The role of spin-spin interaction in the electrical conductivity of vanadium phosphate glasses

Representative glass series of different vanadium content and valence state have been studied with special emphasis on V⁴⁺−V⁴⁺ spin-spin interaction. From temperature dependent EPR studies paramagnetic Curie temperatures and J values have been determined. We demonstrate that this method is informative in the whole glass formation range. It is shown that there is an antiferromagnetic → ferromagnetic transition at c = V⁴⁺/(V⁴⁺ + V⁵⁺) 0.17 (2.3×10²¹ spin cm⁻³). At this composition the glass is essentially homogeneous and displays maximal conductivity. In glasses of higher V⁴⁺ content, in which the dominating interaction is ferromagnetic, the conductivity gradually decreases. Therefore, ferromagnetically coupled V⁴⁺ − V⁴⁺ pairs seem to contribute to conductivity less effectively.     

Compositional dependence of the valency state of Cr ions in oxide glasses

Absorption spectra of Cr ions in multi-component oxide glasses melted in Ar were measured. The integrated extinction coefficient is used as a parameter to analyze the redox reaction of Cr³⁺ and Cr⁶⁺ in glass samples. The relative content of Cr⁶⁺ increased and that of Cr³⁺ decreased with increasing basicity in silicate and borate glasses; this result is consistent with previous studies. On the contrary, only Cr³⁺ exist in phosphate glasses. Cr⁴⁺ ions were found only in aluminate, gallate and alumino-silicate glasses with modifier contents ≥ 60 mol%. The relationship between point defects and Cr⁴⁺ formation is examined on the basis of electron spin resonance measurements. We concluded that the superoxide ion radical (O₂⁻) and the peroxy bonding (-O-O-) oxidize Cr³⁺ to Cr⁴⁺ in aluminate, gallate, and alumino-silicate glasses.     

Structure and properties of the pure and Pr-doped Ge25Ga5Se70 and Ge30Ga5Se65 glasses

The Ge₂₅Ga₅Se₇₀ and Ge₃₀Ga₅Se₆₅ pure and Pr³⁺-doped glasses were prepared by direct synthesis from elements and PrCl₃. It was found that up to 1 mol% PrCl₃ can be introduced in the Ge₂₅Ga₅Se₇₀ and Ge₃₀Ga₅Se₆₅ glasses. Both types of glasses with overstoichiometric and substoichiometric content of Se were homogeneous and of black color. The optical energy gap is E^opt_g=2.10 eV, and the glass transition temperature is T_g=543 K for Ge₂₅Ga₅Se₇₀ and T_g=633 K for Ge₃₀Ga₅Se₆₅. The long-wavelength absorption edge is near 14 μm and it corresponds to multiphonon processes. Doping by Pr³⁺ ions creates absorption bands in transmission spectra, which can be assigned to the electron transitions from the ground ³H₄ level to the higher energy levels of Pr³⁺ ions ³H₅, ³H₆, ³F₂, ³F₃ and ³F₄, respectively. By excitation with YAG:Nd laser line (1064 nm), two intense luminescence bands (1343 and 1601 nm) were excited. The first band can be ascribed to electron transitions between ¹G₄ and ³H₅ energy levels of Pr³⁺ ions. Full width at half of maximum (FWHM) of the intensity of luminescence was found to be 70 nm for (Ge₂₅Ga₅Se₇₀)_1 − x(PrCl₃)_x and (Ge₃₀Ga₅Se₆₅)_1 − x(PrCl₃)_x glasses. The FWHM in selenide glasses is lower than in halide and sulphide glasses. The second luminescence band (1601 nm) can be probably ascribed to the transitions between ³F₃ and ³H₄ energy levels of Pr³⁺ ions. The absorption and luminescence spectra of Pr³⁺ ions in studied glasses are slightly influenced by stoichiometry of glassy matrix. The Raman spectra of studied glasses were deconvoluted and assignment of Raman bands to individual vibration modes of basic structural units was suggested. The structure of studied glasses is mainly formed by corner-sharing and edge-sharing GeSe₄ tetrahedra. The vibration modes of Ga-containing structural units were not found, they are apparently overlapping with Ge-containing structural units due to small difference between atomic weights of Ge and Ga. In the glasses with substoichiometry of Se, the Ge–Ge bonds of Ge₂Se₆ structural units were found. In Se-rich glasses the Se–Se vibration modes were found. In all studied glasses also ‘wrong' bonds between like atoms were found in small amounts. Maximum phonon energy of studied glasses is 320 cm⁻¹.     

