Influence of surface contaminations on the hydrogen storage behaviour of metal hydride alloys

Hydrogen storage in metal hydrides is a promising alternative to common storage methods. The surface of a metal hydride plays an important part in the absorption of hydrogen, since important partial reaction steps take place here. The development of surface contaminations and their influence on hydrogen absorption is examined by means of absorption experiments and surface analysis, using X-ray photoelectron spectroscopy (XPS), thermal desorption mass spectrometry (TDMS) and secondary neutral mass spectrometry (SNMS), in this work. All investigations were carried out on a modern AB₂ metal hydride alloy, namely Ti_0.96Zr_0.04Mn_1.43V_0.45Fe_0.08. Surface analysis (SNMS, XPS) shows that long-term air storage (several months) leads to oxide layers about 15 nm thick, with complete oxidation of all main alloy components. By means of in situ oxygen exposure at room temperature and XPS analysis, it can be shown that an oxygen dose of about 100 Langmuirs produces an oxide layer comparable to that after air storage. Manganese enrichment (segregation) is also clearly observed and is theoretically described here. This oxide layer hinders hydrogen absorption, so an activation procedure is necessary in order to use the full capacity of the metal hydride. This procedure consists of heating (T = 120° C) in vacuum and hydrogen flushing at pressures like p = 18 bar. During the activation process the alloy is pulverized to particles of ∼20 μm through lattice stretches. It is shown that this pulverization of the metal hydride (creating clean surface) during hydrogen flushing is essential for complete activation of the material. Re-activation of powder contaminated by small doses of air (p ≈ 0.1 bar) does not lead to full absorption capacity. In ultrahigh vacuum, hydrogen is only taken up by the alloy after sputtering of the surface (which is done in order to remove oxide layers from it), thus creating adsorption sites for the hydrogen. This is shown by TDMS measurements with and without sputtering and oxygen exposure. Figure Investigated metal hydride before and after activation     

Atomic deuterium (hydrogen) adsorption on thin silver films

Atomic deuterium and hydrogen adsorption on thin silver films deposited under UHV conditions on Pyrex glass was studied by means of measurements of the resistance changes ΔR combined with thermal desorption mass spectrometry (TDMS). The roughness factor of thin Ag films of known geometry, textured as a result of sintering, was determined by means of the BET method (xenon adsorption), while their preferential crystallographic orientation (1 1 1) was estimated on the basis of XRD data. ΔR measurements were performed during various exposures of the films maintained at a constant temperature (78 or 89 K) to the flux of atomic deuterium (hydrogen) of known concentration generated on a hot tungsten filament. Every adsorption run was followed by thermal desorption. This gives a link between the ΔR measured directly in the course of adsorption and the coverage Θ determined on the basis of TDMS data, together with the BET and XRD results. It was found that at 78 K the rate of atomic deuterium (hydrogen) adsorption and recombination on the surface of sintered thin Ag films fits the Eley–Rideal (ER) mechanism, while at 89 K its overlapping with the Langmuir–Hinshelwood (LH) recombination starts to play a role. The initial sticking probability reaches 0.41 and 0.65 for D and H atoms, respectively, while the corresponding probabilities for recombination are 0.04 and 0.07. The activation energies for associative desorption of deuterium and hydrogen are 36 and 29 kJ/mol, respectively.     

Application of TEM and XPS in the interpretation of the kinetics of deuterium evolution from ultrathin TiD<Subscript><Emphasis Type="BoldItalic">y</Emphasis></Subscript>/Pd films evaporated on quartz

The kinetics of thermal evolution of deuterium from ultrathin TiD _y /Pd bilayer films has been studied by means of thermal desorption mass spectrometry (TDMS). Using a combination of transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy, we made a study of the complex structural and chemical transformations of the TiD _y /Pd film as a result of TDMS-induced evolution of deuterium and simultaneous annealing of this film. Both preparation and TDMS processing of the TiD _y /Pd bilayer films were performed in situ under UHV conditions. It was found that the high-temperature TDMS processing of an ultrathin TiD _y /Pd film, which was carried out in a relatively short time, leads to a significant film structure transformation. Energy-filtered TEM mapping of cross-section images and EDX analysis revealed extensive interdiffusion of Ti and Pd within the Ti–Pd bi-layer film. This process leads to a progressive change in chemical composition within the surface and subsurface area of the film during the TDMS processing. As the temperature of TDMS heating increases, segregation of Ti at the Pd top layer surface becomes significant. As a result, the kinetics of deuterium desorption is progressively changed during TDMS; at lower temperatures, the kinetics is limited by recombinative processes at the Pd surface, at temperatures beyond 500 K, it becomes dominated by interdiffusion of Ti into the Pd surface.     

