LaNi1 − x Cu x O3 (x = 0.05, 0.10, 0.30) coated electrodes for oxygen evolution in alkaline medium

LaNi_1???x Cu _x O₃ (x?=?0.05, 0.10, 0.30) coated electrodes were prepared by brush painting using Ni foam substrates in order to increase its active surface area. For comparison, coatings with x?=?0.05 were also prepared using vitreous carbon substrates. Cyclic voltammetry was used to evaluate the coating roughness (R _f). Values between 5,145?±?148 and 6,334?±?277 were obtained, depending on the x value, for the coatings on Ni foam. These results show that the electrodes prepared with LaNi_1???x Cu _x O₃ powder, obtained at 600 °C, lead to a big increase on the oxide electrode roughness when compared with LaNiO₃ electrodes prepared by a similar method. Much lower values were obtained for the coatings on vitreous carbon indicating that the substrate nature is also a key factor for the preparation of high surface area electrodes. The calculated kinetic parameters for the oxygen evolution reaction (OER) show that the partial replacement of Ni by Cu has no beneficial effect on the intrinsic catalytic activity of the coatings. On the other hand, a big increase on the active area is observed even for small amounts of Cu (x?=?0.05), leading to a better overall OER performance for the LaNi_0.95Cu_0.05O₃ coating on Ni foam. For this composition, the activity is dominated by geometric effects.     

Nonstoichiometry and structural intergrowth in the CaFexMn1−xO3−y (0 ≤ x ≤ 1) system

An electron diffraction and microscopy study of the CaFe_xMn_1−xO_3−y system treated at 1100°C in air has been performed. An increase of y is accompanied by an increase of the cubic perovskite substructure parameter, the nonstoichiometry being accommodated in several ways. The system contains two solid solutions of the perovskite-type (P) and of the brownmillerite-type (B) and also an intermediate phase (x = 0.6) which makes disordered intergrowth with the B-type solid solution. These results are discussed in terms of multitwinning, randomly dispersed oxygen deficiency, and ordered and disordered intergrowth formation.     

High-temperature transport and stability of SrFe1−xNbxO3 − δ

The conductivity is measured in the series of solid solutions SrFe_1 ? xNb_xO_3 ? δ, where x = 0.05, 0.1, 0.2, 0.3, 0.4, within the oxygen partial pressure limits 10^?18–0.5 atm and temperature range 650–950 °C. The contributions to the total conductivity from oxygen ions, electrons and electron holes are obtained based on their different pressure dependences. The doped derivative with x = 0.1 is found to be a singular composition where ion conductivity attains a maximal value while activation energy for ion transport is minimal. This peculiar behavior is attributed to formation of favorable microstructure in the oxide. The deeper doping results in deterioration of ion transport, which is explained by oxygen vacancy filling. It is shown that replacement of iron for niobium favors enhanced thermodynamic stability towards reduction. The oxygen permeability is evaluated from the conductivity data, and it achieves rather high values in the doped derivatives. These oxides can, therefore, be recommended for further evaluation as oxygen separating membrane materials for partial oxidation of natural gas.     

Novel hollow microspheres MnxCo3−xO4 (x = 1, 2) with remarkable performance for low-temperature selective catalytic reduction of NO with NH3

Journal of Sol-Gel Science and Technology - Hollow microspheres MnCo2O4 and CoMn2O4 have been synthesized by a facile solvothermal route followed by pyrolysis of the carbonate counterparts and...     

Microdomains in the CaFexMn1−xO3−y ferrites: II. Oxidation and reduction of the x = 0.4 composition

It is shown that in the processes of oxidation, reduction, and annealing of samples of the title, three-dimensional microdomains (3D-μD) play a predominant role. These microdomains are intergrown in the three dimensions and allow compositional variations in a very subtile manner. The existence of microdomains seems to be associated with the presence of tetravalent cations and with the fact that all the structures observed are superstructures of the perovskite cell.     

