Effect of support on activity of palladium catalysts in nitrobenzene hydrogenation

The effect of two types of catalysts on the activity of the catalytic hydrogenation of nitrobenzene was studied. Catalysts were prepared by the surface deposition of palladium hydroxide with a simultaneous reduction with formaldehyde in a basic environment and were characterised by X-ray powder diffraction, transmission electron microscopy, adsorption-desorption, and catalytic tests — hydrogenation of nitrobenzene in methanol. The influence of the supports’ (activated carbon and a mixture of activated carbon and multi-walled carbon nanotubes) surface area is discussed. Despite having a size comparable (4–5 nm) to crystallites of metallic palladium, the catalyst prepared on a mixture of activated carbon and nanotubes (Pd/C/CNT) was significantly less active than the catalyst prepared on pure activated carbon (Pd/C); the rate of this reaction was approximately 30 % lower than the initial reaction rate. This feature could be attributed to the lower specific surface area of the Pd/C/CNT (531 m² g^?1) in comparison with the Pd/C (692 m² g^?1).     

配位体对钯纳米催化剂的形成及其电活性的影响

分别在EDTA,甘氨酸(Gly)和木质素磺酸钠(Ls)存在下,以硼氢化钠为还原剂,将Pd²⁺还原为Pd纳米颗粒并负载在多壁碳纳米管(MWCNT)表面。采用扫描电镜(SEM),透射电镜(TEM)和X射线衍射(XRD)对纳米Pd催化剂的形貌和微结构进行了表征。结果表明:EDTA存在时,所形成的Pd纳米颗粒(Pd-EDTA/MWCNT)的粒径更小,在MWCNT上的分散度更高。采用循环伏安(CV)和计时伏安技术(CA),研究了催化剂在碱性环境中对乙醇的电催化活性。在碱性溶液中对乙醇氧化的电化学研究表明:在Pd-EDTA/MWCNT催化剂上,乙醇氧化反应的起始电位较低,电流密度最大,电子传递阻力较小,反应速率较大,并且对乙醇氧化的电催化活性保持稳定。     

Argon glow discharge plasma‐reduced palladium nanoparticles supported on activated carbon for Suzuki and Heck coupling reactions

Palladium nanoparticles supported on activated carbon were prepared by argon glow discharge plasma reduction (Pd/C‐P) without any chemical reducing agents and protective agents. The as‐prepared Pd/C‐P catalyst was characterized using nitrogen adsorption–desorption, X‐ray diffraction and transmission electron microscopy analyses. The results showed that the palladium nanoparticles reduced by plasma are well dispersed with a smaller particle size than commercial Pd/C. Pd/C‐P exhibited a high catalytic activity in Suzuki and Heck coupling reactions. Moreover, there was no obvious loss of catalytic activity even after eight repeated cycles, showing good reactivity and recyclability.     

DNA‐Directed Growth of Pd Nanocrystals on Carbon Nanotubes towards Efficient Oxygen Reduction Reactions

Unique DNA‐promoted Pd nanocrystals on carbon nanotubes (Pd/DNA–CNTs) are synthesized for the first time, in which through its regularly arranged PO₄^3? groups on the sugar–phosphate backbone, DNA directs the growth of ultrasmall Pd nanocrytals with an average size of 3.4 nm uniformly distributed on CNTs. The Pd/DNA–CNT catalyst shows much more efficient electrocatalytic activity towards oxygen reduction reaction (ORR) with a much more positive onset potential, higher catalytic current density and better stability than other Pd‐based catalysts including Pd nanocrystals on carbon nanotubes (Pd/CNTs) without the use of DNA and commercial Pd/C catalyst. In addition, the Pd/DNA–CNTs catalyst provides high methanol tolerance. The high electrocatalytic performance is mainly contributed by the ultrasmall Pd nanocrystal particles grown directed by DNA to enhance the mass transport rate and to improve the utilization of the Pd catalyst. This work may demonstrate a universal approach to fabricate other superior metal nanocrystal catalysts with DNA promotion for broad applications in energy systems and sensing devices.     

