management. Linear calibrations plots for gabapentin concentrations of up to 150 mg L⁻¹, with relative standard deviations of less than 1.50% (n = 10) and a sample throughput of about 28 determinations per hour, were obtained.     

Flow-injection chemiluminescence determination of ascorbic acid by use of the cerium(IV)-Rhodamine B system

A highly sensitive flow-injection (FI) method with chemiluminescence (CL) detection is used for the determination of l-ascorbic acid. The method is based on the CL reaction of Rhodamine B with cerium(IV) in sulfuric acid media. l-Ascorbic acid is suggested to be a catalyst utilized in the energy-transferred excitation process. The proposed procedure allows quantitation of l-ascorbic acid in the range 3.8×10⁻¹³ to 1.0×10⁻¹⁰ mol l⁻¹ with a correlation coefficient of 0.9998 (n=5) and relative standard deviation (R.S.D.) of 0.92% (n=11) at 1.0×10⁻¹¹ mol l⁻¹. The detection limit (3×blank) was 1.0×10⁻¹³ mol l⁻¹. The method is successfully used to determine l-ascorbic acid in fresh vegetables. The possible mechanism of the chemiluminescence in the system is discussed.     

Flow-through solid-phase based optical sensor for the multisyringe flow injection trace determination of orthophosphate in waters with chemiluminescence detection

In this work, a novel flow-through solid-phase based chemiluminescence (CL) optical sensor is described for the trace determination of orthophosphate in waters exploiting the multisyringe flow injection analysis (MSFIA) concept with multicommutation. The proposed time-based injection flow system relies upon the in-line derivatisation of the analyte with ammonium molybdate in the presence of vanadate, and the transient immobilisation of the resulting heteropolyacid in a N-vinylpyrrolidone/divinylbenzene copolymer packed spiral shape flow-through cell located in front of the window of a photomultiplier tube. The simultaneous injection of well-defined slugs of luminol in alkaline medium and methanol solution towards the packed reactor is afterwards performed by proper switching of the solenoid valves. Then, the light emission from the luminol oxidation by the oxidant species retained onto the sorbent material is readily detected. At the same time, the generated molybdenum-blue compound is eluted by the minute amount of injected methanol, rendering the system prepared for a new measuring cycle. Therefore, the devised sensor enables the integration of the solid-phase CL reaction with elution and detection of the emitted light without the typical drawbacks of the molybdenum-blue based spectrophotometric procedures regarding the excess of molybdate anion, which causes high background signals due to its self-reduction. The noteworthy features of the developed CL-MSFIA system are the feasibility to accommodate reactions with different pH requirements and the ability to determine trace levels of orthophosphate in high silicate content samples (Si/P ratios up to 500). Under the optimised conditions, a dynamic linear range from 5 to 50 μg P l⁻¹ for a 1.8 ml sample, repeatability better than 3.0% and a quantification limit of 4 μg P l⁻¹ were attained. The flowing stream system handles 11 analysis h⁻¹ and has been successfully applied to the determination of trace levels of orthophosphate in environmental samples such as mineral, ground, tap and pond waters as well as samples from a water-steam cycle of an incineration plant. The t-test comparison of the means for the developed optical sensor and the molybdenum-blue spectrophotometric APHA/AWWA/WPCF reference method revealed that there is no evidence of significant differences between the obtained results at the 95% confidence level.     

A dispersive liquid-liquid microextraction procedure for determination of boron in water after ultrasound-assisted conversion to tetrafluoroborate

A novel, simple and green procedure is presented for the determination of boron. The method is based on ultrasound-assisted conversion of boron to tetrafluoroborate anion and the formation of an ion pair between BF₄⁻ and Astra Phloxine reagent (R), followed by dispersive liquid-liquid microextraction of the ion pair formed and subsequent UV-vis spectrophotometric detection. The conversion of boron to tetrafluoroborate anion is performed in an acidic medium of 0.9 mol L⁻¹ H₂SO₄ in the presence of 0.1 mol L⁻¹ F^- by means of 10 min of ultrasonication. The extraction of the ion pair formed between BF₄⁻ and R (1 × 10⁻⁴ mol L⁻¹ R) is carried out by dispersive liquid-liquid microextraction using 0.5 mL of amyl acetate (as extraction solvent), tetrachloromethane (as auxiliary solvent) and acetonitrile (as dispersive solvent) in a ratio of 1:1:2. The absorbance of the coloured extracts obeys Beer's law in the range 0.22-18.7 mg L⁻¹ of B(III) at 553 nm wavelength. The limit of detection calculated from a blank test (n = 10) based on 3 s is 0.015 mg L⁻¹ of B(III). The method was applied to the determination of boron in mineral waters.     

