六方氮化硼催化的乙烷丙烷共脱氢:一种C–H键活化和机理研究的有效手段（英文）

乙烯、丙烯等低碳烯烃是化学工业重要的原料.目前工业化的低碳烷烃脱氢制烯烃技术均为直接脱氢技术,例如基于Pt-Sn催化剂的Oleflex工艺以及基于CrO_x的Catofin工艺.相对于直接脱氢,氧化脱氢具有不受热力学限制和避免积碳生成的优点.然而,传统的氧化脱氢催化剂(例如VO_x)难以抑制深度氧化副反应的发生,因而使目标产物烯烃的收率受到抑制.近年来,六方氮化硼(h-BN)对低碳烷烃氧化脱氢过程表现出的高催化活性以及高烯烃选择性,受到了国内外研究者的广泛关注.同时, h-BN在烷烃反应级数以及表观活化能等方面表现出明显不同于其他烷烃脱氢催化剂的性质.研究表明,气相自由基反应对h-BN的催化活性具有重要贡献.但是,烷烃表观反应级数为2这一现象始终没有得到较好的解释.本文针对该问题展开了探索.本文以乙烷和丙烷的混合烷烃作为反应物,研究h-BN催化的氧化脱氢过程.结果表明,丙烷的存在可以显著促进乙烷脱氢转化的速率,在580oC下,少量丙烷的引入可以使乙烷的转化率提高47%.同时,固定乙烷分压不变时,乙烷氧化脱氢速率对丙烷分压的表观反应级数为1.这说明...     

负载PtSn金属助剂的镁铝水滑石上的丙烷脱氢反应研究

我们研究了以镁铝水滑石作为载体,利用水滑石层间阴离子的可交换性,负载活性金属铂和锡的丙烷脱氢反应.在镁铝水滑石载体中加入Ga能够影响丙烷脱氢活性,当镓的含量为1%时催化剂丙烷脱氢反应活性最高,反应初始时,丙烷转化率为46.5%,反应2 h后,丙烷转化率仍有37.5%.当以Mg(Ga)(Al)O-1%为载体时,考察了不同H_2/C_3H_8摩尔比对丙烷脱氢活性的影响,结果表明当H_2/C_3H_8摩尔比为0.5∶1时,丙烷脱氢反应具有最佳的反应活性,即当在原料气中加入H_2时,能够使得丙烷脱氢的转化率大幅度提升,且选择性也有所提升.烷烃脱氢是一个吸热反应,同时考察了温度对烷烃脱氢反应性能影响,结果表明温度越高,丙烷脱氢反应具有更高的转化率.对催化剂进行长时间寿命实验考察,发现当反应经过40 h后,丙烷的转化率仍有23.5%,说明Pt Sn-Mg(Ga)(Al)O-1%催化剂具有较好的稳定性.     

氮化硼催化低碳烷烃氧化脱氢的活性起源探讨（英文）

页岩气的急速开采推动了以天然气替代石油的资源革命.除主组分甲烷外,天然气、页岩气中还包含大量乙烷、丙烷等低碳烷烃资源,将这些储量丰富的碳资源直接转化为烯烃等基础化学品有望革新以原油为基础的化学工业.现有烷烃催化脱氢制烯烃工艺中,直接脱氢过程吸热、热力学受限,且存在催化剂迅速失活的难题;而氧化脱氢是放热过程、无平衡限制,也无积碳等引发催化剂失活的问题,有利于提高反应效率、降低能耗,代表了更为高效和经济的新路线.但作为一个热力学爬坡过程,目前金属氧化物催化剂上烯烃产物很容易深度氧化到CO_2,选择性仍有待提高.非金属氮化硼能够有效活化低碳烷烃中的C-H键,促进烷烃氧化脱氢,并能够有效抑制深度氧化产物的生成,解决低碳烷烃临氧脱氢过程中产物易深度氧化的固有难题.本文综述了近期氮化硼在乙烷、丙烷、丁烷等低碳烷烃氧化脱氢制烯烃反应中的研究进展.以丙烷氧化脱氢为例,通过比较文献报道的几种氮化硼材料的氧化脱氢性能,发现羟基化氮化硼显示了最高的烯烃选择性和时空收率,以20.6%的丙烷转化率为基准,烯烃选择性超过90%,而时空收率可达6.8 golefin gcat~(-1) h~(-1).在此基础上,本文重点讨论了对于氮化硼材料催化活性起源的认识.主要实验事实和结论包括:氮化硼自身几乎没有氧化脱氢活性,而在烷烃氧化脱氢反应条件下存在活性诱导期;活性诱导期伴随着氮化硼边沿氧官能团化过程;氮化硼边沿B-O官能团没有脱氢活性,而B-OH官能团参与了氧化脱氢过程,辅助分子氧引发低碳烷烃脱氢反应;分子氧在羟基氮化硼边沿解离活化,反应过程中与边沿结构氧存在动态交换;氮化硼边沿羟基化定向合成过程可显著增强氧化脱氢反应活性.氮化硼作为一类新型烷烃氧化脱氢催化剂,目前正处于研究的初始阶段.因此,本文最后总结了一些关于氮化硼烷烃脱氢催化体系仍需深入研究的科学问题.     

