硼、氮共掺杂多孔碳的制备及其超电容性能

分别以含氮菲咯啉、四硼酸钾和醋酸锌为碳源、活化剂和模板,制备了B、N共掺杂多孔碳(BN-PC),并探究模板质量对BN-PC结构和储电性能的影响。当醋酸锌质量为5g时,所得BN-PC₅中B、N杂原子含量分别为 20.21%、18.29%。电化学测试结果表明,以6 mol·L^-1 KOH为电解液,BN-PC₅电极展现出高的比电容(在0.05 A·g^-1电流密度下为255 F·g^-1)、优异的倍率性能(在20A·g^-1电流密度下为188F·g^-1)和卓越的循环稳定性(在5 A·g^-1的电流密度下循环10 000次比电容保持率为97%)。以3 mol·L^-1 ZnSO₄为电解液,在平均功率密度为56W·kg^-1时,BN-PC₅电容器的能量密度可达27Wh·kg^-1。     

盐酸和磺基水杨酸复合掺杂聚苯胺的热电性能

以苯胺为单体, 过硫酸铵为氧化剂, 采用化学氧化聚合法在盐酸和磺基水杨酸混合溶液中制备了导电聚苯胺。通过XRD、SEM、FTIR等分析手段, 对所得产物的结构进行研究, 并探讨在相同聚合条件下, 不同的磺基水杨酸和盐酸的物质的量浓度比(c_SSA:c_HCl)对聚苯胺热电性能的影响。结果显示, 混合酸掺杂聚苯胺的电导率随c_SSA:c_HCl的增加而增大, 但Seebeck系数的变化趋势却与之相反。当c_SSA:c_HCl=0.25:1时, 掺杂态聚苯胺的功率因子在175℃时达到最大值为0.46 μW·m^-1·K^-2,分别是相同条件下HCl和SSA掺杂聚苯胺的1.7和1.9倍。这表明适当配比的有机酸与无机酸混合掺杂比单一酸掺杂更有利于聚苯胺热电性能的提高。     

荧光导电聚合物β1-SiW11M/聚苯胺的固相合成及性质

用固相合成法，以Keggin结构过渡金属一取代杂多钨硅酸盐异构体β₁-[SiW₁₁M(H₂O)O₃₉]^6-(M=Mn²⁺，Co²⁺，Zn²⁺，Fe²⁺)为掺杂剂制备了6种聚苯胺掺杂材料。用元素分析、红外光谱、紫外光谱、荧光光谱、SEM、X-射线粉末衍射、热重分析等对此材料进行了表征，研究了它们的热稳定性和导电性。结果表明：掺杂了杂多钨硅酸盐异构体的聚苯胺最好的电导率为9.6 × 10^-2 S·cm^-1，聚苯胺微米棒的直径在100 nm。     

基于电纺丝法的In2O3/CdO复合材料的制备及甲醛气敏特性

用静电纺丝法制备了In(NO₃)₃/聚乙烯吡咯烷酮(PVP)纺丝前驱物, 然后分别在500、600、700℃时烧结得到三种In₂O₃ 纳米纤维. 通过X 射线衍射(XRD)仪、热重差热分析(TG/DTA)、场发射扫描式电子显微镜(FE-SEM)表征结果得知, 500℃时In₂O₃的晶相已经形成, 且粒径为最小, 约为24 nm, 纳米纤维呈介孔结构.将三种烧结温度的In₂O₃纤维制作成气敏元件, 测试对比了三种元件对甲醛气体的敏感特性, 结果表明, 500℃烧结得到的In₂O₃纳米纤维在工作温度为240℃时响应最好, 对浓度为10×10^-6 (体积分数, φ)甲醛的响应为7.用静电纺丝法合成了CdO 纳米颗粒, 通过XRD、SEM 表征得知CdO 呈粒径约为68 nm 的颗粒. 将In₂O₃和CdO以不同摩尔比(1:1, 10:1, 20:1)复合, 对比测试了纯In₂O₃及三种In₂O₃/CdO复合材料对应的气敏元件对甲醛的气敏特性, 测试结果表明当In₂O₃纳米纤维与CdO纳米颗粒以摩尔比10:1 复合时, 元件的工作温度较低(200℃), 且对甲醛表现出最佳的气敏特性, 对浓度为10×10^-6甲醛的响应为13.6, 响应/恢复时间为140 s/32s. 最后对不同摩尔比复合的In₂O₃/CdO对甲醛的气敏机理进行了初步分析.     

