三维浅海下弹性结构声辐射预报的有限元-抛物方程法

利用多物理场耦合有限元法对结构和流体适应性强、抛物方程声场计算高效准确的特点,提出了三维浅海波导下弹性结构声振特性研究的有限元-抛物方程法.该方法采用多物理场耦合有限元理论建立浅海下结构近场声辐射模型,计算局域波导下结构声振信息,并提取深度方向上复声压值作为抛物方程初始值;然后采用隐式差分法求解抛物方程以步进计算结构辐射声场.重点介绍了该方法对浅海下结构声辐射计算的准确性、高效性以及快速收敛性后,对Pekeris波导中有限长弹性圆柱壳的声振特性进行了分析.研究得出,当圆柱壳靠近海面(海底)时,其耦合频率比自由场下的要高(低),当潜深达到一定范围时,与自由场耦合频率基本趋于一致;在低频远场,结构辐射场与同强度点源声场具有一定的等效性,且等效距离随着频率增加而增加;由于辐射声场受结构振动模态、几何尺寸和简正波模式影响,结构辐射场传播的衰减规律按近场声影响区、球面波衰减区、介于球面波和柱面波衰减区、柱面波衰减区四个扩展区依次进行.     

结构声辐射的振动模态分析和声辐射模态分析研究

基于辐射声功率的二次型表达式,采用有限元法、Rayleigh积分和边界元法对结构声辐射进行了振动模态分析和声辐射模态分析研究。振动模态间的耦合对辐射声功率影响的研究表明: 结构各阶振动模态自身对结构辐射声功率的贡献是增大结构的辐射声功率,而振动模态间的耦合可能会增大结构辐射声功率,也可能会减小结构辐射声功率,或对辐射声功率没有影响。而且,当振动模态间的耦合作用对辐射声功率的影响不大时,采用振动模态控制可取得较好的减振降噪双重控制效果。将混合的Helmholtz积分方程方法用广义逆引入到三维复杂结构声辐射分析的声辐射模态公式中,解决了特征频率下解不唯一问题。还研究了正方形封闭空间结构声辐射模态的辐射效率和形状,并对结构声辐射的振动模态控制和声辐射模态控制进行了讨论。     

基于联合波叠加法的浅海信道下圆柱壳声辐射研究

针对浅海信道下弹性结构声辐射预报尚无高效可靠的研究方法,提出了一种浅海信道下弹性结构声辐射快速预报的联合波叠加法.该方法结合了浅海信道传输函数、多物理场耦合数值计算法和波叠加法理论,运用该方法可对浅海信道下弹性结构辐射声场进行快速预报.经数值法和解析解法验证后,从信道下辐射源、环境影响和辐射声场测量的角度研究分析了浅海信道下弹性圆柱壳的声辐射特性,阐释了进行浅海信道下结构声辐射研究的必要性.研究结果表明,仅在低频浅海信道下弹性结构可近似等效为点源,信道上下边界对声场产生显著的耦合影响,高频段的空间声场指向性分布尤为明显,垂直线列阵进行信道下结构辐射声功率测量时,测量结果受到信道环境边界和潜深的影响较大.     

散热片对变压器声辐射的影响及优化分析

油浸式配电变压器表面布有大量散热片结构,使得油箱振动声辐射变得复杂.该文研究了散热片结构对油浸式变压器辐射声场的影响,在此基础上提出了散热片结构尺寸的优化措施.建立了考虑流固耦合的变压器振动和声学分析模型,提出了散热片声场效应评判准则,基于模态分析和频响分析探讨了散热片对变压器振动声辐射影响的振动效应、声源效应和声障效...     

用傅里叶变换红外光谱研究增强UV-B辐射对PSⅡ蛋白结构的影响

运用傅里叶变换红外光谱技术研究了增强紫外线-B(UV-B)辐射对植物光系统Ⅱ(PSⅡ)中膜蛋白结构的影响.结果显示在增强的UV-B辐射条件下,PSⅡ中蛋白的α-螺旋、β-折叠强度增加,而β-转角的强度下降了近一倍,并且这些结构与周围的耦合减弱.此外,UV-B辐射使酪氨酸残基苯酚环的结构发生改变,并使其微极性降低.UV-...     

基于声辐射模态的有源结构声传入及其辐射控制

从辐射模态的概念和角度研究利用结构误差传感方法对弹性封闭空间结构声辐射进行传感和有源控制。首先分析了辐射模态的数学和物理意义并揭示了辐射模态与声腔模态之间的内在耦合关系。通过声辐射模态建立了弹性封闭空间结构声辐射传感和有源控制模型,并提出了通过传感器阵列测量结构表面有限点的振速分布和设计特定的辐射模态空间滤波器来获得控制所需的误差信号。在此基础上对封闭空间结构声辐射有源控制和误差传感策略进行了深入的理论和数值仿真分析,重点讨论了传感器的数量和布放对辐射模态传感及其有源控制效果的影响。结果表明:辐射模态与声腔模态的耦合具有严格的选择性,各阶辐射模态的形状和与相耦合的主导声模态在耦合面上的形状非常相似;利用结构传感技术传感封闭空间的辐射模态时测点不足或空间采样不足将可能产生较严重的模态泄漏问题,使得不希望的结构模态泄露进所测的辐射模态当中来。在低频范围内,一般只需传感并最小化前三阶有效辐射模态声势能,在更低频和空间声模态频率附近,只需最小化前一阶最有效辐射模态声势能,便能和总声势能最小化策略控制效果基本一样。      

