Enhanced separation of seven quinolones by capillary electrophoresis with silica nanoparticles as additive

This paper describes the enhanced separation of lomefloxacin, sparfloxacin, fleroxacin, norfloxacin, ofloxacin, gatifloxacin and pazufloxacin by capillary zone electrophoresis (CZE) using silica nanoparticles (SiNPs) as running buffer additive. The impact of SiNPs concentration on the resolution and selectivity of separation was investigated and a given value of SiNPs was finally chosen under the optimum conditions. The addition of the SiNPs to the running buffer enabled electroosmotic flow (EOF) decrease and permitted full interaction between SiNPs and analytes. The influence of separation voltage, pH and buffer concentration on the separation in the presence of SiNPs was examined. Interactions between drugs and nanoparticles during the separation are discussed; the determination of interaction constants is also achieved. A good resolution of seven quinolones was obtained within 15 min in a 50 cm effective length fused-silica capillary at a separation voltage of +10 kV in a 12 mM disodium tetraborate-phosphate buffer (pH 9.08) containing 5.2 μg mL⁻¹ SiNPs.     

Size separation of silica nanospheres by means of capillary zone electrophoresis

The electrophoretic mobility of silica nanospheres was shown to be a function of separation conditions such as pH and phosphate concentration of a carrier electrolyte. The separation selectivity can be controlled by the separation conditions and optimised depending on the sample composition. The effects of pH and phosphate concentration of buffer solutions on the nanosphere electrophoretic mobility are explained using the Overbeek-Booth electrokinetic theory taking into account both electrophoretic retardation and the relaxation effect.     

高效液相色谱法测定烟草料液中的糖

研究了用蒸发光散射检测器检测，高效液相色谱法测定烟草料液中糖的方法。料液中的糖用固相萃取预分离，然后以Waters carbohydrate高效糖柱为固定相，V（乙腈）：V（水）=70：30作为流动相分离，蒸发光散射检测器检测；样品中鼠李糖、木糖、阿拉伯糖、果糖、甘露糖、葡萄糖、蔗糖、麦芽糖8种糖的加标回收率分别为：97．0％、95．6％、102％、102．1％、95．0％、101．8％、102．6％、97．8％；线性范围分别为：鼠李糖、果糖、葡萄糖、蔗糖0．1～20pg，木糖、阿拉伯糖、甘露糖、麦芽糖0．2～25μg。相对标准偏差均小于3．2％。方法的检出限达：鼠李糖20ng、木糖26ng、阿拉伯糖28ng、果糖14ng、甘露糖20ng、葡萄糖10ng、蔗糖12ng、麦芽糖15ng，用该方法测定了烟草料液中的糖。     

Linearization of evaporative light scattering detector signal

Recent advances in nebulizer technology of the evaporative light scattering detector (ELSD) allow the evaporation of trichlorobenzene (TCB) at much lower temperatures than the previous instruments, thus avoiding the sample loss in the lower molecular weight domain. Therefore, the new ELSD opens the possibility to correctly evaluate the molecular weight distribution (MWD) of polymers by gel permeation chromatography, after linearizing the ELSD signal intensity in function of concentration. To find the correct exponent parameter for linearization, it is necessary to take into account not only the peak area, but each point of the chromatogram. The evaluation method for this exponent parameter, found to be 1.61 for the analysis in TCB of polyolefin and polystyrene samples, is presented in this study. This value was verified by the excellent correlation found between the obtained MWD of a high-density polyethylene both with the ELSD and with the traditional differential refractive index detector.     

Amphiphilic silica nanoparticles as pseudostationary phase for capillary electrophoresis separation

Amphiphilic silica nanoparticles surface-functionalized by 3-aminopropyltriethoxysilane (APTES) and octyltriethoxylsilane (OTES) were successfully prepared and characterized using scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier transform infrared spectrometry (FT-IR) and thermogravimetry (TG) techniques. The potential use of these bifunctionalized nanoparticles as pseudostationary phases (PSPs) in capillary electrophoresis (CE) for the separation of charged and neutral compounds was evaluated in terms of their suitability. As expected, fast separation of representative aromatic acids was fulfilled with high separation efficiency, because they migrate in the same direction with the electroosmotic flow (EOF) under optimum experimental conditions. Using a buffer solution of 30mmol/L phosphate (pH 3.0) in the presence of 0.5mg/mL of the synthesized bifunctionalized nanoparticles, the investigated basic compounds were baseline-resolved with symmetrical peaks. Due to the existence of amino groups on the surface of nanoparticles, "silanol effect" that occurs between positively charged basic analytes and the silanols on the inner surface of capillary was greatly suppressed. Furthermore, the separation systems also exhibited reversed-phase (RP) behavior when neutral analytes were tested.     

