乙丙共聚物熔融接枝甲基丙烯酸环氧丙酯

乙丙共聚物熔融接枝甲基丙烯酸环氧丙酯张晓民，尹志辉，殷敬华（中国科学院长春应用化学研究所高分子物理开放实验室长春１３００２２）关键词乙丙共聚物，甲基丙烯酸环氧丙酯，接枝共聚接枝共聚物可作为不相容共混体系的增容剂［１，２］，反应加工法制备乙丙共聚物（Ｅ...     

丙烯酸酯共聚物乳液自交联反应的研究

本文研究了含环氧基的丙烯酸酯四元共聚物乳液交联后的溶胀度、自交联反应及动力学.结果表明:交联共聚物的溶胀度Q随甲基丙烯酸环氧丙酯单体含量的增加而降低,共聚物在受热的情况下,环氧基因在羧基的作用下开环而发生交联反应,产生网状结构.     

高效凝胶色谱研究甲基丙烯酸环氧丙酯封端聚苯乙烯大分子单体的活性

合成大分子单体的封端剂一般是含卤素原子的烯烃化合物、丙烯酰卤化合物、卤代环氧化合物及不饱和酸酐等四大类。甲基丙烯酸环氧丙酯(GMA)作为聚苯乙烯(PS)活性阴离子封端剂合成甲基丙烯酸环氧丙酯封端聚苯乙烯大分子单体(PS-GMA)是     

苯乙烯和甲基丙烯酸环氧丙酯共聚物单分散粒子的合成

分散聚合;苯乙烯和甲基丙烯酸环氧丙酯共聚物单分散粒子的合成     

甲基丙烯酸-丙烯酸丁酯-甲基丙烯酸环氧丙酯三元共聚物的合成与表征

以甲基丙烯酸(MAA),丙烯酸丁酯(BA)和甲基丙烯酸环氧丙酯(GMA)为原料,偶氮二异丁腈(AIBN)为引发剂,十二硫醇(DT)为链转移剂,通过溶液聚合法合成了甲基丙烯酸-丙烯酸丁酯-甲基丙烯酸环氧丙酯(MAA-BA-GMA)三元共聚物,其结构和性能经1H NMR,13C NMR,IR,GPC,DSC和TGA表征.通过调节AIBN和DT的用量可控制MAA-BA-GMA的分子量在7 900～23 700.热分析数据结果表明,MAA-BA-GMA具有良好的柔性;分解温度为429℃～440℃.     

甲基丙烯酸环氧丙酯共聚物的研究

含有甲基丙烯酸环氧丙酯的聚合物是热活性高分子,它们可以被用来合成体型共聚物或接枝共聚物。 当甲基丙烯酸环氧丙酯、甲基丙烯酸甲酯、和甲基丙烯酸三种单体一起进行共聚合时,首先得到一种綫型的共聚物。这种共聚物经过在120℃以上热处理,就转化成一种透明的体型的共聚物,红外光谱的研究证示,在热处理时分子链间的环氧基和羧基起了反应,交联的结果使共聚物的玻璃化温度由110℃左右提高到150℃左右。 把甲基丙磷酸环氧丙酯和甲基丙烯酸甲酯的共聚物与消去末端氨基的聚己内酰胺共溶于热的苯甲醇并150℃加热,可以得到一种接枝共聚物。这种接枝共聚物一旦析出并干燥以后,在常温下不溶于包括苯甲醇、间甲苯酚在内的大多数溶剂,但却易溶于极性较强的溶剂如98％的甲酸。这个反常的表现被认为是由于分子链间氢键作用所引起的。 作为骨干的甲基丙烯酸环氧丙酯和甲基丙烯酸甲酯共聚物及其聚己内酰胺的接枝共聚物在苯甲醇及在间甲苯酚中作了溶液粘度测定,在间甲苯酚溶液内,由于接枝,Huggins常数k′值增加了;但在苯甲醇溶液内,k′值却无甚变化。这说明由于主链和枝链化学性貭的不同,溶剂对它们的作用不一样,接枝对溶液粘度的影响不能和普通的枝化高分子等 量齐观。     

x－甲基丙烯酸2，3－环氧丙基酯与α－甲基丙烯酸甲酯嵌段共聚物的合成与鉴定

α－甲基丙烯酸２，３－环氧丙基酯与■－甲基丙烯酸甲酯嵌段共聚物的合成与鉴定张洪敏侯元雪程■（北京化工大学高分子系北京１０００２９）关键词■－甲基丙烯酸２，３－环氧丙基酯，甲基丙烯酸甲酯，嵌段共聚物■－甲基丙烯酸２，３－环氧丙基酯（ＥＰＭＡ）含有两个可...     

