Electroanalysis of some common pesticides using conducting polymer/multiwalled carbon nanotubes modified glassy carbon electrode

The cyclic voltammetric behaviour of three common pesticides such as isoproturon (ISO), voltage (VOL) and dicofol (DCF) was investigated at glassy carbon electrode (GCE), multiwalled carbon nanotubes modified GCE (MWCNTs/GCE), polyaniline (PANI) and polypyrrole (PPY) deposited MWCNT/GCE. The modified electrode film was characterized by scanning electron microscopy (SEM) and X-ray diffraction analysis (XRD). The electroactive behaviour of the pesticides was realized from the cyclic voltammetric studies. The differential pulse voltammetric principle was used to analyze the above-mentioned pesticides using MWCNT/GCE, PANI/MWCNT/GCE and PPY/MWCNT/GCE. Effects of accumulation potential, accumulation time, Initial scan potential, amplitude and pulse width were examined for the optimization of stripping conditions. The PANI/MWCNT/GCE performed well among the three electrode systems and the determination range obtained was 0.01-100 mgL(-1) for ISO, VOL and DCF respectively. The limit of detection (LOD) was 0.1 microgL(-1) for ISO, 0.01 microgL(-1) for VOL and 0.05 microgL(-1) for DCF on PANI/MWCNT/GCE modified system. It is significant to note that the PANI/MWCNT/GCE modified system results in the lowest LOD in comparison with the earlier reports. Suitability of this method for the trace determination of pesticide in spiked samples was also realized.     

Electrochemical preparation of polyaniline-ionic liquid based solid phase microextraction fiber and its application in the determination of benzene derivatives

A polyaniline-ionic liquid (i.e. 1-butyl-3-methylimidazolium tetrafluoroborate, [C(4)mim][BF(4)]) composite film coated platinum wire (PANI-IL/Pt) was prepared by electrochemical method for the first time. Scanning electron microscopy image showed that the PANI-IL composite film was even and porous. When the PANI-IL/Pt was used as a fiber for the headspace solid-phase microextraction (HS-SPME) of some benzene derivatives (i.e. 1,3-dimethylbenzene, 1,2-dimethylbenzene, 1,4-dichlorobenzene, 1,2-dichlorobenzene, 1,3,5-trimethylbenzene and 1,2,4-trimethylbenzene), followed by gas chromatographic analysis, it presented excellent performance, which was much better than that of PANI/Pt and commercial polydimethylsiloxane fiber. Hence the fiber was coupled with gas chromatography for the determination of these benzene derivatives. It was found that under the optimized conditions the linear ranges were 0.04-400 μg L(-1) with correlation coefficients above 0.99, the detection limits were 9.3-48.1 ng L(-1) (S/N=3), the relative standard deviations (RSDs) were smaller than 5.1% for five successive measurements with single fiber, and the RSDs for fiber-to-fiber were 5.0-11.1% (n=3) for different benzene derivatives. The proposed method was successfully applied to the extraction and determination of benzene derivatives in waste water and tap water, and the recoveries were 87.1-108.1% for different analytes. Therefore, the PANI-IL/Pt is a promising SPME fiber.     

Polypyrrole/graphene composite-coated fiber for the solid-phase microextraction of phenols

A polypyrrole (Ppy)/graphene (G) composite was developed and applied as a novel coating for use in solid-phase microextraction (SPME) coupled with gas chromatography (GC). The Ppy/G-coated fiber was prepared by electrochemically polymerizing pyrrole and G on a stainless-steel wire. The extraction efficiency of Ppy/G-coated fiber for five phenols was the highest compared with the fibers coated with either Ppy or Ppy/graphene oxide (GO) using the same method preparation. Significantly, compared with various commercial fibers, the extraction efficiency of Ppy/G-coated fiber is better than or comparable to 85 μm CAR/PDMS fiber (best extraction efficiency of phenol, o-cresol, and m-cresol in commercial fibers) and 85 μm polyacrylate (PA) fiber (best extraction efficiency of 2,4-dichlorophenol and p-bromophenol in commercial fibers). The effects of extraction and desorption parameters such as extraction time, stirring rate, and desorption temperature and time on the extraction/desorption efficiency were investigated and optimized. The calibration curves were linear from 10 to 1000 μg/L for o-cresol, m-cresol, p-bromophenol, and 2,4-dichlorophenol, and from 50 to 1000 μg/L for phenol. The detection limits were within the range 0.34-3.4 μg/L. The single fiber and fiber-to-fiber reproducibilities were <8.3 (n=7) and 13.3% (n=4), respectively. The recovery of the phenols spiked in natural water samples at 200 μg/L ranged from 74.1 to 103.9% and the relative standard deviations were <3.7%.     