Simultaneous determination of quercetin, kaempferol, and isorhamnetin in phytopharmaceuticals of Hippophae rhamnoides L. by high-performance liquid chromatography with chemiluminescence detection

A novel method based on reversed-phase high-performance liquid chromatography with chemiluminescence detection has been developed for the simultaneous determination of three flavonols including quercetin, kaempferol, and isorhamnetin. The procedure was based on the chemiluminescent enhancement by flavonols of the cerium(IV)-rhodamine 6G system in sulfuric acid medium. The effects of several parameters on the HPLC resolution and CL emission were studied systematically. Good separation was achieved with isocratic elution using a mixture of methanol and aqueous 1.0% acetic acid (37:63, v/v) within 25 min. Under optimized conditions, the linear working range covers 3 orders of magnitude with relative standard deviations below 4.5% for 11 replicate injected flavonol samples, and detection limits (S/N= 3) were 1.6 x 10(-8), 3.5 x 10(-9), and 6.5 x 10(-9) g mL(-1) for quercetin, kaempferol, and isorhamnetin, respectively. The chemiluminescence reaction was compatible with the mobile phase of high-performance liquid chromatography. The proposed method has been successfully applied to the determination of three active flavonols in phytopharmaceuticals of Hippophae rhamnoides L. After a simple extraction procedure, the repeatability and recovery were satisfactory.     

Chemiluminescence method for the determination of mitoxantrone by the enhancement of the tris-(4,7-diphenyl-1,10-phenanthrolinedisulfonic acid)ruthenium(II)–cerium(IV) system

2,5-Dimercapto-1,3,4-thiadiazole (DMTD) self-assembled monolayer on gold electrode was prepared and investigated by electrochemical measurement. The DMTD/Au electrode exhibited a significantly increased sensitivity and selectivity for Pb(II) in acetate buffer (pH 5.5) at a potential of −1.0 V (vs Ag/AgCl) for 4 min by anodic stripping voltammetry. The influence of various experimental parameters on the voltammetric response was studied. Under the optimized working conditions, the dependence of the stripping peak current response on concentration of Pb(II) was linear in the range of 1–45 μmol L⁻¹ with a correlation coefficient of 0.9988, and the detection limit was 0.10 μmol L⁻¹. The relative standard deviation of the results was 3.4% for six successive determinations of a 20 μmol L⁻¹ Pb(II) solution. A study of interfering substances was also performed. The method was applied to the determination of Pb(II) in water samples with satisfactory results. Correspondence: Hong Qun Luo, School of Chemistry and Chemical Engineering, Southwest University, 400715 Chongqing, China     

Multisyringe flow injection analysis hyphenated with liquid core waveguides for the development of cleaner spectroscopic analytical methods: improved determination of chloride in waters

In this work, the hyphenation of the multisyringe flow injection analysis technique with a 100-cm-long pathlength liquid core waveguide has been accomplished. The Cl⁻/Hg(SCN)₂/Fe³⁺ reaction system for the spectrophotometric determination of chloride (Cl⁻) in waters was used as chemical model. As a result, this classic analytical methodology has been improved, minimizing dramatically the consumption of reagents, in particular, that of the highly biotoxic chemical Hg(SCN)₂. The proposed method features a linear dynamic range composed of two steps between (1) 0.2–2 and (2) 2–8 mg Cl⁻ L⁻¹, thus extended applicability due to on-line sample dilution (up to 400 mg Cl⁻ L⁻¹). It also presents improved limits of detection and quantification of 0.06 and 0.20 mg Cl⁻ L⁻¹, respectively. The coefficient of variation and the injection throughput were 1.3% (n = 10, 2 mg Cl⁻ L⁻¹) and 21 h⁻¹. Furthermore, a very low consumption of reagents per Cl⁻ determination of 0.2 μg Hg(II) and 28 μg Fe³⁺ has been achieved. The method was successfully applied to the determination of Cl⁻ in different types of water samples. Finally, the proposed system is critically compared from a green analytical chemistry point of view against other flow systems for the same purpose.     

Single interface flow system with potentiometric detection for the determination of nitrate in water and vegetables

In this work a single interface flow system (SIFA) with potentiometric detection was for the first time implemented and applied to the determination of nitrate in waters and plant extracts. The analytical potential of the SIFA system was exploited not only to transport the sample towards detection but also to carry out, in a reproducible and automated way, the tasks associated with sample pre-treatment, namely ionic strength, pH adjustment and interfering species suppression. The advantageous aspects of combining a SIFA system with potentiometry with enhanced simplicity, ease of implementation and automation were further discussed and emphasised.The obtained results showed relative deviations lower than 5%, for both types of samples, with sampling rates of about 40 h⁻¹.In addition, an innovative and straightforward process for constructing plastic membrane ion selective electrodes with a tubular configuration able to be coupled to flow-based analytical systems is also proposed. The developed approach, consisting of assembling the electrode inside a flow tubing connector is very simple to implement, robust, particularly adequate to be combined with flow methodologies and maintains all dynamic and analytical characteristics exhibited by previous assembling processes.