Features of propane conversion in the presence of SmVO<Subscript>3</Subscript> and SmVO<Subscript>4</Subscript>

Features of propane conversion in the presence of samarium vanadite and samarium vanadate, both produced via solid-phase synthesis, are studied. It is shown that SmVO₃ catalyzes mainly the propane cracking process to form methane and ethylene, while SmVO₄ equally accelerates both cracking and the dehydrogenation of propane. Based on the results from catalytic experiments, energies of activation are calculated for the thermal cracking of propane (104 kJ/mol) and the conversion of propane in the presence of SmVO₃ (39 kJ/mol) and SmVO₄ (42 kJ/mol). The thermal stability of SmVO₄ in a hydrogen atmosphere is studied via temperature-programmed reduction, while SmVO₃ stability in an oxidizing environment is studied by DTA. Energies of activation for the reduction of SmVO₄ (75 kJ/mol) and the oxidation of SmVO₃ (244 kJ/mol) are calculated using the Kissinger method.     

Analysis of sputter deposited and evaporated tantalum oxide layers on SiO2 by SNMS, XPS, TDS and TRFA

Summary Tantalum oxide films with a thickness of 100 nm for the application in high power laser systems have been prepared on SiO₂-substrates by ion beam sputtering or electron beam evaporation. Comparative analysis of both groups of dielectric films has been performed with the separate bombardment mode of secondary neutral mass spectrometry SNMS, X-ray induced photoelectron spectroscopy XPS, thermal desorption spectroscopy TDS and total reflection X-ray fluorescence analysis TRFA.

---

Analyse von aufgesputterten und aufgedampften Tantaloxid-Schichten auf SiO₂ mit Hilfe von SNMS, XPS, TDS und TRFA

     

Specific features of the thermodynamics of activation in the LaNi<Subscript>5</Subscript>-H<Subscript>2</Subscript> and CeNi<Subscript>5</Subscript>-H<Subscript>2</Subscript> systems

Using heat conducting Tian—Calvet calorimetry and volumetric measurements, the first hydrogen absorption—desorption cycles in the LaNi₅-H₂ and CeNi₅-H₂ systems were studied. The pressure—composition isotherms were plotted, the equilibrium pressures of hydrogen along the absorption and desorption branches and in the region of hysteresis for different activation steps were determined, and the enthalpies of phase transitions α → β and β → α were calculated. The profiles of the heat evolution curves were analyzed. It was concluded that the mechanism of the reactions studied changes upon activation.__________Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 1, pp. 134–139, January, 2005.     

Thermodynamic properties of spinel MgAl<Subscript>2</Subscript>O<Subscript>4</Subscript>: A mass spectrometric study

The activities of oxides in stoichiometric spinel MgAl₂O₄ in the temperature range 1851–2298 K were determined from the data obtained by the Knudsen effusion mass spectrometry. The resulting Gibbs energies of spinel formation from simple oxides, the enthalpies and entropies of spinel formation from simple oxides (–12.02 ± 1.14 kJ/mol and 5.03 ± 0.56 J/(mol K), respectively), and the spinel melting enthalpy (55.81 ± 4.62 kJ/mol) satisfactorily agree with the available thermodynamic data.     

锰—铈复合氧化物催化剂表面氧的性质

氧化锰催化剂广泛用于一氧化碳常温氧化及汽车尾气的净化等,CeO_2是氧化物催化剂的优良助剂。非贵金属催化剂中添加CeO_2能提高催化剂的氧化活性已有很多报道,但有关Ce对氧化锰结构及表面氧脱附性能影响的研究尚不多见。本文运用XRD、DTA和TPD-MS等手段对共沉淀法制得的Mn-Ce复合氧化物进行了物相结构和脱氧活性研究。     

Characterization of native and heterooxide layers on compound semiconductors by combined use of surface analysis methods

Summary Structure, formation and interface reactions of anodic oxides and SiO₂ on Cd_xHg_1–xTe have been studied by means of SIMS, AES, XPS, TDMS and the electron microprobe as an example for the application of surface analysis to compound and semiconductor passivation systems.