CNT表面修饰对Pt/CNT在邻氯硝基苯加氢反应中催化性能的影响

用乙二醇还原法制备了碳纳米管(CNT)负载的铂催化剂(Pt/CNT).考察了CNT化学修饰与物理修饰对催化剂的影响.CNT化学修饰采用H2SO4-HNO3氧化法,物理修饰采用十二烷基硫酸钠(SDS)吸附法.用X射线衍射、透射电子显微镜、电感耦合等离子发射光谱、H2程序升温脱附、傅里叶变换红外光谱和元素分析对Pt/CNT催化剂进行了表征,并以邻氯硝基苯选择加氢为探针反应考察了Pt/CNT的催化性能.结果表明,化学修饰与物理修饰都能在CNT表面引入一定数量的活性位,有助于促进Pt异相成核,提高Pt的分散性,进而提高催化剂的活性.SDS在一定浓度下可形成特定结构的胶束,导致形成特定形貌的Pt纳米粒子.     

碳纳米管负载Co-Mo催化剂在孤岛减压渣油加氢裂化反应中的应用

采用等体积浸渍法制备了一系列不同Co/Mo原子比的碳纳米管（CNT）负载Co Mo催化剂。将该系列催化剂用于孤岛减压渣油加氢裂化反应,评价其催化效果,并在相同反应条件下与 γAl2O3负载Co-Mo催化剂的催化性能进行比较。结果表明,Co-Mo/CNT催化剂的催化效果略低于Co-Mo/γAl2O3催化剂。Co/Mo原子比对Co-Mo/CNT催化剂的催化效果有较大的影响。与相同载体的催化剂相比,当Co/Mo原子比为0.50时,Co-Mo/CNT催化剂具有最佳的催化效果,而Co-Mo/γAl2O3催化剂在Co/Mo原子比为0.35时具有最佳的催化效果。     

Palladium supported on chitosan as a recyclable and selective catalyst for the synthesis of 2-phenyl ethanol

Two different chitosan supported palladium based catalysts were prepared, wherein dispersed palladium nanoparticles were obtained via chemical reduction supported on chitosan (Pd/CTS) and amine functionalized modified chitosan (Pd/AFCTS). The catalytic activity of the Pd-based catalysts, Pd/CTS and Pd/AFCTS, were assessed in the hydrogenation of styrene oxide to 2-phenyl ethanol. Both Pd-based catalysts enhanced the formation of the desired 2-phenyl ethanol in contrast to a conventional Pd/C catalyst without the assistance of inorganic or organic base. A considerable influence on the conversion and selectivity was observed in the case of Pd/AFCTS, consisting of palladium nanoparticles stabilized and dispersed on amine-functionalized chitosan matrix, affording complete conversion of styrene oxide with 98% selectivity to 2-phenyl ethanol. The catalyst Pd/AFCTS has also been recycled without significant loss of activity and selectivity.     

金掺杂对碳负载钯催化还原性能的促进作用

在许多催化应用中双金属的PdAu催化剂性能优于单金属催化剂.科研人员对具有可控纳米结构和高活性的PdAu催化剂进行了广泛的研究,但该催化剂的制备需要多步且通常步骤复杂.本文仅通过浸渍和焙烧制得了Au掺杂的负载型Pd催化剂,所得PdAu/C催化剂用于室温水相三氯乙烯加氢脱氯反应.当Pd和Au负载量分别为1.0 wt%和1.1 wt%时,在经过干燥、空气处理和H2还原的过程后，所制得的PdAu/C催化剂活性最高,初始转化频率(TOF)为34.0×10–2 molTCEmolPd–1 s–1,是单金属1.0 wt%Pd/C催化剂TOF (2.2×10–2 molTCEmolPd–1 s–1)的15倍以上. X射线吸收光谱结果表明,金的加入避免了400oC焙烧时Pd的氧化.本文还提出了可能的催化剂纳米结构演变路径,以解释所观察到的催化现象.     