Behavior of Mn3+ ions in four-layered hexagonal (Sr1−x−yLaxBay)MnO3

Stoichiometric four-layered hexagonal (4H) (Sr_1?x?yBa_xLa_y)MnO₃ was synthesized using a standard ceramic technique. Rietveld analysis at room temperature indicated that the Mn–O(1) distance increased and the Mn–O(2) distance decreased with the increase in x. The samples were n-type semiconductors and exhibited hopping conductivity in a small-polaron model below 533 K. The Mn³⁺ ion acted as a donor and the electron transfer became active through the Mn³⁺–O–Mn⁴⁺ path. The samples were antiferromagnetic and the Néel temperature (T_N) was constant regardless of y when x was fixed to 0.3, whereas T_N shifted to a high temperature when y was fixed to 0.02. The face-sharing Mn³⁺–O(2)–Mn⁴⁺ interaction strengthened as the Mn–O(2) distance decreased, and T_N shifted to a high temperature as a result.     

Synthesis, characterization and ion transport properties of hot-pressed solid polymer electrolytes (1−x) PEO:x KI

Synthesis and ion transport properties of hot-pressed solid polymer electrolytes (SPEs), (1-x) PEO: x KI, where x is the content of KI in wt%, are reported. A hot-press technique has been used for the formation of the polymeric membranes in place of the usual solution cast method. The composition (80PEO:20KI) was identified as the highest conducting polymer electrolyte on the basis of compositional dependent conductivity studies of PEO:KI films. A conductivity enhancement of more than two orders of magnitude from that of the pure PEO was achieved. Materials characterization and ion transport mechanism were explained by using various experimental techniques.     

Structural and electrical properties of sol–gel grown (1 − x) (ZnO) + (x) (SnO2) (x = 0, 0.25, 0.5) nanocomposites

Journal of Sol-Gel Science and Technology - Semiconducting oxide nanocomposites of ZnO/SnO2 with different weight ratio, i.e. (i) ZnO:SnO2?=?100:0 (ZnO0), (ii)...     

New Ion Conductor of (Ba1−xLax)2In2O5+x

The structural characterization, thermogravimetric analysis and electrical properties for solid solution system, (Ba_1–xLa_x)₂In₂O_5+x with perovskite-type structure were investigated. X-ray diffraction showed that the orthorhombic phase was in the range of 0.0<x0.3, the tetragonal phase 0.3<x0.5, and the cubic phase 0.5<x. The sharp transition of electrical conductivity shifted to a lower temperature with increasing x and disappeared at the phase boundary between the orthorhombic and tetragonal phases. This perovskite-related oxide exhibited a pure oxide-ion conduction over the oxygen partial pressure range of 1 atm to 10^–3.5 atm, and the electrical conductivity reached the value of 1.610^–1 (S cm^–1) at 1073 K, which was nearly equal to that of the yttria stabilized zirconia. These properties were successfully explained in terms of disordered oxygen ions.This revised version was published online in November 2005 with corrections to the Cover Date.     

Oxygen transport and thermomechanical properties of SrFe(Al)O3-δ –SrAl2O4 composites: microstructural effects

Measurements of oxygen permeation through dense composite membranes showed a considerable influence of processing conditions on the surface exchange kinetics, while the bulk ambipolar conductivity is almost unaffected by microstructural factors. Compared to the materials prepared via the glycine–nitrate process (GNP), the surface limitations to oxygen transport are significantly higher for dual-phase made of a commercial powder synthesized by spray pyrolysis. This difference in behavior may be related to compositional inhomogeneities in the grains of A-site deficient perovskite phase and an enhanced surface concentration of grain boundaries in the case of GNP-synthesized composite, which has also smaller grain size, slightly higher thermal expansion and lower total conductivity. No essential effects on Vickers hardness, varying in the range 6.3–6.5 GPa, were found. The deposition of porous catalyst layers onto the composite surface exposed to reducing environment leads to membrane decomposition. For the fabrication of tubular membranes, the cold isostatic pressing technique was, hence, combined with mechanical treatment to increase the specific surface area without incorporation of catalytically active components.     