硅胶涂敷正相色谱填料的制备及应用

在大孔硅胶表面键合乙烯基硅烷化试剂,然后与甲基丙烯酸环氧丙酯、甲基丙烯酸乙二醇双酯共聚,制得聚合物涂敷硅胶,其表面经一步水解即可得到正相高效液相色谱填料,考察了该填料对苯的衍生物及吡啶等有机化合物的分离情况.实验结果表明,硅胶涂敷正相色谱柱对中性、酸性和碱性化合物均具有良好的色谱分离性能.     

甲基丙烯酸羟乙酯改性水性聚氨酯乳液的制备及性能

采用种子溶胀乳液聚合法,以水性聚氨酯为种子,甲基丙烯酸羟乙酯、甲基丙烯酸甲酯和丙烯酸丁酯为单体制备水性聚氨酯丙烯酸酯复合乳液,考察了甲基丙烯酸羟乙酯含量对复合乳液的T型剥离、胶膜的硬度、耐水性和力学性能的影响。结果表明,随着甲基丙烯酸羟乙酯含量的增加,复合乳液的T型剥离强度、胶膜的硬度和拉伸强度增大,胶膜的耐水性先增大后减小,断裂伸长率有所降低,适宜的甲基丙烯酸羟乙酯用量为3%。     

高分子微球偶联固定培美曲塞二钠

在无皂乳液聚合制备表面带环氧基的聚(苯乙烯-甲基丙烯酸环氧丙酯)(PSG)乳液微球的基础上,采用1,6-己二胺对PSG微球进行表面修饰,获得了氨基封端、表面清洁的PSG-1,6-己二胺(PSGN)微球。通过PSGN微球表面的端氨基反应性偶联固定培美曲塞二钠药物分子,考察了药物分子偶联固定反应的影响因素。结果表明:培美曲塞二钠药物在PSGN微球表面的固定接枝量主要取决于PSGN微球的粒径大小和表面活泼端氨基的质量浓度及分布。     

Synthesis and surface properties of self-crosslinking core–shell acrylic copolymer emulsions containing fluorine/silicone in the shell

Stable emulsions of a core–shell acrylic copolymer (non-crosslinkable V0, and crosslinkable V2, V4, V6, and V8, where the numbers indicate the wt% of crosslinking agent based on the total acrylate monomer content) containing butyl acrylate (BA, 45 wt%), glycidyl methacrylate (GMA, 45 wt%), heptadecafluorodecyl methacrylate (PFA, 10 wt%), and various contents of crosslinking agent (vinyltriethoxysilane, VTES) were synthesized using a three-stage seeded emulsion polymerization process with a small amount of surfactant. The average particle size and viscosity of emulsions increased significantly with increasing VTES content. This study examined the effects of the VTES content on the surface/mechanical properties of self-crosslinked copolymer film samples containing a fixed acrylate monomer content to find the optimum VTES content. XPS showed that the film–air surface of the copolymer samples had a higher fluorine/silicone content than the film–dish interface. The tensile strength/modulus, thermal stability, and two Tgs (α and β Tgs) of the film samples increased significantly with increasing VTES content. The contact angle of the film samples increased with increasing VTES content up to approximately 6 wt%, and then decreased slightly. The optimum VTES content was approximately 6 wt% based on the total acrylate monomer content to obtain a high water/oil repellent coating material (V6) with the highest water/methylene iodide-contact angles (118.2°/81.8°) and lowest surface energy (18.4 mN/m).     

反应性复合乳液的合成、表征及其交联反应

利用种子半连续乳液聚合方法合成了核层或壳层带有环氧基以及壳层带有羧基的3种不同核/壳结构的乳胶粒子,通过物理共混带环氧基和羧基的乳胶粒子,得到了两种反应性复合乳液.利用透射电镜和激光动态光散射对乳胶粒子进行了表征,其粒径分布较窄,粒径分布的多分散系数为0.062,平均粒径约76 nm,乳胶粒子具有明显的核/壳结构.通过胶膜的凝胶率和膨胀率的测定和红外光谱分析对反应性复合乳液中乳胶粒子的扩散及交联反应进行了研究,并探讨了不同核壳结构复合乳液对涂膜机械性能的影响.研究表明,当反应性复合乳液中的环氧基和羧基分别分布在乳胶粒子的核层和壳层时,有利于聚合物分子链的充分扩散和化学交联反应的进行,从而提高涂膜的物理化学性能,当甲基丙烯酸缩水甘油酯(GMA)含量为10 wt%时,涂膜的拉伸强度达20.3 MPa.     