Fabrication of Nitrogen‐Doped Mesoporous‐Carbon‐Coated Palladium Nanoparticles: An Intriguing Electrocatalyst for Methanol and Formic Acid Oxidation

Inspired by the attractive catalytic properties of palladium and the inert nature of carbon supports in catalysis, a concise and simple methodology for in situ nitrogen‐doped mesoporous‐carbon‐supported palladium nanoparticles (Pd/N‐C) has been developed by carbonizing a palladium dimethylglyoximate complex. The as‐synthesized Pd/N‐C has been exfoliated as a fuel cell catalyst by studying the electro‐oxidation of methanol and formic acid. The material synthesized at 400 °C,namely, Pd/N‐C‐400,exhibitssuperior mass activity and stability among catalysts synthesized under different carbonization temperaturesbetween300 and 500 °C. The unique 1D porous structure in Pd/N‐C‐400 helps better electron transport at the electrode surface, which eventually leads to about five times better catalytic activity and about two times higher stability than that of commercial Pd/C. Thus, our designed sacrificial metal–organic templatedirected pathway becomes a promising technique for Pd/N‐C synthesis with superior catalytic performances.     

Effects of Cerium Oxides on the Catalytic Performance of Pd/CNT for Methanol Oxidation

The carbon nanotubes supported palladium(Pd/CNT)nanocatalysts were modified by cerium oxides/ hydroxides and their catalytic performances for methanol oxidation were evaluated.Electrochemical measurements indicate that the introduction of cerium remarkably improves the catalytic activity of Pd/CNT catalysts towards methanol oxidation.X-Ray photoelectron spectra results reveal an interaction between palladium and cerium oxides.It is also observed that cerium-modified catalysts have excellent poison resistances,which is attributed to the poison-removal ability of cerium oxides/hydroxides.The highly oxidized cerium oxides/hydroxides have a strong ability to inhibit the accumulation of carbonaceous intermediates on the active sites of Pd catalysts.     

直流电电化学沉积镍制备原位生长碳纳米管化学修饰电极

利用直流电电化学沉积法将生长碳纳米管(CNT)的催化剂镍均匀地附着在石墨电极(GE)表面,再通过化学气相沉积法制备得到原位生长碳纳米管化学修饰电极(GSCNT-CME).电化学沉积的金属镍和所制备的修饰电极分别用光学显微镜、扫描电子显微镜(SEM)和电子能谱(EDX)进行表征,所得修饰电极的电化学性能用[Fe(CN)6]3-/[Fe(CN)6]4-溶液进行表征.结果表明:经直流电电化学沉积,可以在石墨电极表面沉积一层致密的金属镍,能生长出管径均匀的碳纳米管,所制得的修饰电极具有良好的电化学响应灵敏性和准确性,可在电化学检测领域发挥重要的应用.     

乙二胺功能化树脂负载Pd(0)配合物：可重复使用的高活性Heck芳基化催化剂

The ethylenediamine-functionalized resin-supported Pd(0)complex was prepared from PdCl_2 and ethylenedia-mine-functionalized chloromethylated polystyrene,followed by reduction with KBH_4.The complex was character-ized by FT-IR,XRD,BET,SEM and EDS.The resin-supported catalyst exhibited high catalytic activity in theHeck reaction and could be reused up to 17 times in NMP or 16 times in DMF at 90 ℃ in the Heck reaction of io-dobenzene with acrylic acid.The leaching investigation disclosed that the palladium leaching was caused by the in-teraction of iodobenzene with the metal Pd(0)on supported catalyst.The leached palladium species in filtrate wasvery stable and could be reused five times after the solid catalyst was filtered off.A cross-transfer test in recyclingin the presence of additional carbon disclosed that the soluble leached palladium species had much higher catalyticactivity than supported and/or adsorbed palladium in solid-solution heterogeneous Heck reaction.     