以多层次聚苯胺颗粒为电极活性物质的超级电容器的电化学性能

以(NH₄)₂S₂O₈为氧化剂用化学氧化法合成了具有多层次结构的聚苯胺颗粒，其二次颗粒由一次颗粒集结而成，一次颗粒的粒径基本上在1 μm以下，一次颗粒由多层微小薄片叠合而成. 用这种聚苯胺为活性物质制成电极，以2 mol•L^-1的H₂SO₄水溶液作电解液，组装成了聚苯胺电极超级电容器. 用循环伏安法、电化学阻抗谱和恒电流充放电技术测试了该超级电容器的电化学性能.在7 mA的充放电电流下，它的比能量可达6.35 Wh•kg^-1，比功率可达132 W•kg^-1，电极材料的比容量可达408 F•g^-1. 在20 mA的充放电电流下，它的比能量可达4.39 Wh•kg^-1，比功率可达328 W•kg^-1，电极材料的比容量可达324 F•g^-1. 在100次的充放电循环中，聚苯胺电极超级电容器的电容量没有下降，电荷充放电效率一直保持在95%左右.     

泡沫镍负载的NiCo2O4纳米线阵列电极的超级电容性能

采用无模板自然生长法制备了泡沫镍支撑的NiCo₂O₄纳米线阵列电极, 利用扫描电镜(SEM)和透射电镜(TEM)观测了纳米线的表面形貌, 利用X射线衍射(XRD)分析了纳米线的结构, 通过循环伏安、恒流充放电和交流阻抗测试了电极的超级电容性能. 结果表明: NiCo₂O₄纳米线直径约为500-1000 nm、长度约为10 μm, 垂直且密集地生长在泡沫镍骨架上. 纳米线阵列电极的放电比容量高达741 F·g^-1, 循环420次后比容量仍保持在655 F·g^-1, 电化学阻抗测试其电荷传递电阻仅为0.33 Ω, 420次循环后电荷传递电阻仅增加0.06 Ω.     

聚合时间对染料敏化太阳能电池中聚苯胺对电极结构和性能的影响

采用恒电压方法, 以掺杂氟的SnO₂ (FTO)导电玻璃为基底, 采用不同的聚合时间制备SO₄^2?掺杂的聚苯胺对电极(PANI CEs). 利用扫描电子显微镜(SEM)、紫外-可见(UV-Vis)吸收光谱、循环伏安法(CV)和电化学阻抗谱(EIS)等技术详细研究了聚合时间对PANI CEs的表面形貌、结构(如掺杂度、共轭性、氧化态等)和对I^?/I^3?的催化活性的影响. SEM结果表明PANI在FTO上的生长分两个阶段. 适当增加聚合时间可以增加PANI CEs的比表面积, 为催化I^?/I^3?反应提供更多的活性位点, 同时聚苯胺链的共轭性、半氧化态聚苯胺(EB)结构的含量和对阴离子SO₄^2?的掺杂度会随着增加, 进而PANI 的导电率也逐渐增大. 然而, 聚合时间过长会引起薄膜厚度的增加和氧化结构的过多, 使PANI CEs的导电率降低, 电子在PANI 薄膜中的传输阻抗增加, 进而影响其对I^?/I^3?的催化性能. 聚合时间为300 s 时制备出的PANI 薄膜作为染料敏化太阳能电池(DSSCs)对电极和以D149 为染料时, 获得的最高电池光电转换效率为5.30%, 可达到基于Pt 对电极电池效率的88%. 因此, 通过电化学方法制备的PANI CEs有望代替贵金属Pt CEs用于DSSCs中.     