An aniline-based fiber coating for solid phase microextraction of polycyclic aromatic hydrocarbons from water followed by gas chromatography-mass spectrometry

A fiber coating from polyaniline (PANI) was electrochemically prepared and employed for solid phase microextraction (SPME) of some polycyclic aromatic hydrocarbons (PAHs) from water samples. The PANI film was directly electrodeposited on the platinum wire surface in sulfuric acid solution using cyclic voltammetry (CV) technique. The applicability of this coating was assessed employing a laboratory-made SPME device and gas chromatography with mass spectrometry (GC-MS) for the extraction of some PAHs from the headspace of aqueous samples. Application of wider potential range in CV led to a PANI with more stability against the temperature. The homogeneity and the porous surface structure of the film were examined by the scanning electron microscopy (SEM). The study revealed that this polymer is a suitable SPME fiber coating for extracting the selected PAHs. Important parameters influencing the extraction process were optimized and an extraction time of 40 min at 40 degrees C gave maximum peak area, when the aqueous sample was added with NaCl (20%, w/v). The synthesis of the PANI can be carried out conveniently and in a reproducible manner while it is rather inexpensive and stable against most of organic solvents. The film thickness of PANI can be precisely controlled by the number of CV cycles. The resulting thickness was roughly 20 microm after 20 cycles. At the optimum conditions, the relative standard deviation (RSD) for a double distilled water spiked with selected PAHs at ppb level were 8.80-16.8% (n = 3) and detection limits for the studied compounds were between 0.1-6 pg mL(-1). The performance of PANI was, also, compared with a commercial solid coated-based SPME fiber, carbowax/divinylbenzene (CW/DVB), under similar experimental conditions.     

Determination of phthalates in water samples using polyaniline-based solid-phase microextraction coupled with gas chromatography

A simple solid-phase microextraction (SPME) device, coupled with gas chromatography-flame ionization detection (GC-FID), was developed to detect trace levels of phthalates in environmental water samples. Polyaniline (PANI) was chosen as the sorbent for the SPME device and was electrochemically deposited on a stainless steel wire to achieve high thermal and mechanical stability. The porous structure of the PANI film, characterized by scanning electron microscopy (SEM), suggested large extraction capability. Key parameters were optimized and five phthalates were selected to evaluate the SPME-GC procedures. The method was also applied to the analysis of lake and river water samples. Control experiments were carried out using commercial polyacrylate (PA) fiber. The new PANI-SPME-GC method offers high accuracy, precision and sensitivity and low detection limits. Thus, the method developed could be used as a new way to monitor the trace levels of phthalates in water medium. A possible extraction mechanism was investigated using electrochemical impedance spectroscopy (EIS).     

Rapid determination of chromium(VI) in electroplating waste water by use of a spectrophotometric flow injection system

A new rapid and sensitive FI method is reported for spectrophotometric determination of trace chromium(VI) in electroplating waste water. The method is based on the reaction of Cr(VI) with sodium diphenylamine sulfonate (DPH) in acidic medium to form a purple complex (lambda(max) = 550 nm). Under the optimized conditions, the calibration curve is linear in the range 0.04-3.8 microg ml(-1) at a sampling rate of 30 h(-1). The detection limit of the method is 0.0217 microg ml(-1), and the relative standard deviation is 1.1% for eight determinations of 2 microg ml(-1) Cr(VI). The proposed method was applied to the determination of chromium in electroplating waste water with satisfactory results.     