富氧条件下Cu/Al2O3催化剂上C3H6选择性还原NO的研究

以Cu/Al2O3为催化剂,对富氧条件下C3H6为还原剂选择性催化还原NO反应进行了研究.活性评价结果表明,与高活性的Ag/Al2O3催化剂相比,Cu/Al2O3催化剂选择性还原NO的活性较低,NO的最高转化率仅为40%.在所考察的温度范围(473～723K)内,红外谱图中不存在有机含氮化合物(R—ONO和R—NO2)的特征振动吸收峰.作为反应中间体—NCO的前驱体,有机含氮化合物在Cu/Al2O3催化剂表面难以生成是造成催化剂选择性还原NO活性低的直接原因.在Cu/Al2O3催化剂上,NO2吸附能够优先发生,并以NO3-物种的形式覆盖在大部分催化剂表面.动态原位红外光谱实验发现,这种NO3-表面物种与C3H6的反应性较差,使生成有机含氮化合物的关键反应难以发生,但此时的催化剂表面有利于C3H6和O2的完全氧化反应,这是导致Cu/Al2O3催化剂选择性较低的根本原因.     

氧渗透膜反应器的烷烃氧化脱氢

研究了乙烷和丙烷在催化膜反应器中的氧化脱氢反应．所用的膜材料为La2Ni0.9V0.1O4＋δ和Ba0.5Sr0.5Co0.8Fe0.2O3-δ．为了平衡氧气通量和额外的均匀气相反应,实验选择在中温段进行（550或者650℃）．实验结果表明膜的氧渗透通量和膜表面上主要激活烷烃的活性位在获得高的烷烃转化率过程中起决定性作用．乙烷和丙烷的氧化脱氢实验数据均符合Mars-van Krevelen机理,其中烷烃和膜表面的晶格氧反应产生相应的烯烃．同时证明了气相和膜表面的氧浓度是决定烯烃选择性的关键．     

MoO3和Nb2O5助剂对Pt/ZrO2催化剂上短链烷烃燃烧反应的不同促进作用

贵金属Pt催化剂具有高活性和热稳定性,广泛应用于催化挥发性有机物的完全氧化反应(燃烧反应).短链烷烃(甲烷、乙烷、丙烷等)化学性质稳定,是最难氧化的一类有机物,常用作考察燃烧反应催化剂性能的模型反应物.然而,目前报道的研究工作通常仅限于针对某一种烷烃底物的催化燃烧,系统考察催化剂以及助剂对不同短链烷烃的催化燃烧活性鲜有报道.在短链烷烃中,甲烷只有C–H键;而其它烷烃除了C–H键;还有C–C键.因此,研究催化剂对甲烷、乙烷和丙烷燃烧反应催化性能的差异性,对于认识催化剂上C–H键和C–C键的活化具有非常重要的意义.本文制备了MoO3或Nb2O5修饰的Pt/ZrO2催化剂并用于短链烷烃的燃烧反应.研究发现,MoO3助剂对甲烷燃烧有明显的抑制作用,但对乙烷,丙烷和正己烷燃烧反应具有促进作用,促进作用随着烷烃碳链的增长逐渐增加;Nb2O5助剂对甲烷、乙烷、丙烷和正己烷燃烧反应均具有促进作用,然而促进作用随着碳链的增长而逐渐减弱.MoO3和Nb2O5助剂的不同促进作用与助剂影响催化剂表面酸性以及Pt物种的氧化或还原态有关.NH3-TPD结果表明,MoO3助剂可以显著增加Pt/ZrO2催化剂表面强酸位点数量,而Nb2O5助剂可以显著增加Pt/ZrO2催化剂表面中强酸位点数量.HTEM结果表明,两种助剂的添加都不会明显改变Pt物种的颗粒尺寸.在Pt-Mo/ZrO2催化剂上,MoO3覆盖部分Pt物种形成丰富的Pt-MoO3界面,促进了金属Pt物种和强表面酸性位点的生成,提高了丙烷燃烧反应活性;Pt-Nb/ZrO2催化剂上载体表面的部分Nb2O5被Pt物种包覆,使得生成的表面Pt-Nb2O5界面低于Pt-Mo/ZrO2催化剂,但由于催化剂表面酸性位的提升,也促进了丙烷燃烧反应活性的提高.XPS结果表明,在甲烷燃烧反应中,Pt-Nb/ZrO2催化剂上Ptn+物种能够更加稳定地存在,这可能是Nb2O5助剂提高Pt-Nb/ZrO2催化剂上甲烷燃烧活性的关键.而Pt-Mo/ZrO2催化剂上Ptn+物种在甲烷反应中可以更容易地被还原,并且由于MoO3的包裹导致暴露的Pt位点数量降低,使催化剂催化甲烷燃烧的活性受到抑制.可见,MoO3助剂更有利于C–C键活化,而Nb2O5助剂更有利于高键能的C–H键活化.综上,本文系统性地研究MoO3助剂和Nb2O5助剂对Pt/ZrO2催化剂上不同短链烷烃的燃烧反应的影响,证实了两种助剂的促进作用与碳链长度的关系是截然不同的.     

