Tuning the properties of hydrogen-bonded block copolymer worm gels prepared via polymerization-induced self-assembly

Polymerization-induced self-assembly (PISA) is exploited to design hydrogen-bonded poly(stearyl methacrylate)-poly(benzyl methacrylate) [PSMA-PBzMA] worm gels in n-dodecane. Using a carboxylic acid-based RAFT agent facilitates hydrogen bonding between neighboring worms to produce much stronger physical gels than those prepared using the analogous methyl ester-based RAFT agent. Moreover, tuning the proportion of these two types of end-groups on the PSMA chains enables the storage modulus (G′) of a 20% w/w worm gel to be tuned from ∼4.5 kPa up to ∼114 kPa. This is achieved via two complementary routes: (i) an in situ approach using binary mixtures of acid- and ester-capped PSMA stabilizer chains during PISA or (ii) a post-polymerization processing strategy using a thermally-induced worm-to-sphere transition to mix acid- and ester-functionalized spheres at 110 °C that fuse to form worms on cooling to 20 °C. SAXS and rheology studies of these hydrogen-bonded worm gels provide detailed insights into their inter-worm interactions and physical behavior, respectively. In the case of the carboxylic acid-functionalized worms, SAXS provides direct evidence for additional inter-worm interactions, while rheological studies confirm both a significant reduction in critical gelation concentration (from approximately 10% w/w to 2–3% w/w) and a substantial increase in critical gelation temperature (from 41 °C to 92 °C). It is remarkable that a rather subtle change in the chemical structure results in such improvements in gel strength, gelation efficiency and gel cohesion.

Carboxylic acid-capped diblock copolymer worms are prepared in n-dodecane via polymerization-induced self-assembly. Varying the proportion of terminal carboxylic acid groups modulates the inter-worm H-bonding interactions and hence the gel modulus.     

Can polymersomes form colloidosomes?

Hydroxy-functionalized polymersomes (or block copolymer vesicles) were prepared via a facile one-pot RAFT aqueous dispersion polymerization protocol and evaluated as Pickering emulsifiers for the stabilization of emulsions of n-dodecane emulsion droplets in water. Linear polymersomes produced polydisperse oil droplets with diameters of ～50 μm regardless of the polymersome concentration in the aqueous phase. Introducing an oil-soluble polymeric diisocyanate cross-linker into the oil phase prior to homogenization led to block copolymer microcapsules, as expected. However, TEM inspection of these microcapsules after an alcohol challenge revealed no evidence for polymersomes, suggesting these delicate nanostructures do not survive the high-shear emulsification process. Thus the emulsion droplets are stabilized by individual diblock copolymer chains, rather than polymersomes. Cross-linked polymersomes (prepared by the addition of ethylene glycol dimethacrylate as a third comonomer) also formed stable n-dodecane-in-water Pickering emulsions, as judged by optical and fluorescence microscopy. However, in this case the droplet diameter varied from 50 to 250 μm depending on the aqueous polymersome concentration. Moreover, diisocyanate cross-linking at the oil/water interface led to the formation of well-defined colloidosomes, as judged by TEM studies. Thus polymersomes can indeed stabilize colloidosomes, provided that they are sufficiently cross-linked to survive emulsification.     

Pickering emulsions co-stabilised by cellulose nanofibres and nicotinamide mononucleotide

Cellulose - Emulsified solid particles adsorbed at the oil–water interface can stabilise Pickering emulsions by acting as a physical barrier to the coalescence of oil droplets. Cellulose...     

Hydrophilic polymer foams with well‐defined open‐cell structure prepared from pickering high internal phase emulsions

Open‐cell hydrophilic polymer foams are prepared through oil‐in‐water Pickering high internal phase emulsions (HIPEs). The Pickering HIPEs are stabilized by commercial titania (TiO₂) nanoparticles with adding small amounts of non‐ionic surfactant Tween85. The morphologies, such as average void diameter and interconnectivity, of the foams can be tailored easily by varying the TiO₂ nanoparticles and Tween85 concentrations. Further, investigation of the HIPE stability, emulsion structure and the location of TiO₂ nanoparticles in resulting foams shows that the surfactant tends to occupy the oil‐water interface at the contact point of adjacent droplets, where the interconnecting pores are hence likely to be formed after the consolidation of the continuous phase. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Sterilizable gels from thermoresponsive block copolymer worms

