基于氧化锌/碳纳米纤维材料的氧氟沙星电化学传感器的构建及应用

通过静电纺丝技术合成碳纳米纤维,以循环伏安法在此碳纤维上电聚合乙酸锌制备复合纳米材料作为一种新型的电化学增敏剂,用于修饰玻碳电极,开发了一种基于碳纤维和氧化锌复合材料的新型电化学传感器(ZnO/CNF/GCE)。使用循环伏安法、差分脉冲伏安法等进行电化学催化性能的研究,并优化实验条件。结果表明,与裸电极相比,在pH 5.5磷酸盐缓冲溶液中,ZnO/CNF/GCE修饰电极能使氧氟沙星的峰电流明显提升,线性范围1~200μmol/L,检测限为0.33μmol/L。该ZnO/CNF/GCE修饰电极已用于氧氟沙星滴耳液中氧氟沙星的含量测定。     

Renewable Surface Sol‐gel Derived Carbon Ceramic Electrode Modified with Copper Complex and Its Application as an Amperometric Sensor for Bromate Detection

A sol‐gel technique was used for the preparation of a three dimensional carbon composite electrode modified with [Cu(bpy)₂]Br₂ complex. A reversible redox couple of Cu(II)/Cu(I) is observed at the electrode surface. The electrochemical behavior and stability of the modified electrode was characterized by cyclic voltammetry. The charge transfer coefficient (α) and charge transfer rate constant (K_s) for the modified electrode were determined by cyclic voltammetry, which were found to be 0.46 and 14.2 s^?1, respectively. The modified electrode showed excellent catalytic activity toward bromate reduction at significantly reduced overpotentials and can be used successfully for amperometric detection of bromate. Under the optimized conditions, the calibration plots are linear in the concentration range 0.5 μM ?200μM. Detection limit (signal to noise is 3) and sensitivity were found to be 0.1 μM and 20 nA / μM, respectively. These analytical parameters compare favorably with those obtained with modern analytical techniques. The modified carbon ceramic electrode doped with Cu‐Complex shows a good reproducibility, a short response time (t<2 s), remarkable long term stability (>4 months) and especially good surface renewability by simple mechanical polishing (RSD for 6 successive polishing is 1.5%).     

Application of carbon nanoparticle/chitosan modified electrode for the square-wave adsorptive anodic striping voltammetric determination of Niclosamide

A new modified electrode formed by carbon nanoparticle/chitosan film (CNP/CS) was used for electrocatalytic reduction of Niclosamide (NA). The electrochemical behavior of NA at the CNP/CS modified electrode was investigated in detail by the means of cyclic voltammetry. The reduction mechanism of NA, corresponds to the redox chemistry of nitro group, was thoroughly investigated. The effect of the experimental parameters e.g. potential and time of accumulation, pH of the buffered solutions and potential sweep rate on the response of the electrode was studied. The prepared electrode showed high stability and uniformity in the composite film, short response time, good reproducibility and an excellent catalytic activity toward the electro-reduction of NA leading to a significant improvement in response sensitivity. The square-wave adsorptive anodic stripping voltammetry (SWAASV) was used as an efficient method for the determination of NA. Under the optimal conditions, the modified electrode showed a wide linear response to the concentration of NA in the range of 0.01–2 μM with a detection limit of 7.7 nM. The prepared electrode was successfully applied for the determination of NA in pharmaceutical and clinical samples and satisfactory results are obtained.     

