Surface segregation in liquid GaSn alloys by AES

The surface segregation of Sn in liquid GaSn alloys has been studied by Auger electron spectroscopy as a function of bulk concentration at 350° C. The Sn was found to be strongly adsorbed at the surface. The surface concentrations of Sn and Ga were calculated from the Auger measurements using inelastic mean free paths and backscattering factors estimated in recent theoretical work. The values found for the surface concentrations are essentially in agreement with those deduced from surface tension measurements using Gibbs adsorption theory. This result supports a monolayer adsorption distribution in the GaSn system.     

Disorder broadening of alloy Auger spectra

Auger spectroscopy promises the means to separate initial and final state contributions to the disorder broadening of core XPS spectra in disordered alloys. Auger disorder broadening, deduced from recent ab initio results, is predicted to be greater than XPS disorder broadening for Cu₅₀Pd₅₀ and Ag₅₀Pd₅₀ alloys. Simulations are used to assess whether this effect is observable experimentally despite the greater lifetime broadening of Auger spectra. A number of cases where narrow core–core–core Auger transitions should allow clear experimental identification of this effect are identified. The prospects for determining environment-resolved Auger spectra using APECS have been investigated.     

Surface composition of PdAu and PdAg catalysts by auger electron spectroscopy

Auger electron spectroscopy (AES) has been employed to examine the metal surface composition of PdAu and PdAg alloys as microspheres and as alumina-supported crystallites. For the PdAu system the observed PdAu ratios at the surface correspond closely to those of the bulk both for the microspheres and crystallites. However in the case of supported PdAg, the surface exhibits silver-enrichment relative to the bulk. By means of the regular solution monolayer model the results are interpreted theoretically and the binding energies between the dissimilar metal atoms are computed.     

Model and theory for the determination of diffusion coefficients by Auger electron spectroscopy measurements and an application to oxygen diffusion along the [0001] and [101¯0] axes in single crystal zirconium

A simple hopping model of the diffusion of adsorbed species from a surface into the bulk of a material has been formulated and solved mathematically. The difference in the energy barriers for an atom moving between the atomic layers at the surface and in the bulk are explicitly considered. This model is also capable of describing the initial stages of diffusion, something that conventional solutions of the continuum diffusion equation cannot handle. Auger electron spectroscopy has been used to measure the dissolution rate of oxygen from Zr(0001) and Zr(101¯0) surface into the bulk. Satisfactory results were obtained by applying our model to the diffusion data for these two zirconium surfaces for two different heating schedules: (i) rapid temperature ramp-and-hold and (ii) continuous linear heating with respect to time. The resulting Arrhenius expressions for diffusion are: D = (0.115 ± 0.031)exp[(−44.45 ± 4.82)kcal/RT]cm²/s along Zr[0001] and D = (1.07 ± 0.26)exp[(−46.18 ± 4.22)kcal/RT]cm²/s along Zr[101¯0].     

Study of ion desorption induced by a resonant core-level excitation of condensed H2O using Auger electron photo-ion coincidence (AEPICO) spectroscopy combined with synchrotron radiation

Ion desorption induced by a resonant excitation of O 1s of condensed amorphous H₂O has been studied by total ion and total electron yield spectroscopy, nonderivative Auger electron spectroscopy (AES) and Auger electron photo-ion coincidence (AEPICO) spectroscopy. The spectrum of total ion yield divided by total electron yield exhibits a characteristic threshold peak at hν = 533.4 eV, which is assigned to the 4a₁ ← O 1s resonant transition. The AES at the 4a₁ ← O 1s resonance is interpreted as being composed of the spectator-AES of the surface H₂O, and the normal-AES of the bulk H₂O, where the 4a₁ electron is delocalized before Auger transitions. H⁺ is found to be the only ion species in AEPICO spectra measured at the 4a₁ ← O 1s resonance and at the O 1s ionization (hν = 560 eV). The electron kinetic energy dependence of the AEPICO yield (AEPICO yield spectrum) at the 4a₁ ← O 1s resonance is found to be greatly different from that at the O 1s ionization. The peak positions of the AEPICO yield spectrum at the 4a₁ ← O 1s resonance are found to correspond to those of the spectator-AES of the surface H₂O, which is extracted from the AES at the 4a₁ ← O 1s resonance. Furthermore, the AEPICO yield is greatly enhanced at the 4a₁ ← O 1s resonance as compared with that at the O 1s ionization. On the basis of these results, a spectator-Auger-stimulated ion desorption mechanism and/or ultra-fast ion desorption mechanism are concluded to be responsible for the H⁺ desorption at the 4a₁ ← O 1s resonance. The enhancement of the H⁺ yield is ascribed to the O---H anti-bonding character of the 4a₁ orbital.     

