Glass transition temperature and thermal decomposition of cellulose powder

Cellulose powder and cellulose pellets obtained by pressing the microcrystalline powder were studied using differential scanning calorimetry (DSC), differential thermal analysis (DTA), and thermal gravimetry (TG). The TG method enabled the assessment of water content in the investigated samples. The glass phase transition in cellulose was studied using the DSC method, both in heating and cooling runs, in a wide temperature range from −100 to 180 °C. It is shown that the DSC cooling runs are more suitable for the glass phase transition visualisation than the heating runs. The discrepancy between glass phase transition temperature T _g found using DSC and predictions by Kaelbe’s approach are observed for “dry” (7 and 5.3% water content) cellulose. This could be explained by strong interactions between cellulose chains appearing when the water concentration decreases. The T _g measurements vs. moisture content may be used for cellulose crystallinity index determination.     

Thermally stimulated current and DSC studies of the broadened glass transition in liquid crystalline polymers

The high sensitivity of the thermally stimulated current, thermal sampling (TS) method is emphasized in a study of the breadth of the glass transition in several liquid-crystalline polymers (LCPs). Differential scanning calorimetry (DSC) was performed on all samples to further quantify the glass transition regions. For “random” copolyester LCPs with widely varying degrees of crystallinity, including highly amorphous samples, very broad glass tran-sition regions were observed. One semicrystalline alternating copolyester and a series of semicrystalline azomethine LCPs were studied as examples of structurally regular polymers. These exhibited relatively sharp glass transitions more comparable to ordinary isotropic amorphous or semicrystalline polymers. The broad glass transitions in the random copolyesters are attributed to structural heterogeneity of the chains. In one example of a moderate-crystallinity random copolyester LCP (Vectra), glass transitions ranging up to ca. 150°C in breadth were determined by the thermal sampling (TS) method and DSC. In other lower crystallinity copolyester LCPs, the main glass transition temperature as determined by DSC was comparable to that determined by TSC although cooperative relaxations of a minor fraction of the overall relaxing species were detected well below the main T_g, by the TS method and not by DSC. Rapid quenches from the isotropic melt to an isotropic glass were possible with one LCP. The anisotropic and isotropic glassy states for this LCP were found to have the same breadth of the glass transition as was determined by the TS method, although TSC and DSC show that T_g is shifted downward by ca. 15°C in the anisotropic glass as compared to the isotropic glass. © 1993 John Wiley & Sons, Inc.     

Thermal behavior of the poly(2-methoxy)-Cyanurate of 1,1′-bis(4-hydroxy phenyl)-Cyclohexane

Thermal behavior of unfractionated poly(2-methoxy)-Cyanurate, PMCBC- film has been reported. The degradation of the polymer involved two steps. The glass transition temperature, T_g, from DSC and DMA studies is ～ 200°C. TMA study shows that the glass-rubber transition region is in the range of 157 to 199°C. The thermal stability of PMCBC has been found to be superior to commercially available polymers.     

The relation between the microphase separation transition and the glass transition in diblock copolymers

The microphase separation transition (MST) has been studied for short chain diblock copolymers poly(styrene-b-isoprene) and poly(styrene-b-mma). A detailed analysis of small-angle x-ray scattering (SAXS) profiles in the homogeneous phase allows determination of the interaction parameter and the spinodal temperature T_s of the MST. T_s for the PS/PI diblocks is found to be lower than the glass transition temperature of their hard blocks. This results in a coupling of the MST and the glass transition. Using both structural (SAXS) and thermal differential scanning calorimetry (DSC) methods it is shown that an endothermal peak found in the DSC diagrams is related to the combined effect of the MST and the glass transition. © 1992 John Wiley & Sons, Inc.     

Thermal properties of poly(lactic acid)/organo-montmorillonite nanocomposites

Poly(lactic acid)/organo-montmorillonite nanocomposites were prepared by melt intercalation technique. Maleic anhydride-grafted ethylene propylene rubber (EPMgMA) was added into the PLA/OMMT in order to improve the compatibility and toughness of the nanocomposites. The samples were prepared by single screw extrusion followed by compression molding. The effect of OMMT and EPMgMA on the thermal properties of PLA was studied. The thermal properties of the PLA/OMMT nanocomposites have been investigated by using differential scanning calorimeter (DSC) and thermo-gravimetry analyzer (TG). The melting temperature (T _m), glass transition temperature (T _g), crystallization temperature (T _c), degree of crystallinity (χ_c), and thermal stability of the PLA/OMMT nanocomposites have been studied. It was found that the thermal properties of PLA were greatly influenced by the addition of OMMT and EPMgMA.     

