Synthesis and characterization of bisulfonated poly(vinyl alcohol)/graphene oxide composite membranes with improved proton exchange capabilities

Composite membranes based on poly(vinyl alcohol) (PVA) and graphene oxide (GO) were prepared by solution-casting method to be used as proton exchange membranes (PEMs) in fuel cell (FC) applications. Bisulfonation was employed as a strategy to enhance the proton conductivity of these membranes. First, a direct sulfonation of the polymer matrix was accomplished by intra-sulfonation of the polymer matrix with propane sultone, followed by the inter-sulfonation of the polymer chains using sulfosuccinic acid (SSA) as a crosslinking agent. Furthermore, the addition of graphene oxide (GO) as inorganic filler was also evaluated to enhance the proton-conducting of the composite membranes. These membranes were fully characterized by scanning electron microscopy (SEM), Fourier transformed infrared spectroscopy (FTIR), thermogravimetric analysis (TGA) and tensile tests. Besides, the proton conductivity of these membranes in a fully hydrated state was also analyzed by electrochemical impedance spectroscopy (EIS). The effect of the intra- and inter-sulfonation of the polymer matrix on the structural, morphological, thermal and mechanical properties of the membranes were determined. Increasing the density of sulfonic acid groups in the membranes resulted in a trade-off between a better proton conductivity (improving from 0.26 to 1.00 mS/cm) and a decreased thermal and mechanical stability. In contrast, the incorporation of GO nanoparticles into the polymer matrix improved the thermal and mechanical stability of both bisulfonated composite membranes. The proton conductivity appreciably increased by the combination of bisulfonation and introduction of GO nanoparticles into the polymer matrix. The sPVA/30SSA/GO composite membrane exhibited a proton conductivity of 1.95 mS/cm at 25 °C. The combination of the GO nanoparticles with the chemical bisulfonation approach of PVA allows thus assembling promising proton exchange membrane candidates for fuel cell applications.     

Preparation and characterization of crosslinked PVA/SiO2 hybrid membranes containing sulfonic acid groups for direct methanol fuel cell applications

Organic–inorganic hybrids based on poly(vinyl alcohol) (PVA)/SiO₂ hybrid membranes containing sulfonic acid groups were prepared using the sol–gel process under acidic conditions. The PVA/sulfosuccinic acid (SSA)/silica hybrid membranes were fabricated from different SSA contents. The proton conductivity and methanol permeability of the hybrid membranes were studied with changing SSA content from 5 to 25 wt.%. It was found that the proton conductivity and the methanol permeability were dependent on the SSA content both as a crosslinking agent, and as a donor of the hydrophilic SO₃H group. Up to an SSA content of about 20 wt.%, both of these properties decrease, and above this SSA content, they begin to increase with increasing SSA content. The proton conductivities of the PVA/SSA/silica membranes were in the range of 10⁻³ to 10⁻² S/cm, and the methanol permeabilities ranged between 10⁻⁸ and 10⁻⁷ cm²/s. The presence of silica particles in the organic polymer matrix, which reduce the free water ratio of the membranes, results in hybrids with markedly reduced methanol permeabilities. These characteristics of the PVA/SSA/silica hybrid membranes are desirable for future applications related to direct methanol fuel cells.     

Properties of Poly(Vinyl Alcohol)‐Based Composite Membranes for Direct Methanol Fuel Cell Applications

The feasibility of poly(vinyl alcohol)(PVA)/sulfosuccinic acid(SSA)/heteropolyacid (HPA) composite membranes was investigated to apply for direct methanol fuel cells (DMFC). The composite membranes were prepared by the solution casting method and their properties were examined. The FTIR spectra showed that the Keggin unit of HPA was preserved in the composite membranes and that specific interactions were involved between PVA and HPA. The composite membranes showed uniform distribution of PWA particles in the PVA/SSA/PWA composite membranes by FE‐SEM. The HPA bleeding out was observed to decrease with increasing HPA concentration. The proton conductivity of PVA/SSA/HPA composite membranes improved at low HPA concentration (5‐10 wt.%), while those properties decreased as HPA concentration increased over 10 wt.%.     

