Electromembrane extraction of basic drugs from untreated human plasma and whole blood under physiological pH conditions

The present work describes the first systematic study of electromembrane extraction (EME) from biological matrices under physiological conditions. Six basic drugs with protein binding in the range of 20–97% were extracted from untreated human plasma and whole blood through a supported liquid membrane (SLM) consisting of 1-ethyl-2-nitrobenzene impregnated in the walls of a hollow fiber, and into an acidified aqueous solution inside the lumen of the fiber. The electrical potential difference over the membrane reduced the protein binding of the drugs and transported the free drug fraction over the membrane. Recoveries in the range 25–65% were obtained with 10-min extraction time and an applied voltage of only 10 V over the SLM. Interday precision better than 20% RSD and linearity in the range 0.5–10 μg/mL were obtained for nortriptyline and methadone. Extraction from untreated whole blood was also demonstrated with recoveries in the range 19–51%.     

Electromembrane extraction of peptides--fundamental studies on the supported liquid membrane

A large screening of different components in the supported liquid membrane (SLM) in electromembrane extraction (EME) was performed to test the extraction efficiency on eight model peptides. Electromembrane extraction from a 500 μL acidified aqueous sample containing the model peptides in the concentration 10 μg/mL was used. Extraction time was 5 min with an electric potential of 10 V and 900 rpm agitation of the sample vial. The samples were extracted through a hollow fiber-based SLM with different compositions of organic solvents and carriers. A small volume of acidified acceptor solution (25 μL) was after extraction analyzed directly, or with some dilution, on CE or HPLC. This article has identified mono- or di-substituted phosphate groups as the prominent group of carrier molecules needed to obtain acceptable recoveries. For the organic solvents, primary alcohols and ketones have shown promise regarding recovery and reproducibility, with some differences in selectivity. A new composition of the SLM, namely 2-octanone and tridecyl phosphate (90:10 w/w) has proved to give higher extraction recoveries and lower standard deviation than SLMs previously reported in the literature.     

Drop-to-drop microextraction across a supported liquid membrane by an electrical field under stagnant conditions

Electromembrane extraction (EME) of basic drugs from 10 μL sample volumes was performed through an organic solvent (2-nitrophenyl octyl ether) immobilized as a supported liquid membrane (SLM) in the pores of a flat polypropylene membrane (25 μm thickness), and into 10 μL 10 mM HCl as the acceptor solution. The driving force for the extractions was 3–20 V d.c. potential sustained over the SLM. The influence of the membrane thickness, extraction time, and voltage was investigated, and a theory for the extraction kinetics is proposed. Pethidine, nortriptyline, methadone, haloperidol, and loperamide were extracted from pure water samples with recoveries ranging between 33% and 47% after only 5 min of operation under totally stagnant conditions. The extraction system was compatible with human urine and plasma samples and provided very efficient sample pretreatment, as acidic, neutral, and polar substances with no distribution into the organic SLM were not extracted across the membrane. Evaluation was performed for human urine, providing linearity in the range 1–20 μg/mL, and repeatability (RSD) in average within 12%.     

Solid phase extraction of zinc(II) using a PVC-based polymer inclusion membrane with di(2-ethylhexyl)phosphoric acid (D2EHPA) as the carrier

A polymer inclusion membrane (PIM) is reported consisting of 45% (m/m) di(2-ethylhexyl)phosphoric acid (D2EHPA) immobilized in poly(vinyl chloride) (PVC) for use as a solid phase absorbent for selectively extracting Zn(II) from aqueous solutions in the presence of Cd(II), Co(II), Cu(II), Ni(II) and Fe(II). Interference from Fe(III) in the sample is eliminated by precipitation with orthophosphate prior to the extraction of Zn(II). Studies using a dual compartment transport cell have shown that the Zn(II) flux (2.58 × 10⁻⁶ mol m⁻² s⁻¹) is comparable to that observed for supported liquid membranes. The stoichiometry of the extracted complex is shown to be ZnR₂·HR, where R is the D2EHPA anion.     

Reversed phase partition chromatographic separation of antimony (III) with bis(2-ethylhexyl) phosphoric acid

A new method is proposed for the extractive Chromatographic separation of antimony. Antimony is extracted from 0.001–0.5M hydrochloric acid by a silica gel column coated with bis (2-ethylhexyl) phosphoric acid stripped with 2–8M hydrochloric, nitric or sulphuric acid, and determined spectrophotometrically at 555 nm as its complex with phenylfluorone. Antimony can thus be separated from a large number of elements, including iron, manganese, copper and thallium. Arsenic, antimony, bismuth and tin can be sequentially separated.     