Thermal Properties of Poly(L-lactide)/Calcium Carbonate Nanocomposites

Summary: Thermal properties of nanocomposites prepared of poly(L-lactide) (PLLA) and CaCO₃ applying differential scanning (DSC) calorimetry and thermogravimetry (TG) were studied. Nanocomposites were prepared by extrusion process at 170 °C. DSC measurements show that CaCO₃ has no influence on glass transition and melting point of PLLA but lowers its cold crystallization temperature. There is no difference in glass transition temperature of PLLA before and after extrusion. High temperature thermal stability of the PLLA in the composites is poorer than neat PLLA. Kinetic parameters also indicate greater reactivity of the system upon CaCO₃ addition.     

The kinetics of phase transitions in vitreous chalcogenide semiconductors As10.2Se89.8 and As9Se90Bi in early stage of physical ageing process

The kinetics of glass transition in selenide glasses As_10.2Se_89.8 and As₉Se₉₀Bi in early stage of physical ageing process has been investigated by parallel differential scanning calorimetry (DSC) and exoelectron emission (EEE). It has been found that the glass transition process occurring in investigated glasses is evidenced by peaks on EEE intensity and DSC curves. Admixture of bismuth causes a distinct lowering of the temperature of glass transitions process both in the surface layer and in the volume. The addition of Bi causes a decrease in the value of the activation energy for glass transition process in both the volume and in the surface layer, thus reducing the thermal stability of investigated glasses. Physical ageing in Se-rich chalcogenide glasses leads to a significant increase of endothermic peak area A, temperature of glass transition T _g and decrease of the activation energy value E. All these effects are strongly dependent on glass composition.     

Glass Stability and Glass Forming Ability of Ge25−xSe75Sbx (x = 12, 15, and 18) Chalcogenide Glasses Using Thermal Parameters

In the present communication glass stability (GS) and glass forming ability (GFA) of Ge_25−xSe₇₅Sb_x (x = 12, 15, and 18) chalcogenide glasses have been calculated in terms of certain thermal parameters, i.e., reduced glass transition temperature (T_rg), Hruby number (H), S-parameter (S), and ΔT. The glassy samples have been prepared by quenching of melt technique. For structure characterization, XRD technique has been used. For thermal analysis Differential Scanning Calorimetery (DSC) has been used. DSC scans have been recorded at different heating rates, i.e., 5, 10, 15, and 20 K min⁻¹. Stability of glassy samples has also been confirmed in terms of activation energy of glass transition calculated by Kissinger relation. All these parameters indicate that GS and GFA both decrease with increase of Sb content in Ge_25−xSe₇₅Sb_x (x = 12, 15, and 18) glassy series.     

Thermal properties and liquid crystallinity of side-chain azobenzene copolymer containing pendant polyhedral oligomeric silsequioxanes

Vinylated polyhedral oligomeric silsesquioxane (POSS-M) was prepared by the reaction of POSS containing amine groups with acrylic acid. Azobenzene liquid crystalline copolymer (LCP-POSS) was then synthesized with 6.0 mol% POSS-M and 94.0 mol% acrylate monomer containing azobenzene liquid crystalline moiety (Azo-M) by free-radical copolymerization. Homopolymer of Azo-M (LCP) was also synthesized under the same conditions. Their thermal properties and liquid crystallinity were characterized by Thermal gravimetric analysis (TG), differential scanning calorimetry (DSC), Wide-angle X-ray diffraction experiments (XRD) and polarized optical micrographs (POM). The results showed that LCP-POSS has higher thermal stability and glass transition temperature than pure LCP due to the incorporation of the rigid cage-like POSS. Especially, LCP-POSS exhibits enantiotropic smectic and nematic liquid crystalline behaviors, its smectic-nematic transition temperature (T _SN) and nematic-isotropic transition temperature (T _NI) are higher than those of pure LCP, which may promote and extend its applications on stimuli-responsive materials and devices.     

Measuring the Glass Transition of Thermosets by Alternating Differential Scanning Calorimetry

The glass transition temperature of thermosets is determined by alternating differential scanning calorimetry (ADSC), which is a temperature modulated DSC technique. The different values of the glass transition obtained from heat flow measurements (total and reversible) and heat capacity (modulus of the complex heat capacity) are analysed and compared with the values obtained by conventional DSC. The effect of the sample mass on the values of T_g, heat capacity and phase angle has been analysed. The effect of the thermal contact between sample and pan has been studied using samples cured directly inside the pan and disc-shaped samples of different thickness. The results obtained for the thermal properties and the phase angle are compared and analysed. The modulus of the complex heat capacity enables the determination of the dynamic glass transition, T_g, which is frequency dependent. The apparent activation energy ofthe relaxation process associated with the glass transition has been evaluated from the dependence of T_g on the period of the modulation.This revised version was published online in November 2005 with corrections to the Cover Date.     