Synthesis and characterization of epoxy-functional polystyrene particles

Colloidal polystyrene particles with surface epoxy groups have been synthesized through surfactant-free emulsion copolymerization of styrene with glycidyl methacrylate; and through copolymerization of glycidyl methacrylate (GMA) and methyl methacrylate as shells around existing polystyrene seed particles. We developed two titration methods to quantify the number of epoxy groups that survived the polymerization processes. The styrene-GMA copolymer particles were judged to be unsatisfactory as model colloidal materials due to their size polydispersity and unknown internal distribution of epoxy groups. The core-shell particles had high epoxy surface densities with at least 60% of the initial epoxy groups surviving the synthesis process. Transmission electron microscopy shows that the thickness of the epoxy-rich shell is less than expected based on the volume of monomers added, suggesting that some of the monomer forms water-soluble oligomers. Photon correlation spectroscopy measurements imply that the shell is swollen with water and consists of polymer configurations which extend out into solution. The morphological details vary consistently with the GMA content, and hence the hydrophilicity, of the shell polymer. © 1995 John Wiley & Sons, Inc.     

Improving Damping Properties and Thermal Stability of Epoxy/Polyurethane Grafted Copolymer by Adding Glycidyl POSS

Modified castor oil-based epoxy resin (EP)/polyurethane (PU) grafted copolymer by glycidyl polyhedral oligomeric silsesquioxane (glycidyl POSS) was synthesized. The damping properties, thermal stability, mechanical properties and morphology of the grafted copolymer modified by glycidyl POSS were studied systematically. The results revealed that the incorporation of glycidyl POSS improved the damping performance evidently and broadened damping temperature range, especially when the glycidyl POSS content was0.2%–1%. At the same time, there was a slight increase in thermal stability with the increase of POSS content. The tensile properties changed with the change of the copolymer's Tg, decreased at low POSS contents and increased at high POSS contents. This modified copolymer has the potential to be used as film damping material or constrained damping layer.     

Toughening of poly(2,6-dimethyl-1,4-phenylene oxide)/nylon 6 alloys with functionalized elastomers via reactive compatibilization: morphology, mechanical properties, and rheology

Blends of poly(2,6-dimethyl-1,4-phenylene oxide)/nylon 6 alloys based on ethylene-propylene-diene elastomer (EPDM) grafted with maleic anhydride (MA) (EPDM-g-MA), EPDM grafted with glycidyl methacrylate (EPDM-g-GMA), and styrene-ethylene-butadiene-styrene block copolymer grafted with MA (SEBS-g-MA) were prepared via melt extruction, and morphology, mechanical properties, and rheology were studied. The compatibilizing effects of functionalized elastomers on the PPO/nylon 6 alloys were proved by DSC analysis and confirmed by the significant improvement in the notched Izod impact strength. Toughening was resulted from the smaller particle size and finer dispersion of EPDM in the PPO/nylon 6 matrix as well as a novel network structure of SEBS-g-MA domain in matrix. The notched Izod impact strength of the blends exhibited an optimum value when the extent of MA or GMA graft ratio of EPDM varied, which was an order of magnitude higher than the non-toughened alloys. The morphology revealed that the size of EPDM particles decreased with an increase in graft ratio of MA or GMA onto EPDM. Rheology investigation indicated that the MA or GMA moieties on EPDM reacted with the amine groups of nylon 6, which increased the molecular weight and the degree of branching, and thus resulted in an increase in the viscosity of the blends. This proved the reactive compatibilization between functionalized EPDM and PPO/nylon 6 matrix.     