Optical third-harmonic generation from some high-index glasses

Optical third-harmonic generation from some high-index glasses was investigated. The highest χ⁽³⁾ was obtained from As₂S₃ glass 2.2 × 10⁻¹² esu/ This value was 100 times higher than that of pure SiO₂ glass and comparable with that of the polymer with monomer-doping, which are known as organic materials with quite high χ⁽³⁾. From the relationship between χ⁽³⁾ and composition, sulfide glasses were found to have higher χ⁽³⁾ than oxide or semiconductor-doped oxide glasses with similar refractive indices.     

Homogeneous line width in a zinc borate glass activated by Eu

In this work we report on the temperature depedence of the homogeneous line width (Γ_h) in 4ZnO · 3B₂O₃:Eu³⁺ glass in the region between 30 K and room temperature. The time resolved resonant fluorescence line narrowing technique was applied to the ⁷F₀ ↔ ⁵D₀ transition of Eu³⁺. We obtain that Γ_h follows the commonly found behaviour T² in the whole range of temperature (30–300 K). The Γ_h is comparable to that measured in borate glasses with a small amount of network modifier. This result, together with a linear increase of Γ_h with the excitation energy within the inhomogeneous profile, is indicative of a specific local environment around the Eu³⁺ ion in the zinc borate glass.     

Ionic transport and defect structure of vitreous beryllium fluoride

Vitreous BeF₂ was prepared by two techniques; (1) remelting of a technical grade material, and (2) vacuum distillation/fluoridation. Infrared spectroscopy studies have established that the first material contains about 0.5 wt.% hydroxyl, predicted to be coherently incorporated into the vitreous network as edge-linked [Be(OH)₄]²⁻ units. The distilled BeF₂ is water-free. The dc electrical conductivity of the remelted BeF₂ was measured as σ = (7.9 × 10³/T) exp(−24500 cal/mol/RT) ω⁻¹ cm⁻¹ and for the distilled BeF₂ as σ = (3.0 × 10⁵/T) exp(−36700 cal/mol/RT ω⁻¹ cm⁻¹ at temperatures to 280°C. Ionic transport studies utilizing a dc electrolysis polarization technique with N₂−F₂ and H₂−HF gas electrodes have demonstrated that the fluorine ion is the transport species. A general model for fluorine transport is proposed based upon a modified anti-Frenkel defect model. The difference in the fluorine transport process for the undistilled grade of BeF₂ is seen as a consequence of the anti-Frenkel defect pair interaction with the [Be(OH)₄[²⁻ groupings.     

Li conductivity in lithium niobate: silica glasses

Glasses of composition 65 mol% LiNbO₃:: 35 mol% SiO₂ have been shown to be Li⁺ ion conductors with a conductivity at 200°C > 1 × 10⁻⁵ (η cm)⁻¹ and an activation energy of 0.54 eV. The addition of approximately 0.1 mol% Fe₂O₃ leads to an enhancement of conductivity to ≈10⁻³ (η cm)⁻¹ at 200°C and an activation energy of 0.67 eV. The effect of Fe is shown to be in the control of microstructure in the glass, with Fe₂O₃ concentrations < 1 mol% acting as a grain growth inhibitors and larger concentrations acting as a nucleating agents. A model for this process based on the expected stoichiometry of the melt and the effect of Fe²⁺ and Fe³⁺ in charge compensation is in excellent agreement with experimental data from electron spin resonance.     

Water and the glass transition temperature of silicate melts

Literature data on the effect of water on the glass transition in silicate melts are gathered for a broad range of total water content c_w from 3 × 10⁻⁴ to 27 wt%. In terms of a reduced glass transition temperature T_g^*=T_g/T_g^GN, where T_g^GN is T_g of the melt containing c_w≈0.02 wt% total water, a uniform dependence of T_g^* on total water content (c_w) is evident for silicate melts. T_g^* decreases steadily with increasing water content, most strongly at the lowest water content where H₂O is dominantly dissolved as OH. For water-rich melts, the variation of T_g^* is less pronounced, but it does not vanish even at the largest water contents reported (≈27 wt%). T_g^* vs. c_w is fitted by a three-component model. This approach accounts for different transition temperatures of the dry glass, hydroxyl and molecular water predicting T_g^* as a weighted linear combination of these temperatures. The required but mostly unknown water speciation in the glasses was estimated using IR-spectroscopy data for hydrous sodium trisilicate and rhyolite.     