Biocompatible hydrogels have many applications, ranging from contact lenses to tissue engineering scaffolds. In most cases, rigorous sterilization is essential. Herein we show that a biocompatible diblock copolymer forms wormlike micelles via polymerization-induced self-assembly in aqueous solution. At a copolymer concentration of 10.0 w/w %, interworm entanglements lead to the formation of a free-standing physical hydrogel at 21 °C. Gel dissolution occurs on cooling to 4 °C due to an unusual worm-to-sphere order-order transition, as confirmed by rheology, electron microscopy, variable temperature (1)H NMR spectroscopy, and scattering studies. Moreover, this thermo-reversible behavior allows the facile preparation of sterile gels, since ultrafiltration of the diblock copolymer nanoparticles in their low-viscosity spherical form at 4 °C efficiently removes micrometer-sized bacteria; regelation occurs at 21 °C as the copolymer chains regain their wormlike morphology. Biocompatibility tests indicate good cell viabilities for these worm gels, which suggest potential biomedical applications.     

Non-covalent reconfigurable microgel colloidosomes with a well-defined bilayer shell

Microgels are extremely interfacially active and are widely used to stabilize emulsions. However, they are commonly used to stabilize oil-in-water emulsions due to their intrinsic hydrophilicity and initially dispersed in water. In addition, there have been no attempts to control microgel structural layers that are formed at the interface and as a result it limits applications of microgel in advanced materials. Here, we show that by introducing octanol into poly(N-isopropylacrylamide-co-methacrylic acid) (PNIPAM-co-MAA) microgels, octanol-swollen microgels can rapidly diffuse from the initially dispersed oil phase onto the water droplet surface. This facilitates the formation of microgel-laden interfacial layers with strong elastic responses and also generates stable inverse water-in-oil Pickering emulsions. These emulsions can be used as templates to produce microgel colloidosomes, herein termed ‘microgelsomes’, with shells that can be fine-tuned from a particle monolayer to a well-defined bilayer. The microgelsomes can then be used to encapsulate and/or anchor nanoparticles, proteins, vitamin C, bio-based nanocrystals or enzymes. Moreover, the programmed release of these substances can be achieved by using ethanol as a trigger to mediate shell permeability. Thus, these reconfigurable microgelsomes with a microgel-bilayer shell can respond to external stimuli and demonstrate tailored properties, which offers novel insights into microgels and promise wider application of Pickering emulsions stabilized by soft colloids.

Inverse W/O Pickering emulsions and reconfigurable microgelsomes with a well-defined bilayer structure are prepared from octanol-swollen PNIPAM-co-MAA microgels and the combination of binary microgels, which promise wider application of soft colloids.     

Simple, reversible emulsion system switched by pH on the basis of chitosan without any hydrophobic modification

Chitosan without hydrophobic modification is not a good emulsifier itself. However, it has a pH-tunable sol-gel transition due to free amino groups along its backbone. In the present work, a simple reversible Pickering emulsion system based on the pH-tunable sol-gel transition of chitosan was developed. At pH > 6.0, as adjusted by NaOH, chitosan was insoluble in water. Chitosan nanoparticles or micrometer-sized floccular precipitates were formed in situ. These chitosan aggregates could adsorb at the interface of oil and water to stabilize the o/w emulsions, so-called Pickering emulsions. At pH < 6.0, as adjusted by HCl, chitosan was soluble in water. Demulsification happened. Four organic solvents (liquid paraffin, n-hexane, toluene, and dichloromethane) were chosen as the oil phase. Reversible emulsions were formed for all four oils. Chitosan-based Pickering emulsions could undergo five cycles of emulsification-demulsification with only a slight increase in the emulsion droplet size. They also had good long-term stability for more than 2 months. Herein, we give an example of chitosan without any hydrophobic modification to act as an effective emulsifier for various oil-water systems. From the results, we have determined that natural polymers with a stimulus-responsive sol-gel transition should be a good particulate emulsifier. The method for in situ formation of pH-responsive Pickering emulsions based on chitosan will open up a new route to the preparation of a wide range of reversible emulsions.     

