Certified reference materials for inorganic and organic contaminants in environmental matrices

Chemical measurements often constitute the basis for informed decision-making at different levels in society; sound decision-making is possible only if the quality of the data used is uncompromised. To guarantee the reliability and comparability of analytical data an intricate system of quality-assurance measures has to be put into effect in a laboratory. Reference materials and, in particular, certified reference materials (CRMs) are essential for achieving traceability and comparability of measurement results between laboratories and over time. As in any other domain of analytical chemistry, techniques used to monitor the levels and fate of contaminants in the environment must be calibrated using appropriate calibration materials, and the methods must be properly validated using fit-for-purpose matrix-matched CRMs, to ensure confidence in the data produced. A sufficiently large number of matrix CRMs are available for analysis of most elements, and the group of chemicals known as persistent organic pollutants, in environmental compartments and biota. The wide variety of analyte/level/matrix/matrix property combinations available from several suppliers enables analysts to select CRMs which sufficiently match the properties of the samples they analyse routinely. Materials value-assigned for the so-called emerging pollutants are scarce at the moment, though an objective of current development programmes of CRM suppliers is to overcome this problem.     

Performance of a chromatographic procedure used in the certification of reference material for polycyclic aromatic hydrocarbons in sewage sludge

Semi-automatic capillary gas chromatographic method with classical flame ionization detection, which satisfies the conditions for required performance and gave acceptable results within the framework of an interlaboratory certification programme for PAHs in sewage sludge, is described. The interesting feature of the procedure is that it incorporates automatic operations such as sample fractionation by semi-preparative HPLC, fraction collection at signal level recognition and evaporation under nitrogen flow. Multiple injections in the GC capillary column are performed in the on-column mode via an autosampler with temperature-programmable injector. Automatic data acquisition and chromatogram treatment are made via computer software. This partially automatic procedure releases personnel from tedious and time-consuming tasks and its robust character was validated through the certification of reference material for PAHs in sewage sludge, demonstrating its reliable performance.     

Standard reference materials (SRMs) for determination of organic contaminants in environmental samples

For the past 25 years the National Institute of Standards and Technology (NIST) has developed certified reference materials (CRMs), known as standard reference materials (SRMs), for determination of organic contaminants in environmental matrices. Assignment of certified concentrations has usually been based on combining results from two or more independent analytical methods. The first-generation environmental-matrix SRMs were issued with certified concentrations for a limited number (5 to 10) of polycyclic aromatic hydrocarbons (PAHs) and polychlorinated biphenyls (PCBs). Improvements in the analytical certification approach significantly expanded the number and classes of contaminants determined. Environmental-matrix SRMs currently available include air and diesel particulate matter, coal tar, marine and river sediment, mussel tissue, fish oil and tissue, and human serum, with concentrations typically assigned for 50 to 90 organic contaminants, for example PAHs, nitro-substituted PAHs, PCBs, chlorinated pesticides, and polybrominated diphenyl ethers (PBDEs). Electronic supplementary material Supplementary material is available in the online version of this article at and is accessible for authorized users.     

Certified reference materials to support a European thematic strategy for soil protection: the EUROSOILS (IRMM-443) experience

The recent proposal of thematic strategy for soil protection by the European Commission outlines that knowledge of problems associated with soil has increased considerably based on surveys, monitoring systems and data networks. Although this information is very useful, its value for the policy-making process is limited due to a lack of comparability. From this unsatisfying situation the need arises to develop an EU-wide monitoring system accompanied by suitable matrix reference materials. Experiences gained from the development and certification of IRMM-443 (The EUROSOILS) show how to approach the complex problem of providing suitable (i.e. representative) soil CRMs for the arising analytical needs to support existing and upcoming EU legislation.This paper presents briefly the quantitative findings of a certification exercise (adsorption coefficients for atrazine, lindane and 2,4-D, as well as pH in suspension). A comparison of these results with those of an intercomparison exercise organised in 1989 by the German UBA on very similar soils shows the significant improvement in the determination of soil adsorption coefficients that was induced by the EUROSOIL project. Indicative values of total and organic carbon content and nitrogen according to ISO Standards are also presented.Furthermore, the idea of reference soils and derived reference materials (for analytical purposes) as well as reference matrices (substrates for ecotoxicological testing) is highlighted and set into the context of horizontal standardisation of methods.     