Preparation and characterization of PVDF‐based blend membranes as polymer electrolyte membranes in fuel cells: Study of factor affecting the proton conductivity behavior

There is a huge demand especially for polyvinylidene fluoride (PVDF) and its copolymers to provide high performance solid polymer electrolytes for use as an electrolyte in energy supply systems. In this regard, the blending approach was used to prepare PVDF‐based proton exchange membranes and focused on the study of factor affecting the ir proton conductivity behavior. Thus, a series of copolymers consisting of poly (methyl methacrylate) (PMMA), polyacrylonitrile (PAN), and poly(2‐acrylamido‐2‐methyl‐l‐propanesulfonic acid) (PAMPS) as sulfonated segments were synthesized and blended with PVDF matrix in order to create proton transport sites in PVDF matrix. It was found that addition of PMMA‐co‐PAMPS and PAN‐co‐PAMPS copolymers resulted in a significant increase in porosity, which favored the water uptake and proton transport at ambient temperature. Furthermore, crystallinity degree of the PVDF‐based blend membranes was increased by addition of the related copolymers, which is mainly attributed to formation of hydrogen bonding interaction between PVDF matrix and the synthesized copolymers, and led to a slight decrease in proton conductivity behavior of blend membranes. From impedance data, the proton conductivity of the PVDF/PMMA‐co‐PAMPS and PVDF/PAN‐co‐PAMPS blend membranes increases to 10 and 8.4 mS cm⁻¹ by adding only 50% of the related copolymer (at 25°C), respectively. Also, the blend membranes containing 30% sulfonated copolymers showed a power density as high as 34.30 and 30.10 mW cm⁻² at peak current density of 140 and 79.45 mA cm⁻² for the PVDF/PMMA‐co‐PAMPS and PVDF/PAN‐co‐PAMPS blend membranes, respectively. A reduction in the tensile strength was observed by the addition of amphiphilic copolymer, whereas the elongation at break of all blend membranes was raised.     

Morphology and crystallization behavior of poly(vinylidene fluoride)/poly(methyl methacrylate)/methyl salicylate,and benzophenone systems via thermally induced phase separation

Poly(vinylidene fluoride) (PVDF) blend microporous membranes were prepared by PVDF/poly(methyl methacrylate) blend (with mass ratio = 70/30) via thermally induced phase separation. Benzophenone (BP) and methyl salicylate (MS) were used as diluents. The phase diagram calculations were carried out in terms of a pseudobinary system, considering the PVDF blend to be one component. The crytallization behaviors of PVDF in the dilutions were detected by differential scanning calorimetry measurement. In these two systems, the melting and crystallization temperatures leveled off in the low polymer concentration (<40 wt %), but shifted to a higher temperature when the polymer concentration >40 wt %. The calculated crystallinity of PVDF for samples with low polymer concentrations was greater than those with high polymer concentrations, because of the limited mobility of polymer chains at a high polymer concentration. The membrane structure as determined by scanning electron microscopy depended on the phase separation mechanism. The quenched samples mainly illustrated the occurrence of crystallization on the same time scale as the liquid–liquid phase separated, resulting in the obvious spherulitic structure with small pores in the spherulites. As the polymer concentration increased, the size of the spherulites and pores within the spherulite was decreased. The evaluated porosity for BP diluted system was higher than that for MS diluted system, and decreased with the increased polymer concentration. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 248–260, 2009     

DMFC用PES/SPEEK共混阻醇质子交换膜

将磺化聚醚醚酮(SPEEK, 磺化度DS为68.3%)和聚醚砜(PES)两种聚合物共混制得PES/SPEEK共混膜. DSC研究表明两种聚合物之间具有较好的相容性, 因而共混膜均匀致密, 未发生大尺度相分离. PES的混入能有效降低膜的溶胀度及甲醇透过系数. 纯SPEEK 膜40 ℃时在1 mol•L−1甲醇水溶液中溶胀度达到160%, 45 ℃时就完全溶解, 而含30%(w)PES的共混膜在80 ℃时的溶胀度仅有15%. 室温下含20%−30%(w)PES的共混膜的甲醇透过系数为1×10−7 cm2•s−1左右, 比Nafion 115膜的透过系数小一个数量级. 尽管80 ℃下30%(w)PES/SPEEK共混膜的电导率与Nafion 115膜相当, 但由于共混膜的厚度比Nafion 115膜小1/3左右, 膜电阻较小, 因而其电池性能比Nafion 115膜的好.     