高比表面CexZr1-xO2复合氧化物的制备及表征

分别采用共沉淀法和阴离子表面活性剂模板法制备了Ce_xZr_1-xO₂复合氧化物。采用XRD、AFM、FTIR以及N₂吸附-脱附等方法对样品进行了表征。结果表明，共沉淀法合成的样品在500 ℃煅烧2 h后，生成了立方相Ce_0.75Zr_0.25O₂和四方相Ce_0.5Zr_0.5O₂固溶体，比表面积为62.1 m²·g^-1，孔体积为0.097 cm³·g^-1；以阴离子表面活性剂十二烷基苯磺酸钠(SDBS)为模板剂，乙二胺为助模板剂合成的样品在500 ℃煅烧2 h后，生成了纯四方相Ce_0.5Zr_0.5O₂固溶体，比表面积为180 m²·g^-1，孔体积为0.182 cm³·g^-1。结果表明，以阴离子表面活性剂SDBS为模板剂，可以合成高比表面积且具有介孔结构的Ce_0.5Zr_0.5O₂复合氧化物；加入乙二胺作为助模板剂可明显的提高比表面积和孔体积。     

γ-AlOOH/Al2O3修饰硅藻土的制备与Cs+、Pb2+吸附性能

以结晶氯化铝(AlCl₃·6H₂O)作为铝源,十二烷基苯磺酸钠(SDBS)为模板剂,采用水热法在硅藻土盘上制备了束状纳米结构γ-AlOOH/Al₂O₃复合吸附剂。采用XRD、SEM、TEM、TG/DSC、N₂吸脱附等对样品进行了表征。研究了样品对¹³³Cs⁺及Pb²⁺的吸附能力。研究表明,样品γ-AlOOH/硅藻土、γ-Al₂O₃/硅藻土,对Cs⁺及Pb²⁺均具有良好的吸附性能,两者对Cs⁺的去除率分别为98.9%和99.6%;对Pb²⁺的最大吸附量分别为357.1、416.7 mg·g^-1。两种样品对Pb²⁺的吸附均符合Langmuir吸附模型。     

层状Co3O4的制备及其电化学电容行为

以P123为模板水热合成制备了Co₂(OH)₂CO₃前驱体，200 ℃热处理后得到了具有层状结构的Co₃O₄。循环伏安、恒流放电等电化学测试表明，200 ℃所得Co₃O₄电极在6 mol·L^-1 KOH溶液中和-0.1～0.5 V(vs Ag/AgCl)电位范围内，具有较好的循环稳定性能，单电极比电容达到505 F·g^-1。     

多环芳二酐型聚酯亚胺膜的透气性能

多环芳二酐型聚酯亚胺膜的透气性能李悦生，丁孟贤，徐纪平（浙江大学高分子科学与工程研究所，杭州，３１００２７）（中国科学院长春应用化学研究所）关键词聚醚酰亚胺，聚酯酰亚胺，膜，透气性通常的聚酰亚胺加工性能较差，在芳环二酐的苯环间引入醚键等柔性基团后，其...     

微量元素与疾病诊断治疗的研究现状及展望

对国内外微量元素与疾病的关系及其诊断治疗的研究现状及研究动向进行了综述，包括：微量元素与地方病、癌肿、心血管病、糖尿病、眼病、神经系统病等。参考文献72篇。     

Determination and study on residue and dissipation of benazolin-ethyl and quizalofop-p-ethyl in rape and soil

A QuEChERS (quick, easy, cheap, effective, rugged, and safe) method for the determination of benazolin-ethyl and quizalofop-p-ethyl in rape and soil by high-performance liquid chromatography-tandem mass spectrometry has been developed in this study. The residue and dissipation of benazolin-ethyl and quizalofop-p-ethyl in rape and soil were determined with the developed method. The half-lives of benazolin-ethyl in rape straw and soil were 3.7–5.1 days and 14.3–26.3 days, respectively. The half-lives of quizalofop-p-ethyl in rape straw and soil were 5.0-6.1 days and 0.3–9.7 days, respectively. The residue of benazolin-ethyl and quizalofop-p-ethyl in rapeseed and soil were below the detection limit (i.e., 0.5?mg?kg^?1, the maximum residue level of European Union for quizalofop-p-ethyl).     

Synthesis and Optical and Redox Properties of Symmetric and Asymmetric BODIPYs

Herein, we present the synthetic route and the photophysical, electrochemical as well as laser properties of novel red‐emitting boron‐dipyrromethenes (BODIPYs) bearing arylethyne moieties. Such functionality is added along the main axis of the chromophore leading to single‐ and double‐substituted derivatives. The relationship between the dye structure and the lasing properties is studied in detail with the help of the photophysical and electrochemical properties as well as quantum mechanical simulations. The asymmetric substitution of the parent dye induces inhomogeneities in the charge distribution, which leads to an overall loss of the fluorescence capacity, mainly in polar media. Such non‐radiative deactivation processes can be softened by decreasing the electron‐donor ability of the substituent or even avoided by symmetrical substitution. Thus, grafting of the arylethyne moieties at the longitudinal axis of the indacene core results in an effective strategy to develop red‐edge BODIPYs with highly efficient and photostable laser emission.     