Studying the size/shape separation and optical properties of silver nanoparticles by capillary electrophoresis

This paper describes the feasibility of employing capillary electrophoresis (CE) to separate silver particles in nanometer regimes. We have found that the addition of an anionic surfactant, sodium dodecyl sulphate (SDS), to the running electrolyte prevents coalescence of the silver particles during the process, which improves the separation performance; the concentration of SDS required for optimal silver nanoparticle separation is ca. 20 mM. By monitoring the electropherograms using a diode-array detection (DAD) system, we have also investigated the separation of suspended silver nanorods with respect to their shapes. Our results demonstrate that the combination of CE and DAD is a powerful one for the separation and characterization of various silver nanoparticles.     

A new method for the determination of biogenic amines in cheese by LC with evaporative light scattering detector

This paper presents a new LC method with evaporative light scattering detection (ELSD), for the separation and determination of the biogenic amines (histamine, spermidine, spermine, tyramine, putrescine and β-phenylethylamine) which are commonly present in cheese, as their presence and relative amounts give useful information about freshness, level of maturing, quality of storage and cheese authentication. The LC-ELSD method is validated by comparison of the results with those obtained through LC-UV determination, based on a pre-column dansyl chloride derivatisation step. The obtained data demonstrate that both methods can be interchangeably used for biogenic amines determination in cheese. The new LC-ELSD method shows good precision and permits to achieve, for standard solutions, limit of detection (LOD) values ranging from 1.4 to 3.6 mg L⁻¹ and limit of quantitation (LOQ) values ranging from 3.6 to 9.3 mg L⁻¹. The whole methodology, comprehensive of the homogenization-extraction process and LC-ELSD analysis, has been applied in the analysis of a typical Calabria (Southern Italy) POD cheese, known as Caciocavallo Silano. The most aboundant amine found was histamine, followed, in decreasing order, by tyramine, spermine, putrescine, β-phenylethylamine and spermidine, for a total amount of 127 mg kg⁻¹. This value does not represent a possible risk for consumer health, according to the toxicity levels reported in literature and regarded as acceptable.     

微流蒸发光散射检测器与毛细管液相色谱的联用及其在银杏叶提取物分析中的应用

将微流蒸发光散射检测器( μELSD)与毛细管液相色谱(cLC)联用,应用于中药银杏叶提取物及其分散片制剂的分离检测领域。首先对 μELSD仪器参数进行优化。通过调节漂移管温度与载气流量,提高了分析物的响应,并减小了噪声。然后,搭建了cLC-μELSD分离检测平台,其相对常规LC可大大减小实验试剂消耗。流动相A为0.05%(体积分数,下同)三氟乙酸(TFA)水溶液,流动相B为含0.05% TFA的甲醇溶液。最优的洗脱梯度条件为:0~10 min,5%B~25%B;10~25 min,25%B~38%B;25~35 min,38%B;35~40 min,38%B~42%B;40~55 min,42%B~50%B。银杏叶提取物和复杂中药制剂银杏叶提取物分散片都得到了较好的分离,并在其中鉴定到紫外波段几乎无吸收的重要内酯类活性成分白果内酯以及银杏内酯A、B和C。测定了不同厂家银杏叶提取物中萜类内酯洗脱时间的相对标准偏差,结果均不大于2.42%,表明该体系在目标物的分析上具有良好的重现性。实验证明所建立的cLC-ELSD体系在复杂中药体系的分离检测中有良好的应用性。     

New evaporative light scattering detector for high temperature gel permeation chromatography