Fabrication and optimization of proton conductive polybenzimidazole electrospun nanofiber membranes

Phosphoric acid (PA)–doped polybenzimidazole (PBI) proton exchange membranes have received attention because of their good mechanical properties, moderate gas permeability, and superior proton conductivity under high temperature operation. Among PBI‐based film membranes, nanofibrous membranes withstand to higher strain because of strongly oriented polymer chains while exhibiting higher specific surface area with increased number of proton‐conducting sites. In this study, PBI electrospun nanofibers were produced and doped with PA to operate as high temperature proton exchange membrane, while changes in proton conductivity and morphologies were monitored. Proton conductive PBI nanofiber membranes by using the process parameters of 15 kV and 100 μL/h at 15 wt% PBI/dimethylacetamide polymer concentration were prepared by varying PA doping time as 24, 48, 72, and 96 hours. The morphological changes associated with PA doping addressed that acid doping significantly caused swelling and 2‐fold increase in mean fiber diameter. Tensile strength of the membranes is found to be increased by doping level, whereas the strain at break (15%) decreased because of the brittle nature of H‐bond network. 72 hour doped PBI membranes demonstrated highest proton conductivity whereas the decrease on conductivity for 96‐hour doped PBI membranes, which could be attributed to the morphological changes due to H‐bond network and acid leaking, was noted. Overall, the results suggested that of 72‐hour doped PBI membranes with proton conductivity of 123 mS/cm could be a potential candidate for proton exchange membrane fuel cell.     

Proton‐conductive membranes based on blends of polyimides

We prepared novel proton‐conductivity membranes based on blends of sulfonated polyimides. The blend membranes were prepared from a sulfonated homopolyimide and a sulfonated copolyimide with a solvent‐casting method. The proton conductivities of the blend membranes were measured as functions of the temperature with four‐point‐probe electrochemical impedance spectroscopy. The conductivity of the membranes strongly depended on the sulfonated homopolyimide content and increased with an increase in the content. The proton conductivity of all the blended membranes indicated a higher value than that determined in Nafion at 80 °C, and this may mean that the proton transfer in the blend membranes is responsible for the ionic channels induced by the hydrophobic and hydrophilic domains. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1325–1332, 2007     

Sulfonated polybenzimidazoles: Proton conduction and acid–base crosslinking

A series of soluble, benzimidazole‐based polymers containing sulfonic acid groups (SuPBI) has been synthesized. SuPBI membranes resist extensive swelling in water but are poor proton conductors. When blended with high ion exchange capacity (IEC) sulfonated poly(ether ether ketone) (SPEEK), a polymer that has high proton conductivity but poor mechanical integrity, ionic crosslinks form reducing the extent of swelling. The effect of sulfonation of PBI on crosslinking in these blends was gauged through comparison with nonsulfonated analogs. Sulfonic acid groups present in SuPBI compensate for acid groups involved in crosslinking, thereby increasing IEC and proton conductivity of the membrane. When water uptake and proton conductivity were compared to the IEC of blends containing either sulfonated or nonsulfonated PBI, no noticeable distinction between PBI types could be made. Comparisons were also made between these blends and pure SPEEK membranes of similar IEC. Blend membranes exhibit slightly lower maximum proton conductivity than pure SPEEK membranes (60 vs. 75 mS cm^?1) but had significantly enhanced dimensional stability upon immersion in water, especially at elevated temperature (80 °C). Elevated temperature measurements in humid environments show increased proton conductivity of the SuPBI membranes when compared with SPEEK‐only membranes of similar IEC (c.f. 55 for the blend vs. 42 mS cm^?1 for SPEEK at 80 °C, 90% relative humidity). © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3640–3650, 2010     