Fast,selective, and sensitive analysis of low-abundance peptides in human plasma by electromembrane extraction

A totally new concept based on electrokinetic migration was evaluated for the extraction of three biologically active peptides from human plasma. Angiotensin 2, leu-enkephalin, and endomorphin 1 migrated from a diluted human plasma sample (2 mL, positive electrode), through a supported liquid membrane (SLM) of 1-octanol, di-isobutylketon, and di-(2-ethylhexyl) phosphate (DEHP) (55:35:10, w/w/w), and into an acidified acceptor solution (25 μL 50 mM HCl, negative electrode) by the application of an electrical potential (20 V) across the SLM. After only five min of extraction, the acceptor solution was injected and analyzed directly by liquid chromatography. The three peptides were quantified by tandem mass spectrometry, with acceptable linearity ranging from 100.0 to 1000.0 pg mL⁻¹ (r² in the range 0.9736–0.9988), and repeatability (RSD) ranging between 15% and 24% (n = 5), using plasma spiked with the three peptides in 100 pg mL⁻¹ concentration. The estimated detection limits (S/N ratio of 3:1) for angiotensin 2, leu-enkephalin, and endomorphin 1, were 60, 24, and 24 pg mL⁻¹, respectively. With this novel approach based on electromembrane extraction (EME) coupled to LC–MS/MS, endogenous concentrations of the peptides were detected in non-spiked human plasma samples, with a total analysis time less than 50 min. These experimental findings were highly interesting, and showed the opportunities for EME with regard to future peptide extractions.     

Metallacrown ethers with a symmetric bis(phosphite) ligand derived from 1,2-bis-(2-hydroxyethoxy)benzene: Synthesis, characterization and hydroformylation of styrene

To better understand the effects of ligand configuration on hydroformylation reactions carried out in the presence of LiBPh₄·3dme (dme = 1,2-dimethoxyethane), a conformationally restrained bis(phosphite) ligand derived from 1,2-bis-(2-hydroxyethoxy)benzene, {[(2,2′-O₂C₁₂H₈)P(C₂H₄O₂)]₂C₆H₄}, 1, has been prepared and its Rh(I) metallacrown ether complex has been evaluated as a catalyst for the hydroformylation of styrene. Both the activity and regioselectivity of the catalyst are sensitive to the amount of the LiBPh₄·3dme added with the activity decreasing by 16% and the regioselectivity for the iso increasing by 9% at a 8:1 LiBPh₄:Rh ratio.Model complexes for the octahedral, cis-Mo(CO)₄(1), 2, and square planar, cis-PtCl₂(1), 3, and cis-PdCl₂(1), 4, complexes in the catalytic cycle has been have been studied using multinuclear NMR spectroscopy and X-ray crystallography. Although the X-ray crystal structure of 2 suggests that the metallacrown ether ring could adopt a configuration capable of binding alkali metal cations, this does not appear to occur in a dichloromethane-d₂ solution of 2 because no shift in the ³¹P NMR resonance 2 is observed upon the addition of an excess of LiBPh₄·3dme. The ³¹P{¹H} NMR spectra of chloroform-d solutions of 2 (in the presence of a catalytic amount of HgCl₂) and of 4 and the X-ray crystal structures of the complexes indicate that the bis(phosphite) ligands are cis coordinated in these complexes in both the solution and in the solid state. This is particularly surprising for 4 because related PdCl₂{Ph₂P(CH₂CH₂O)_nCH₂CH₂PPh₂} (n = 3-5) complexes exhibit both cis-trans and monomer-oligomer equilibria in solution.     

The effect of diluents on extraction of copper(II) with di(2-ethylhexyl)phosphoric acid

The liquid–liquid extraction of copper(II) from sulfate medium with di(2-ethylhexyl)phosphoric acid (D2EHPA, HL) at 25°C is studied with the following parameters: pH, concentration of the extractant, and the nature of diluent. The effect of the diluent using polar and nonpolar solvents in the extraction of copper(II) is discussed. The extracted copper(II) species were CuL₂ in 1-octanol and methyl isobutyl ketone and CuL₂ · 2HL in toluene, carbon tetrachloride, and cyclohexane. The extraction constants are evaluated for different diluents.     