Effects of Surface Properties on Rheological and Interfacial Properties of Pickering Emulsions Prepared by Fumed Silica Suspensions Pre-Adsorbed Poly(N-Isopropylacrylamide)

The hydrophobic fumed silica suspensions physically pre-adsorbed poly(N-isopropylacrylamide) (PNIPAM) in water could prepare oil dispersed in water (O/W) Pickering emulsion by mixing of silicone oil. The resulting Pickering emulsions were characterized by the measurements of volume factions of emulsified silicone oil, adsorbed amounts of the silica suspensions, oil droplet size, and some rheological responses, such as stress-strain sweep curve and dynamic viscoelastic moduli as a function of the added amount of PNIPAM. Moreover, their characteristics were compared with those of the O/W Pickering emulsions prepared by the hydrophilic fumed silica suspensions pre-adsorbed PNIPAM. For the emulsions prepared by the hydrophobic silica suspensions, an increase in the added amount of PNIPAM led to (1) a decrease in the volume fraction of the emulsified oil in the emulsified phase, (2) both the size of oil droplets and the adsorbed amount of the corresponding silica suspensions being almost constant, except for the higher added amounts, and (3) both the storage modulus (G′) and the yield shear strain being constant. The term of 1 is the same for the emulsions prepared by the hydrophilic silica suspensions, whereas both the adsorbed amount of the corresponding silica suspension and the G′ value increase and both the droplet size and the yield shear strain decrease with an increase in the added amount of PNIPAM. The differences between the rheological properties of the emulsions prepared by the hydrophilic silica suspensions and those by the hydrophobic ones are attributed to the hydrophobic interactions of the flocculated silica particles in the Pickering emulsions.     

Water-dispersible non-aqueous emulsions stabilized by a poly(butadiene)-b-poly(2-vinylpyridine) block copolymer

Submicron non-aqueous emulsions, of interest for biomedical and cosmetic formulations, were developed for the system comprising poly(ethylene glycol) (PEG) 400 and Miglyol 812, an enzymatic degradable liquid glycerine ester. These emulsions, with PEG 400 as continuous phase and Miglyol 812 droplets, in the size range of 200 nm, were stabilized by a poly(butadiene)-b-poly(2-vinylpyridine) (PBut-b-P2VP) block copolymer with a composition close to 50/50 wt%. The droplet size, stability and the rheological characteristics were examined as a function of the copolymer concentration. An original aspect of these anhydrous emulsions, with a water miscible continuous phase, is their water dispersibility without additional surfactant. In fact, the initial anhydrous emulsion is sterically stabilized and after water addition at low pH, the protonated P2VP sequence of the copolymer provides the electro-steric stabilization. This oil-in-water emulsion is characterized by sub micron sized Miglyol 812 droplets in an aqueous phase of PEG 400 and water at pH 1.     

Effect of varying the oil phase on the behavior of pH-responsive latex-based emulsifiers: demulsification versus transitional phase inversion

Sterically stabilized polystyrene latexes (previously described by Amalvy, J. I.; et al. Chem. Commun. 2003, 1826) were evaluated as pH-responsive particulate emulsifiers for the preparation of both oil-in-water and water-in-oil emulsions. The steric stabilizer was a well-defined AB diblock copolymer where A is poly(2-(dimethylamino)ethyl methacrylate) and B is poly(methyl methacrylate). Several parameters were varied during the emulsion preparation, including the polarity of the oil phase, the latex concentration, surface concentration of copolymer stabilizer, and solution pH. Nonpolar oils such as n-dodecane gave oil-in-water emulsions, and polar oils such as 1-undecanol produced water-in-oil emulsions. In both cases, these emulsions proved to be stimulus-responsive: demulsification occurred rapidly on adjusting the solution pH. Oils of intermediate polarity such as methyl myristate or cineole led to emulsions that underwent transitional inversion on adjusting the solution pH. All emulsions were polydisperse and typically ranged from 40 to 400 microm diameter, as judged by optical microscopy and Malvern Mastersizer measurements. Critical point drying of the emulsion droplets, followed by scanning electron microscopy studies, confirmed that the latex particles were adsorbed as a single monolayer at the oil/water interface, as anticipated.     