Copper nanoclusters conjugated silica nanoparticles modified on carbon paste as an electrochemical sensor for the determination of dopamine

An electrochemical sensor based on modification of carbon paste electrode by glutathione‐capped copper nanoclusters silica nanoparticles (CuNCs/SiO₂NPs) composite for determination of dopamine in the presence of ascorbic acid was presented. Transmission electron microscopy, scanning electron microscopy, energy dispersive X‐Ray analysis, X‐ray photoelectron spectroscopy, Fourier‐transform infrared spectroscopy, X‐ray diffraction and electrochemical impedance spectroscopy were used for characterization of the developed electrode. The electrochemical behavior of dopamine on CuNCs/SiO₂NPs/carbon paste electrode was investigated by cyclic voltammetry and differential pulse voltammetry. Dopamine was determined in the range of 10.0 – 900.0 μM, and the limit of detection was obtained as 0.43 μM. The electrochemical behaviors of the coexisting electroactive species, which often cause interference with the determination of dopamine, were investigated. The results show that the developed electrode does not show any interference with respect to coexisting species, even in the presence of ascorbic acid. The developed electrochemical sensor was further employed for the determination of dopamine in human blood plasma, with a good recovery.     

Exploiting multi-function Metal-Organic Framework nanocomposite Ag@Zn-TSA as highly efficient immobilization matrixes for sensitive electrochemical biosensing

A novel multi-function Metal-Organic Framework composite Ag@Zn-TSA (zinc thiosalicylate, Zn(C₇H₄O₂S), Zn-TSA) was synthesized as highly efficient immobilization matrixes of myoglobin (Mb)/glucose oxidase (GOx) for electrochemical biosensing. The electrochemical biosensors based on Ag@Zn-TSA composite and ionic liquid (IL) modified carbon paste electrode (CPE) were fabricated successfully. Furthermore, the properties of the sensors were discussed by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and amperometric current-time curve, respectively. The results showed the proposed biosensors had wide linear response to hydrogen peroxide (H₂O₂) in the range of 0.3–20,000 μM, to nitrite (NO₂⁻) for 1.3 μM–1660 μM and 2262 μM–1,33,000 μM, to glucose for 2.0–1022 μM, with a low detection limit of 0.08 μM for H₂O₂, 0.5 μM for NO₂⁻, 0.8 μM for glucose. The values of the apparent heterogeneous electron transfer rate constant (k_s) for Mb and GOx were estimated as 2.05 s⁻¹ and 2.45 s⁻¹, respectively. Thus, Ag@Zn-TSA was a kind of ideal material as highly efficient immobilization matrixes for sensitive electrochemical biosensing. In addition, this work indicated that MOF nanocomposite had a great potential for constructing wide range of sensing interface.     

Immobilization of nickel-dipicolinic acid onto a glassy carbon electrode modified with bimetallic Au-Pt inorganic-organic hybrid nanocomposite: Application to micromolar detection of fructose

This work describes the electrochemical behavior of nickel-dipicolinic acid (Ni-DPA) film immobilized on the surface of bimetallic Au-Pt inorganic-organic hybrid nanocomposite glassy carbon electrode and its electrocatalytic activity toward the oxidation of fructose. The electrode possesses a three-dimensional (3D) porous network nano architecture, in which the bimetallic Au-Pt serving as metal nano-particle based microelectrode ensembles are distributed in the matrix of interlaced 3,3′,5,5′-tetramethylbenzidine (TMB) organic nanofibers (NFs). The surface structure and composition of the sensor was characterized by scanning electron microscopy (SEM). Electrocatalytic oxidation of fructose on the surface of modified electrode was investigated with cyclic voltammetry and chronoamperometry methods and the results show that the Ni-DPA film displays excellent electrochemical catalytic activities towards fructose oxidation. The hydrodynamic amperometry at rotating modified electrode at constant potential versus reference electrode was used for detection of fructose. Under optimized conditions the calibration plots are linear in the concentration range 0.5 to 70 μM and detection limit was found to be 0.1 μM.     

The NADH Electrochemical Detection Performed at Carbon Nanofibers Modified Glassy Carbon Electrode

In this work, the capability of carbon nanofibers to be used for the design of catalytic electrochemical biosensors is demonstrated. The direct electrochemistry of NADH was studied at a glassy carbon electrode modified using carbon nanofibers. A decrease of the oxidation potential of NADH by more than 300 mV is observed in the case of the assembled carbon nanofiber‐glassy carbon electrode comparing with a bare glassy carbon electrode. The carbon nanofiber‐modified electrode exhibited a wide linear response range of 3×10^?5 to 2.1×10^?3 mol L^?1 with a correlation coefficient of 0.997 for the detection of NADH, a high specific sensitivity of 3637.65 (μA/M cm²), a low detection of limit (LOD=3σ) of 11 μM, and a fast response time (3 s). These results have confirmed the fact that the carbon nanofibers represent a promising material to assemble electrochemical sensors and biosensors.     