The surface composition of the gold-palladium binary alloy system

The surface composition of the AuPd alloy system has been determined by Auger electron spectroscopy. Measurements were performed on polished polycrystalline alloy foils. After cleaning, the intensities of the 71 eV and 2024 eV gold Auger transitions, and the intensity of the 330 eV palladium transition were measured, and then converted to atom concentrations in the surface layer. The surfaces of the annealed samples were found to be significantly enriched in gold with respect to the bulk. This result disagrees with the regular solution theory prediction. After extensive sputtering of the AuPd alloys with 1.5 keV Ar⁺ ions, a slight surface enrichment with palladium was found, as predicted by the simple theoretical model for sputtering.     

Ge diffusion on Si surfaces

Ge diffusion on Si(100), (111), and (110) surfaces has been studied by Auger electron spectroscopy and low energy electron diffraction in the temperature range from 600 to 800 °C. Surface diffusion coefficients versus temperature have been measured.     

Surface segregation in Pt-Au alloys studied using Auger electron spectroscopy

Temperature dependent surface segregation studies using Auger electron spectroscopy have been performed on three different Pt-Au alloys, containing 2, 5 and 90 wt% Au. By utilizing Auger transitions of different kinetic energies and model segregation profiles, an estimate of the in-depth variation in composition was made. Strong surface segregation of Au was observed in the three alloys.     

X-ray photoelectron and X-ray Auger electron spectroscopy studies of heavy ion irradiated C60 films

The influence of 200 MeV Au ion irradiation on the surface properties of polycrystalline fullerene films has been investigated. The X-ray photoelectron and X-ray Auger electron spectroscopies are employed to study the ion-induced modification of the fullerene, near the surface region. The shift of C 1s core level and decrease in intensity of shake-up satellite were used to investigate the structural changes (like sp² to sp³ conversion) and reduction of π electrons, respectively, under heavy ion irradiation. Further, X-ray Auger electron spectroscopy was employed to investigate hybridization conversion qualitatively as a function of ion fluence.     

Photoemission measurements of bulk,surface and hydrogen induced states on cleaved Ge(111)

Ultraviolet photoemission spectroscopy using HeI (21.2 eV) resonance photons has been used to study cleaved Ge(111) surfaces which were also characterized by Auger electron spectroscopy and low energy electron diffraction. Higher effective resolution for both bulk and surface states was found than for recent measurements employing synchrotron radiation.     

Segregation of Pt at clean surfaces of (Pt, Ni)3Al

Experimental evidence for surface segregation of Pt at (1 1 1) surfaces of ternary (Pt, Ni)₃Al alloys is presented, based upon Auger electron spectroscopy, low energy ion scattering, and angle-resolved X-ray photoelectron spectroscopy. Density functional calculations in the dilute limit confirm that Pt segregation is energetically favored.     

超高真空俄歇电子能谱原位加热和GaN热效应研究

建立一套基于超高真空俄歇电子能谱的原位加热系统,对GaN薄膜进行热效应研究．随着温度的增加,Ga LMM和Ga MVV的动能减小．利用第一性原理计算,获得理论的GaMVV俄歇谱.加热过程由于晶格热膨胀以及表面原子再构引起价电子态密度发生变化,从而导致价带俄歇谱负移．     

Backscattering correction for quantitative Auger analysis: II. Verifications of the backscattering factors through quantification by AES

The validity and utility of the backscattering correction factors obtained from Monte Carlo calculations for quantitative analysis by Auger electron spectroscopy (AES) were examined through practical quantification of surface concentrations of binary alloys. Quantifications were attempted, first, to access the surface composition of a sputter-deposited NiPt layer, which is probably the most appropriate test-sample with known surface composition for surface analysis. The quantification by AES has led to the result that the surface composition of the layer agrees well with the bulk composition of the sputtered NiPt alloy, as expected. The composition of a sputtered AuCu alloy surface was, then, examined according to the same correction procedure as for the NiPt layer, leading to the confirmation that no preferential sputtering is observed for AuCu alloys by AES as Färber et al. reported.     

Sequential ISS-AES measurement with scanning auger microprobe

Continuous measurement of ion scattering spectroscopy (ISS) and Auger electron spectroscopy (AES) has been achieved in a single energy scan of a cylindrical mirror analyzer by introducing a floating high voltage power supply to the conventional AES system. This technique was applied for Au-Cu alloys to study the surface composition of the sputtered surface by ISS and AES sequentially. The result agrees well with the other works obtained by AES and by ISS separately.     