Changes in the refractive index of fused silica due to implantation of transition-metal ions

The changes in the refractive index of high purity silica glass produced by implantation of Ti⁺, Cr⁺, Mn⁺, Fe⁺ and Cu⁺ ions at 160 keV were measured using ellipsometry at a wavelength of 633 nm. Implantation doses ranged from 10¹⁵ to 6 × 10¹⁶ ions cm⁻². At the highest doses, a relative increase in refractive index of approximately 15% for implanted Cu ions and an increase of about half that for implanted Cr, Mn and Fe ions are observed. These variations in index probably result from colloid formation. For implanted Ti, virtually no change in the measured index of refraction was observed even at the highest doses.     

Dynamical properties of an alkali chloride mixture in the glassy and liquid states

Molecular dynamics calculations have been carried out to reveal the dynamical properties of an alkali chloride mixture (50 mol% LiCl---40KCl---10CsCl) and pure LiCl in the liquid and glassy states. It is found that the mobility of Li⁺ ions in the mixture is significantly lower than that in LiCl, not only in liquid state but also in the glassy state. The partial dynamic structure factors, S_Li---Li (Q, ω) and S_{Cl---Cl (Q, ω)}, are evaluated to investigate the dynamical correlation between the Li⁺ and Cl⁻ ions. In LiCl glass, it is shown that the motions of the Li⁺ and Cl⁻ ions are highly correlated with each other, and both the acoustic and optic modes are spatially delocalized (Q < 1.8 Å⁻¹). On the other hand, in the mixture glass, the motion of the Li⁺ ions is almost independent of that of the Cl⁻ ions, and at small wavelengths there are the intense vibrations localized on single Li⁺ ions similar to an Einstein oscillation.     

Ion-implanted treatment of (Ba,Sr)TiO3 films for DRAM applications

The effects of ion implantation on the properties of spin-on sol–gel Ba_0.7Sr_0.3TiO₃ (BST) thin films were studied by implanted Ar⁺, N⁺, and F⁺ doses. The F⁺-implanted BST samples present leakage current density <10⁻⁶ A/cm² at 2.5 V and dielectric constant 450. The leakage current of F⁺-implanted BST samples was reduced about one order of magnitude as compared with that of samples with implanted Ar⁺, N⁺ or without implantation. The thickness shrinkage from 135 to 115 nm was observed in F⁺-implanted BST films (before annealing treatment) and a respective increase in the refractive index from 1.84 to 2.05 was measured. After annealing the implanted samples, the changes of thickness and refractive index depend on the concentration of implanted dose. Based on an infrared transmission study of the samples we suggest that the ion-implanted samples with smaller dose (5×10¹⁴ cm⁻²) have fewer −OH contaminants than the non-implanted or implanted samples with the larger doses (1×10¹⁵ cm⁻²). Based on the results presented, we conclude that suitable ion implantation densifies the spin-on sol–gel BST films and reduces the −OH contaminants in the films.     

The vanadyl ion as a spectroscopic probe:: Measurement of optical basicity in the visible / near-infrared region

Previously optical basicity was always measured using s-p absorption spectra of Tl⁺, Pb²⁺ and Bi³⁺, but since these spectra are in the UV region, media containing oxides of transition metal aons have been excluded from such measurements. The present work shows that for VO²⁺ the d-d transition ²B₂ → ²E red-shifts with increasing optical basicity, and a study in the Na₂O---P₂O₅ glass system allows comparison with results obtained previously with Tl⁺ and other probe ions. It is shown that under controlled conditions determination of optical basicity with VO²⁺ is viable, and since the ²B₂ → ²E spectral band occurs in the visible / near-IR region, UV transparency of the medium is no longer necessary. The VO²⁺ probe therefore offers a means of obtaining optical basicities of glasses containing e.g. PbO, or of metallurgica slags containing e.g. Fe₂O₃ or MnO.     

Heavily carbon-doped p-type (In)GaAs grown by gas-source molecular beam epitaxy using diiodomethane

Heavily carbon-doped p-type In_xGa_1−xAs (0≤x<0.49) was successfully grown by gas-source molecular beam epitaxy using diiodomethane (CH₂I₂), triethylindium (TEIn), triethylgallium (TEGa) and AsH₃. Hole concentrations as high as 2.1×10²⁰ cm⁻³ were achieved in GaAs at an electrical activation efficiency of 100%. For In_xGa_1−xAs, both the hole and the atomic carbon concentrations gradually decreased as the InAs mole fraction, x, increased from 0.41 to 0.49. Hole concentrations of 5.1×10¹⁸ and 1.5×10¹⁹ cm⁻³ for x = 0.49 and x = 0.41, respectively, were obtained by a preliminary experiment. After post-growth annealing (500°C, 5 min under As₄ pressure), the hole concentration increased to 6.2×10¹⁸ cm⁻³ for x = 0.49, probably due to the activation of hydrogen-passivated carbon accepters.     