SPEEK/PES-C、SPEEK/SPES-C共混质子交换膜研究

通过在磺化聚醚醚酮(SPEEK,DS=61.68%)中分别混入酚酞型聚醚砜(PES-C)、磺化酚酞型聚醚砜(SPES-C,DS=53.7%)制备出SPEEK/PES-C、SPEEK/SPES-C共混质子交换膜.结果表明,共混的两种聚合物之间均具有较好的相容性.PES-C、SPES-C的混入能有效降低膜的溶胀及甲醇透过,且随着共混量的增加,这种作用越趋明显.纯SPEEK膜在75℃左右溶解,而SPEEK/PES-C(30wt%)、SPEEK/SPES-C(30wt%)共混膜在80℃时溶胀度仅为22.5%、26.32%.在室温至80℃范围内,纯SPEEK及共混膜的甲醇透过系数都在10-7cm2.s-1数量级上,远小于Nafion115膜.在饱和湿度下,温度大于90℃时,SPEEK/PES-C(20wt%)共混膜电导率超过Nafion115膜;温度大于110℃时,SPEEK/SPES-C(30wt%)共混膜电导率与Nafion115膜相当,达到0.11S.cm-1.高电导率,低透醇系数以及明显提高了的可使用温度表明该类共混膜有望在DMFC中使用.     

Pervaporation of alcohol-toluene mixtures through polymer blend membranes of poly(acrylic acid) and poly(vinyl alcohol)

Homogeneous membranes were prepared by blending poly(acrylic acid) with poly(vinyl alcohol). These blend membranes were evaluated for the selective separation of alcohols from toluene by pervaporation. The flux and selectivity of the membranes were determined both as a function of the blend composition and of the feed mixture composition. The results showed that a polymer blending method could be very useful to develop new membranes with improved permselectivity. The pervaporation properties could be optimized by adjusting the blend composition. All the blend membranes tested showed a decrease in flux with increasing poly(vinyl alcohol) content for both methanol—toluene and ethanol—toluene liquid mixtures. The alcohols permeated preferentially through all tested blend membranes, and the selectivity values increased with increasing poly(vinyl alcohol) content. The pervaporation characteristics of the blend membranes were also strongly influenced by the feed mixture composition. The fluxes increased exponentially with increasing alcohol concentration in the feed mixtures, whereas the selectivities decreased for both liquid mixtures.     

含羧基交联型质子交换膜的制备及其性能

合成了一种含酯基的磺化聚合物,利用后水解的方法得到了含有羧基侧基的聚合物;将磺化聚合物与聚乙烯醇通过溶液共混,热处理后得到交联型的共混膜材料。 研究结果表明,膜材料的玻璃化转变温度(Tg)有明显的上升,证明了交联反应的发生;同时,膜的吸水率和溶胀率有一定的下降,力学性能和热稳定性也有一定的提升。 通过共价交联的方法,制备了综合性能优异的磺化聚芳醚质子交换膜材料。 在100 ℃,交联膜的质子传导率为0.072~0.065 S/cm,吸水率为51%~89%,溶胀率为19%~30%。     

Blend membranes of Nafion/sulfonated poly(aryl ether ketone) for direct methanol fuel cell

Sulfonated poly(aryl ether ketone) (sPAEK) synthesized by LG Chem. was confirmed by FT-IR. To estimate the thermal stability, glass transition temperature and decomposition temperature were investigated. They showed that sPAEK had good thermal properties. The proton conductivity, methanol permeability and water uptake of sPAEK were also measured. Nafion/sulfonated poly(aryl ether ketone) composite membranes were prepared by blending two materials. The blend ratios of sPAEK and Nafion were 2:1, 3:1, 5:1, and 7:1. The blend membranes showed phase separated morphology since they became immiscible during the solvent evaporation process. Due to the differences in specific gravity and solvent concentration profile during the solvent evaporation process, the upper region had lower Nafion volume fraction with smaller domains and the lower region had higher Nafion volume fraction with larger domains. Mechanical properties such as the stress at break, yield stress, Young's modulus, and elongation at break were measured. The sPAEK had better mechanical properties than Nafion. The mechanical properties increased with increasing sPAEK content. Proton conductivity and methanol permeability of the blend membranes were lower than those of Nafion. Both decreased with decreasing Nafion content. Since the methanol permeability of sPAEK was lower than that of Nafion, sPAEK acted as the methanol barrier. Water uptake of sPAEK was higher than that of Nafion.     