The carbon nanotubes-based materials and their applications for organic pollutant removal:A critical review

The carbon nanotubes(CNTs) as the emerging materials for organic pollutant removal have gradually become a burgeoning research field.Herein,a mini-review of CNTs-based materials curre ntly studies for organic pollutant elimination is presented.This review summarizes the preparation methods of CNTsbased materials.CNTs-based materials can be used as adsorbents to remove organic pollutants in wastewater.The adsorption mechanisms mainly include surface diffusio n,pore diffusion and adsorption reaction.Most importantly,an in-depth overview of CNTs-based materials currently available in advanced oxidation processes(AOPs) applications for wastewater treatment is proposed.CNTs-based materials can catalyze different oxidants(e.g.,hydrogen peroxide(H_2 O_2),persulfates(PMS/PDS),ozone(O_3) and ferrate/permanganate(Fe(Ⅵ)/Mn(Ⅶ)) to generate more reactive oxygen species(ROS) for organic pollutant elimination.Moreover,the possible reaction mechanisms of removing organic pollutants by CNTs-based materials are summarized systematically and discussed in detail.Finally,application potential and future research directions of CNTs-based materials in the environmental remediation field are proposed.     

Certified reference materials for the quality control of EDTA- and acetic acid-extractable contents of trace elements in sewage sludge amended soils (CRMs 483 and 484)

 The ecotoxicity and mobility of trace elements in soils are often evaluated through analytical results resulting from operationally-defined determinations (single and sequential extractions), e.g. based on EDTA, acetic acid etc. extractions. The significance and comparability of these results is highly dependent on the procedures used (standardized protocols or standards adopted by international bodies) and their quality control relies on the availability of reference materials certified following these strictly applied procedures. Recognizing the need to harmonize some of the extraction schemes currently used for soil analysis, the Measurements and Testing Programme (formerly BCR) has organized a series of interlaboratory studies, the first aim of which was to evaluate EDTA- and acetic acid-extraction procedures and the second objective was to certify reference materials for their extractable trace element contents. Two sewage amended soils have been prepared for this purpose, originating respectively from Scotland and Catalonia. This paper describes the preparation, homogeneity and stability studies, and gives an overview of the certification campaign. Received: 6 May 1996/Revised: 14 June 1996/Accepted: 27 June 1996     

An international interlaboratory study for the production of a sewage sludge certified reference material for routine use in inorganic quality control

Two existing interlaboratory schemes are used to certify a sewage sludge reference material. Data from the analysis (As, Cd, Cr, Cu, Pb, Hg, Ni and Zn) of the material using routine procedures, US EPA and Netherlands NEN, plus INAA and IDMS and an interlaboratory comparison in Eastern Europe have been examined. The Dutch results show significantly lower analytical results for As for the graphite furnace technique compared to HG-AAS, probably due to matrix-effects. The differences between the Dutch and USA results for Cr and Ni suggest that the USEPA 3050A digestion method for dissolution of the metals is less aggressive for this material compared to aqua regia destruction. For international comparability of analytical data it is essential to harmonize method dependent dissolution/extraction techniques. The preparation of reference materials which mimic real samples and certification by ILS result in useful materials for quality control.     

Challenges in preparing water-matrix reference materials for PAHs and pesticides: examples from SWIFT-WFD proficiency-testing schemes

In accordance with Article 8 of the European Union (EU) Water Framework Directive (WFD), EU Member States are required to establish monitoring programs for the quality of the surface water and the groundwater within each river-basin district. As such data are the basis for regulatory decisions and measures required to achieve WFD environmental objectives, appropriate analytical quality-assurance and quality-control tools have to be implemented by the monitoring laboratories. In this respect, reference materials (RMs) play a key role. Within the framework of the SWIFT-WFD project (Screening methods for Water data InFormation in support of the WFD), several approaches to the preparation of matrix RMs for the analysis of polycyclic aromatic hydrocarbons and pesticides in water have been used in wide-scale proficiency-testing (PT) schemes. We present the different strategies employed in preparing water-matrix RMs for organic analytes. By reviewing the results from the SWIFT-WFD PT schemes, we reflect on the applicability and the suitability of the different approaches.     