CO2选择氧化低碳烷烃的研究进展

本文以低碳烷烃的选择催化氧化反应为对象，对几种CO₂选择氧化低碳烷烃的反应工艺进行了归纳总结，重点分析讨论了催化氧化反应中CO₂作为氧化剂的作用机制，并提出了研究展望。     

Ga2O3催化剂上CO2气氛中丙烷脱氢反应的研究

考察了Ga2O3对于丙烷脱氢和CO2气氛脱氢反应的催化性能.结果表明,Ga2O3具有较高的催化活性,其性能优于传统的Cr2O3脱氢催化剂.催化反应可能经过了一个丙烷异裂的过程,其中CO2是通过逆水煤气反应和Boudouard反应来促进催化剂性能的,在高于823K时该促进作用更为明显.催化剂的催化活性和其表面酸密度密切相关,在Ga2O3结构中,四配位Ga3+是其酸位的来源,并通过质子与氧化物的共同作用促进反应进行.催化剂的失活是由于表面的积碳和活性氧的消耗共同造成的.同时还对Ga2O3作为丙烷脱氢反应的催化剂的催化反应机理进行了初步探讨.     

静电纺丝法制备硼掺杂氧化硅纳米纤维用于低碳烷烃氧化脱氢制烯烃

乙烯和丙烯等低碳烯烃是重要的基础有机化工产品,广泛应用于化工生产的各个领域.相比于其他工艺,低碳烷烃氧化脱氢制烯烃工艺具有不受热力学平衡限制、无积炭等特点而被广泛研究.近年发现六方氮化硼(h-BN)、硼化硅(SiB6)和磷酸硼(BPO4)等非金属硼基催化剂能够高效催化烷烃氧化脱氢反应,并抑制产物烯烃的过度氧化,表现出高的催化活性和烯烃选择性.大量的研究表明,硼基催化剂活性起源于催化剂表面的"BO"物种(如B-O和B-OH等基团).氧化硼(B2O3)作为一种氧化气氛中化学性质稳定的含硼化合物,兼具丰富的"BO"位点,在反应条件下可形成多种结构以适用不同的化学环境,为制备高效的烷烃氧化脱氢催化剂提供了可能.在之前的研究中,多将B2O3浸渍在常规的TiO2,SiO2,A12O3等三维多孔载体上用于氧化脱氢反应.考虑到B2O3结构的灵活性和易于成键特性,需开发更为有效的合成策略,以提升B2O3催化剂在氧化脱氢反应中的活性和稳定性.本文采用静电纺丝技术合成了直径为100～150 nm的多孔掺硼二氧化硅纳米纤维(PBSN)用于低碳烷烃氧化脱氢反应.静电纺丝法合成的催化剂中硼物种在开放的氧化硅纤维骨架上均匀分散且稳定固载.一维纳米纤维结构不仅有利于扩散,且赋予催化剂在高重时空速(WHSV)条件下优异的烷烃氧化脱氢反应活性.在乙烷氧化脱氢反应中,当乙烷的转化率达到44.3％时,乙烯的选择性和产率分别为84％和44.2 μmol gcat-1 s-1.而在丙烷脱氢反应中,当丙烷转化率为19.2％时,总烯烃选择性及丙烯产率分别为90％和76.6 μmol gcat-1 s-1.在温度为545 ℃,丙烷WHSV高达84.6 h-1的条件下,催化剂保持长时间稳定.与其他负载型氧化硼催化剂相比,PBSN催化剂具有更高的烯烃选择性和稳定性.研究表明,在氧化硅负载B2O3催化剂催化丙烷氧化脱氢反应中,载体中Si-OH基团的存在可能会降低丙烯的选择性.瞬态分析和动力学实验表明,硼基催化剂催化烷烃氧化脱氢反应过程中O2的活化受到烷烃的影响.本文不仅为高效硼基催化剂的合成提供了新思路,也为深入理解该类催化剂上烷烃氧化脱氢反应过程提供了实验支撑.     