StepScan DSC

StepScan DSC technique was used for the study of the glass transition phenomenon. This method allows relatively good monitoring of reversing and non-reversing processes, and thus is very useful tool for glass transition studies of wide type of glass-forming materials, including inorganic glasses as well as organic polymers. In this work, experience with the StepScan DSC technique is summarized. Some interesting results of its application are presented, such as determination of glass transition temperature independent on thermal history of glass, discovered relationship between the slope of temperature dependence of C _p in T _g, and Angel’s index of fragility and estimation of viscosity glass transition temperature, T _g,η.     

Thermal analysis of protein–metallic ion systems

Advanced thermal analysis methods, such as temperature modulated DSC (differential scanning calorimetry) and quasi-isothermal TMDSC were used to analyze the protein–metallic ion interactions in silk fibroin proteins. The precise heat capacities were measured and theoretically predicted in this study. To remove bound water and simplify the system, a thermal cycling treatment through both standard DSC and TMDSC was used to detect the underlying heat capacity and reveal the phase transitions of the silk–metallic salts system. Results show that K⁺ metallic salts play the role of plasticizer in silk fibroin proteins, which reduces the glass transition (T_g) of the pure silk protein and negatively affects its structural thermal stability. On the other hand, Ca²⁺ metallic salts act as an anti-plasticizer, and increase the glass transition and the thermal stability of the silk protein structure. This indicates that the thermal analysis methods offer a new pathway to study protein–metallic ion systems, yielding very fruitful information for the study of protein structures in the future.     

Thermal properties of microcrystalline cellulose-filled PET–PTT blend polymer composites

Polymer composite materials were prepared from poly(ethylene terephthalate)–poly(trimethylene terephthalate) blends as the matrix and different microcrystalline cellulose (MCC) filler levels (0–40 wt%) using melt compounding followed by compression molding. The composites were analyzed using dynamic mechanical thermal analysis (DMTA), differential scanning calorimetry (DSC) and thermogravimetric analysis (TG). The DSC results indicated that there is no consistent or significant influence of the MCC addition on the glass transition (T _g), melting (T _m), and crystallization temperature of the composites. With increasing MCC content, dynamic mechanical properties improved because of the reinforcing effect of the MCC. The tan δ peak values from the DMTA were not significantly changed as the MCC content increased. TG indicated that the onset temperature of rapid thermal degradation decreased with increasing MCC content. It was also found that the thermal stability of the composites slightly decreased as the MCC content increased.     

Effect of Wood Content on The Thermal Behavior and on The Molecular Dynamics of Wood/Plastic Composites

Summary: In the last decades, the growing environmental awareness has resulted in a renewed interest in the use of natural materials for different applications. In this context, the use of wood in plastic to obtain composites has grown significantly. In the present work, heartwood and sapwood from Angelim Pedra (Hymenolobiun petraeum) were used to prepare PVC/wood composites. To study the composites with different wood types and filler contents the molecular dynamic was investigated through low field NMR by poton spin- lattice relaxation time measurements (T₁H) and the thermal behavior was characterized by means of differential scanning calorimetry (DSC) focusing the glass transition temperature and thermogravimetric analyses (TGA) observing the changes in the thermal stability. It was found that increasing addition of wood flour (sapwood and heartwood) caused a small but progressive improvement of the decomposition temperature of the composites, whereas the glass transition temperature remains practically unchanged. In the molecular dynamic behavior, a gradual decrease in T₁H values was observed with increasing sapwood and heartwood content, indicating that the composites became less rigid. The distribution curves of the domains showed a better interaction and phase dispersion between the composite components with higher filler content.     

Thermoanalytical evaluation of readily available reference polymers

A commercial set of polymers has been characterized by TG-DTA, DSC, TMA, FTIR spectroscopy and X-ray diffraction analysis (XRD). Thermal and mechanical stability, as well as the polymer glass transition temperature,T _g, and melt temperature,T _m, have been documented. There is a good correlation between measuredT _g andT _m values and published data. The degree of polymer crystallinity for polyethylene has been verified by XRD. The credibility and stability of these reference polymers is based on a comparison of their thermal properties, over a wide range of temperatures from two versions of a reference set, published in 1979 (A) and 1994 (B). The thermal properties and crystallinity of these polymers have stood the test of time and are reliable, readily available and consistent.     