基于Zernike系数优化模型的光学反射镜支撑结构拓扑优化设计方法

使用Zernike多项式表征镜面的变形,应用伴随变量法推导Zernike系数对拓扑优化设计变量的敏度,克服了差分法求解敏度时计算量大的问题,实现了基于Zernike系数直接建构具有成千上万设计变量的优化模型的目标函数以及设计约束.同时,在有限元数值离散的理论框架下,采用有限单元基函数以及单元数值积分的程序实现了结构变形以及Zernike系数的求解,简化了计算流程的同时还能保证计算精度.本文算法可以对目标函数或约束为线性组合的Zernike系数的一般结构拓扑优化模型进行优化,具有一定的泛用性.     

复杂结构声辐射模态的计算

结构辐射阻矩阵的特征向量就是其声辐射模态,复杂结构的辐射阻矩阵获取困难阻碍了声辐射模态理论的进一步应用。为此提出一种基于等效源方法的复杂结构辐射阻矩阵计算方法,由此形成了一套完整的计算复杂结构声辐射模态方法。最后通过仿真算例对影响结构辐射阻矩阵计算精度的因素进行了分析,给出了复杂结构辐射阻矩阵构造的一般原则。理论推导和数值仿真算例表明所提出的复杂结构声辐射模态计算方法是有效的。该方法简化了复杂结构声辐射模态的计算,计算效率较高。     

铁电材料中的极性拓扑结构

调控磁性材料中的自旋拓扑结构(流量闭合型、涡旋、半子(meron)、斯格明子(skyrmion)等自旋组态)可以改进材料的磁性和电磁性能,因而引起了学术界的广泛关注.最近研究表明,在尺寸效应、界面耦合及其相互作用、外延应变等作用下,铁电材料中也会出现自发的极性拓扑畴结构,同时表现出新的铁电相结构和丰富的物理性能.本文总结了铁电纳米结构、铁电薄膜和铁电超晶格中的极性拓扑畴结构类型及其形成机理,分析了这些极性拓扑结构与铁电、压电、介电、光电性能之间的关联,并分别讨论了铁电材料中极性拓扑结构的整体拓扑相变调控和单个极性拓扑结构的外场调控,最后展望了极性拓扑结构未来的可能研究方向.     

拓扑成像法的分层波导结构内部缺陷检测

将拓扑成像理论应用于分层波导结构,分析拓扑成像法在分层波导结构缺陷检测方面的应用可行性。首先,对拓扑梯度的表达式进行理论推导,阐述拓扑成像的基础理论和成像原理,对于厚度方向刚性连接的钢-铝双层板,本文结合实际检测需求,提出了优化的拓扑梯度表达式。然后,使用ANSYS有限元软件建立声场计算模型,根据优化的拓扑梯度表达式计算了直接问题和伴随问题两种情况下的声场分布,验证拓扑成像理论的可靠性。结果表明,拓扑成像方法可以准确定位钢-铝双层板中单缺陷和多缺陷,且具有良好的检测分辨率和定位精度,说明拓扑成像法对分层波导结构中的缺陷检测具有可行性。     

Shape optimization of multi-chamber cross-flow mufflers by SA optimization

It is essential when searching for an efficient acoustical mechanism to have an optimally shaped muffler designed specially for the constrained space found in today's plants. Because the research work of optimally shaped straight silencers in conjunction with multi-chamber cross-flow perforated ducts is rarely addressed, this paper will not only analyze the sound transmission loss (STL) of three kinds of cross-flow perforated mufflers but also will analyze the optimal design shape within a limited space.In this paper, the four-pole system matrix used in evaluating acoustic performance is derived by using the decoupled numerical method. Moreover, a simulated annealing (SA) algorithm, a robust scheme in searching for the global optimum by imitating the softening process of metal, has been adopted during shape optimization. To reassure SA's correctness, the STL's maximization of three kinds of muffles with respect to one-tone and dual-tone noise is exemplified. Furthermore, the optimization of mufflers with respect to an octave-band fan noise by the simulated algorithm has been introduced and fully discussed. Before the SA operation can be carried out, an accuracy check of the mathematical model with respect to cross-flow perforated mufflers has to be performed by Munjal's analytical data and experimental data.The optimal result in eliminating broadband noise reveals that the cross-flow perforated muffler with more chambers is far superior at noise reduction than a muffler with fewer chambers. Consequently, the approach used for the optimal design of noise elimination proposed in this study is certainly easy and efficient.     