The effect of mixed alkaline earths on the diffusivity and the incorporation of iron in 5Na2O · xMgO · (15−x)CaO · yAl2O3 · (80−y)SiO2 melts

Diffusion coefficients of iron were measured in glass melts with the basic compositions 5Na₂O · xMgO · (15−x)CaO · yAl₂O₃ · (80−y)SiO₂ with x=5, 10 and y=0, 5, 7.5, 10 and 15. The melts were doped with 0.25 mol% Fe₂O₃ and studied in the temperature range from 1000 to 1600 °C using square-wave voltammetry. The voltammograms exhibited distinct peaks attributed to the reduction of Fe³⁺ to Fe²⁺, from which peak currents mixed diffusion coefficients of iron were calculated. Diffusion coefficients in all melt compositions which did not show crystallization could be fitted to Arrhenius equation. The diffusivities measured in different melt compositions were related to the same viscosity, i.e. not the same temperature. Increasing the alumina concentration from 5 to 10 mol% resulted in an increase of the viscosity corrected diffusivities. At further increasing alumina concentrations, the diffusivities get smaller again. This can be explained by the stabilizing effect of Na⁺ and Ca²⁺ on FeO⁻₄ and AlO⁻₄-tetrahedra, which strengthens the incorporation of Fe³⁺ into the glass structure.     

NdxLa2−xCaB10O19: Synthesis and characterization

Solid solutions of Nd_xLa_2−xcaB₁₀O₁₉ with different Na³⁺ concentration have been synthesized by substituting Nd ³⁺ for La³⁺ in La₂CaB₁₀O₁₉ Powder X-ray diffraction analysis shows that Nd³⁺ is easy to incorporate into the crystal. Single crystal nd_xLa_2−xCaB₁₀O₁₉ (NLCB) in centimeter size has been grown by Kyropoulos method. The crystal has strong absorption around 580nm and 805nm. The fluorescence spectra indicate that there is an energy transition at 1.06μm. And the SHG of NLCB is about the twice as that of KDP. These favorable features make NLCB a candidate for laser NLO multifunctional materials.     

Monte Carlo simulations of Meyer-Neldel effect on carrier time-of-flight in a-Si:H

We present Monte Carlo simulations of multiple-trapping transport with Meyer-Neldel effect in a-Si:H assuming exponential band tails. The transit time t_T, and the dispersion parameters, ₁ and ₂, before and after the transit time, are extracted from the simulated currents. The simulations show that including the Meyer-Neldel effect improves the agreement of ₁ and ₂ with experimental data, both at low and high temperatures and fits the time-of-flight drift mobility measurements. Best fits to the data yield T₀ = 263 K, T_{MN = 464 K}, v₀₀ = 5 × 10⁹ s⁻¹ and μ₀ = 4 cm² V⁻¹ s⁻¹ for electrons and T₀ = 409 K, T_{MN = 809 K}, v₀₀ = 6.5 × 10¹⁰ s⁻¹ and μ₀ = 0.5 cm² V⁻¹ for holes.     

Nuclear magnetic resonance studies of alkaline earth phosphosilicate and aluminoborosilicate glasses

The ¹¹B, ²⁷Al, ²⁹Si and ³¹P magic angle spinning (MAS) NMR spectra of MO–P₂O₅, MO–SiO₂–P₂O₅ and MO(M^′₂O)–SiO₂–Al₂O₃–B₂O₃ (M=Mg, Ca, Sr and Ba, M^′=Na) glasses were examined. In binary MO–P₂O₅ (M=Ca and Mg) glasses, the distributions of the phosphate sites, P(Q_n), can be expressed by a theoretical prediction that P₂O₅ reacts quantitatively with MO. In the ternary 0.30MO–0.05SiO₂–0.65P₂O₅ glasses, the 6-coordinated silicon sites were detected, whose population increases in the order of MgOxCaO–0.05SiO₂–(0.95−x)P₂O₅ glasses, its population increases with an increase in f (=([P₂O₅]−[MO]−[B₂O₃]−[Na₂O])/[SiO₂]) and has maximum at f=9. The signal due to the 5-coordinated silicon atoms is also observed when x is smaller than 0.45. When three network-forming oxides such as SiO₂, Al₂O₃ and B₂O₃ coexist, Al₂O₃ reacts preferably with MO. The populations of 4-coordinated boron atoms, N₄, are expressed well with r/(1−r), where r=([Na₂O]−[Al₂O₃])/([Na₂O]−[Al₂O₃]+[B₂O₃]). The correlation of the Raman signal at 1210 and 1350 cm⁻¹ with the NMR signal of Si(Q₆) at −215 ppm is also seen.     