Silica nanoparticle-loaded thermoresponsive block copolymer vesicles: a new post-polymerization encapsulation strategy and thermally triggered release

A thermoresponsive amphiphilic diblock copolymer that can form spheres, worms or vesicles in aqueous media at neutral pH by simply raising the dispersion temperature from 1 °C (spheres) to 25 °C (worms) to 50 °C (vesicles) is prepared via polymerization-induced self-assembly (PISA). Heating such an aqueous copolymer dispersion from 1 °C up to 50 °C in the presence of 19 nm glycerol-functionalized silica nanoparticles enables this remarkable ‘shape-shifting’ behavior to be exploited as a new post-polymerization encapsulation strategy. The silica-loaded vesicles formed at 50 °C are then crosslinked using a disulfide-based dihydrazide reagent. Such covalent stabilization enables the dispersion to be cooled to room temperature without loss of the vesicle morphology, thus aiding characterization and enabling the loading efficiency to be determined as a function of both copolymer and silica concentration. Small-angle X-ray scattering (SAXS) analysis indicated a mean vesicle membrane thickness of approximately 20 ± 2 nm for the linear vesicles and TEM studies confirmed encapsulation of the silica nanoparticles within these nano-objects. After removal of the non-encapsulated silica nanoparticles via multiple centrifugation–redispersion cycles, thermogravimetric analysis indicated that vesicle loading efficiencies of up to 86% can be achieved under optimized conditions. Thermally-triggered release of the silica nanoparticles is achieved by cleaving the disulfide bonds at 50 °C using tris(2-carboxyethyl)phosphine (TCEP), followed by cooling to 20 °C to induce vesicle dissociation. SAXS is also used to confirm the release of silica nanoparticles by monitoring the disappearance of the structure factor peak arising from silica–silica interactions.

A loading efficiency of up to 86% is achieved for silica nanoparticles encapsulated within crosslinkable redox-sensitive thermoresponsive diblock copolymer vesicles in water at 50 °C; triggered release is also demonstrated for this system.     

Using the gravitational energy of water to generate power by separation of charge at interfaces

When a fluid comes into contact with a solid surface, charge separates at the interface. This study describes a method that harvests the gravitational energy of water—available in abundance naturally, such as in rain and rivers—through the separation of charge at the interface. Essentially, it is found that water can be charged by flowing it across a solid surface under its own weight; thus, a continuous flow of water can produce a constant supply of power. After optimizing the system, a power of up to ∼170 μW (per Teflon tube of 2 mm in diameter) can be generated. The efficiency, defined as the energy generated by the system over the gravitational energy that the water losses, can reach up to ∼3–4%. In order to generate a continuous stream of positively-charged water, there should also be a constant production of negatively-charged species in the system. Experimental results suggest that the negative charge transfers constantly to the atmosphere due to dielectric breakdown of air. With regards to applications related to high electrical potential of water droplets, the amount of charge generated in a single water droplet is found to be equivalent to that produced by charging the water droplet with a high-voltage power supply operated at ∼5 kV. In general, the energy generated is clean, renewable, and technically simple and inexpensive to produce.     

Recent Advances in Polymerization-Induced Self-Assembly (PISA) Syntheses in Non-Polar Media

It is well-known that polymerization-induced self-assembly (PISA) is a powerful and highly versatile technique for the rational synthesis of colloidal dispersions of diblock copolymer nanoparticles, including spheres, worms or vesicles. PISA can be conducted in water, polar solvents or non-polar media. In principle, the latter formulations offer a wide range of potential commercial applications. However, there has been just one review focused on PISA syntheses in non-polar media and this prior article was published in 2016. The purpose of the current review article is to summarize the various advances that have been reported since then. In particular, PISA syntheses conducted using reversible addition-fragmentation chain-transfer (RAFT) polymerization in various n-alkanes, poly(α-olefins), mineral oil, low-viscosity silicone oils or supercritical CO₂ are discussed in detail. Selected formulations exhibit thermally induced worm-to-sphere or vesicle-to-worm morphological transitions and the rheological properties of various examples of worm gels in non-polar media are summarized. Finally, visible absorption spectroscopy and small-angle X-ray scattering (SAXS) enable in situ monitoring of nanoparticle formation, while small-angle neutron scattering (SANS) can be used to examine micelle fusion/fission and chain exchange mechanisms.     