Poly(N-vinylcaprolactam-co-glycidyl methacrylate) aqueous microgels labeled with fluorescent LaF3:Eu nanoparticles

We describe the synthesis and properties of functional microgel particles based on poly(N-vinylcaprolactam-co-glycidyl methacrylate) (PVCL/PGMA) copolymer. A series of colloidally stable microgel particles with a range of glycidyl methacrylate content were prepared by surfactant-free heterophase polymerization in water. The microgel particles obtained had hydrodynamic radii between 250 and 350 nm and were fairly monodisperse in size; however, a broadening of the particle size distribution was observed for samples with a low GMA content. The PVCL/PGMA microgel particles exhibit thermally responsive reversible changes in diameter in water, and the swelling degree increased with the PVCL fraction in the copolymer structure. These microgels were then modified with photoluminescent europium-doped lanthanum fluoride nanoparticles (LaF3:Eu-AEP) through reaction of the 2-aminoethyl phosphate surface ligands with epoxy groups present in the microgel. These hybrid microgels were colloidally stable and thermally responsive in aqueous solution.     

Novel functional copolymers based on glycidyl methacrylate: Synthesis,characterization, and polymerization kinetics

A new methacrylate monomer 2-(4-nitrophenyl)-2-oxoethyl-2-methacrylate (NFM) was synthesized and its radical copolymerization with glycidyl methacrylate (GMA) was studied in 1,4-dioxane solution at 65°C using 2,2′-azobisisobutyronitrile as an initiator. The synthesized monomer and copolymers were characterized by FTIR, ¹H and ¹³C-NMR spectroscopy. The analysis of reactivity ratios revealed that NFM is less reactive than GMA, and copolymers formed are statistically in nature. Thermogravimetric analysis of the polymers reveals that the thermal stability of the copolymers increases with an increasing in the mole fraction of NFM in the copolymers. Glass transition temperatures of the copolymers decreased with an increasing of NFM molar fraction in copolymers. In addition, according to the results obtained from the contact angle and zeta potential measurements the hydrophobic character of the polymer decreases (it means surface free energy increases) and its zeta potential becomes more negative with increase of NFM ratio in the copolymer. Polymers with carbonyl functional groups have been particularly interesting because of their use as photoresists.     

EPM-g-GMA接枝率的测定及其增韧PBT的力学性能和形态结构研究

在同向双螺杆挤出机中通过熔融接枝反应制备了EPM g GMA ,将其与PBT在转矩流变仪中熔融共混可以获得增韧的PBT工程塑料 .实验中EPM g GMA接枝率的测定采用红外工作曲线法 ,选用CCl4 做溶剂以避免溶剂对样品吸收峰的干扰 .随着EPM g GMA接枝率的增加 ,PBT EPM g GMA的缺口冲击强度相应提高 ,共混物中EPM g GMA的粒径尺寸减小 ,当EPM g GMA的接枝率为 4 7mL 1 0 0gEPM时 ,EPM g GMA的粒径尺寸可达 0 5 μm ,PBT EPM g GMA的缺口冲击强度达到 5 1 6kJ m2 ,是纯PBT的 3 1倍     

Preparation of fully cross‐linked CNBR/PP‐g‐GMA and CNBR/PP/PP‐g‐GMA thermoplastic elastomers and their morphology,structure and properties

Binary CNBR/PP‐g‐GMA and ternary CNBR/PP/PP‐g‐GMA thermoplastic elastomers were prepared by reactive blending carboxy nitrile rubber (CNBR) powder with nanometer dimension and polypropylene functionalized with glycidyl methacrylate (PP‐g‐GMA). Morphology observation by using an atomic force microscope (AFM) and TEM revealed that the size of CNBR dispersed phase in CNBR/PP‐g‐GMA binary blends was much smaller than that of the corresponding CNBR/PP binary blends. Thermal behavior of CNBR/PP‐g‐GMA and CNBR/PP blends was studied by DSC. Comparing with the plain PP‐g‐GMA, T_c of PP‐g‐GMA in CNBR/PP‐g‐GMA blends increased about 10 °C. Both thermodynamic and kinetic effects would influence the crystallization behavior of PP‐g‐GMA in CNBR/PP‐g‐GMA blends. At a fixed content of CNBR, the apparent viscosity of the blending system increased with increasing the content of PP‐g‐GMA. FTIR spectrum verified that the improvement of miscibility of CNBR and PP‐g‐GMA was originated from the reaction between carboxy end groups of CNBR and epoxy groups of GMA grafted onto PP molecular chains. Comparing with CNBR/PP blends, the tensile strength, stress at 100% strain, and elongation at break of CNBR/PP‐g‐GMA blends were greatly improved. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1042–1052, 2004