Fe/Cu修饰氮掺杂碳纳米管的构筑及催化性能

通过简单的原位化学合成法结合离子交换法制备了Cu修饰氮掺杂碳（Cu-N-C）和Fe/Cu修饰氮掺杂碳纳米管（Fe/Cu-N-C/CNT）,并系统评估了2种催化剂作为染料敏化太阳能电池（dye-sensitized solar cells,DSSCs）对电极在I₃^-/I^-体系中的电化学特性和光伏性能。采用X射线衍射（XRD）、拉曼（Raman）、X射线光电子能谱（XPS）和场发射扫描电镜（FESEM）对合成的催化剂进行组分和形貌表征。结果表明：纳米管状的Fe/Cu-N-C/CNT的石墨化程度比纳米颗粒状的Cu-N-C更高,更有利于I₃^-还原反应中电荷的传输。光伏性能测试结果表明：基于Fe/Cu-N-C/CNT对电极的DSSCs的光电能量转换效率（power conversion efficiency,PCE）达到7.55%,高于相同测试条件下Cu-N-C（6.99%）和Pt（6.76%）对电极的PCE。50圈连续循环伏安测试结果表明：Fe/Cu-N-C/CNT催化剂具有比Cu-N-C更好的电化学稳定性。     

Carbon nanotube growth on high modulus carbon fibres: Morphological and interfacial characterization

Carbon nanotubes (CNTs) were grown directly on the surface of carbon fibres, using the catalytic chemical vapour deposition. FeCo bimetallic catalysts were deposited on carbon fibres using a simple wet impregnation method. CNTs were synthesized over the prepared catalysts by the catalytic decomposition of acetylene at 750^oC. The uniform CNT formation on the fibre surface was verified using scanning electron microscopy. Raman spectroscopy was employed to evaluate non‐destructively the CNT growth and the CNT quality. Thermo gravimetric analysis and differential thermal analysis were employed as destructive methods to confirm the spectroscopic data. Single CNT‐coated fibre fragmentation tests were performed to examine the interfacial shear strength (ISS) of the modified fibres. Acoustic emission was employed to monitor the fragmentation process in real time. Thus, the coated fibre structural integrity was assessed together with its stress transfer properties. Polarized optical microscopy was employed to cross validate the acoustic emission data. It was found that the ISS of the nanotube‐reinforced interphase was improved without affecting the fibre mechanical properties. Copyright © 2013 John Wiley & Sons, Ltd.     

Oxidative carbonylation of phenol to diphenyl carbonate catalyzed by palladium complexes bridged with N,N‐ligands over functionalized silica

Heterogeneous palladium catalysts anchored on functionalized silica were prepared by sol–gel methods and their catalytic properties for the oxidative carbonylation of phenol to diphenyl carbonate (DPC) were investigated. The catalysts were characterized by means of IR, XPS, EA and BET. The Pd loading in the heterogeneous catalysts and leaching in solution were detected by atomic absorption. The effects of different reaction parameters such as temperature, solvent and inorganic cocatalyst on the yield of DPC and Pd leaching were also studied. It was found that Cu₂O and tetrahydrofuran (THF) were the best partners with these heterogeneous catalysts. In the presence of 3 Å molecular sieves as dehydrating agent, the heterogeneous palladium catalyst prepared from 2‐acylpyridine revealed excellent catalytic performance and stability at 110 °C for 5 h, giving 13.7% yield of DPC based on phenol and 4.0% Pd loss in solution. The heterogeneous catalyst was more active and stable compared with traditional supported Pd? C catalyst under the same reaction conditions. Copyright © 2005 John Wiley & Sons, Ltd.     