Novel preconcentration technique using bis(2-ethylhexyl) hydrogen phosphate (HDEHP) loaded porous polytetrafluoroethylene (PTFE) filter tube as a sorbent: Its application to determination of In(III) in seawater by ICP-MS with air segmented discrete sample introduction

Novel preconcetration method involving porous polytetrafluoroethylene (PTFE) filter tube impregnated bis(2-ethylhexyl) hydrogen phosphate (HDEHP) as a sorbent was studied to establish it as a practical preconcentration method for ultra trace analysis with ICP-MS. A 1 ng portion of In(III) in 1000 ml of matrix free solution or 700 ml of synthetic seawater was quantitatively complexated with HDEHP adsorbed onto porous PTFE filter tube by passing the solution through the micro pore of the filter tube. Preconcentrated In(III) was then quantitatively recovered provided that the elution, which consists of a cyclical filtering 0.1 ml of 8 mol dm⁻³ hydrochloric acid through the filter tube for 1 min; therefore, up to 10000- and 7000-fold of enrichment was attained for matrix free solution and synthetic seawater, respectively. To introduce a 0.1 ml of the eluted solution to ICP-MS, flow injection method with air segmented discrete sample introduction (ASDI) was also studied by using manually operated simple valve system. By using ASDI, good linearity of calibration curve (r = 0.99997) was observed from 0.01 to 5.0 ng ml⁻¹ of In(III). Good reproducibility was also shown in measurements of 0.1 ml of 5 ng ml⁻¹ of In(III) (R.S.D. = 1.9%, n = 5). The average recovery and R.S.D. of the results for the five duplicates determination of 0.1 ng of In(III) spiked to 200 ml of synthetic seawater were 99 and 2.4%, respectively. The method was applied to the determination of In(III) in coastal seawater sampled at north east of Hachijyo Island, Japan; using 200 ml of sample, 2000-fold preconcentration of In(III) was performed within 30 min for five samples. The analytical detection limit and the blank were 9.8 and 21 pg l⁻¹, respectively. The average concentration was determined to be 96 pg l⁻¹, and R.S.D. of the results was 3.7% (n = 3).     

Human Metabolism of Bis(2-ethylhexyl)phthalate

Abstract

To study the human metabolism of bis (2-ethylhexyl)-phthalate (DEHP) urine samples were analyzed from non-uremic psoriatic patients, uremic patients undergoing hemodialysis treatments and patients undergoing cardiac bypass surgery using High Performance Liquid Chromatography (HPLC). The urine of dialyzed non-uremic patients contained phthalic acid, mono (2-ethylhexyl) phthalate and bis (2-ethylhexyl) phthalate. Other compounds identified were p-hydroxy benzoic acid, m-hydroxy benzoic acid, o-hydroxy hippuric acid, o-hydroxy benzoic acid and benzoic acid, which may be either diet dependent normal urinary constituents or metabolites of bis (2-ethylhexyl) phthalate. The levels of phthalic acid and bis (2-ethylhexyl) phthalate found in the urine of patients who were on total body oxygenators containing a membrane during cardiac bypass surgery were comparable to levels obtained from non-uremic psoriatic patients. Significant levels of phthalic acid were detected in the urine of the uremic patients studied while mono (2-ethylhexyl) phthalate and bis (2-ethylhexyl)-phthalate were present only in small amounts or were completely absent. In general, the urinary phthalate content of uremic patients increased with urinary volume.     

Electromembrane extraction of zwitterionic compounds as acid or base: Comparison of extraction behavior at acidic and basic pHs

This study has performed on electromembrane extraction (EME) of some zwitterionic compounds based on their acidic and basic properties. High performance liquid chromatography (HPLC) equipped with UV detection was used for determination of model compounds. Cetirizine (CTZ) and mesalazine (MS) were chosen as model compounds, and each of them was extracted from acidic (as a cation) and basic (as an anion) sample solutions, separately. 1-Octanol and 2-nitrophenyl octylether (NPOE) were used as the common supported liquid membrane (SLM) solvents. EME parameters, such as extraction time, extraction voltage and pH of donor and acceptor solutions were studied in details for cationic and anionic forms of each model compound and obtained results for two ionic forms (cationic and anionic) of each compound were compared together. Results showed that zwitterionic compounds could be extracted in both cationic and anionic forms. Moreover, it was found that the extraction of anionic form of each model compound could be done in low voltages when 1-octanol was used as the SLM solvent. Results showed that charge type was not highly effective on the extraction efficiency of model compounds whereas the position of charge within the molecule was the key parameter. In optimized conditions, enrichment factors (EF) of 27–60 that corresponded to recoveries ranging from 39 to 86% were achieved.     