Determination of biogenic amines in fresh and processed meat by suppressed ion chromatography-mass spectrometry using a cation-exchange column

A new method for simultaneous determination of underivatized biogenic amines based on the separation by cation-exchange chromatography and suppressed conductivity coupled with mass spectrometry detection has been developed. The method has been applied to the analysis of cadaverine, putrescine, histamine, agmatine, phenethylamine and spermidine in processed meat products. The amines were extracted from muscle tissue with methanesulfonic acid without any additional derivative step or sample clean-up. Biogenic amines were separated by the IonPac CS17 column, a cation-exchange column used with gradient elution, and detection was done by suppressed conductivity and mass spectrometry. Tyramine was simultaneously analysed by using a spectrophotometer (275 nm) before the suppressed conductivity detection. Linearity of response was obtained in the range 0.25-25 microg mL(-1). The detection limits ranged from 23 microg L(-1) for putrescine to 155 microg L(-1) for spermidine (suppressed conductivity) and from 9 microg L(-1) for agmatine to 34 microg L(-1) for spermidine (MS). Average recoveries from meat samples ranged from 85 to 97% and coefficients of variation ranged from 4.5 to 9.7%. The analysis of biogenic amines in fresh and processed meats (dry-cured, cooked and fermented products) can be used as a quality marker of raw material and for studying the relationship between their changes and the fermentation process involved in dry sausage ripening.     

Preparation and application of poly(dimethylsiloxane)/beta-cyclodextrin solid-phase microextraction fibers

A novel poly(dimethylsiloxane)/beta-cyclodextrin (PDMS/beta-CD) coating was prepared for solid-phase microextraction (SPME). The PDMS/beta-CD coating proved to have a porous structure, providing high surface areas and allowing for high extraction efficiency. The coating had a high thermal stability (340 degrees C) and a long lifetime due to its chemical binding to the fiber surface. Polar phenols and amines were used to evaluate the character of the coating fiber by headspace (HS) extraction and thermal desorption, followed by GC-FID analysis. Parameters that affected the extraction process were investigated; these include extraction time and temperature, desorption time, pH, and ionic strength of the solution. For phenols, the range of linearity of the method was 4-500 microg/L and the LOD was 1.3-2.1 microg/L. For amines, the range of linearity was 1-1000 microg/L and the LOD was 1.2-2.8 microg/L. The presence of beta-CD not only increases the thermal stability of the fiber coating, but also enhances its selectivity. Compared with commercially available SPME fibers, the new phases show better selectivity and sensitivity towards polar compounds.     

Multivariate optimization of a solid phase microextraction-headspace procedure for the determination of benzene, toluene, ethylbenzene and xylenes in effluent samples from a waste treatment plant

A method based on solid-phase microextraction (SPME) and gas chromatography with flame ionization detection (GC-FID) has been optimized for the determination of benzene, toluene, ethylbenzene and xylenes (BTEX) in water released from a waste treatment plant. The extraction step was optimized using fractional factorial and central composite designs including the following experimental factors: saline concentration; extraction time; desorption time; agitation velocity; headspace volume. A multiple function was used to describe the experimental conditions for simultaneous extraction of the compounds. The procedure, based on direct SPME at 50 degrees C, using a polydimethylsiloxane fiber, showed good linearity (r>0.997 over a concentration range 2-200 microg L(-1)) and repeatability (relative standard deviation (RSD)<4.23%) for all compounds, with limits of detection ranging from 0.05 to 0.28 microg L(-1), and limits of quantification ranging from 0.14 to 0.84 microg L(-1). Concentrations of the target compounds in these samples were between 145.8 and 1891 microg L(-1).     

Novel proton-type ionic liquid doped polyaniline for the headspace solid-phase microextraction of amines

A novel proton-type ionic liquid doped polyaniline (HIL-doped PANI) coating was presented, which was prepared on a stainless steel wire by electrodeposition in an aqueous solution containing aniline and 1-sulfobutyl-3-methylimidazolium hydrosulfate. The HIL-doped PANI coating showed granular nanostructure and had large specific surface. When it was applied to the headspace solid-phase microextraction of several amines (i.e., aniline, N-methylaniline, 3-methylaniline, 2-chloroaniline and 3-chloroaniline), it showed high extraction efficiency. The enrichment factors were 191.8–343.9 for different amines, much higher than those of common PANI and commercial polydimethylsiloxane/divinylbenzene coatings. Coupled with gas chromatographic analysis, the linear ranges were 0.097–100 μg/L with correlation coefficients above 0.9942, and the detection limits were 0.012–0.048 μg/L (S/N = 3) for different amines. The relative standard deviations (RSD) were smaller than 8.1% for five successive measurements with single fiber and the fiber-to-fiber RSDs were 8.6–13.8% (n = 5) for these amines. The proposed method was successfully applied to the extraction and determination of amines in organic waste water samples, and the recoveries were 78.3–112.8% for different analytes.     