Synthesis and characterization of a NASICON phase of variable composition Na1 − x Ni1 − x Sc1 + x (MoO4)3 (0 ≤ x ≤ 0.5)

Subsolidus phase ratios in the Na₂MoO₄-NiMoO₄-Sc₂(MoO₄)₃ system have been studied using X-ray diffraction, differential thermal analysis, and vibrational spectroscopy. A phase of variable composition Na_{1 ? x} Ni_{1 ? x} Sc_{1 + x} (MoO₄)₃ (0 ≤ x ≤ 0.5) having NASICON structure (space group \(R\bar 3c\) ) and a triple molybdate crystallizing in triclinic system (space group \(P\bar 1\) ) have been obtained. The high conductivity of Na_{1 ? x} Ni_{1 ? x} Sc_{1 + x} (MoO₄)₃ allows the phase of variable composition to be regarded as a promising sodiumion-conductive solid electrolyte.     

Raman spectroscopy investigation on (Pb1−xLax)(Zr0.90Ti0.10)1−x/4O3 ceramic system

A Raman spectroscopy study at room temperature was carried out on (Pb_1−xLa_x)(Zr_0.90Ti_0.10)_1−x/4O₃ ceramics (x = 2, 3, 4 at%). The results were analyzed considering the x-ray patterns at room temperature showing a mixture of two phases: a rombohedral-ferroelectric phase and an orthorhombic-antiferroelectric, increasing the% of the second one with the lanthanum concentration. For x = 3 at%, the analysis was also carried out in a wide temperature range. Two anomalies were evaluated, one around 363 K, which has been associated to a ferroelectric-antiferroelectric phase transition; the second one around 430 K, which has been associated to a transition from an incommensurable state to a ferroelectric phase.     

Hydrogen content in proton-conducting perovskites CaZr1 − x Sc x O3 − x /2 (x = 0.0–0.2)

The hydrogen content in CaZr_{1 ? x} Sc _x O_{3 ? x/2} (x = 0.00–0.20) and BaZr_0.9Y_0.1O_3-α (for comparison) was studied by powder nuclear microanalysis. The samples were saturated with heavy water (D₂O) vapors at 350 and 400°C in air. The chemical expansion of the CaZr_0.95Sc_0.05O_3-α and BaZr_0.95Y_0.05O_3-α samples at 700°C was measured at different water vapor pressures. A model was suggested to explain the lowered hydrogen content in oxides based on CaZrO₃.     

Atoms state and interatomic interactions in perovskite-like oxides: XXXII. Formation of paramagnetic clusters in the La1−0.33x Ca0.33x Fe x Al1−x O3 and La1−0.33x Sr0.33x Fe x Al1−x O3 solid solutions

Calcium- and strontium-containing lanthanum orthoferrites have been studied using magnetic dilution method. It has been shown that the iron-atom clusters with competing ferro- and antiferromagnetic exchange interactions can exist. By using Mossbauer spectroscopy, Fe(IV) atoms have been found in the La_1?0.33x Ca_0.33x Fe_xAl_1?x O₃ solid solutions and Fe(III) atoms in two different surroundings have been found in the La_1?0.33x Sr_0.33x Fe _x Al_1?x O₃ solid solutions. The compositions of paramagnetic clusters stable at the infinite dilution have been proposed basing of the magnetic susceptibility and Mossbauer spectroscopy data.     