Development and validation of a method for analyzing polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans in sewage sludge samples

Summary A method has been developed for the analysis of polychlorinated dibenzo-p-dioxins (PCDD) and dibenzofurans (PCDF) in sewage sludge samples. It was found that PCDD/F are best Soxhlet extracted from the matrix with toluene for 24h, after having tested other solvents (dichloromethane and hexane/acetone 41/59) and other extraction times. Several clean up steps (sulfuric acid, multilayer silica and Florisl columns) and concentration are required prior to analysis of the extract by high resolution gas chromatography-high resolution mass spectrometry (HRGC-HRMS). The complete procedure has been validated and the accuracy and precision data (repeatability and reproducibility) are given. The method is linear in the range studied and the limit of detection ranges between 0.2 and 2.2 pg g⁻¹ of dry matter for the 2,3,7,8-substituted congeners. Moreover, the suitability of the method has been checked in an international interlaboratory comparison. The successful application of this method to several samples from Catalan and Dutch urban wastewater treatment plants was demonstrated.     

Development of a matrix solid-phase dispersion method for the determination of polycyclic aromatic hydrocarbons in sewage sludge samples

A new, single-step extraction and purification method based on matrix solid-phase dispersion (MSPD) was developed to determine 17 polycyclic aromatic hydrocarbons (PAHs) in sewage sludge samples. The MSPD method consists of sample homogenisation, exhaustive extraction and clean-up by a single process. The different operational parameters of the method, such as the type of dispersant, type and amount of additives, clean-up co-sorbent and extractive solvent were evaluated. Reversed-phase (C18) and polymeric (Oasis HLB and Oasis MAX) materials, as well as normal phase sorbents (Florisil, silica, neutral alumina) and an inert support (sand) were tested to assess the sorbents effect on the yield and selectivity of the MSPD process. Analysis of extracts was performed by high performance liquid chromatography (HPLC) coupled with fluorescence detection.Quantification limits obtained for all of these considered compounds (between 0.0001 and 0.005 μg g⁻¹ dry mass) were well below of the limits recommended in the EU. The extraction yields for the different compounds obtained by MSPD ranged from 76.3% to 103.6%. On the other hand, the extraction efficiency of the optimised method is compared with that achieved by microwave-assisted extraction and the method was applied to the analysis of real sewage sludge samples. A certified reference material (sewage sludge (BCR 088)) and a reference material (sewage sludge (RTC-CNS312-04)) were used to validate the proposed method.     

Polycyclic aromatic hydrocarbons in waste waters and sewage sludge: Extraction and clean-up for HPLC analysis with fluorescence detection

Summary A modified solid-phase extraction technique using sonication of the adsorbent material instead of the elution normally applied has been compared with two conventional liquid-liquid extraction procedures for the determination of the 16 EPA PAHs in municipal waste waters by means of HPLC coupled with fluorescence detection. Liquid-liquid extraction with cyclohexane proved to be the most efficient and simplest procedure. Clean-up of the waste-water extracts was not considered necessary, because of the high chromatographic resolution of the column and the selectivity of the fluorescence detector. Different organic solvents were also compared for ultrasonic extraction of PAHs from sewage sludge. The best results were obtained by use of acetonitrile. Clean-up of sewage-sludge extracts was not found necessary for accurate quantification of the major PAH components with fluorescence detection. The precision of the whole analytical procedure from extraction to the final determination of PAHs was satisfactory for both waste-water and sewage-sludge samples.     

Redox flow batteries for energy storage: Recent advances in using organic active materials

The development of redox electrolytes using organic active materials as alternatives to metal-based species for redox flow batteries is booming recently. However, challenges and gaps remain toward commercialization. This review briefly discusses the most recent advances of using electroactive organic materials. Strategies such as chemical modification through molecular engineering and new efforts toward energy-rich electrolytes and high-power electrolytes are addressed. Furthermore, the limiting factors governing the cycling life are summarized.     

Application of BaTiO3-based catalysts for piezocatalytic,photocatalytic and piezo-photocatalytic degradation of organic pollutants and bacterial disinfection in wastewater: A comprehensive review

The coupling of piezocatalysis and photocatalysis known as piezo-photocatalysis has attracted a lot of attention as one of the most effective advanced oxidation process (AOPs) for wastewater treatment, especially for the degradation of organic pollutants and disinfection of microbes. To advance this technology, there’s a need to develop lead free piezoelectric materials to drive both piezocatalytic and photocatalytic process to prevent secondary pollution due to lead toxicity. Hence, barium titanate (BaTiO₃) has been widely used as lead free piezoelectric material for several applications including water splitting, bacterial disinfection, and wastewater treatment due to its exceptional optical and piezoelectric properties. This work presents a comprehensive review on the application of BaTiO₃ as a promising lead-free piezo-photocatalyst for the catalytic degradation of organic pollutants and bacterial disinfection from aqueous solution. This review article details the optical and piezoelectric properties, modification strategies, and synthetic methods of BaTiO₃. Furthermore, the application of BaTiO₃ as a preferred piezo-photocatalyst for wastewater treatment and a future perspective is presented.     