液相微萃取-离子色谱法测定污水中痕量芳香胺

基于中空纤维液相微萃取技术,建立了河流污水中两种芳香胺类物质（邻甲苯胺和对氯苯胺）的离子色谱分析方法。采用中空纤维液相微萃取和离子色谱联用技术,对中空纤维萃取条件进行优化。优化的萃取条件：萃取溶剂为正辛醇,供体相中NaOH的浓度为0.01mol/L, NaCl的浓度为500g/L,接受相中HCl的浓度为0.1 mol/L,搅拌速度为430r/min,萃取时间为30min,在优化条件下,邻甲苯胺的富集倍数为88倍,对氯苯胺的富集倍数为124倍。供体相中邻甲苯胺和对氯苯胺的浓度在0.005–0.1mg/L范围内成良好线性,相关系数为0.9998-0.9999 ,检出限为0.2-0.5μg /L,相对标准偏差为0.85-3.38 %。结论：这种方法操作简单,环境友好,提高了离子色谱检测芳香胺类物质的灵敏度。     

Solid-Phase Microextraction of Aliphatic Alcohols Based on Polyaniline Coated Fibers

The efficiency of polyaniline (PANI), coated gold wire was investigated for use as a fiber for solid-phase microextraction (SPME). Aniline monomers were electropolymerized on gold wires by applying a constant current to an acetate buffer containing NaClO₄ as supporting electrolyte for 30 min. These fibers were used for the extraction of some aliphatic alcohols from gaseous samples. The results obtained proved the ability of PANI fiber for sampling organic compounds from gaseous samples. From this work, optimum conditions for preparation and conditioning of fibers and for the extraction of analytes from gaseous samples were obtained. Under optimum conditions, one fiber was used for several equivalent analyses and the relative standard deviations (RSD) were <7% (n=6). However, fiber to fiber reproducibility was <9% (n=6). This fiber is firm and durable and is simply prepared. Calibration graphs were linear in the range: 0.1–10 g mL^–1 for aliphatic alcohols; the detection limit range was 15–75 ng mL^–1 (S/N=3) using a flame ionization detector.     

Determination of phthalates in water using fiber introduction mass spectrometry

Fiber introduction mass spectrometry (FIMS)-a direct coupling of SPME and MS-using selective ion monitoring (SIM) was used to detect and quantify dimethylphthalate (DMP), diethylphthalate (DEP) and dipropylphthalate (DPP) in mineral water. In FIMS, a chromatographic silicone septum is the only barrier between ambient and the high-vacuum mass spectrometer, permitting direct introduction of the SPME fiber into the ionization region of the equipment. After their thermal desorption and ionization and dissociation, the extracted phthalates are detected and quantitated by MS. Three types of SPME fibers were screened for best analyte sorption/desorption behaviors: 100 microm polydimethylsiloxane (PDMS), 65 microm polydimethylsiloxane/divinylbenzene (PDMS/DVB) and 65 microm Carbowax/divinylbenzene (CW/DVB). The PDMS/DVB and CW/DVB fibers were then evaluated for precision, and quantitative figures of merit were assessed for extractions using the PDMS/DVB fiber, which displayed the best overall performance. FIMS with the PDMS/DVB fiber allows simple extraction and MS detection and quantitation of DMP in water with good linearity and precision, and at concentrations as low as 3.6 microg L(-1). The LD and LQ of FIMS are below the maximum phthalate concentration allowed by the USEPA for drinking water (6 microg L(-1)).     

石墨烯层层键合固相微萃取纤维的制备及对多环芳烃的检测

通过3-巯基丙基三甲氧基硅烷处理银层包裹的不锈钢纤维,得到Si-OH功能化的纤维,氧化石墨烯被层层键合到Si-OH功能化的纤维上,还原氧化石墨烯得到石墨烯层层键合的固相微萃取纤维。该方法制备的新型石墨烯层层键合的固相微萃取纤维具有制备简单,机械性能强,萃取涂层牢固,萃取能力强等优势。建立具有较宽线性范围(5~200μg/L)、较低检测限(0.007~0.09μg/L)的固相微萃取-气相色谱分析方法,用该方法测定河水和雨水中多环芳烃的含量。所制备的新型纤维重现性好、稳定性高、萃取能力强,可实现对多环芳烃的痕量检测。     