---

Charakterisierung von Eigenoxid- und Heterooxidschichten auf Mehrkomponentenhalbleitern durch kombinierten Einsatz oberflächenanalytischer Verfahren

Zusammenfassung Aufbau, Bildungsmechanismus und Grenzflächenreaktionen von anodischen Oxiden und Quarz auf Cd_xHg_1–xTe wurden mit SIMS, AES, XPS, TDMS, SNMS und der Elektronenstrahlmikrosonde untersucht.

     

Sodium alanate nanoparticles--linking size to hydrogen storage properties

Important limitations in the application of light metal hydrides for hydrogen storage are slow kinetics and poor reversibility. To alleviate these problems doping and ball-milling are commonly applied, for NaAlH 4 leading to particle sizes down to 150 nm. By wet-chemical synthesis we have prepared carbon nanofiber-supported NaAlH 4 with discrete particle size ranges of 1-10 microm, 19-30 nm, and 2-10 nm. The hydrogen desorption temperatures and activation energies decreased from 186 degrees C and 116 kJ.mol (-1) for the largest particles to 70 degrees C and 58 kJ.mol (-1) for the smallest particles. In addition, decreasing particle sizes lowered the pressures needed for reloading. This reported size-performance correlation for NaAlH 4 may guide hydrogen storage research for a wide range of nanostructured light (metal) hydrides.     

Phase transition of RbH<Subscript>2</Subscript>PO<Subscript>4</Subscript> and its composite with SiO<Subscript>2</Subscript> studied by thermal analysis

The phase transition at T _p (~109 °C) of RbH₂PO₄ and its composite with SiO₂ has been investigated by thermal analysis here. In the case of neat RbH₂PO₄, there is a linear relationship between endothermic peak temperature (T _m) and square root of heating rate (Φ ^1/2), from which the onset temperature of phase transition can be determined. Besides, Kissinger method and another calculation method were employed to obtain the activation energy of phase transition. The detailed deduction process was presented in this paper, and the estimated activation energies are E ₁ ≈ 126.3 kJ/mol and E ₂ ≈ 129.2 kJ/mol, respectively. On the other hand, the heterogeneous doping of RbH₂PO₄ with SiO₂ as dopant facilitates its proton conduction and leads to the disappearance of jump in conductivity at T _p. The heats of transition in the composites decrease gradually with increasing the molar fraction of SiO₂ additives. In the cooling process, a new and broad exothermic peak appeared between ~95 and ~110 °C, and its intensity also changes with the SiO₂ amount. These phenomena might be related to the formation of amorphous phase of RbH₂PO₄ on the surface of SiO₂ particles due to the strong interface interaction.     

Characterization of transition metal nitride formation in rapid thermal processing (RTP)

The potential of RTP for the preparation of transition metal nitrides by reaction of metal thin films in molecular nitrogen was investigated. The films and the nitridation process were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), energy dispersive x-ray analysis (EDX) in a scanning electron microscope (SEM) and secondary neutral mass spectrometry (SNMS). The chemical states of vanadium at the utmost surface, detected by XPS, are related to V₂O₅ before RTP and to vanadium nitride, oxide and oxynitride after RTP. The deposition of a 3 nm Si top layer prevents V from oxidation and its selective removal before RTP enhances the proportion of nitride determined by XPS after RTP. From comparative experiments in a conventional tube furnace the advantages of RTP became obvious. With short process times of the RTP technique the integral amount of residual oxygen is kept low and oxide formation is largely avoided. The nitrogen content and the different polycrystalline phases formed by varying process time and temperature provide information about reactivity and the nitridation process. The nitrogen to vanadium ratio was determined by EDX and SNMS, revealing that the N content reaches saturation after only 5 seconds at 1100?°C.     

