Antifouling properties of materials play crucial roles in many important applications such as biomedical implants, marine antifouling coatings, biosensing, and membranes for separation. Poly(ethylene glycol) (or PEG) containing polymers and zwitterionic polymers have been shown to be excellent antifouling materials. It is believed that their outstanding antifouling activity comes from their strong surface hydration. On the other hand, it is difficult to develop underwater glues, although adhesives with strong adhesion in a dry environment are widely available. This is related to dehydration, which is important for adhesion for many cases while water is the enemy of adhesion. In this research, we applied sum frequency generation (SFG) vibrational spectroscopy to investigate buried interfaces between mussel adhesive plaques and a variety of materials including antifouling polymers and control samples, supplemented by studies on marine animal (mussel) behavior and adhesion measurements. It was found that PEG containing polymers and zwitterionic polymers have very strong surface hydration in an aqueous environment, which is the key for their excellent antifouling performance. Because of the strong surface hydration, mussels do not settle on these surfaces even after binding to the surfaces with rubber bands. For control samples, SFG results indicate that their surface hydration is much weaker, and therefore mussels can generate adhesives to displace water to cause dehydration at the interface. Because of the dehydration, mussels can foul on the surfaces of these control materials. Our experiments also showed that if mussels were forced to deposit adhesives onto the PEG containing polymers and zwitterionic polymers, interfacial dehydration did not occur. However, even with the strong interfacial hydration, strong adhesion between mussel adhesives and antifouling polymer surfaces was detected, showing that under certain circumstances, interfacial water could enhance the interfacial bio-adhesion.Antifouling properties of materials play crucial roles in many important applications such as biomedical implants, marine antifouling coatings, biosensing, and membranes for separation.相似文献
Marine organisms such as plants, algae or small animals can adhere to surfaces of materials that are submerged in ocean. The accumulation of these organisms on surfaces is a marine biofouling process that has considerable adverse effects. Marine biofouling on ship hulls can cause severe fuel consumption increase. Investigations on antifouling polymers are therefore becoming important research topics for marine vessel operations. Antifouling polymers can be applied as coating layers on the ship hull, protecting it against the settlement and growth of sea organisms. Polyethylene glycol (PEG) is a hydrophilic polymer that can effectively resist the accumulation of marine organisms. PEG-based antifouling coatings have therefore been extensively researched and developed. However, the inferior stability of PEG makes it subject to degradation, rendering it ineffective for long-term services. Zwitterionic polymers have also emerged as promising antifouling materials in recent years. These polymers consist of both positively charged and negatively charged functional groups. Various zwitterionic polymers have been demonstrated to exhibit exceptional antifouling properties. Previously, surface characterizations of zwitterionic polymers have revealed that strong surface hydration is critical for their antifouling properties. In addition to these hydrophilic polymers, amphiphilic materials have also been developed as potential antifouling coatings. Both hydrophobic and hydrophilic functional groups are incorporated into the backbones or sidechains of these polymers. It has been demonstrated that the antifouling performance can be enhanced by precisely controlling the sequence of the hydrophobic-hydrophilic functionalities. Since biofouling generally occurs at the outer surface of the coatings, the antifouling properties of these coatings are closely related to their surface characteristics in water. Therefore, understanding of the surface molecular structures of antifouling materials is imperative for their future developments. In this review, we will summarize our recent advancements of antifouling material surface analysis using sum frequency generation (SFG) vibrational spectroscopy. SFG is a surface-sensitive technique which can provide molecular information of water and polymer structures at interfaces in situ in real time. The antifouling polymers we will review include zwitterionic polymer brushes, mixed charged polymers, and amphiphilic polypeptoids. Interfacial hydration studies of these polymers by SFG will be presented. The salt effect on antifouling polymer surface hydration will also be discussed. In addition, the interactions between antifouling materials and protein molecules as well as algae will be reviewed. The above research clearly established strong correlations between strong surface hydration and good antifouling properties. It also demonstrated that SFG is a powerful technique to provide molecular level understanding of polymer antifouling mechanisms. 相似文献