Migration of Cu ions in Cu2O---Al2O3---SiO2 glasses on heating in air

The behavior of copper ions in the Cu₂O·Al₂O₃·4SiO₂ (in moles) glass on heating in air at temperatures up to 500°C was studied. When the glass, in which about 90% of Cu was present as Cu⁺ ions, was heated in air above 300°C, a CuO layer was formed on the surface. The amount of CuO was increased with heating temperature and time, corresponding to the decrease in weight of the glass. Furthermore, the fraction of Cu²⁺ ions in the glass increased. These observations suggest that oxygens do not diffuse into the glass, but Cu⁺ ions migrate to the surface from the interior to balance the surplus positive charge produced by the oxidation of Cu⁺ to Cu²⁺ ions inside the glass. The following reaction scheme for the formation of the CuO layer was proposed; 2Cu⁺(interior) + ₂¹O₂(surface) → Cu²⁺(interior) + CuO(surface).     

Silicate groupings in glassy and crystalline 2PbO·SiO2

The type and the amount of silicate groupings existing in glassy and crystalline 2PbO·SiO₂ have been determined by direct chemical methods: paper chromatography, trimethylsilylation combined with gas-liquid partition chromatography and by the molybdate method. The results obtained by these three different methods are in good agreement and demonstrate, that glassy 2PbO·SiO₂ and each of the three main crystalline polymorphs are characterized by its own specific silicate anion distribution: the distribution in vitreous 2PbO·SiO₂ is of a polyanionic nature; in T---Pb₂SiO₄ dimetic groups [Si₂O₇]⁶⁻ prevail; M₁---Pb₂SiO₄ contains predominantly [Si₄O₁₂]⁸⁻ rings and H---Pb₂SiO₄ is a typical polysilicate with chain anions [SiO₃²⁻]_n. The results fit a structural model according to which glass is a random array of discrete polyatomic groupings; the gradual transition from the glassy state to the stablest crystalline structure is connected with degradation and polymerization of silicate anions.     

Pb2+掺杂CaMoO4∶Dy3+,Eu3+荧光粉发光性能及能量传递机理的研究

采用共沉淀法合成了Pb²⁺掺杂CaMoO₄∶Dy³⁺,Eu³⁺荧光粉,通过X射线衍射仪、荧光分光光度计对荧光粉的物相组成、发光特性以及激活离子间能量传递效率进行了表征及分析。结果表明,掺杂Pb²⁺的CaMoO₄∶Dy³⁺,Eu³⁺荧光粉样品没有出现新的衍射峰,说明Pb²⁺很好地代替Ca²⁺进入到晶格当中,CaMoO₄∶0.05Dy³⁺,0.15Eu³⁺,0.15Pb²⁺荧光粉晶胞参数为a=b=0.548 9 nm, c=1.275 3 nm, Z=2,属于四方晶系,在391 nm波长激发下,484 nm处为Dy³⁺(⁴F_9/2→⁶H_15/2)的蓝光特征发射峰,575 nm处为Dy³⁺(⁴F_9/2→⁶H_13/2)跃迁产生的黄光发射峰,593 nm处为Eu³⁺(⁵D₀→⁷F₁)跃迁产生的橙光发射峰,619 nm处为Eu³⁺(⁵D₀→⁷F₂)跃迁产生的红光发射峰。通过计算得出CaMoO₄∶Dy³⁺,Eu³⁺荧光粉中Dy³⁺和Eu³⁺之间临界传递距离为1.542 6 nm,能量传递机理是偶极-四极相互作用,能量传递效率接近60.31%,掺杂金属离子Pb²⁺的荧光粉样品能量传递效率最高提升至72.40%。所以,掺杂Pb²⁺能够大幅度提升Dy³⁺与Eu³⁺之间能量传递效率和改善荧光粉的发光性能,因此其在白光LED领域具有重要研究意义。