Surface oxide development on aluminum alloy 6063 during heat treatment

We report on the influence of oxygen partial pressure for the development of surface oxides covering the industrial aluminum alloy standard 6063 at temperatures ranging from room temperature to 500° C. Using an array of synchrotron-based techniques, we followed the change in oxide thickness, chemical composition, and the lateral distribution of alloying elements. The impact of the oxygen chemical potential is most visible at high temperatures where the oxide composition changes from mostly Al based to mostly Mg based. This is in stark contrast to the ultra-high vacuum (UHV) conditions where only a partial compositional transition is observed. The microscopy data demonstrate that in the UHV case, Mg segregation onto the surface occurs firstly at grain boundaries at 300° C and secondly at sites over the entire surface at 400° C. Further, the initial oxide thickness is 45 Å, as determined by XPS and XRR, decreases in all observed cases after heating to 300° C. At higher temperatures, however, the oxygen partial pressure highly influences the resulting oxide thickness as evident from our X-ray reflectivity data.     

Kinetics of formation of barium tungstate in equimolar powder mixture of BaCO<Subscript>3</Subscript> and WO<Subscript>3</Subscript>

The formation of Barium monotungstate (BaWO₄) particles in equimolar powder mixtures of BaCO₃ and WO₃ was examined under isothermal and non-isothermal conditions upon heating in air at 25–1200 °C, using thermogravimetry. Concurrence of the observed mass loss (due to the release of CO₂) to the occurrence of the formation reaction was evidenced. Accordingly, the extent of reaction (x) was determined as a function of time (t) or temperature (T). The x–t and x–T data thus obtained were processed using well established mathematical apparatus and methods, in order to characterize nature of reaction rate-determining step, and derive isothermal and non-isothermal kinetic parameters. Moreover, the reaction mixture quenched at various temperatures (600–1,000 °C) in the reaction course was analyzed by various spectroscopic and microscopic techniques, for material characterization. The results obtained indicated that the reaction rate may be controlled by unidirectional diffusion of WO₃ species across the product layer (BaWO₄), which was implied to form on the barium carbonate particles. The isothermally determined activation energy (118–125 kJ/mol) was found to be more credible than that (245 kJ/mol) determined non-isothermally.     

Body centered cubic magnesium niobium hydride with facile room temperature absorption and four weight percent reversible capacity

We have synthesized a new metastable metal hydride with promising hydrogen storage properties. Body centered cubic (bcc) magnesium niobium hydride (Mg(0.75)Nb(0.25))H(2) possesses 4.5 wt% hydrogen gravimetric density, with 4 wt% being reversible. Volumetric hydrogen absorption measurements yield an enthalpy of hydride formation of -53 kJ mol(-1) H(2), which indicates a significant thermodynamic destabilization relative to the baseline -77 kJ mol(-1) H(2) for rutile MgH(2). The hydrogenation cycling kinetics are remarkable. At room temperature and 1 bar hydrogen it takes 30 minutes to absorb a 1.5 μm thick film at sorption cycle 1, and 1 minute at cycle 5. Reversible desorption is achieved in about 60 minutes at 175 °C. Using ab initio calculations we have examined the thermodynamic stability of metallic alloys with hexagonal close packed (hcp) versus bcc crystal structure. Moreover we have analyzed the formation energies of the alloy hydrides that are bcc, rutile or fluorite.     

Synthesis of Ni-Ru alloy nanoparticles and their high catalytic activity in dehydrogenation of ammonia borane

We report the synthesis and characterization of new Ni(x)Ru(1-x) (x = 0.56-0.74) alloy nanoparticles (NPs) and their catalytic activity for hydrogen release in the ammonia borane hydrolysis process. The alloy NPs were obtained by wet-chemistry method using a rapid lithium triethylborohydride reduction of Ni(2+) and Ru(3+) precursors in oleylamine. The nature of each alloy sample was fully characterized by TEM, XRD, energy dispersive X-ray spectroscopy (EDX), and X-ray photoelectron spectroscopy (XPS). We found that the as-prepared Ni-Ru alloy NPs exhibited exceptional catalytic activity for the ammonia borane hydrolysis reaction for hydrogen release. All Ni-Ru alloy NPs, and in particular the Ni(0.74)Ru(0.26) sample, outperform the activity of similar size monometallic Ni and Ru NPs, and even of Ni@Ru core-shell NPs. The hydrolysis activation energy for the Ni(0.74)Ru(0.26) alloy catalyst was measured to be approximately 37?kJ?mol(-1). This value is considerably lower than the values measured for monometallic Ni (≈70?kJ?mol(-1)) and Ru NPs (≈49?kJ?mol(-1)), and for Ni@Ru (≈44?kJ?mol(-1)), and is also lower than the values of most noble-metal-containing bimetallic NPs reported in the literature. Thus, a remarkable improvement of catalytic activity of Ru in the dehydrogenation of ammonia borane was obtained by alloying Ru with a Ni, which is a relatively cheap metal.     