Coadsorption of lanthanum with boron and gadolinium with boron on Mo(1 1 0)

Submonolayer to multilayer coadsorption of lanthanum (La) with boron (B) and gadolinium (Gd) with boron on the surface of Mo(1 1 0) has been studied by means of Auger electron spectroscopy (AES), electron energy loss spectroscopy (EELS) and work function () measurements. The equilibrium state of double adsorbate systems achieved either by adsorption of rare-earth metal (REM) on boron precovered Mo(1 1 0) surface held at room temperature or after moderate annealing of the system with opposite order of adsorption (B on REM films) is the layer which is the inhomogeneous mixture of boron and REM atoms with preferential concentration of boron in the surface area of the mixed film. The work function of such films even at REM to boron concentration ratio much higher than 1/6 are very close to the values of corresponding bulk LaB₆ and GdB₆, favoring assumption of surface rearrangement as the dominant reason of high electron emission efficiency of hexaborides. Almost total similarity of the results for La–B and Gd–B systems can be viewed as the consequence of weak participation of Gd f-electrons in determining the thermionic properties of corresponding double layers.     

Sputtering of SiC with low energy He and Ar ions under grazing incidence

The effect of low energy sputtering under grazing incidence upon the surface composition of SiC was investigated by Auger electron spectroscopy. The energy of the sputtering projectiles (He, Ar) varied from 200 to 1500?eV. Peak shifts to the higher energies with increasing argon ion energy were observed for all silicon and carbon Auger transitions. These shifts were explained by enhanced damage of the surface region within the sampling depth of the Auger electrons. The insensitivity of the Auger peak position to the energy of helium ions indicates that the damage state in the surface region does not change with the increasing energy of helium ions. An increase of the carbon concentration with the decrease of the argon energy was observed. The experiments were accompanied by dynamic Monte Carlo simulations by the TRIDYN code.     

Surface composition and depth concentration profile of platinum/tin alloys from combined X-ray photoelectron and Auger spectroscopic data

Auger electron spectroscopy (AES) and X-ray photoelectron spectroscopy (X-PS) have been combined to study surface enrichment of two platinum/tin alloys, viz. PtSn and Pt₃Sn, effected by reduction in hydrogen at 550°C. By making use of the different information depths of AES and X-PS for this alloy system, as determined by the corresponding mean free paths of inelastic scattering of the emitted characteristic electrons, a rather detailed picture has been obtained of the composition of the topmost atomic layers in these alloys. It is shown that both alloys exhibit phenomena of surface enrichment and depletion of the underlying layers over distances of the order of 10 Å.     

Determination of the surface composition of palladium-nickel alloy film catalysts using Auger electron spectroscopy

Palladium-nickel films evaporated in UHV on room temperature substrates form alloys of good bulk homogeneity as indicated by X-ray diffraction. The average composition of the outermost 3 to 5 atom layers has been determined from the intensities of the high energy 848 eV nickel and 330 eV palladium Auger electrons. This average composition is in close agreement with the bulk composition determined by X-ray diffraction, X-ray fluorescence and atomic absorption spectrophotometry. If the nickel concentration is determined from the intensity of the low energy 61 eV nickel Auger electrons, when the analysis refers more critically to the first 1 to 3 atom layers, then a surface enrichment of palladium is indicated for all alloy compositions. From the decrease in the relative intensities of the low energy and high energy nickel Auger electrons with increasing palladium concentration it may be deduced that the enrichment of palladium in the first atom layer is higher than in the second and third layers and that a complete monolayer of palladium is formed for bulk concentrations of 65 at% or more. The experimental observations are in qualitative agreement with theoretical predictions of surface composition from bulk thermodynamic data. The palladium-nickel alloys form a range of surface compositions which can be controlled by changing the bulk composition and which are useful for studying catalytic activity as a function of composition. The alloy films are stable under electron irradiation in the AES analysis in UHV but air exposed films analysed in a residual pressure of 1.3 microPa water vapour show a decrease in palladium surface concentration on irradiation indicating a diffusion of nickel to the surface to form an overlayer of nickel oxide.     

Substitutional adsorption of K on Fe(100)

The adsorption of potassium on Fe(100) was studied by time-of-flight forward scattering and recoiling spectroscopy (TOF-SARS), low energy electron diffraction (LEED) and Auger electron spectroscopy (AES). After heating to 650 K of the potassium saturated surface the formation of a p(3 × 3) potassium superstructure was observed by LEED. TOF-SARS experiments ruled out the adsorption of potassium in the on-top, bridge and four-fold hollow site. The only site which is in agreement with all experimental results is the substitutional site where K replaces an Fe atom of the topmost layer of the crystal. This is the first time a substitutional adsorption site has been found on a bcc surface. On an fcc surface such an adsorption site has been found recently for adsorption of sodium and potassium on Al(111).     

Secondary and auger electron spectra of a Cu-Be alloy

The slow secondary electron spectra corresponding to the copper rich surface and oxidized beryllium surface of Cu-Be alloys are observed after argon ion bombardment and heating treatment of the sample and they are identified by Auger electron spectroscopy.