Preparation of a polymeric ionic liquid-coated solid-phase microextraction fiber by surface radical chain-transfer polymerization with stainless steel wire as support

Polymeric 1-vinyl-3-octylimidazolium hexafluorophosphate was synthesized in situ on stainless steel wire by surface radical chain-transfer polymerization and used as sensitive coatings in solid-phase microextraction. The outer surface of the stainless steel wire was firstly coated with microstructured silver layer via silver mirror reaction and then functionalized with self-assembled monolayers of 1,8-octanedithiol, which acted as chain transfer agent in the polymerization. Coupled to gas chromatography, extraction performance of the fiber was studied with both headspace and direct-immersion modes using benzene, toluene, ethylbenzene and xylenes (BTEX), phenols and polycyclic aromatic hydrocarbon (PAHs) as model analytes. In combination with the microstructured silver layer, the PIL-coated fiber exhibited high extraction efficiency. Linear ranges for BTEX with headspace mode were in the range of 0.2-1000 μg L(-1) for benzene, and 0.1-1000 μg L(-1) for toluene, ethylbenzene and xylenes. Limits of detection (LODs) were from 0.02 to 0.05 μg L(-1). Wide linear ranges of direct-immersion mode for the extraction of several phenols and PAHs were also obtained with correlation coefficients (R) from 0.9943 to 0.9997. The proposed fiber showed good durability with long lifetime. RSDs of 56 times extraction were still in an acceptable range, from 8.85 to 22.8%.     

Hydride generation for the direct determination of trace and ultra-trace level of arsenic and antimony in waters using derivative atomic absorption spectrometry

A new method is developed for the direct determination of trace and ultra-trace level of arsenic and antimony in waters by hydride generation derivative atomic absorption spectrometry (DHGAAS). The signal model and fundamentals of DHGAAS are described. The effects of atomization temperature, argon flow rate, acidity and concentration of KBH(4)and KI were investigated and analytical conditions were optimized. The sensitivities for arsenic and antimony were increased 36.4 and 27.6 times better than those of conventional hydride generation atomic absorption spectrometry (HGAAS). For a 2 mV min(-1) sensitivity range setting, the characteristic concentration was 0.003 microg L(-1) for arsenic and 0.004 microg L(-1)for antimony, and the detection limits (3sigma) were 0.015 micro g L(-1) for arsenic and 0.020 microg L(-1) for antimony. The proposed method was applied to the determination of arsenic and antimony in several water samples with satisfactory results.     

Quantitation of mercapturic acids from acrylamide and glycidamide in human urine using a column switching tool with two trap columns and electrospray tandem mass spectrometry

A sensitive and specific electrospray tandem mass spectrometry method using a column switching unit with two trap columns was established to quantify the mercapturates (MAs) of acrylamide (AA) and glycidamide (GA) in human urine. A specially endcapped material was applied for trapping the hydrophilic MAs and a pre-trap column was used to remove lipophilic compounds from the directly injected urine to protect the trap column. The limits of quantitation for AA-MA and GA-MA in urine were 0.5 microg/L and 1 microg/L, respectively. Urine was spiked with deuterated internal standards and injected directly into LC-MS/MS. Urine of smokers (n=13) revealed the highest concentrations of AA-MA and GA-MA in the range of 61-706 microg/L and 5-54 microg/L, respectively. Lower levels for AA-MA (14-102 microg/L) and GA-MA (1-11 microg/L) were detected in non-smokers (n=13).     

Nano-structured polyaniline-ionic liquid composite film coated steel wire for headspace solid-phase microextraction of organochlorine pesticides in water