A new evaporative light scattering detector (ELSD) for the analysis of polyolefins by high temperature gel permeation chromatography (GPC) was recently introduced by Agilent Technologies. For the first time, we investigated the possibility to use this detector to measure the molecular weight distributions (MWD) of different type of polyolefines (polypropylene, linear, and low-density polyethylene). These samples were previously characterized by GPC with a differential refractive index (DRI) detector by several companies, in an interlaboratory study conducted by International Union of Pure and Applied Chemistry.^[1 Luruli, N. 2010. PHASE 1: IUPAC SEC/GPC Round Robin Project Report: Repeatability and Reproducibility of Sample Preparation and Analysis in High-Temperature SEC, http://media.iupac.org/projects/2005/2005-011-3-400_rpt-phase1_110510.pdf [Google Scholar]^] The excellent baseline stability of ELSD as compared with DRI was reflected in a better reproducibility of the measured average molecular weights. More importantly, after applying required corrections to linearize the response of the ELSD as a function of concentration, we obtained similar results as previously obtained with DRI for the MWD of analyzed resins, covering typical applications of polyolefins.     

Determination of methylene blue by resonance light scattering method using silica nanoparticles as probe

A simple and novel method was developed to determine methylene blue(MB) by resonance light scattering(RLS) using silica nanoparticles(SiO_2NPs) as the probe.It was found that MB could enhance the RLS intensity of SiO_2NPs.Moreover,the increase in RLS intensity was linear with the concentration of MB over the range of 0.01-3.0 μg mL~(-1).The limit of detection(LOD) was as low as 4.36 ng mL~(-1)(3σ) and the relative standard deviation(RSD) was 2.4%(n=6).Under the optimum experimental conditions,this proposed method was successfully applied for the determination of MB in aquaculture samples with recoveries between 96.3% and 107%.Possible mechanisms for the RLS enhancement of SiO_2NPs in the presence of MB were also discussed.     

The application of functional silica nanoparticles to fulfill the rapid and improved enantioselective capillary electrophoresis separation of amino acid derivatives

In this study, diamino moiety functionalized silica nanoparticles with the size of 118 ± 12 nm were successfully synthesized and directly introduced into a chiral capillary electrophoresis system to improve the enantioseparation of 9‐fluorenyl methoxycarbonyl derivatized amino acids using norvancomycin as chiral selector. Under acidic background electrolyte conditions, functional silica nanoparticles can be readily adsorbed onto the inner surface of bare silica capillary column through electrostatic interaction to form a dynamic coating, resulting in a reversed anodic electro‐osmotic flow (i.e. from cathode to anode). As expected, chiral amino acid derivatives (usually negatively charged) can be rapidly separated under co‐electro‐osmotic flow conditions in the current separation system. Furthermore, the column performance and detection sensitivity for the enantioseparation were also obviously improved because the adsorption of chiral selector of norvancomycin to the capillary wall was greatly suppressed. Some important factors influencing the separation, such as the coating thickness, background electrolyte concentration, functional silica nanoparticles concentration, and the organic modifier were also investigated and the optimized separation conditions were obtained.     

Investigation of iron oxide nanoparticles by capillary zone electrophoresis

The electrophoretic behavior of γ-Fe₂O₃ nanoparticles was studied in aqueous solutions of Na₂SO₄-NaOH (pH 10.8) and of Na₂SO₄-Na₃cit (pH 7.1) as running electrolytes. Two electrophoretic zones (smooth and with spikes) due to colloidal and suspended particles of approximately the same size range were formed during the runs. The suspension stability and size distribution were shown to depend on the composition of electrolyte used for dispersing the solids. The effects of electric field strength, injection time, injection pressure as well as sodium citrate concentration were studied and particle electrophoretic mobilities were calculated. Electron micrographs of particles studied were obtained. Preparation of reference samples based on the colloidal γ-Fe₂O₃ has been discussed.     

Use of polystyrene nanoparticles to enhance enantiomeric separation of propranolol by capillary electrophoresis with Hp-beta-CD as chiral selector

We describe the use of polystyrene (PS) nanoparticles to manipulate chiral selectivity of propranolol analysis by capillary electrophoresis, by dispersing PS nanoparticles into the run buffer employing hydroxypropyl-β-cyclodextrin (HP-β-CD) as chiral selector. Distinct separational differences are observed between the buffer containing PS nanoparticles and buffer without, when changing separating conditions including PS nanoparticles concentration, pH, buffer concentration, HP-β-CD concentration and when adding an organic additive. Selectivity improvements are reflected by changes in the observed mobility as a result of interactions between the propranolol enantiomers and HP-β-CD governing the absorption process on the PS particles surface. The presence of PS nanoparticles increases the enantioseparation at low particle concentration in the presence of HP-β-CD as a chiral selector.     