Development and validation of a rapid and wide-scope qualitative screening method for detection and identification of organic pollutants in natural water and wastewater by gas chromatography time-of-flight mass spectrometry

In this work, a multiclass screening method for organic contaminants in natural and wastewater has been developed and validated for qualitative purposes, i.e. to ensure the reliable and sensitive identification of compounds detected in samples at a certain level of concentration. The screening is based on the use of GC-TOF MS, and the sample procedure involves solid phase extraction with C(18) cartridges. Around 150 organic contaminants from different chemical families were investigated, including PAHs, octyl/nonyl phenols, PCBs, PBDEs and a notable number of pesticides, such as insecticides (organochlorines, organophosphorus, carbamates and pyrethroids), herbicides (triazines and chloroacetanilides), fungicides and several relevant metabolites. Surface water, ground water and effluent wastewater were spiked with all target analytes at three concentration levels (0.02, 0.1 and 1 μg/L). Influent wastewater and raw leachate from a municipal solid waste treatment plant were spiked at two levels (0.1 and 1 μg/L). Up to five m/z ions were evaluated for every compound. The identification criterion was the presence of, at least, two m/z ions at the expected retention time, measured at their accurate mass, and the accomplishment of the Q/q(i) intensity ratio within specified tolerances. The vast majority of compounds investigated were correctly identified in the samples spiked at 1 μg/L. When analyte concentration was lowered down to 0.1 μg/L the identification was more problematic, especially in complex-matrix samples like influent wastewater. On the contrary, many contaminants could be properly identified at the lowest level 0.02 μg/L in cleaner matrices. The procedure was applied to the screening of water samples of different origin and matrix composition and allowed the detection of several target contaminants. A highly reliable identification could be carried out thanks to the sensitive full-spectrum acquisition at accurate mass, the high selectivity reached with the use of narrow-mass window extracted ion chromatograms, the low mass errors observed in the positive detections and the Q/q ratio accomplishment.     

Hollow fiber liquid phase microextraction as a preconcentration and clean-up step after pressurized hot water extraction for the determination of non-steroidal anti-inflammatory drugs in sewage sludge

A method for the quantitative determination of non-steroidal anti-inflammatory drugs (NSAIDs) in sewage sludge was developed and validated. The target compounds were extracted using pressurized hot water extraction (PHWE) and then purified and preconcentrated by three-phase hollow fiber liquid phase microextraction (HF-LPME) followed by LC–ESI-MS analysis. The PHWE was optimized with regard to the pH of solvent as well as other operational parameters. The optimum conditions were 0.01 M NaOH as the extraction solvent, temperature of 120 °C, pressure of 100 bar, static time 5 min, 5 cycles, flush volume 90% and purge time 60 s. Spike recoveries for sludge samples spiked at 200 ng g⁻¹ were in the range of 101–109% but for the native drugs in non-spiked sludge samples, recoveries were 38.9%, 59.8%, 90.3% and 47.8% for ketoprofen, naproxen, diclofenac and ibuprofen, respectively. Donor phase pH, ionic strength and extraction time were optimized for HF-LPME after PHWE. The optimum conditions were 2 h extraction at pH 1.5 without salt addition. Enrichment factors in the range of 947–1213 times were achieved (extraction recoveries were 23.6–30.3%) for HF-LPME after PHWE. The matrix effect on the ionization of drugs in LC–ESI-MS was also investigated. The results show that there is a smaller matrix effect (−8.9% to +14.6%) in comparison with other published values obtained using solid phase extraction (SPE) for clean-up after pressurized liquid extraction (PLE). Method detection limits (MDLs) and method quantification limits (MQLs) for different drugs were in the range of 0.4–3.7 ng g⁻¹ and 1.5–12.2 ng g⁻¹ in dried sludge samples, respectively. The characteristics of the proposed method were compared with those of other published works. The considerably lower ion suppression/enhancement and minimum use of organic solvents (a few microliters of di-n-hexyl ether) in the sample preparation step are two highlighted advantages of the proposed method in comparison with previously published works. The method was applied to determine NSAIDs in sewage sludge from Källby wastewater treatment plant (Lund, Sweden) in April, June, August and October 2010. The highest concentration level was recorded for ibuprofen in the April sewage sludge sample (588 ng g⁻¹) and all of the selected NSAIDs were detected in all the samples analyzed.     