PPO-based acid–base polymer blend membranes for direct methanol fuel cells

New acid–base polymer blend membranes for direct methanol fuel cells (DMFC) have been designed using a very accessible commercial polymer, poly(2,6-dimethyl-1,4-phenylene oxide) (PPO). The preparation begins with the sulfonation and bromination of PPO to sulfonated PPO (SPPO) and bromomethylated PPO (BrPPO), respectively. Blend membranes are formed by mixing n-propylamine(PrNH₂)-neutralized SPPO and PrNH₂-aminated BrPPO solutions in N-methyl-2-pyrrolidone (NMP), and casting the mixed solution on glass petri dishes followed by acidification with aqueous hydrochloric acid. The compatibility between the acid and base components of the blend is assured by using acidic and basic polymers deriving from the same parent polymer (PPO). Ionic crosslinking is established between the sulfonic groups of SPPO and the amine groups of aminated BrPPO. The ionic crosslinking strengthens the membrane dimensional stability by reducing water uptake and membrane swelling up to temperatures as high as 80 °C. The membranes fabricated as such display good resistance to methanol crossover amidst some, but acceptable loss of proton conductivity. The characteristic factor (i.e. the ratio of proton conductivity to methanol permeability) increases noticeably with the BrPPO content, with the sample containing 30 wt.% BrPPO showing a 16-fold improvement over Nafion 117. The mechanical properties and oxidative stability of the blend membranes also satisfy the requirements for fuel cell assembly and operation.     

Synthesis and properties of new fluorinated polymers bearing pendant imidazole groups for fuel cell membranes operating over a broad relative humidity range

New alternating copolymers comprising a chlorotrifluorinated backbone and imidazole‐terminated pendant ethylene oxide groups have been prepared with a view to their use as a component of proton‐conducting membranes in polymer electrolyte fuel cells. A vinyl ether containing an imidazole (Imi) function protected by a benzyl group (BVI) was first synthesized in a three‐step reaction. It was then copolymerized in solution with chlorotrifluoroethylene (CTFE) by conventional radical copolymerization leading to alternating poly(BVI‐alt‐CTFE) copolymers in good yields. Deprotection of the benzyl group under hydrogen produced a chlorotrifluorinated poly(Imi‐alt‐CTFE) copolymer. The polymer was subsequently used to form blend membranes with sulfonated poly(ether ether ketone) (sPEEK). The conductivity of blend membranes of poly (Imi‐alt‐CTFE) with sPEEK lies in the range of 4–10 mS cm^?1 at 40–70 °C and, for blend membranes rich in poly(Imi‐alt‐CTFE), is little dependent on relative humidity between 30 and 100%. It is surmised that the polymer and membrane composition favor microstructural phase separation into chlorotrifluorinated polymer backbone domains and regions in which imidazole groups are clustered. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 223–231, 2010     

Synthesis and properties of a new fluorine‐containing polybenzimidazole for high‐temperature fuel‐cell applications

An amorphous, organosoluble, fluorine‐containing polybenzimidazole (PBI) was synthesized from 3,3′‐diaminobenzidine and 2,2‐bis(4‐carboxyphenyl)hexafluoropropane. The polymer was soluble in N‐methylpyrrolidinone and dimethylacetamide and had an inherent viscosity of 2.5 dL/g measured in dimethylacetamide at a concentration of 0.5 g/dL. The 5% weight loss temperature of the polymer was 520 °C. Proton‐conducting PBI membranes were prepared via solution casting and doped with different amounts of phosphoric acid. In the methanol permeability measurement, the PBI membranes showed much better methanol barrier ability than a Nafion membrane. The proton conductivity of the acid‐doped PBI membranes increased with increasing temperatures and concentrations of phosphoric acid in the polymer. The PBI membranes showed higher proton conductivity than a Nafion 117 membrane at high temperatures. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4508–4513, 2006     