A novel nano-structured polyaniline-ionic liquid (i.e. 1-butyl-3-methylimidazolium hexafluorophosphate, BMIPF(6)) composite (BPAN) film coated steel wire was prepared by electrochemical deposition. Scanning electron microscopy images showed that the obtained porous BPAN coating consisted of nanofibers, whose diameter ranged from 50 to 80 nm. Furthermore, the novel nano-structured composite coating was very stable at relatively high temperatures (up to 350 °C) and it could be used for more 250 times without obvious decrease of the extraction efficiency. The novel BPAN coating was used for the headspace solid-phase microextraction (HS-SPME) of organochlorine pesticides (i.e. hexachlorocyolohexane, dichlorodiphenyldichloroethylene, dichlorodiphenyldichloroethane, dichlorodiphenyltrichloroethane), coupled with gas chromatography-electron capture detection (GC-ECD). The BPAN coating showed better analytical capability on the whole compared with common polyaniline (PANI) and polydimethylsiloxane (PDMS) coatings. The key parameters influencing extraction efficiency were investigated and optimized, including desorption time, stirring speed, extraction temperature, extraction time and ionic strength. The relative standard deviations (RSDs) for single fiber repeatability ranged from 2.3 to 8.7% (n=6) and the RSDs for fiber-to-fiber reproducibility (n=6) were 4.2-12.1%, respectively. The linear ranges exceeded three magnitudes with correlation coefficients above 0.99. The detection limits were 0.12-0.31 ng L(-1). The proposed method was successfully applied for the determination of organochlorine pesticides in lake water, waste water and sewage treatment plant effluent with good recoveries from 88.9 to 112.9%.     

Analysis of fumonisins B(1), B(2) and B(3) in corn-based baby food by pressurized liquid extraction and liquid chromatography/tandem mass spectrometry

A sensitive and reliable method using pressurized liquid extraction (PLE) and liquid chromatography (LC)/electrospray ionization (ESI) tandem mass spectrometry with a triple quadrupole (QqQ) analyzer has been developed for the analysis of fumonisin B(1) (FB(1)), fumonisin B(2) (FB(2)) and fumonisin B(3) (FB(3)) in corn-based baby foods. Influence of several extraction parameters that affect PLE efficiency such as temperature, pressure, solvent extraction, number of cycles and dispersant/clean-up agents were studied. The selected PLE operating method was: 3g of sample was packed into 11 ml stainless-steel cell and fumonisins were extracted with methanol at 40 degrees C, 34 atm in one cycle of 5 min at 60% flush. The analytes were ionized in ESI operating with positive ion mode and identified by selecting two monitoring transitions, permitting quantification and confirmation in a single injection. Recoveries ranged from 68% to 83% at fortification levels of 200 microg kg(-1) with relative standard deviation (RSD) from 4% to 12%. The limits of quantification were from 2 microg kg(-1) for FB(1) and FB(2), and 5 microg kg(-1) for FB(3), which are below the maximum residue level established by the European Union legislation in infant formulas. The proposed method was successfully applied to the analysis of twenty seven samples of baby food products collected from different markets, and one positive sample with a content of 15.9 microg kg(-1) for FB(1), 9.2 microg kg(-1)for FB(2) and 5.8 microg kg(-1) for FB(3) was obtained. Given the simplicity and potential of the proposed procedure, its application for safety control is recommended.     

Novel multiwalled carbon nanotubes–polyaniline composite film coated platinum wire for headspace solid-phase microextraction and gas chromatographic determination of phenolic compounds

A novel multiwalled carbon nanotubes–polyaniline composite (MWCNTs–PANI) film coated platinum wire was fabricated through electrochemical deposition. The coating was characterized by scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectrophotometry and thermogravimetry. It was found that the coating was porous and had large specific area and adsorption capacity; in the composite MWCNTs and polyaniline interacted with each other and the film kept stable up to 320 °C. The as-made fiber was used for the headspace solid-phase microextraction (HS-SPME) of some phenolic compounds (i.e. 2-chlorophenol, 2,4-dichlorophenol, 2-methylphenol, 3-methylphenol, 2,6-dimethylphenol, 2-nitrophenol), followed by gas chromatographic analysis. The MWCNTs–PANI coating showed better analytical performance than PANI. Under the optimized conditions, the detection limits were 1.89–65.9 ng L⁻¹, the relative standard deviations (RSDs) were 2.7–6.5% for six successive measurements with single fiber, the RSDs for fiber-to-fiber were 5.2–12.4%, the linear ranges exceeded two magnitudes with correlation coefficient above 0.992. The fiber could be used for more than 250 times without decrease of efficiency. The proposed method was successfully applied to the extraction and determination of phenolic compounds in water sample, and the recoveries were 87.7–111.5% for different analytes. In addition, the fiber also presented advantages of easy preparation and low cost. Therefore, it is a promising SPME fiber.