CrOx/SiO2催化剂上丙烷在CO2气氛中脱氢反应的研究

采用XRD、UV-vis DRS、ESR和微分吸附量热等技术,考察了铬担载量分别为2.5、5和10wt%的CrO_x/SiO₂催化剂的结构、表面性质和氧化还原性能。结果表明,催化剂表面上存在多种Cr的氧化态和聚集形式。随着Cr担载量从2.5wt%到10wt%的逐渐增大,催化剂表面占主导地位的Cr物种由CrO₃单体转为多聚CrO₃和Cr₂O₃晶相。在CO₂气氛中催化剂对丙烷转化率和丙烯选择性的大小顺序为2.5wt%CrO_x/SiO₂>5wt%CrO_x/SiO₂>10wt%CrO_x/SiO₂,反应过程中的原位ESR和UV-visDRS测定结果表明,催化剂表面的反应活性中心为Cr⁵⁺,Cr⁵⁺可由催化剂预处理过程中Cr³⁺的氧化及丙烷反应过程中CrO₃单体的还原产生,在反应中CO₂可使Cr³⁺重新氧化为Cr⁵⁺.     

Performance of ionic liquid as catalyst in the copolymerization of phenyl glycidyl ether with carbon dioxide

Summary Selective ammoxidation of ethylene over Co-ZSM-5 prepared by aqueous and solid-state ion exchange has been studied. The catalyst prepared using solid-state exchange showed higher activity and selectivity to acetonitrile. Catalysts tested in the ammoxidation of ethylene were previously characterized by chemical analysis, XRD, N₂-BET measurements and FTIR. TPD of ammonia and FTIR of pyridine used as probe molecule showed that solid-state ion exchange of H-ZSM-5 with cobalt generates new Lewis acid sites which seem to play a role in the ammoxidation reaction.     

纳米Cr2O3系列催化剂上CO2氧化乙烷脱氢制乙烯反应

 采用溶胶－凝胶法和共沸蒸馏法耦合技术制备了纳米Cr2O3催化剂，并采用共沉淀法和共沸蒸馏法耦合技术制备了纳米Cr2O3／Al2O3，Cr2O3／ZrO2和Cr2O3／MgO复合催化剂．应用BET，XRD，XPS，TPR和TEM等物理化学方法对催化剂的结构和物化性质进行了表征，并考察了该系列催化剂上CO2氧化乙烷脱氢制乙烯的反应性能．结果表明，纳米Cr2O3催化剂上乙烷和CO2的转化率均明显高于常规Cr2O3催化剂，但乙烯的选择性低于常规Cr2O3催化剂；纳米复合催化剂中的复合成分显著影响催化剂的催化性能．其中，10％Cr2O3／MgO纳米复合催化剂在温度为973K时，乙烷转化率和乙烯选择性分别可达到61．54％和94．79％．纳米催化剂表面Cr的还原性以及Cr6＋／Cr3＋比值是影响乙烷转化率和乙烯选择性的重要因素．     

Niobium phosphates as new highly selective catalysts for the oxidative dehydrogenation of ethane