Conjugated polymers are essential for solution‐processable organic opto‐electronic devices. In contrast to the great efforts on developing new conjugated polymer backbones, research on developing side chains is rare. Herein, we report branched oligo(ethylene glycol) (OEG) as side chains of conjugated polymers. Compared with typical alkyl side chains, branched OEG side chains endowed the resulting conjugated polymers with a smaller π‐π stacking distance, higher hole mobility, smaller optical band gap, higher dielectric constant, and larger surface energy. Moreover, the conjugated polymers with branched OEG side chains exhibited outstanding photovoltaic performance in polymer solar cells. A power conversion efficiency of 5.37 % with near‐infrared photoresponse was demonstrated and the device performance could be insensitive to the active layer thickness. 相似文献
A kind of fluorescent/phosphorescent dual-emissive conjugated polyelectrolyte has been prepared by introducing phosphorescent platinum(ii) porphyrin (O2-sensitive) into a fluorene-based conjugated polyelectrolyte (O2-insensitive), which can form ultrasmall conjugated polymer dots (FP-Pdots) in the phosphate buffer solution (PBS) via self-assembly caused by their amphiphilic structures with hydrophobic backbones and hydrophilic side chains. These FP-Pdots can exhibit an excellent ratiometric luminescence response to O2 content with high reliability and full reversibility for measuring oxygen levels, and the excellent intracellular ratiometric O2 sensing properties of the FP-Pdots nanoprobe have also been confirmed by the evident change in the Ired/Iblue ratio values in living cells cultured at different O2 concentrations. To confirm the reliability of the O2 sensing measurements of the FP-Pdots nanoprobe, O2 quenching experiments based on lifetime measurements of phosphorescence from Pt(ii) porphyrin moieties have also been carried out. Utilizing the sensitivity of the long phosphorescence lifetime from Pt(ii) porphyrins to oxygen, the FP-Pdots have been successfully applied in time-resolved luminescence imaging of intracellular O2 levels, including photoluminescence lifetime imaging and time-gated luminescence imaging, which will evidently improve the sensing sensitivity and reliability. Finally, in vivo oxygen sensing experiments were successfully performed by luminescence imaging of tumor hypoxia in nude mice. 相似文献
Three stable polyradicals with large π-conjugated planar phenalenyl (PLY) radical units as side chain were synthesized. Due to the different conjugated backbones and the interactions between main chains and side chains, these polyradicals and their corresponding precursor polymers presented diverse optical and electrical properties, which were confirmed by UV–vis, fluorescence and CV detections. Besides, they showed excellent solubility in common organic solvents and good stability in the air. Considering their special characteristics, we have fabricated photovoltaic (PV) devices using these polyradicals or polymers as donor material and PCBM as acceptor material. The significant PV performance improvement was observed using a radical-based active layer in the PV devices. 相似文献
A new series of donor–acceptor co‐polymers based on benzodithiophene and quinoxaline with various side chains have been developed for polymer solar cells. The effect of the degree of branching and dimensionality of the side chains were systematically investigated on the thermal stability, optical absorption, energy levels, molecular packing, and photovoltaic performance of the resulting co‐polymers. The results indicated that the linear and 2D conjugated side chains improved the thermal stabilities and optical absorptions. The introduction of alkylthienyl side chains could efficiently lower the energy levels compared with the alkoxyl‐substituted analogues, and the branched alkoxyl side chains could deepen the HOMO levels relative to the linear alkoxyl chains. The branched alkoxyl groups induced better lamellar‐like ordering, but poorer face‐to‐face packing behavior. The 2D conjugated side chains had a negative influence on the crystalline properties of the co‐polymers. The performance of the devices indicated that the branched alkoxyl side chains improved the Voc, but decreased the Jsc and fill factor (FF). However, the 2D conjugated side chains would increase the Voc, Jsc, and FF simultaneously. For the first time, our work provides insight into molecular design strategies through side‐chain engineering to achieve efficient polymer solar cells by considering both the degree of branching and dimensionality. 相似文献