Molecular characterization of organically-bound sulfur in crude oils. A feasibility study for the application of Raney Ni desulfurization as a new method to characterize crude oils

Five crude oils with varying sulfur contents (0.1 – 4.7%) were characterized on a molecular level for organically-bound sulfur. Aromatic fractions were analyzed by GC-(MS) and asphaltene and polar fractions were analyzed by flash pyrolysis-GC-(MS). The polar fractions were also desulfurized with Raney Ni and the hydrocarbons formed were analyzed by GC-MS. Major sulfur compounds in the aromatic fractions were identified as alkylbenzo- and alkyldiben-zothiophenes. The flash pyrolyzates of the asphaltene contained alkylthiophenes and alkylbenzothiophenes as major compounds, depending on the thermal maturity of the oil. Generally, the sulfur-rich crude oils contained relatively more sulfur compounds. The flash pyrolyzates of polar fractions contained a variety of sulfur compounds (alkylthiolanes, alkylthianes, terpenoid sulfides, alkylbenzothiophenes) with substantial differences between different crude oils. Raney Ni desulfurization of the polar fraction yielded hydrocarbons dominated by n-alkanes, but isoprenoid alkanes, n-alkylcyclohexanes, mid-chain methylalkanes, tricyclic terpanes, hopanes and steranes were also present. These hydrocarbons show a potential to fingerprint crude oils since their distribution patterns are more characteristic than those of the hydrocarbons present in the saturated hydrocarbon fraction.     

Certified reference material for analytical quality assurance of minor and trace elements in food and related matrixes based on a typical Japanese diet: interlaboratory study

A Certified Reference Material (CRM) was prepared at the National Institute for Environmental Studies (NIES), Japan, in collaboration with the National Institute of Radiological Sciences (NIRS), Japan, for the analytical quality assurance of minor and trace elements in food and related matrixes. The starting material for the CRM was all food served in 29 households in Japan over two 3-day periods in 1997-1998, and thus the CRM represented a typical Japanese diet. All foods (meals, snacks, and beverages) were homogenized, freeze-dried, pulverized, blended, dispensed into 1,100 bottles, and sterilized. The within- and between-bottle homogeneity of the prepared CRM was satisfactory for most of the elements. The concentrations of 14 elements (Na, Mg, K, Ca, Mn, Cu, Zn, As, Se, Sr, Cd, Sn, Ba, and U) were certified based on a collaborative analysis involving NIES, NIRS, and 20 other laboratories. Reference values were given for the concentrations of 12 additional elements (P, Cl, Fe, Co, Ni, Br, Rb, Mo, I, Cs, Pb, and Th). The elements certified and those given reference values include minerals, essential trace elements, contaminant elements, and long-lived radionuclides. Thus, this CRM is of practical value in the quality assurance of element analysis of foods and diets in nutritional, environmental, and radiological research.     

The use of FT-NIR for API content assay in organic solvent media: a single calibration for multiple downstream processing streams

The use of near infrared spectroscopy (NIRS) in downstream solvent based processing steps of an active pharmaceutical ingredient (API) is reported. A single quantitative method was developed for API content assessment in the organic phase of a liquid–liquid extraction process and in multiple process streams of subsequent concentration and depuration steps. A new methodology based in spectra combinations and variable selection by genetic algorithm was used with an effective improvement in calibration model prediction ability. Root mean standard error of prediction (RMSEP) of 0.05 in the range of 0.20–3.00% (w/w) was achieved. With this method, it is possible to balance the calibration data set with spectra of desired concentrations, whenever acquisition of new spectra is no longer possible or improvements in model's accuracy for a specific selected range are necessary. The inclusion of artificial spectra prior to genetic algorithms use improved RMSEP by 10%. This method gave a relative RMSEP improvement of 46% compared with a standard PLS of full spectral length.