Silica nanoparticles for separation of biologically active amines by capillary electrophoresis with laser-induced native fluorescence detection

This paper describes the analysis of biologically active amines by capillary electrophoresis (CE) in conjunction with laser-induced native fluorescence detection. In order to simultaneously analyze amines and acids as well as to achieve high sensitivity, 10 mM formic acid solutions (pH < 4.0) containing silica nanoparticles (SiNPs) were chosen as the background electrolytes. With increasing SiNP concentration, the migration times for seven analytes decrease as a result of increase in electroosmotic flow (EOF) and decrease in their electrophoretic mobilities against EOF. A small EOF generated at pH 3.0 reveals adsorption of SiNPs on the deactivated capillary wall. The decreases in electrophoretic mobilities with increasing SiNP concentration up to 0.3x indicate the interactions between the analytes and the SiNPs. Having a great sensitivity (the limits of detection at a signal-to-noise ratio (S/N) = 3 of 0.09 nM for tryptamine (TA)), high efficiency, and excellent reproducibility (less than 2.4% of the migration times), this developed method has been applied to the analysis of urinal samples with the concentrations of 0.50 +/- 0.02 microM, 0.49 +/- 0.04 microM, and 74 +/- 2 microM for TA, 5-hydroxytryptamine, and tryptophan, respectively. The successful examples demonstrated in this study open up a possibility of using functional nanoparticles for the separation of different analytes by CE.     

Isolation of ceramide fractions from skin sample by subcritical chromatography with packed silica and evaporative light scattering detection

Separative method of lipid classes from the stratum corneum was developed with packed silica and supercritical CO2 containing 10% of methanol at 15 degrees C, 15 MPa and 3 ml min(-1). The elution order of lipid classes was first esterified cholesterol, triglycerides, squalene co-eluted in a single peak, then free fatty acids, free cholesterol, ceramides and finally glycosylceramides. The ceramides were eluted in several fractions which depended on the number of hydroxyl groups in the molecule, i.e. more hydroxyl groups were contained in ceramides, more important was the retention. Moreover, the retention was not altered by the presence of carbon double bond and variation of the alkyl chain length. The ceramide response with the evaporative light scattering detector was improved by turning the influence of the solvent nature on the response to advantage. Therefore, addition of various solvents with or without triethylamine and formic acid were tested in post-column due to the incompatibility of such modifiers with silica stationary phase. Thereby the solvent conditions for the separation and the detection can be adjusted almost independently. The response was greatly increased by post-column addition of 1% (v/v) triethylamine and its equivalent amount of formic acid in dichloromethane introduced at 0.1 ml min(-1) into the mobile phase. This device had allowed the detection of 400 ng of ceramide with a S/N = 21, whereas no peak was observed in absence of the post-column addition. Finally, the method was applied to the treatment of skin sample which led to highly enriched ceramide fraction.     

A new high-performance liquid chromatographic method with evaporative light scattering detector for the analysis of phospholipids. Application to Iberian pig subcutaneous fat

A new method for the analysis of phospholipids by normal-phase HPLC is described using a silica column. Addition of ammonia and triethylamine to a gradient based on chloroform/methanol/water promoted a good and rapid separation of phospholipid classes (20 min run). The use of an evaporative light scattering detector permitted an accurate analysis of a mixture of phospholipids. Calibration curves were linear within different range for each phospholipid class. The LOD and LOQ obtained were below 0.03 and 0.05 mg kg⁻¹ for all cases, respectively. Besides, a new method for the separation of phospholipids from total lipids before HPLC analysis by a solid-phase extraction (SPE) with Si cartridges has been developed. This methodology gave a good recovery ranging from 97 to 117%. The method was validated with a standard mixture of phospholipids. This method has been applied to characterize the phospholipid fraction of subcutaneous fat from Iberian pig. Cardiolipin, phosphatidylethanolamine, phosphatidylinositol, phosphatidylserine, phosphatidylcholine, and sphingomyelin have been described for first time in these samples. The fatty acid composition of the different phospholipid classes and their HPLC electrospray ionization mass spectrometry have been used for characterizing the molecular species present in each one.     