Layer-by-layer sensor architecture of polymers and nanoparticles for electrochemical detection of uric acid in human urine samples

Excessive uric acid levels in the human body (hyperuricemia) are the main causes of kidney stones and diabetes. In this study, a layer-by-layer arrangement of polymers and nanocomposites is used as a new electrode sensing material for rapid and direct electrochemical determination of uric acid (UA). The electrode surface architecture was constructed by the incorporation of poly (amidoamine) dendrimer with 0.5 generation (poly (amidoamine) [PAMAM] [D-G0.5]) of multiwalled carbon nanotube-silver nanoparticles (MWCNT-AgNP) and a poly (neutral-red) (poly [NR]) polymer. The PAMAM (D-G0.5)/MWCNT-AgNP/poly (NR)-coated electrode has a good electrocatalytic activity for the determination of UA using cyclic voltammetry and showed remarkable enhancement in current response at a low-oxidation potential (0.3 V). Under optimal conditions, the developed electrochemical sensor showed an excellent and wide linear range for the determination of UA (i.e. 0.016 μM–2500 μM), and the limit of detection was found to be 0.005 μM. The modified sensor system demonstrated excellent sensitivity and selectivity toward the detection of UA in the presence of interfering substances, which are commonly found in urine and human fluid samples. Furthermore, the developed sensor has represented both reproducibility and excellent stability for the UA determination in real samples (human urine).     

The Cu-MOF-199/single-walled carbon nanotubes modified electrode for simultaneous determination of hydroquinone and catechol with extended linear ranges and lower detection limits

A novel electrochemical sensor based on Cu-MOF-199 [Cu-MOF-199 = Cu₃(BTC)₂ (BTC = 1,3,5-benzenetricarboxylicacid)] and SWCNTs (single-walled carbon nanotubes) was fabricated for the simultaneous determination of hydroquinone (HQ) and catechol (CT). The modification procedure was carried out through casting SWCNTs on the bare glassy carbon electrode (GCE) and followed by the electrodeposition of Cu-MOF-199 on the SWCNTs modified electrode. Cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and scanning electron microscopy (SEM) were performed to characterize the electrochemical performance and surface characteristics of the as-prepared sensor. The composite electrode exhibited an excellent electrocatalytic activity with increased electrochemical signals towards the oxidation of HQ and CT, owing to the synergistic effect of SWCNTs and Cu-MOF-199. Under the optimized condition, the linear response range were from 0.1 to 1453 μmol L⁻¹ (R_HQ = 0.9999) for HQ and 0.1–1150 μmol L⁻¹ (R_CT = 0.9990) for CT. The detection limits for HQ and CT were as low as 0.08 and 0.1 μmol L⁻¹, respectively. Moreover, the modified electrode presented the good reproducibility and the excellent anti-interference performance. The analytical performance of the developed sensor for the simultaneous detection of HQ and CT had been evaluated in practical samples with satisfying results.     

Electrochemical preparation of composite of poly brilliant cresyl blue (PBCB)–poly 5-amino-2-napthalenesulfonic acid electrode and electrocatalytic application

Poly brilliant cresyl blue (PBCB) and poly 5-amino-2-napthalenesulfonic (PANS) polymer composite modified electrode was fabricated by the electrochemical polymerization of brilliant cresyl blue and 5-amino-2-napthalenesulfonic acid. When compared polymer composite electrodes with PBCB and PANS electrode, it showed enhanced electrochemical property. The morphology of the resulting composite electrode was characterized by AFM, and the electrochemical properties of the modified electrode were characterized by cyclic voltammetry and amperometry. The composite electrode showed surface-confined and pH-dependent electrochemical property. The composite electrode exhibited high catalytic behavior toward the reduction of hydrogen peroxide at low overpotential. The detection limit and sensitivity of the electrode toward H₂O₂ detection was 5 μM and 1 μA/mM, respectively, and response time was less than 10 s for hydrogen peroxide.     