Production of large quantities of “Janus” nanoparticles using wax-in-water emulsions

For the first time, large amount of Janus silica particles as small as 100 nm in diameter were prepared through a simple method based on the elaboration of Pickering emulsions of wax-in-water. Controlling the kinetic stabilization of wax droplets allows the fabrication of gram-sized quantities of regular asymmetric inorganic particles with high yield. In fact, our method is based on a limited coalescence process, which allows one to predict the quantity of interface which is produced when working with a known mass of wax, and thus to be sure that all introduced silica particles are adsorbed on the wax surface. To this end, the hydrophilic surface of the silica particles was made partially hydrophobic by adsorbing a known amount of surfactant: cetyltrimethylammonium bromide (CTAB). Varying the concentration in surfactant results in tuning the penetration rate of the particles in the wax droplets, leading to various dimension of the modified area. The broken spherical symmetry of the particle surface was thereafter revealed by the selective adsorption of gold nanoparticles on the amino-modified surface.     

Magnetic Pickering emulsions stabilized by Fe3O4 nanoparticles

Superparamagnetic Fe(3)O(4) nanoparticles prepared by a classical coprecipitation method were used as the stabilizer to prepare magnetic Pickering emulsions, and the effects of particle concentration, oil/water volume ratio, and oil polarity on the type, stability, composition, and morphology of these functional emulsions were investigated. The three-phase contact angle (θ(ow)) of the Fe(3)O(4) nanoparticles at the oil-water interface was evaluated using the Washburn method, and the results showed that for nonpolar and weakly polar oils of dodecane and silicone, θ(ow) is close to 90°, whereas for strongly polar oils of butyl butyrate and 1-decanol, θ(ow) is far below 90°. Inherently hydrophilic Fe(3)O(4) nanoparticles can be used to prepare stable dodecane-water and silicone-water emulsions, but they cannot stabilize butyl butyrate-water and decanol-water mixtures with macroscopic phase separation occurring, which is in good agreement with the contact angle data. Emulsions are of the oil-in-water type for both dodecane and silicone oil, and the average droplet size increases with an increase in the oil volume fraction. For stable emulsions, not all of the particles are adsorbed to drop interfaces; the fraction adsorbed decreases with an increase in the initial oil volume fraction. Changes in the particle concentration have no obvious influence on the stability of these emulsions, even though the droplet size decreases with concentration.     

Sodium caseinate as a particulate emulsifier for making indefinitely recycled pH-responsive emulsions

pH-responsive emulsions are one of the simplest and most readily implementable stimuli-responsive systems. However, their practical uses have been greatly hindered by cyclability. Here, we report a robust pH-responsive emulsion prepared by utilizing pure sodium caseinate (NaCas) as the sole emulsifier. We demonstrate that the emulsification/demulsification of the obtained NaCas-stabilized emulsion can be triggered by simply changing the pH value over 100 cycles, which has never been observed in any protein-stabilized emulsion system. The NaCas-stabilized emulsion maintains its pH-responsive properties even in a saturated salt solution (NaCl ∼ 6.1 M) or seawater. We illustrate how NaCas functions in pH-responsive emulsions and show that when conventional nanoparticles such as zein protein or bare SiO₂ particles were coated with a layer of NaCas, the resulting formulated emulsions could be switched on and off over 10 cycles. The unique properties of NaCas thus enable the engineering of conventional Pickering emulsions to pH-responsive Pickering emulsions. Finally, we have integrated catalytically active gold (Au) nanoclusters (NCs) into the NaCas protein and then utilized them to produce emulsions. Remarkably, these NaCas–Au NCs assembled at the oil–water interface exhibited excellent catalytic activity and cyclability, not only in aqueous solution, but also in complicated seawater environments.

An unprecedented pH-responsive emulsion is shaped by utilizing pure sodium caseinate (NaCas) as the sole emulsifier for recyclable interfacial catalysis. This emulsion could be reversibly switched on and off over 100 cycles.     