Effect of selective swelling on protons and methanol transport properties through partially sulfonated block copolymer membranes

The partially sulfonated polystyrene-b-poly(ethylene-ran-butylene)-b-polystyrene (SSEBS) and its membranes blended with a low molecular weight of hydrogenated dicyclopentadine (DCPD) as a selective swelling agent to the middle block were prepared for a possible application to DMFC. The characteristic properties such as proton conductivity and methanol permeability were compared with SSEBS and the blend membranes when they have the same ion exchange capacity (IEC). Using small-angle X-ray scattering (SAXS), morphological transition by the selective swelling were observed as water and methanol are absorbed. It was found that the addition of DCPD prohibits the morphology transition and reduces the methanol crossover. By means of selective blending with methanol-hating materials, it was shown that satisfactory membranes being with methanol tolerance for DMFC can be fabricated by controlling the nano-scaled morphology of proton conducting block copolymer membranes.     

Sulfonated poly(fluorenyl ether) membranes containing perfluorocyclobutane groups for fuel cell applications

This paper describes the preparation and electrochemical properties of new proton conducting polymer membranes, sulfonated poly(fluorenyl ether) membrane-containing perfluorocyclobutane (PFCB) moieties for fuel cell applications. The sulfonated polymers were prepared via thermal cyclodimerization of 9,9-bis(4-trifluorovinyloxyphenyl)fluorene and subsequent post-sulfonation using chlorosulfonic acid (CSA) as a sulfonating agent. The post-sulfonation reaction was carried out by changing the molar ratio of CSA/repeating unit of the polymer at room temperature for 5 h and the resulting sulfonated polymers showed different degrees of sulfonation (DS) and ion exchange capacities (IEC). With the increment of CSA content, the DS, IEC and water uptake of the sulfonated polymer membranes increased. Their proton conductivity was investigated as a function of temperature. The polymer membrane with an IEC value of 1.86 mmol/g showed a water content of 25% similar to Nafion-115's but showed higher proton conductivity than Nafion-115 over the temperature 25–80 °C. The polymer membrane with lower water uptake and higher IEC showed similar proton conductivity and methanol permeability to Nafion-115. These results confirmed that the sulfonated poly(fluorenyl ether)-containing PFCB groups could be a promising material for fuel cell membranes.     

Preparation and characterization of composite membranes with Brønsted acidic ionic liquid

Poly-(vinyl alcohol) (PVA) proton-conducting composite membranes were prepared using succinic acid (SA) as a cross-linking agent and Brønsted acidic ionic liquid (BAIL) as a proton source. The incorporated BAILs resulted in a relatively high proton conductivity compared with PVA/SA membrane without BAILs. The proton conductivities of PVA/SA/BAIL composite membranes increased versus the BAIL content. In addition, the optimal resultant proton conductivity of PVA/SA/BAIL composite membrane under dry condition could reach 0.4 mS/cm at 140 °C, which was higher than that of PVA/sulfosuccinic acid (SSA) composite membrane (0.032 mS/cm), PVA/SSA/5-aminotetrazole membrane (0.022 mS/cm at 130 °C), and PVA/chlorosulfonic acid/glutaraldehyde membrane (0.0585 mS/cm at 90 °C) measured at the same condition. It was notable that the PVA/SA/BAIL composite membranes could reach high thermal stability up to 150 °C, which was higher than that of traditional PVA membranes (below 80 °C).     

磷酸掺杂聚乙烯醇质子交换膜的甲醇渗透及其质子导电性能的研究

系统研究了甲醇溶液浓度、磷酸含量以及温度对聚乙烯醇 -磷酸 (PVA- x H3 PO4) (0 相似文献