A series of conjugated polymers based on PFS derivatives with π-conjugated 5-(9H-fluoren-2-yl)-2,2′-bithiophene(fluorene-alt-bithiophene) backbones, namely PFS-3C, PFS-4C and PFS-6C, were synthesized for their use as the anode interfacial layers(AILs) in the efficient fullerene-free polymer solar cells(PSCs). Alkyl sulfonate pendants with different lengths of alkyl side chains were introduced in the three polymers in order to investigate the effect of the alkyl chain length on the anode modification. The obtained three polymers exhibited similar absorption bands and energy levels, indicating that changing the length of the alkyl side chains did not affect the optoelectronic properties of the conjugated polymers. Based on the PBDB-T:ITIC active layer, we fabricated the fullerene-free PSCs using the three polymers as the AILs. The superior performance of the fullerene-free PSC device was achieved when PFS-4C was used as the AIL, showing a power conversion efficiency(PCE) of 10.54%. The high performance of the PFS-4C-modified device could be ascribed to the high transmittance, suitable work-function(WF) and smooth surface of PFS-4C. To the best of our knowledge, the PCE obtained in the PFS-4C-modified device is among the highest PCE values in the fullerene-free PSCs at present. These results demonstrate that the PFS derivatives are promising candidates in serving as the AIL materials for high-performance fullerene-free PSCs. 相似文献
Conductive polymers such as poly(3,4-ethylenedioxythiophene) (PEDOT) are used in a wide range of applications as transparent electrodes, hole injecting layers or thermoelectric materials for room-temperature applications. However, progress is needed to enhance the electrical conductivities of the materials and to provide understanding about their structure–transport relationships. This work presents the synthesis of highly conductive PEDOT-based polymers using iron(iii) trifluoromethanesulfonate as oxidant for the first time. The metallic behaviour of the polymer is revealed by conductivity monitoring from 3 to 300 K. The electrical conductivity is further improved (to 2273 S cm–1) using acids, leading to a positive temperature coefficient of resistivity at an unprecedented 45.5% oxidation state. X-ray photoemission spectroscopy (XPS) and time of flight-secondary ion mass spectrometry (ToF-SIMS) analyses demonstrate a complete replacement of the trifluoromethanesulfonate anions by hydrogen sulphate counter ions. This substitution results in an increased concentration of charge carriers (measured in organic electrochemical transistors) along with an enhancement of the mean size of crystalline domains, highlighted by small and wide angle X-ray scattering (SAXS/WAXS), which explains the 80% increase of electrical conductivity. 相似文献
In recent years, the use of organic materials to infer conductivity in biomedical devices has received increasing attention. Typical inorganic semiconductors and conductors are rigid and expensive, usually require multiple processing steps and are unsuitable for biomedical applications. Electrochemically or chemically doped conjugated polymers help to overcome these problems due to their stability, low cost, light weight and excellent electrical and optical properties. The conducting polymer poly(3,4-ethylenedioxythiophene): polystyrene sulfonate (PEDOT:PSS) is the material of choice for biomedical applications as it is water soluble, however, there are growing concerns around its stabilizer, PSS, due to its release of acidic products upon degradation in-vivo. Here, we report the successful synthesis of PEDOT nanoparticles using hyaluronic acid (HA) as a stabilizer via an oxidative miniemulsion polymerisation technique. This improves the bioactivity and hydrophilicity of nanoparticles. The effect of varying amounts of HA and different molar ratios of EDOT:TOS has been studied and their role in the conductive and morphological properties of final nanoparticles has been fully elucidated. Furthermore, bioactivity and biocompatibility of the nanoparticles are demonstrated for customizable in vivo applications. Nanoparticles were found to have a conductivity up to 10 times greater than pristine PEDOT:PSS with increased addition of oxidant. The proposed easy-to-manufacture approach, along with the highlighted superior properties, expands the potential of conductive polymers in future customizable biological applications such as tissue scaffolds, nerve conduits and cardiac patches and represents a real breakthrough from the current state of the art. 相似文献