Preparation and characterization of Ni(II)/polyacrylonitrile and carbon nanotube composite modified electrode and application for carbohydrates electrocatalytic oxidation

A nickel(II) into porous polyacrylonitrile–carbon nanotubes composite modified glassy carbon electrode (Ni/PAN-CNT/GCE) was fabricated by simple drop-casting and immersing technique. The unique electrochemical activity of Ni/PAN-CNT composite modified glassy carbon electrode was illustrated in 0.10?M NaOH using cyclic voltammetry. The Ni/PAN-CNT/GCE exhibits the characteristic of improved reversibility and enhanced current responses of the Ni(III)/Ni(II) couple compared with Ni/PAN/GCE and Ni/CNT/GCE. The results of electrochemical impedance spectroscopy and scanning electron microscopy indicated the successful immobilization for PAN-CNT composite film. Kinetic parameters such as the electron transfer coefficient, α, and rate constant, k _s, of the electrode reaction were determined. Ni/PAN-CNT/GCE also shows good electrocatalytic activity toward the oxidation of carbohydrates (glucose, sucrose, fructose, and sorbitol). The electrocatalytic response showed a wide linear range (10–1,500, 12–3,200, 7–3,500, and 16–4,200?μM for glucose, sucrose, fructose, and sorbitol, respectively) as well as its experimental limit of detection can be achieved 6, 7, 5, and 11?μM for glucose, sucrose, fructose, and sorbitol, respectively. The modified electrode for carbohydrates determination is of the property of simple preparation, good stability, and high sensitivity.     

Immobilization of Ni–Pd/core–shell nanoparticles through thermal polymerization of acrylamide on glassy carbon electrode for highly stable and sensitive glutamate detection

The preparation of a persistently stable and sensitive biosensor is highly important for practical applications. To improve the stability and sensitivity of glutamate sensors, an electrode modified with glutamate dehydrogenase (GDH)/Ni–Pd/core–shell nanoparticles was developed using the thermal polymerization of acrylamide (AM) to immobilize the synthesized Ni–Pd/core–shell nanoparticles onto a glassy carbon electrode (GCE). The modified electrode was characterized by scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy, cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS). Electrochemical data showed that the prepared biosensor had remarkably enhanced electrocatalytic activity toward glutamate. Moreover, superior reproducibility and excellent stability were observed (relative average deviation was 2.96% after continuous use of the same sensor for 60 times, and current responses remained at 94.85% of the initial value after 60 d). The sensor also demonstrated highly sensitive amperometric detection of glutamate with a low limit of detection (0.052 μM, S/N = 3), high sensitivity (4.768 μA μM⁻¹ cm⁻²), and a wide, useful linear range (0.1–500 μM). No interference from potential interfering species such as l-cysteine, ascorbic acid, and l-aspartate were noted. The determination of glutamate levels in actual samples achieved good recovery percentages.     

Electrochemical determination of L-Tryptophan, L-Tyrosine and L-Cysteine using electrospun carbon nanofibers modified electrode

A novel and simple method for the direct and quantitative determination of L-tryptophan (Trp), L-tyrosine (Tyr) and L-cysteine (Cys) was proposed in this work. Carbon nanofibers (CNFs), made by electrospinning technique, were used to modify carbon paste electrode (CPE) without any treatment to study the electrochemical behaviors of the three amino acids using cyclic voltammetry (CV) and constant potential amperometric method. The results demonstrated that the CNFs modified carbon paste electrode (CNF-CPE) exhibited high electrocatalytic activity and good analytical performance towards the oxidation of the three amino acids. The linear ranges of Trp, Tyr and Cys were 0.1-119, 0.2-107 and 0.15-64 μM with correlation coefficients of 0.9994, 0.9985 and 0.9996, respectively. All the detection limits of the analytes were 0.1 μM (S/N = 3). In addition, the CNF-CPE displayed good reproducibility, high sensitivity and good selectivity towards the determination of the amino acids, making it suitable for the determination of Trp, Tyr and Cys in clinical and medicine.     