Pd/Hβ-zeolite catalysts for catalytic combustion of toluene: Effect of SiO2/Al2O3 ratio

The effect of pure and high silica Hβ zeolites on the catalytic performance of toluene combustion over Pd/H/3 catalyst was evaluated.Pure and high silica β zeolites were prepared by direct synthesis procedures,then 0.1 wt% of palladium was impregnated on different Hβ zeolites via incipient wetness technique using palladium nitrate as the Pd source.The Pd/Hβ catalysts were characterized by XRD,N2 adsorption/desorption,H2O adsorption,NH3-TPD,H2-TPR and XPS techniques.With increasing the SIO2/Al2O3 ratio of β zeolite,the activity of the Pd/Hβ catalysts for toluene combustion increased clearly and the pure silica β zeolite supported Pd catalyst showed the best catalytic activity.The superior catalytic performance of Pd/β catalyst prepared from pure silica β zeolite was attributed to its high hydrophobicity and the preserving ability for PdO active species.     

Novel cyclodextrin‐modified h‐BN@Pd(II) nanomaterial: An efficient and recoverable catalyst for ligand‐free C‐C cross‐coupling reactions in water

An environmentally friendly palladium(II) catalyst supported on cyclodextrin‐modified h‐BN was successfully prepared. The catalyst was characterized by FT‐IR, SEM, TG, XRD and XPS, and the loading level of Pd in h‐BN@β‐CD@Pd(II) was measured to be 0.088 mmol g⁻¹ by ICP. It exhibits excellent catalytic activity for the Suzuki and Heck reactions in water, and can be easily separated and consecutively reused for at least nine times. In addition, a series of pharmacologically interesting products were successfully synthesized using this catalyst to demonstrate its potential applications in pharmaceutical industries. Above all, this work opens up an interesting and attractive avenue for the use of cyclodextrin‐functionalized h‐BN as an efficient support for hydrophilic heterogeneous catalysts.     

Synthesis of palladium colloids within polydimethylsiloxane and their use as catalysts for hydrogenation

The presence of unreacted silanes within cured polydimethylsiloxane (PDMS) leads to the reduction of tetrachloropalladate(II) ions, generating encapsulated palladium colloids. The resulting colloids had varied morphology and were typically less than 80 nm in size. The Pd/PDMS vessels, which contained 0.10±0.01% Pd, were effective catalysts for the hydrogenation of carbon-carbon multiple bonds for at least ten successive runs with no loss of catalytic activity, and the catalyst does not exhibit the same pyrophoric behavior as Pd on carbon after use in hydrogenation reactions. In addition, storage of previously used Pd/PDMS vessels for 6 months in air did not affect the catalytic activity, and the overall morphology of the catalysts after use was the same as those that have not been involved in catalytic reactions.     

Pd-Co/C催化剂上葡萄糖的催化氧化反应

Pd-Co/C催化剂上葡萄糖的催化氧化反应     

Catalytic conversion of cellulose into polyols using carbon-nanotube-supported monometallic Pd and bimetallic Pd–Fe catalysts

A series of carbon nanotube (CNT)-supported monometallic Pd and bimetallic Pd–Fe catalysts were synthesized and employed for catalytic hydrogenolysis of cellulose into polyols, including hexitol, ethylene glycol (EG), 1,2-propanediol (1,2-PG), and glycerol (Gly). The physicochemical properties of the catalysts were characterized by nitrogen physical adsorption measurements, X-ray diffraction analysis, transmission electron microscopy, and X-ray photoelectron spectroscopy. The total yield of hexitol, EG, 1,2-PG, and Gly in hydrolytic hydrogenation of cellulose was 37, 55, and 53% for Pd/CNTs, Pd–Fe/CNTs (Pd:Fe = 1:1), and Pd–Fe/CNTs (Pd:Fe = 1:2), respectively. Addition of Fe to Pd significantly modified the physicochemical properties of the nanoparticles and their catalytic performance, especially regarding hexitol selectivity. The promoting effect of Fe, especially for hexitol selectivity, compared with the monometallic catalyst is due to the fact that incorporation of Fe may stabilize Pd⁰ nanoparticles and lead to downshift of the d-band center of Pd metal nanoparticles by charge transfer from Fe to Pd. Recycling experimental results showed that leaching of Fe resulted in a significant decrease in the hexitol yield obtained using the Pd–Fe/CNTs after the first recycle, further demonstrating that Fe element plays a promoting role for hexitol formation.