High-performance liquid chromatographic determination of uranium using solvent extraction and bis(salicylaldehyde) tetramethylethylenediimine as complexing reagent

The reagent bis(salicylaldehyde)tetramethylethylenediimine has been used for the determination of dioxouranium(VI), based on complexation in aqueous solution at pH 6, followed by extraction in chloroform and HPLC determination on a Hypersil ODS (3 μm) column. The complex was eluted with the ternary mixture methanol-acetonitrile-water (40:30:30, v/v/v), with UV detection at 260 nm. Oxovanadium(IV), iron(III), copper(II), cobalt(II), nickel(II) and palladium(II) were completely separated and did not interfere in the determination of uranium. The linear calibration range and detection limits have been obtained. The method has been applied to the determination of uranium together with copper, iron and nickel in mineral ore samples.     

邻苯二甲酸二(2-乙基)己酯和偏苯三酸三辛酯在临床不同药液中溶出量的比较

聚氯乙烯(PVC)材质的医疗器械产品中需要加入增塑剂以改善柔韧性,目前最常用的增塑剂是邻苯二甲酸二(2-乙基)己酯(DEHP)和偏苯三酸三辛酯(TOTM)。本文考察了PVC一次性使用输液器产品在脂溶性药液(紫杉醇注射液)、肠外营养液(脂肪乳)、酸性药液(左氧氟沙星,pH 3.0~5.0)和碱性药液(呋塞米,pH 8.0~9.0)中的DEHP和TOTM溶出量,并进行对比分析。先建立了一种高效液相色谱-紫外检测(HPLC-UV)方法测定增塑剂的溶出量,并利用该方法对增塑剂的溶出量进行了分析。实验结果表明,增塑剂在不同药液中均有一定的溶出情况,其中紫杉醇注射液对增塑剂的溶出量要高于脂肪乳,并远高于左氧氟沙星和呋塞米注射液。通过对比DEHP和TOTM的溶出量可以看出,在相同的浸提条件下,TOTM的溶出量远低于DEHP的溶出量。利用紫杉醇注射液浸提24 h,PVC输液器产品DEHP的溶出量为21.14 mg,而TOTM的溶出量仅为0.078 mg。DEHP的溶出量为TOTM溶出量的270倍。因此,TOTM具有的较好耐迁移性,是一种潜在的DEHP替代增塑剂。     

Development and application of carbon nanotubes assisted electromembrane extraction (CNTs/EME) for the determination of buprenorphine as a model of basic drugs from urine samples

In this work carbon nanotubes assisted electromembrane extraction (CNTs/EME) coupled with capillary electrophoresis (CE) and ultraviolet (UV) detection was developed for the determination of buprenorphine as a model of basic drugs from urine samples. Carbon nanotubes reinforced hollow fiber was used in this research. Here the CNTs serve as a sorbent and provide an additional pathway for solute transport. The presence of CNTs in the hollow fiber wall increased the effective surface area and the overall partition coefficient on the membrane; and lead to an enhancement in the analyte transport. For investigating the influence of the presence of CNTs in the SLM on the extraction efficiency, a comparative study was carried out between EME and CNTs/EME methods. Optimization of the variables affecting these methods was carried out in order to achieve the best extraction efficiency. Optimal extractions were accomplished with NPOE as the SLM, with 200 V as the driving force, and with pH 2.0 in the donor and pH 1.0 in the acceptor solutions with the whole assembly agitated at 750 rpm after 25 min and 15 min for EME and CNTs/EME, respectively.     

Atomic absorption determination of indium after extraction with di-(2-ethylhexyl)phosphoric acid

The equilibrium data show that indium can be quickly extracted from acidic aqueous solutions by di-(2-ethylhexyl)phosphoric acid in methyl isobutyl ketone. In this polar solvent the species ML₃·HL is extracted. The overall extraction constant is higher than that for other tervalent metals. The extraction process can be combined with AAS determination of the indium. The method is fast because stripping is not necessary, and the organic phase can be analysed directly by AAS. Use of a 51 v/v aqueous: organic phase ratio increases the sensitivity. In the pH-range used the method has good selectivity.     