Room-Temperature Ionic Liquid and Multi-Walled Carbon Nanotube Composite Modified Carbon-Ceramic Electrode as a Sensitive Voltammetric Sensor for Indomethacin

The electrochemical behavior of indomethacin on the surface of a carbon-ceramic electrode modified with multi-walled carbon nanotubes and an ionic liquid composite film is reported. The results show that the nano-structured film exhibited excellent enhancement effects on the electrochemical oxidation of indomethacin. The developed sensor presented a linear response to indomethacin over the concentration range from 1 to 50 µM with a detection limit of 0.26 µM. The proposed modified electrode was employed for the determination of indomethacin in biological and pharmaceutical samples using differential pulse voltammetry.     

Highly sensitive electrochemical determination of Sunset Yellow based on gold nanoparticles/graphene electrode

An electrochemical sensor was prepared using Au nanoparticles and reduced graphene successfully decorated on the glassy carbon electrode (Au/RGO/GCE) through an electrochemical method which was applied to detect Sunset Yellow (SY). The as-prepared electrode was characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), atomic force microscopy (AFM) and electrochemical measurements. The results of cyclic voltammetry (CV) proved that Au/RGO/GCE had the highest catalytic activity for the oxidation of SY as compared with GCE, Au/GCE, and RGO/GCE. Differential pulse voltammetry (DPV) showed that the linear calibration curves for SY on Au/RGO/GCE in the range of 0.002 μM–109.14 μM, and the detection limit was estimated to be 2 nM (S/N = 3). These results suggested that the obtained Au/RGO/GCE was applied to detect SY with high sensitivity, low detection limit and good stability, which provided a promising future for the development of portable sensor in food additives.     

A selective determination of norepinephrine on the glassy carbon electrode modified with poly(ethylenedioxypyrrole dicarboxylic acid) nanofibers

A glassy carbon electrode modified with poly(3,4-ethylenedioxypyrrole-2,5-dicarboxylic acid) nanofibers (PEDOPA-NFs) was prepared for the determination of norepinephrine (NE) in phosphate buffer saline. The modified electrode demonstrated an improved sensitivity and selectivity toward the electrochemical detection of NE and could detect separately ascorbic acid (AA), uric acid (UA), and NE in their mixture. The separations of the oxidation peak potentials of NE–AA and NE–UA were 160 and 150 mV, respectively. Meanwhile, the modified electrode showed higher sensitivity and selectivity toward NE than dopamine and epinephrine. Using differential pulse voltammetry, the oxidation peak current of NE was found to be linearly dependent on its concentration within the range of 0.3–10 μM, and the detection limit of the NE oxidation current was 0.05 μM at a signal-to-noise ratio of 3. The PEDOPA-NFs promoted the electron transfer reaction of NE, while the PEDOPA-NFs, acting as a negatively charged linker, combined with the positively charged NE to induce NE accumulation in the NFs at pH under 7.4. However, the PEDOPA-NFs restrained the electrochemical response of the negatively charged AA and UA due to the electrostatic repulsion. The result indicates that the modified electrode can be used to determine NE without interference from AA and UA and selectively in the mixture of catecholamines.     