Effect of antimony on glass transition and thermal stability of Se<Subscript>78−x</Subscript>Te<Subscript>18</Subscript>Sn<Subscript>2</Subscript>Sb<Subscript>x</Subscript> (<Emphasis Type="Italic">x</Emphasis> = 0, 2, 4 and 6 at.%) multicomponent glassy alloys

Multicomponent glassy alloys Se_78?xTe₁₈Sn₂Sb_x (x?=?0, 2, 4 and 6) have been synthesized using melt quench technique. The prepared samples have been characterized by X-ray diffraction technique and differential scanning calorimetry (DSC). Glass transition kinetics of Se_78?xTe₁₈Sn₂Sb_x (x?=?0, 2, 4 and 6 at.%) glassy alloys has been examined using DSC. DSC runs have been recorded at different heating rates (5, 10, 15 and 20 K min^?1) for each sample under investigation. Heating rate dependence of glass transition temperature (T_g) has been studied using Lasocka empirical relation. The activation energy of glass transition has been evaluated using Kissinger and Moynihan’s relation. The effect of antimony concentration on glass transition temperature and activation energy has been investigated in the prepared samples. Glass-forming ability and thermal stability of Se_78?xTe₁₈Sn₂Sb_x (x?=?0, 2, 4 and 6) glassy alloys have been monitored through the evaluation of thermal stability using Dietzal relation, Hurby parameter, and Saad and Poulin parameter. The above-mentioned parameters are found to be compositionally dependent, which indicates that among the studied glass samples the stability is maximum for Sb at 2% content.     

Thermal Methods Applied to the Glass Transition of Mixed Network AlPO4–BPO4–SiO2 Glasses

Glass transition effect of mixed network AlPO₄–BPO₄–SiO₂ glasses was studied. DTA/DSC and TMA measurements has been applied in the research. It has been found that glass transition effect has structurally sensitive properties. Glass transition temperature T _g, changes of specific heat (Δc _p)and thermal expansion coefficient (α) accompanying the process depend on the nature and the number of components forming the glassy framework. Character of chemical bonds combining them into the glass structure has an influence on the glass transition effect. Its course is dependent on the flexibility of the structure of glasses. This revised version was published online in July 2006 with corrections to the Cover Date.     

Glass transition, fragility, and structural features of amorphous nickel–tellurate–vanadate samples

The experimental FTIR spectra and DSC curves of the ternary 40TeO₂–(60?x)V₂O₅–xNiO glasses with 0 ≤ x ≤ 30 (in mol%) have been investigated. The glass transition properties that have been measured and reported in this paper, include the glass transition temperature (T _g), glass transition width (ΔT _g), heat capacity change at glass transition (ΔC _P) and Fragility (F). Thermal stability, fragility, and glass-forming tendency of these glasses have been estimated. Also, Poisson’s ratio (μ) and IR spectra of the presented systems have been investigated, to determine relationship between chemical composition and the thermal stability or to interpret the structure of glass. In addition, Makishima and Makenzie’s theory was applied for determination of Young’s modulus, bulk modulus, and shear modulus, indicating a strong relation between elastic properties and structure of glass. In general, results of this work show that glasses with x = 0 and 30 have the highest shear and young’s modulus which make them as suitable candidate for the manufacture of strong glass fibers in technological applications; but it should be mentioned that glass with x = 30 has higher handling temperature and super resistance against thermal shock.     

Derivation of the Kissinger equation for non-isothermal glass transition peaks

A brief derivation of the Kissinger’s equation for analysis of experimental data of non-isothermal glass transition peaks based on the free volume model is given. This equation was applied successfully to Cu_0.3(SSe₂₀)_0.7 chalcogenide glass for different heating rates. For granted this model, the obtained glass transition activation energy, E _g must be constant throughout the whole glass transition temperature range. This required that T _g to be determined for three characteristic temperature points for each DSC curve.     

Morphology and thermal properties of polyhedral oligomeric silsesquioxane/polybutadiene nanocomposites prepared by anionic polymerization

The morphology and thermal properties of Allylisobutyl Polyhedral Oligomeric Silsesquioxane (POSS)/Polybutadiene (PB) nanocomposites prepared through anionic polymerization technique were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). The results of XRD, SEM and TEM showed that the aggregation of POSS in PB matrix occurred obviously, forming crystalline domains and the size of POSS particles increased with increasing POSS content. The DSC and TGA results indicated that the glass transition temperature (T _g) of the nanocomposites was significantly increased and the maximum degradation temperature (T _dmax) of nanocomposites was slightly increased compared with pure PB, implying an increase in thermal stability.