Vibrational spectra and electrophysical properties of a NASICON phase of variable composition Na1 − x Co1 − x Sc1 + x (MoO4)3 (0 ≤ x ≤ 0.5)

Subsolidus phase ratios of the Na₂MoO₄-CoMoO₄-Sc₂(MoO₄)₃ system have been studied by X-ray diffraction, differential thermal analysis, and vibrational spectroscopy. A phase of variable composition Na_{1 ? x} Co_{1 ? x} Sc_{1 + x} (MoO₄)₃, 0 ≤ x ≤ 0.5 having NASICON structure (space group \(R\bar 3c\) ) and triple molybdate NaCo₃Sc(MoO₄)₅ crystallizing in triclinic system (space group \(P\bar 1\) ) have been obtained. The high conductivity of Na_{1 ? x} Co_{1 ? x} Sc_{1 + x} (MoO₄)₃ allows the phase of variable composition to be regarded as a promising sodium-ion conducting solid electrolyte.     

Multivariate analysis of melting points for homologous series C x H2x − 1NO (x = 3−6)

A multivariate analysis of the empirical structure data for isomeric homologues using principal-component analysis has been carried out, and the correlation with experimental melting points has been shown. Based on the data on the CSD structure, we discuss the impact of molecular H-aggregation.     

Electron microscopy study of the “cubic” perovskite phase SrFe1−xVxO2.5+x (0.05 ≤ x ≤ 0.1)

The oxygen-deficient “cubic” perovskite phase SrFe_1−xV_xO_2.5+x (0.05 ≤ x ≤ 0.10) quenched from 1473 K has been investigated by electron microscopy. Samples show a microdomain structure composed of ordered grains less than 20 nm. Oxygen vacancies form a brownmillerite-type superlattice in each microdomain, while six orientation variants have been observed within a particle; the oxygen vacancies in one domain are stringed along one of the six possible 〈110〉_C directions of the cubic host lattice. The domain size decreases as x or oxygen content increases. Vacancy arragements within the domains observed in high-resolution lattice images indicate that good structural coherence exists between microdomains and that a basic cubic perovskite skeleton is framed throughout a particle; they also suggest that vacancy content decreases in the boundary regions.     

Investigations of the LaGa1−xNixO3−δ (x < 0.50) system in the scope of SOFC's: synthesis and physical characterizations

The preparation and densification (95 %) of ceramics of the new solid solution LaGa_1−xNixO_3−δ have been carried out for x ≤ 0.50. The chemical analysis of the materials shows that both the oxygen nonstoichiometry amount (δ) and the electron carrier concentration increase with the substitution of nickel for gallium. Whereas LaGaO₃ is an insulator, the Ni-doped phases are semi-conducting and behave as a metal for the highest nickel contents. The dilatometric features versus temperature show these materials to be mechanically compatible with the electrolyte La_0.90Sr_0.10Ga_0.80Mg_0.20O_2.85. In addition their chemical composition does not change at high temperature. All these characteristics make these materials good candidates as cathodes for solid oxide fuel cells.     

Forms of oxygen in La1 − x Ca x MnO3 + δ (x = 0–1) perovskites and their reactivities in oxidation reactions

The effects of substitution in the cationic sublattice and of the synthesis procedure on the reactivity of different forms of oxygen in La_{1 ? x} Ca _x MnO_{3 + δ} perovskites synthesized by mechanochemical and ceramic processing was studied by temperature-programmed reduction (TPR) with hydrogen. As the calcium content of the perovskite is raised, the maxima of the TPR peaks shift to lower temperatures and the extent of reduction of the perovskite increase, implying an increase in the reactivity of the system. Conversely, raising the calcination temperature or extending the calcination time shifts the maxima of the peaks to higher temperatures and diminishes the extent of reduction of the sample. TPR data for the intermediate-composition samples can be explained in terms of the dependence of microstructure on the synthesis procedure (near-surface calcium segregation in the mechanochemically synthesized samples and the microheterogeneous structure of the ceramic samples). The reduction process Mn⁴⁺ → Mn²⁺ takes place in the low- and medium-temperature regions. According to the literature, the bulk reduction process Mn³⁺ → Mn²⁺ occurs at high temperatures. The activity of the system in CO oxidation is correlated with the amount of the most reactive surface oxygen, which is eliminated in hydrogen TPR runs below 250–300°C.