Ti-V基储氢合金及其氢化物的物相结构与组分优化设计

Ti-V基储氢合金在室温、常压下即可表现出良好的储氢特性,且质量储氢容量明显高于传统AB₅型储氢合金,从而在氢气的精制和回收、运输和储存及热泵等方面有较早的应用。 此外,在混合气体分离、核反应堆中处理氢的同位素、镍氢电池及燃料电池负极材料等方面也得到了广泛的研究与关注。 基于目前Ti-V基储氢合金的研究现状,概述了该类合金的优势、限制性因素(包括成因)及改性手段。 此外,为了进一步理解Ti-V基合金储氢机理、构建合金组分与储氢特性之间的对应关系,本工作重点围绕Ti-V基储氢合金及其氢化物的结构、组分优化设计展开综述,并对其未来研究方向做出展望。     

钒与糖代谢及糖尿病

微量元素钒作为生物体内必需元素，经证实有很重要的生理学功能，与机体糖代谢有十分密切的关系，且能降低糖尿病动物模型的高血糖，极有可能被开发为治疗糖尿病的药物。     

Conformations and steric and stacking interactions of trisubstituted ureas and thioureas with alkyl and phenyl groups

The monomeric ν(N—H) vibrations of various trisubstituted ureas of the R₂UPh type and -thioureas of the R₂TUPh type have been studied. The trans—out isomerism in the former and the trans—out—cis isomerism in the latter are discussed from the point of view of steric effect. The monomeric ν(N—H) vibrations of RPhUPh and RPhTUPh are also examined. The single band appearing in the spectrum of both ureas is characteristic of the cis form; this suggests the existence of phenyl—phenyl interaction (the stacking interaction proposed by Galabov et al. [10]). Behavior of ν(N—H) vibrations at several concentrations is shown to be clearly different in the three forms (trans, out and cis). The presence of the cis form is confirmed by solvent effect experiments.     

Synthesis of Tyrosol and Hydroxytyrosol Glycofuranosides and Their Biochemical and Biological Activities in Cell-Free and Cellular Assays

Tyrosol (T) and hydroxytyrosol (HOT) and their glycosides are promising candidates for applications in functional food products or in complementary therapy. A series of phenylethanoid glycofuranosides (PEGFs) were synthesized to compare some of their biochemical and biological activities with T and HOT. The optimization of glycosylation promoted by environmentally benign basic zinc carbonate was performed to prepare HOT α-L-arabino-, β-D-apio-, and β-D-ribofuranosides. T and HOT β-D-fructofuranosides, prepared by enzymatic transfructosylation of T and HOT, were also included in the comparative study. The antioxidant capacity and DNA-protective potential of T, HOT, and PEGFs on plasmid DNA were determined using cell-free assays. The DNA-damaging potential of the studied compounds for human hepatoma HepG2 cells and their DNA-protective potential on HepG2 cells against hydrogen peroxide were evaluated using the comet assay. Experiments revealed a spectrum of different activities of the studied compounds. HOT and HOT β-D-fructofuranoside appear to be the best-performing scavengers and protectants of plasmid DNA and HepG2 cells. T and T β-D-fructofuranoside display almost zero or low scavenging/antioxidant activity and protective effects on plasmid DNA or HepG2 cells. The results imply that especially HOT β-D-fructofuranoside and β-D-apiofuranoside could be considered as prospective molecules for the subsequent design of supplements with potential in food and health protection.     

Ferrocene and ferrocenium modified clays and their styrene and EVA composites

In this work, ferrocene- and ferrocenium-containing salts were employed to modify montmorillonite. X-ray measurements show an increase in the interlayer spacing upon clay modification, which means that the larger and more organophilic cations were inserted into the gallery space of montmorillonite. Attempts to prepare nanocomposites of polystyrene and ethylene vinyl acetate copolymers lead to immiscible systems; the morphology of these systems was elucidated with TEM, XRD and cone calorimetry. The thermal stability of the composites is greater than that of the virgin polymer.