Synthesis and Electrochemical Investigation of Tetra Amino Cobalt (II) Phthalocyanine Functionalized Polyaniline Nanofiber for the Selective Detection of Dopamine

A new electrochemical sensing platform based on tetra‐amino cobalt (II) phthalocyanine (TACoPc) ingrained polyaniline (PANI) nanofiber composite (TACoPc/PANI hybrid) has been developed for the selective detection of dopamine. The uniform fibrous network of PANI/TACoPc hybrid was synthesized by a one‐step oxidative polymerization at room temperature. The synthesized nanocomposite was characterized using field emission scanning electron microscopy (FESEM), energy dispersive X‐ray (EDX), fourier transmission infrared spectroscopy (FTIR), raman spectroscopy, X‐ray diffraction (XRD) and UV‐Visible spectroscopy. The electrochemical behavior of the TACoPc/PANI hybrid material was studied by using different electrochemical techniques, including cyclic voltammetry (CV) and chronoamperometry in 0.1 M phosphate buffer solution (PBS) of pH 7 by modifying the glassy carbon electrode (GCE). Due to the synergistic impact of PANI and TACoPc, the suggested altered electrode provided superior catalytic performance for dopamine even in the presence of ascorbic acid. It exhibited a linear reaction with a high sensitivity of 1.212 μA/μM cm^?2 and a low detection limit of 0.064 μM over the 20–200 μM concentration range in 0.1 M PBS. One of the commonly faced problems of interference of ascorbic acid and uric acid in the electrochemical detection of dopamine was completely excluded from this modified electrode which led to an increase in the catalytic activity of the material for the detection of dopamine in the presence of ascorbic acid.     

Electrochemical Characterization of Polymerized Cresol Red Film Modified Glassy Carbon Electrode and Separation of Electrocatalytic Responses for Ascorbic Acid and Dopamine Oxidation

A cresol red modified glassy carbon electrode was prepared using an electrochemical method. The cyclic voltammograms of the modified electrode indicate the presence of a couple of well-defined redox peaks, and the formal potential shifts in the negative direction with increasing solution pH. The modified electrode exhibits high electrocatalytic activity toward ascorbic acid oxidation, with an overpotential of 300 mV less than that of bare glassy carbon electrodes, and drastic enhancement of the anodic currents. The calibration graph obtained by linear sweep voltammetry for ascorbic acid is linear in the range of 50∼500 µM. The electrode markedly enhances the current response of dopamine and can separate the electrochemical responses of ascorbic acid and dopamine. The separation between the anodic peak potentials of ascorbic acid and dopamine is 190 mV by cyclic voltammetry. The linear sweep voltammetric peak currents for dopamine in the presence of 2 mM ascorbic acid vary linearly with a concentration of between 10 and 100 µM.     

Electrochemical determination of naproxen in the presence of acetaminophen using a carbon paste electrode modified with activated carbon nanoparticles

In this study, cyclic voltammetry and differential pulse voltammetry were used to determine the electrochemical properties and concentration of naproxen in pharmaceutical formulation and human serum samples by using a carbon paste electrode modified with activated carbon nanoparticles. Optimum conditions were obtained at an electrode with 0.005 g activated carbon nanoparticles in a phosphate buffer solution of pH 6 as a supporting electrolyte. Linear calibration curves were obtained in the range of 0.1–120 μM, and the detection limit of naproxen determined was 0.0234 μM. The modified electrode shows good selectivity for naproxen in the presence of some organic and inorganic interferences and very good precision in real samples. Finally, naproxen was measured in the presence of acetaminophen.     

Gold nanoparticles-carbon nanotubes modified sensor for electrochemical determination of organophosphate pesticides

An electrochemical sensor was developed for the detection of organophosphate pesticides based on electrodeposition of gold nanoparticles on a multi-walled carbon nanotubes modified glassy carbon electrode. Cyclic voltammetry was employed in the process of electrodeposition. Field emission scanning electron microscope and X-ray diffraction techniques were used for characterization of the composite. Organophosphate pesticides (e.g. parathion) were determined using linear scan voltammetry. A highly linear response to parathion in the concentration range from 6.0?×?10^?5 to 5.0?×?10^?7 M was observed, with a detection limit of 1.0?×?10^?7 M estimated at a signal-to-noise ratio of 3. The method has been applied to the analysis of parathion in real samples.