Reversible Hydrogenation of Graphene on Ni(111)—Synthesis of “Graphone”

Understanding the adsorption and reaction between hydrogen and graphene is of fundamental importance for developing graphene‐based concepts for hydrogen storage and for the chemical functionalization of graphene by hydrogenation. Recently, theoretical studies of single‐sided hydrogenated graphene, so called graphone, predicted it to be a promising semiconductor for applications in graphene‐based electronics. Here, we report on the synthesis of graphone bound to a Ni(111) surface. We investigate the formation process by X‐ray photoelectron spectroscopy (XPS), temperature‐programmed desorption (TPD), and density‐functional theory calculations, showing that the hydrogenation of graphene with atomic hydrogen indeed leads to graphone, that is, a hydrogen coverage of 1 ML (4.2 wt %). The dehydrogenation of graphone reveals complex desorption processes that are attributed to coverage‐dependent changes in the activation energies for the associative desorption of hydrogen as molecular H₂.     

Density functional study of the reaction of carbon surface oxides: the behavior of ketones

The reactions of a ketone surface oxide group have been studied on two forms of the zigzag edge and the armchair edge of a model char using density functional theory at the B3LYP/6-31G(d) level of theory. Rearrangement and surface migration reactions were found to occur much more rapidly than desorption reactions on both the zigzag and armchair edges. A number of desorption pathways characterized here go some way toward explaining the experimentally observed broad activation energy profile for CO desorption. Three separate desorption processes were characterized; on the zigzag surface two were found with activation energies of 275 and 367 kJ mol(-1), while on the armchair surface one was found with an activation energy of 296 kJ mol(-1). The activation energies for these processes were found to be insensitive to increasing the size of the char fragment. On a larger char fragment, however, an extra desorption process was found to be possible, with an activation energy of 160 kJ mol(-1).     

Fully reversible hydrogen absorption and desorption reactions with Sc(Al1−xMgx), x=0.0, 0.15, 0.20

The hydrogen storage properties of Sc(Al_1−xMg_x), x=0.0, 0.15, 0.20, have been studied by X-ray powder diffraction, thermal desorption spectroscopy, pressure-composition-isotherms and scanning electron microscopy techniques. Hydrogen is absorbed from the gas phase at 70 kPa and 400 °C under the formation of ScH₂ and aluminium with magnesium in solid solution. The reaction is fully reversible in vacuum at 500 °C and shows the hydrogenation-disproportionation-desorption-recombination (HDDR) behaviour. The activation energy of desorption was determined by the Kissinger method to 185 kJ/mol. The material is stable up to at least six absorption-desorption cycles and there is no change in particle size during cycling.     

Hydrogen storage in ni nanoparticle-dispersed multiwalled carbon nanotubes

Hydrogen storage properties of mutiwalled carbon nanotubes (MWCNTs) with Ni nanoparticles were investigated. The metal nanoparticles were dispersed on MWCNTs surfaces using an incipient wetness impregnation procedure. Ni catalysts have been known to effectively dissociate hydrogen molecules in gas phase, providing atomic hydrogen possible to form chemical bonding with the surfaces of MWCNTs. Hydrogen desorption spectra of MWCNTs with 6 wt % of Ni nanoparticles showed that approximately 2.8 wt % hydrogen was released in the range of 340-520 K. In Kissinger's plot to evaluate the nature of interaction between hydrogen and MWCNTs with Ni nanoparticles, the hydrogen desorption activation energy was measured to be as high as approximately 31 kJ/mol.H(2), which is much higher than the estimates of pristine SWNTs. C-H(n)() stretching vibrations after hydrogenation in FTIR further supported that hydrogen molecules were dissociated when bound to the surfaces of MWCNTs. During cyclic hydrogen absorption/desorption, there was observed no significant decay in hydrogen desorption amount. The hydrogen chemisorption process facilitated by Ni nanopaticles could be suggested as an effective reversible hydrogen storage method.