Polyolefin characterization in dibutoxymethane by high temperature gel permeation chromatography with a new evaporative light scattering detector

A new evaporative light scattering detector (ELSD) for the analysis of polyolefins by high temperature gel permeation chromatography (GPC) was recently introduced by Agilent Technologies. For the first time, we investigated the possibility to use this detector to measure the molecular weight distributions (MWD) of different types of polyolefins (polypropylene, linear and low-density polyethylene) in dibutoxymethane (DBM, butylal). These samples were previously characterized by GPC in trichlorobenzene (TCB) with a differential refractive index (DRI) detector in an interlaboratory study conducted by the International Union of Pure and Applied Chemistry (IUPAC) [1], and in a recent publication by GPC with the new ELSD in TCB [2]. The signal to noise of ELSD using DBM is about 10 times lower than that for TCB. However, the ELSD signal power exponent for DBM was measured as 1.35, which is much closer to unity than the value of 1.61 for TCB. After applying the required corrections to linearize the response of the ELSD signal as a function of concentration, similar average molecular weights to those measured in the interlaboratory study using DRI, were obtained for the analyzed resins.     

Fast and direct quantification of underivatized muscone by ultra performance liquid chromatography coupled with evaporative light scattering detection

A new reversed phase ultra performance liquid chromatography coupled with evaporative light scattering detection is developed for the fast and direct quantification of underivatized muscone in precious herbal medicine musk. Separation of muscone was achieved on a Waters Acquity BEH C₁₈ (50 × 2.1 mm id, 1.7 μm) column. The runtime was as short as 5 min. The mode of evaporative light scattering detection was set at Impact On. The influence of evaporative light scattering detection condition on sensitivity was investigated. The optimized condition was: drift tube temperature at 30°C, gas flow rate 4.2 L/min. The method was validated with respect to the precision, sensitivity, accuracy, linearity, stability, and robustness were measured in this paper. The calibration curves showed good linear regression (r = 0.9914) within the test range. The recovery rate was 98.6%. The limit of detection for muscone was 2.0 ng. The validated method was rapid, simple, reproducible, and convenient for the quantification of muscone in musk and the related products.     

Preparative separation of dioscin derivatives from Dioscorea villosa by centrifugal partition chromatography coupled with evaporative light scattering detection

Dioscin derivatives from the Dioscorea villosa roots were isolated and purified by centrifugal partition chromatography coupled with evaporative light scattering detection. The two-phase solvent system composed of chloroform-methanol-isopropanol-water (7:6:1:4, v/v/v/v) was used to obtain prosapogenin A of dioscin (1, 11.1 mg), dioscin (2, 8.9 mg), deltonin (3, 29.2 mg) and diosgenin 3-O-[alpha-L-rhamnopyranosyl(1 --> 2)]-[beta-D-glucopyranosyl(1 --> 3)-beta-D-glucopyranosyl(1 --> 4)]-beta-D-glucopyranoside (4, 6.2 mg) from 300 mg of saponin-rich extract from the roots of D. villosa. The purities of 1, 2, 3 and 4 were determined to be 98.9, 97.4, 99.2 and 99.5%, respectively. Their chemical structures were determined by spectroscopic data of ESI-MS, 1H NMR and 13C NMR and comparing with those of previously reported values.     

Use of evaporative light scattering detection for the quality control of drug substances: Influence of different liquid chromatographic and evaporative light scattering detector parameters on the appearance of spike peaks

High performance liquid chromatography (HPLC) with evaporative light scattering detection (ELSD) is a versatile, easy to use and inexpensive alternative when it comes to the analysis of substances lacking a chromophor for UV detection. However, in pharmaceutical analysis injection of highly concentrated test solutions are normally required to control impurities at low levels. Under these conditions spike peaks were observed in the chromatograms of the test solutions making a proper evaluation of the impurity profile impossible. The influence of different eluent and ELSD parameters such as eluent composition, eluent flow-rate, ELSD scavenger gas flow-rate and evaporation temperature on the appearance of spike peaks was investigated. It could be shown that spike peaks can be avoided when selecting elevated eluent flow-rates and ESLD scavenger gas flow-rates. Moreover, eluents containing high amounts of organic modifier seem to foster the appearance of spike peaks.