Several niobium phosphate phases have been prepared, fully characterized and tested as catalysts for the selective oxidation of ethane to ethylene. Three distinct niobium phosphate catalysts were prepared, and each was comprised predominantly of a different bulk phase, namely Nb(2)P(4)O(15), NbOPO(4) and Nb(1.91)P(2.82)O(12). All of the niobium phosphate catalysts showed high selectivity towards ethylene, but the best catalyst was Nb(1.91)P(2.82)O(12), which was produced from the reduction of niobium oxide phosphate (NbOPO(4)) by hydrogen. It was particularly selective for ethylene, giving ca. 95% selectivity at 5% conversion, decreasing to ca. 90% at 15% conversion, and only produced low levels of carbon oxides. It was also determined that the only primary product from ethane oxidation over this catalyst was ethylene. Catalyst activity also increased with time-on-line, and this behaviour was ascribed to an increase of the concentration of the Nb(1.91)P(2.82)O(12) phase, as partially transformed NbOPO(4), formed during preparation, was converted to Nb(1.91)P(2.82)O(12) during use. Catalysts with predominant phases of Nb(2)P(4)O(15) and NbOPO(4) also showed appreciable activity and selectivities to ethylene with values around 75% and 85% respectively at 5% ethane conversion. The presence of phosphorous is required to achieve high ethylene selectivity, as orthorhombic and monoclinic Nb(2)O(5) catalysts showed similar activity, but displayed selectivities to ethylene that were <20% under the same reaction conditions. To the best of our knowledge, this is the first time that niobium phosphates have been shown to be highly selective catalysts for the oxidation of ethane to ethylene, and demonstrates that they are worthy candidates for further study.     

Selective oxidation and ammoxidation of ethane over ion-exchanged Co-MCM-49 zeolites

Summary Ion-exchanged Co-Na-MCM-49 and Co-H-MCM-49 zeolites are active catalysts for the selective oxidation and ammoxidation of ethane. The presence of ammonia in the feeds can considerably improve the selectivity and yield of the sum of ethylene and acetonitrile.     

电场增强催化甲烷合成碳二烃催化剂影响研究

本研究提出了在常温、常压电场增强等离子体条件下甲烷直接转化合成碳二烃的洁净工艺 ,在不同的放电电压、放电功率、甲烷进料流量和不同的催化剂作用下 ,甲烷能够以不同的转化率和选择性转变为碳二烃。对影响甲烷转化率和碳二烃选择性的因素 :放电电压、放电功率、甲烷进料流量和催化剂进行了研究 ,对催化剂性能进行了比较 ,并探讨了反应机理。结果表明 ,适宜的工艺条件 :放电电压 2 0kV～ 4 0kV ;输入功率 :2 0W～ 4 0W ;合适的甲烷进料流量 :30mL/min～ 70mL/min。在该条件下 ,碳二烃的选择性可以达到 95 % ;催化剂对甲烷转化率的影响顺序为MnO2 /Al2 O3 >Ni/Al2 O3 >MoO3 /Al2 O3 >Ni/NaY >Pd/ZSM 5 >Ni/H4Mg2 Si3 O4>Ni/ZSM 5 >Co/ZSM 5 >无催化剂。     

Surface Acidity／Basicity and Catalytic Reactivity of CeO2／γ—A12O3 Catalysts for the Oxidative Dehydrogenation of Ethane with Carbon Dioxide to Ethylene

Dehydrogenation of ethane to ethylene in CO2 was investigated over CeO2/γ-Al2O3 catalysts at 700℃ in a conventional flow reactor operating at atmospheric pressure. XRD, BET and microcalorimetric adsorption techniques were used to characterize the structure and surface acidity/basicity of the CeO2/γ-Al2O3 catalysts. The results show that the surface acidity decreased while the surface basicity increased after the addition of CeO2 to γ-Al2O3. Accordingly, the activity of the hydrogenation reaction of CO2 increased, which might be responsible for the enhanced conversion in the dehydrogenation of ethane to ethylene. The highest ethane conversion obtained was about 15% for the 25?O2/γ-Al2O3. The selectivity to ethylene was high for all the CeO2, γ-Al2O3 and CeO2/γ-Al2O3 catalysts.     