A new class of segmented non-conjugated dopable polymers, built up from short conjugated blocks connected with flexible chains (spacers), has been proposed. After the redox reaction of doping these polymers exhibit properties similar to those of the fully conjugated polymers and increase considerably their electrical conductivity. A solid state polymer effect has been observed. It has been found that the conjugated building units (biphenyl, diphenyl ether and 1,3,4-oxadiazole) do not interact with the dopant when included in a low molecular weight substance. When these units are incorporated in a polymer chain they change their reactivity and the polymer can be doped. The doping process takes place only when the polymer is in the solid state and the nature of this phase is of considerable importance. The phenomenon observed, i.e. doping of non-conjugated polymers with segmented structure could be explained with a favourable arrangement of the conjugated blocks in the solid phase, leading to enhanced π-π - interaction (equivalent to extended conjugation). By the collective interaction of several conjugated blocks with the dopant the polymer is partially oxidized and charge carriers are formed. The result is enhanced electrical conductivity. 相似文献
A facile strategy for the synthesis of conjugated polyelectrolyte brushes grafted from a conductive surface is presented. Such brushes form a platform of molecular wires oriented perpendicularly to the surface, enabling efficient directional transport of charge carriers. As the synthesis of conjugated polymer brushes using chain-growth polymerization via a direct “grafting from” approach is very challenging, we developed a self-templating surface-initiated method. It is based on the formation of multimonomer template chains in the first surface-initiated polymerization step, followed by the second polymerization leading to conjugated chains in an overall ladder-like architecture. This strategy exploits the extended conformation of the surface-grafted brushes, thereby enabling alignment of the pendant polymerizable groups along the template chains. We synthesized a new bifunctional monomer and used the developed approach to obtain quaternized poly(ethynylpyridine) chains on a conductive indium tin oxide surface. A catalyst-free quaternization polymerization was for the first time used here for surface grafting. The presence of charged groups makes the obtained brushes both ionically and electronically conductive. After doping with iodine, the brushes exhibited electronic conductivity, in the direction perpendicular to the surface, as high as 10–1–100 S m–1. Tunneling AFM was used for mapping the surface conductivity and measuring the conductivity in the spectroscopic mode. The proposed synthetic strategy is very versatile as a variety of monomers with pendant polymerizable groups and various polymerization techniques may be applied, leading to platforms of molecular wires with the desired characteristics. 相似文献
Side chains play a considerable role not only in improving the solubility of polymers for solution‐processed device fabrication, but also in affecting the molecular packing, electron affinity and thus the device performance. In particular, electron‐donating side chains show unique properties when employed to tune the electronic character of conjugated polymers in many cases. Therefore, rational electron‐donating side chain engineering can improve the photovoltaic properties of the resulting polymer donors to some extent. Here, a survey of some representative examples which use electron‐donating alkylthio and alkoxy side chains in conjugated organic polymers for polymer solar cell applications will be presented. It is envisioned that an analysis of the effect of such electron‐donating side chains in polymer donors would contribute to a better understanding of this kind of side chain behavior in solution‐processed conjugated organic polymers for polymer solar cells.
We develop a new process for the preparation of synergistic antifouling functional coatings on gold surfaces via a “grafting to” approach. The strategy includes a synthetic step of polymer brushes that consist of poly (ethylene glycol) (PEG) and zwitterionic side chains via a typical reversible-addition fragmentation chain transfer (RAFT) polymerization process, and a subsequent deposition of the polymer brushes onto a gold substrate. The presence of PEG and zwitterion chains on these polymer brush-coated gold surfaces has been proved to have a synergistic effect on the final antifouling property of the coating. PEG chains lower the electrostatic repulsion between zwitterionic polymer chains and increase their graft density on gold surfaces, while zwitterionic polymer effectively improves the antifouling property that is offered by PEG chains alone. Protein adsorption and cell attachment assays tests are conducted to confirm that this copolymer layer on gold surface has a pronounced resistance against proteins such as Bovine serum albumin and Lysozyme. Importantly, the antifouling property can be systematically adjusted by varying the molar ratio of PEG to zwitterionic chains in the final coating copolymer. 相似文献