New Pickering emulsions stabilized by bacterial cellulose nanocrystals

We studied oil in water Pickering emulsions stabilized by cellulose nanocrystals obtained by hydrochloric acid hydrolysis of bacterial cellulose. The resulting solid particles, called bacterial cellulose nanocrystals (BCNs), present an elongated shape and low surface charge density, forming a colloidal suspension in water. The BCNs produced proved to stabilize the hexadecane/water interface, promoting monodispersed oil in water droplets around 4 μm in diameter stable for several months. We characterized the emulsion and visualized the particles at the surface of the droplets by scanning electron microscopy (SEM) and calculated the droplet coverage by varying the BCN concentration in the aqueous phase. A 60% coverage limit has been defined, above which very stable, deformable droplets are obtained. The high stability of the more covered droplets was attributed to the particle irreversible adsorption associated with the formation of a 2D network. Due to the sustainability and low environmental impact of cellulose, the BCN based emulsions open opportunities for the development of environmentally friendly new materials.     

Synthesis of Dual‐Stimuli‐Responsive Microcontainers with Two Payloads in Different Storage Spaces for Preprogrammable Release

Stimuli‐responsive microcontainers have become a major topic of interest, from fundamental aspects to applications in materials science. However, microcontainers that enable the loading of multiple species and programmable release are mostly unexplored. Herein, we describe the design and synthesis of a dual‐responsive organic/inorganic hybrid microcontainer with two payloads in separate storage spaces that is formed by the rapid UV‐initiated polymerization of Pickering emulsions. The stellate mesopore silica nanoparticles with poly(N ‐isopropylacrylamide) grafted inside the mesopores were loaded with one compound (Nile red) and used as Pickering emulsifiers to stabilize oil‐in‐water droplets. Upon UV irradiation, pH‐responsive monomers were polymerized in the presence of 5(6)‐carboxyfluorescein diacetate (CFDA) to form hybrid colloidal microcontainers. The release of Nile red and CFDA could be selectively activated by changing the temperature or pH value.     

Clay-based colloidosomes

Poly(ethylene imine) (PEI) has been adsorbed onto the surface of Laponite clay nanoparticles from aqueous solution at pH 9 in order to produce an efficient hybrid Pickering emulsifier. This facile protocol allows formation of stable sunflower oil-in-water Pickering emulsions via homogenization at 12,000 rpm for 2 min at 20 °C. The effect of varying the extent of PEI adsorption on the Pickering emulsifier performance of the surface-modified Laponite is investigated for five oils of varying polarity using aqueous electrophoresis, thermogravimetric analysis, and laser diffraction studies. A minimum volume-average emulsion droplet diameter of around 60 μm was achieved at a Laponite concentration of 0.50% by mass when utilizing a PEI/Laponite mass ratio of 0.50. Such emulsions proved to be very stable toward droplet coalescence over time scales of months, although creaming is observed on standing within days due to the relatively large droplet size. These conditions correspond to submonolayer coverage of the Laponite particles by the PEI, which ensures that there is little or no excess PEI remaining in the aqueous continuous phase. This situation is confirmed by visual inspection of the underlying aqueous phase of the creamed emulsion when using fluorescently labeled PEI. These Pickering emulsions are readily converted into novel clay-based colloidosomes via reaction of the primary and/or secondary amine groups on the PEI chains adsorbed at the Laponite surface with either oil-soluble poly(propylene glycol) diglycidyl ether or water-soluble poly(ethylene glycol) diglycidyl ether cross-linkers. These colloidosomes were sufficiently robust to survive the removal of the internal oil phase after washing with excess alcohol, as judged by both optical and fluorescence microscopy. However, dye release studies conducted with clay-based colloidosomes suggest that these microcapsules are highly permeable and hence do not provide an effective barrier for retarding the release of small molecules.     

Ca2+ Responsive Microgel-Stabilized Pickering Emulsions

As an ionic cross-linker that can change the size of poly(N-isopropylacrylamide-co-acrylic acid) microgel, Ca²⁺ is applied as a trigger to demulsify microgel-stabilized oil/water Pickering emulsions. The influence of Ca²⁺ induced intra-particle ionic cross-linking and inter-particle aggregation on the stability of microgel-stablized “Pickering” emulsion is described. At low and mediate concentration of Ca²⁺, ionic cross-linking can change the internal elasticity of the microgel, and cause the coarsening of the oil droplets. At high concentration of Ca²⁺, microgels flocculate due to the salt out effect and the emulsion is destabilized. This work provide a facile method to control the stability of the Pickering emulsions at ambient condition.