Ni基催化剂上的乙烷部分氧化制合成气

There is abundant supply of light alkanes and relatively few routes of converting them to more valuable products. Although CH4 predominates in natural gas, it also contains C2H6, C3H8 and C4H10 (from 5 % to 30% ), and with C2H6 as the most abundant secondary component[1]. Partial oxidation of methane to syngas (CH4 +0.5O2 →CO + 2H2) over nickel-based catalysts has received intensive attention[2]and much research has been devoted to conversion of ethane to ethylene[3]. Ethylene has been shown to be formed from ethane by thermal dehydrogenation (C2H6 →C2H4 + H2) and oxidative dehydrogenation (C2H6 + 0. 5O2 →C2H4 + H2O). These processes are operated under severely fuel-rich conditions. The carbon-deposition and consequent deactivation of the catalysts are major problems, which leads to poor conversion of the above mentioned reactions. As an alternative strategy for the elaboration of ethane, little work on the partial oxidation of ethane (POE) to syngas over nickel-based catalysts has been reported. Provided it could be produced from C2H6with high selectivity and high conversion over nickel-based catalysts, syngas could be directly obtained from natural gas including CH4 and C2H6 with high selectivity and conversion. This may lead to better utilization of the light fractions from natural gas and refineries. In the present paper, POE to syngas over nickel-based catalysts was investigated.     

负载型Co-Cr氧化物催化剂上CO2氧化乙烷脱氢制乙烯反应的研究

制备了一系列不同Co／Cr比例的Co-Cr／SiO2和Co-Cr／γ-Al2O3催化剂，并应用XRD等技术对所制样品进行了表征．在常压连续流动固定床石英反应器中考察了它们对CO2乙烷氧化脱氢反应的催化性能．实验结果表明，Co-Cr／SiO2和Co-Cr／γ-Al2O对CO2乙烷脱氢制乙烯都有较高的催化活性，其活性都明显高于负载单一组分的催化剂．以γ-Al2O为载体的催化剂活性明显比以SiO2为载体的催化剂活性高．1％Co-5％Cr／γ-Al2O活性最高，973K乙烷的转化率达25．57％，乙烯的选择性和收率分别达94．28％、24．10％．     

Selective esterification of glycerol with acetic acid to diacetin using antimony pentoxide as reusable catalyst

Glycerol can be obtained as a by-product during biodiesel manufacture. It is important to convert glycerol to value-added products. Glycerol esterification with acetic acid is one of the most promising approaches for glycerol utilization. It is usually difficult to obtain diacetin with good activity and selectivity. In this work, glycerol esterification with acetic acid over different metal oxides, such as Bi2O3, Sb2O3, Sn O2, Ti O2, Nb2O5 and Sb2O5, was investigated. It was found that in the six investigated metal oxides, only Sb2O5 resulted in good activity and selectivity to diacetin. Under the optimized conditions, the glycerol conversion reached 96.8%,and the selectivity to diacetin reached 54.2%, while the selectivity to monoacetin and triacetin was 33.2% and12.6%, respectively. The catalysts were characterized with FT-IR spectra of adsorbed pyridine, which indicated that in the six investigated metal oxides, only Sb2O5 possessed Br?nsted acid sites strong enough to protonate adsorbed pyridine. The good catalytic activity and selectivity to diacetin might be mainly attributable to the Br?nsted acid sites of Sb2O5. Reusability tests showed that with Sb2O5 as catalyst, after six reaction cycles, no significant change in the glycerol conversion and the selectivity to diacetin was observed.     

Experimental investigation of fluidized-bed reactor performance for oxidative coupling of methane

Performance of the oxidative coupling of methane in fluidized-bed reactor was experimentally investigated using Mn-Na2WO4/SiO2,La2O3/CaO and La2O3-SrO/CaO catalysts.These catalysts were found to be stable,especially Mn-Na2WO4/SiO2 catalyst.The effect of sodium content of this catalyst was analyzed and the challenge of catalyst agglomeration was addressed using proper catalyst composition of 2%Mn2.2%Na2WO4/SiO2.For other two catalysts,the effect of Lanthanum-Strontium content was analyzed and 10%La2O 3-20%SrO/CaO catalyst was found to provide higher ethylene yield than La2O3/CaO catalyst.Furthermore,the effect of operating parameters such as temperature and methane to oxygen ratio were also reviewed.The highest ethylene and ethane (C2) yield was achieved with the lowest methane to oxygen ratio around 2.40.5% selectivity to ethylene and ethane and 41% methane conversion were achieved over La2O3-SrO/CaO catalyst while over Mn-Na2WO4 /SiO2 catalyst,40% and 48% were recorded,respectively.Moreover,the consecutive effects of nitrogen dilution,ethylene to ethane production ratio and other performance indicators on the down-stream process units were qualitatively discussed and Mn-Na2WO4/SiO2 catalyst showed a better performance in the reactor and process scale analysis.