微动粒子群优化算法用于Egun的多参量优化

 针对2维电子光学多参量优化问题,采用微动粒子群优化算法,在给出目标电子轨迹和优化范围的前提下,可以得到趋近于该电子轨迹的真空边界和聚束磁结构。该算法分为前后两阶段：第一阶段采用前后试探法(微动),同时参照最优粒子的信息;第二阶段采用标准粒子群优化算法。针对涉及多个相关参量的电子光学设计问题,标准粒子群优化算法仅能保证以较高概率收敛到局部最佳解,而微动粒子群优化算法能以较高概率收敛到全局最佳解,并且展现了多核计算机在电子光学设计上的潜力。初步的软件试验显示：消耗人类工程师几周时间的电子光学设计问题,用微动粒子群算法在普通个人计算机上几十小时就能完成。     

Adaptive population-based multi-objective optimization in SDN controllers for cost optimization

In Wireless Sensor Networks, Software Defined Networks (SDN) provide a logically centralized control plane as a potential means of streamlining network management (WSNs). The employment of several SDN controllers to build a physically distributed SDN is a common tactic to boost speed, expand scalability, and offer fault tolerance. However, the deployment of many controllers results in increased synchronization and deployment expenses. Therefore, selecting the optimal location for SDN controllers to improve WSN performance is a research issue. In this paper, the multi-objective optimization problem known as the controller placement problem (CPP) is initially formulated. Cost, time, and reliability are just a few of the restraints that are taken into consideration in this regard. In addition, a new Adaptive Population-Based Cuckoo Optimization (APB-CO) for optimal controller placement is implemented. In the end, APB-CO performs experiments to validate the efficacy by analyzing Sync (7.5), Coverage (47), Controller Cost (4.8), and Fitness (0.6983) for the 100th node variation at network 1. The proposed model obtained the controller cost as 34.4, compared to the existing method such as Simulated Annealing (44.3) and Greedy Approach (42.6).     

Deterministic modularity optimization

We study community structure of networks. We have developed a scheme for maximizing the modularity Q [Newman and Girvan, Phys. Rev. E 69, 026113 (2004)] based on mean field methods. Further, we have defined a simple family of random networks with community structure; we understand the behavior of these networks analytically. Using these networks, we show how the mean field methods display better performance than previously known deterministic methods for optimization of Q.     

Structural-acoustic topology optimization analysis based on evolutionary structural optimization approach

The continuum structural-acoustic topology optimization with external loading is investigated herein. Finite element method （FEM） is used to obtain the structural frequency response and boundary element method （BEM） is adopted to perform exterior acoustic radiation analysis. The evolutionary structural optimization （ESO） is served as an optimization method in structural-acoustic radiation topology analysis. The acoustic radiation optimization of a plate under harmonic excitation is given for example. The numerical results show that using ESO solution to analyze structural-acoustic topology optimization is feasible and effective.     

Structural optimization of Au–Pd bimetallic nanoparticles with improved particle swarm optimization method

Due to the dependence of the chemical and physical properties of the bimetallic nanoparticles(NPs) on their structures,a fundamental understanding of their structural characteristics is crucial for their syntheses and wide applications. In this article, a systematical atomic-level investigation of Au–Pd bimetallic NPs is conducted by using the improved particle swarm optimization(IPSO) with quantum correction Sutton–Chen potentials(Q-SC) at different Au/Pd ratios and different sizes. In the IPSO, the simulated annealing is introduced into the classical particle swarm optimization(PSO) to improve the effectiveness and reliability. In addition, the influences of initial structure, particle size and composition on structural stability and structural features are also studied. The simulation results reveal that the initial structures have little effects on the stable structures, but influence the converging rate greatly, and the convergence rate of the mixing initial structure is clearly faster than those of the core-shell and phase structures. We find that the Au–Pd NPs prefer the structures with Au-rich in the outer layers while Pd-rich in the inner ones. Especially, when the Au/Pd ratio is 6:4, the structure of the nanoparticle(NP) presents a standardized Pd_(core) Au_(shell) structure.     

Nonparametric search optimization method

Translated from Izvestiya Vysshikh Uchebnykh Zavedenii, Fizika, No. 9, pp. 65–73, September, 1995.     

Solid-perforated panel layout optimization by topology optimization based on unified transfer matrix

This paper presents a numerical method for the optimization of the sequencing of solid panels, perforated panels and air gaps and their respective thickness for maximizing sound transmission loss and/or absorption. For the optimization, a method based on the topology optimization formulation is proposed. It is difficult to employ only the commonly-used material interpolation technique because the involved layers exhibit fundamentally different acoustic behavior. Thus, an optimization method formulation using a so-called unified transfer matrix is newly proposed. The key idea is to form elements of the transfer matrix such that interpolated elements by the layer design variables can be those of air, perforated and solid panel layers. The problem related to the interpolation is addressed and bench mark-type problems such as sound transmission or absorption maximization problems are solved to check the efficiency of the developed method.