Bis(2-mercaptobenzoxazolato)mercury(II) and bis(2-pyridinethiolato)mercury(II) complexes as carriers for thiocyanate selective electrodes

Highly selective poly(vinyl chloride) (PVC) membrane electrodes based on bis(2-mercaptobenzoxazolato)mercury(II) [Hg(MBO)₂] and bis(2-pyridinethiolato)mercury(II) [Hg(PT)₂] complexes as new carriers for thiocyanate-selective electrodes are reported. The electrodes were prepared by coating the membrane solution containing PVC, plasticizer, carriers and additives on the surface of graphite electrodes. Influence of the membrane composition, pH and possible interfering anions were investigated on the response properties of the electrodes. Both sensors exhibited Nernstian responses towards thiocyanate over a wide concentration range of 1×10⁻⁶ to 0.1 M, with slopes of 60.6±0.8 and 57.5±1.2 mV per decade of thiocyanate concentration for Hg(MBO)₂ and Hg(PT)₂ carriers, respectively, over a wide pH range of 3-11. The limit of detection for both electrodes was ∼6×10⁻⁷ M. The sensors have response times of ≤5 s and can be used for at least 2 months without any considerable divergence in their potential response. The proposed electrodes show fairly good discrimination of thiocyanate over several inorganic and organic anions. The electrodes were successfully applied to direct determination of thiocyanate in saliva and as indicator electrodes in precipitation titrations.     

多壁碳纳米管表面邻苯二甲酸二(2-乙基)己酯印迹聚合物的制备及其在固相萃取中的应用

以苯基修饰的多壁碳纳米管为载体,邻苯二甲酸二(2-乙基)己酯为模板分子,甲基丙烯酸为功能单体,乙二醇二甲基丙烯酸酯为交联剂,在碳纳米管表面接枝一层塑化剂邻苯二甲酸二(2-乙基)己酯印迹聚合层.采用红外光谱和扫描电镜对聚合物进行表征和分析.结果表明,在碳纳米管表面成功接枝一层20～30 nm厚的印迹聚合层.采用高效液相色谱研究该印迹聚合物的吸附性能,结果表明,碳纳米管分子印迹聚合物对邻苯二甲酸二(2-乙基)己酯最大吸附量为69.1 μmol/g,达到吸附平衡时间约为60 min.选择性吸附实验表明,与其它结构类似物相比,该印迹复合材料对邻苯二甲酸二(2-乙基)己酯有良好的识别能力.作为固相萃取材料装填于固相萃取柱中,该印迹聚合物能对芒果汁样品中塑化剂进行有效的分离和富集.     

微溶剂萃取-气相色谱-质谱法测定水中邻苯二甲酸二(2-乙基己基)酯

取水样25mL,加入无水硫酸钠3.0g,加入环己烷2.0mL,振荡萃取3min。移取萃取了邻苯二甲酸二(2-乙基己基)酯(DEHP)的上层有机相2.0μL注入HP-5毛细管柱(30m×0.32mm,0.25μm)色谱分离后进行质谱测定。DEHP的质量浓度在50.0μg.L-1以内与其峰面积呈线性关系,方法的检出限(3S/N)为0.052μg.L-1。分析了早、中、晚不同时间的天津市自来水,并用标准加入法做回收试验,测得回收率在97.0%～109.4%之间,测定值的相对标准偏差(n=6)均小于2.5%。     

(2-Ethyl-5-oxo-hexyl) Methylthiomethyl Phthalate as By-product of the Swern Oxidation: Improved Synthesis of Ring-deuterated Major Metabolites of Bis(2-ethylhexyl) Phthalate

Summary. Two ring-deuterated major metabolites of bis(2-ethylhexyl) phthalate were obtained in excellent yields by means of an improved oxidation procedure. The by-product of their interconversion by Swern oxidation is elucidated and a possible mechanism of its formation is proposed.Received February 27, 2003; accepted March 3, 2003 Published online July 28, 2003     

Emulsion liquid membrane extraction of Ni(II) and Co(II) from acidic chloride solutions using bis-(2-ethylhexyl) phosphoric acid as extractant

An emulsion liquid membrane process using bis-(2-ethylhexyl) phosphoric acid (D2EHPA) to extract and separate Ni(II) and Co(II) from acidic chloride solutions is described. Liquid membrane consists of a diluent, a surfactant (Span 80), and an extractant (D2EHPA). Hydrochloric acid was used as the stripping solution. The important parameters governing the permeation of nickel and their effect on the separation process have been studied. These parameters are stirring speed, feed phase pH, surfactant concentration, extractant concentration, stripping phase concentration, phase ratio, initial concentration of metal, and treatment ratio. The optimum conditions have been determined. The separation factors of Ni(II) with respect to Co(II), based on initial feed concentration, have been experimentally determined. Furthermore, the extraction selectivity for Co(II) over Ni(II) has been improved by using D2EHPA during the initial minutes.