C60 growth on Si(100), GaSe(0001) and GeS(001)

C₆₀ films have been grown in ultra high vacuum on various crystalline substrates and the structure of the films has been investigated by low energy electron diffraction (LEED) and high resolution electron energy loss spectroscopy (HREELS). The C₆₀ films form randomly oriented nanocrystals on Si(100), mesoscopic polycrystals on GaSe(0001) and microscopic single crystals on GeS(001). The vibrational structure of the C₆₀/substrate interfaces is analyzed in detail by HREELS carried out in the dipole and impact scattering regimes. It is shown that the epitaxy of C₆₀ on GeS(001) is induced by the weak van der Waals bonding and the peculiar corrugation of the substrate surface.     

The effect of inhomogeneous dopant profiles on the electron energy loss spectra of Si(100)

Surface Plasmon excitations are measured by high resolution electron energy loss spectroscopy (HREELS) on highyln-doped, clean Si(100) wafers. After different annealing cycles at 900°C the plasmon loss shifts to lower loss energy. This effect can be quantitatively described by out-diffusion of the phosphorus dopant. The assumption of diffusion profiles and fits of calculated loss spectra to the experimental data allow a determination of the diffusion constant of phosphorus in silicon.     

Study of phase transitions within alumina grown on top of CoAl (1 0 0) surface

The oxidation of CoAl(1 0 0) was investigated by means of Auger electron spectroscopy (AES), low energy electron diffraction (LEED), high resolution electron energy loss spectroscopy (HREELS), and scanning tunneling microscopy (STM). In the case of alumina grown after oxidation with 15,000 L at room temperature, the characteristic EEL spectrum, along with the sharp (2 × 1) LEED pattern observed after annealing at 1000 K, showed that a stable well-ordered θ alumina was formed. The intermediate phase was found after heat treatment at 1150 K. At higher temperatures, the formation of the α-like alumina was observed. The comparative study of as-oxidation versus subsequent annealing of amorphous alumina at high-temperatures revealed a close similarity between the structures of alumina.     

Surface phonons of clean, hydrogen- and deuterium-terminated Si(0 0 1) surfaces

We present a comprehensive vibrational study of the clean and hydrogen- or deuterium-terminated silicon (0 0 1) surface. The modes related to the clean as well as to the H:Si, D:Si, and 2H:Si, 2D:Si surfaces are studied by means of high resolution electron energy loss spectroscopy (HREELS). We pay special attention to the modification of the phonon modes by the surface treatments and compare the data with reported experimental and theoretical results. The analysis of the relative phonon intensities of the clean, mono- and dihydride surfaces yields the assignment of the modes related to the dimer bonds. The isotopic shifts of vibrons related to the Si-H and Si-D bonds and to the surface phonon are discussed and applied to the characterisation of the surface excitations.     

The structures of physisorbed and chemisorbed formic acid on Si(1 1 1)-7 × 7

The reaction of formic acid on Si(1 1 1)-7 × 7 was investigated using X-ray photoelectron spectroscopy (XPS), ultraviolet photoelectron spectroscopy (UPS) and high-resolution electron energy loss spectroscopy (HREELS). The hydroxyl and carbonyl O 1s core levels of chemisorbed formic acid display chemical shifts of 2.4 and 0.2 eV respectively, compared with those of physisorbed molecules. The HREELS spectra of chemisorbed formic acid show the absence of stretching and bending modes of the O-H bond, the appearance of Si-H (2089 cm⁻¹) and the Si-O (680 cm⁻¹) stretching modes and the retained stretching mode of CO at 1703 cm⁻¹. Our results clearly suggest that formic acid dissociates to form monodentate formate species and H-atom on the adatom-rest atom pair of Si(1 1 1)-7 × 7.     

Adsorption and decomposition of triethylsilane on Si(1 0 0)

The adsorption and decomposition of triethylsilane (TES) on Si(1 0 0) were studied using temperature programmed desorption (TPD), high resolution electron energy loss spectroscopy (HREELS), electron stimulated desorption (ESD), and X-ray photoelectron spectroscopy (XPS). TPD and HREELS data indicate that carbon is thermally removed from the TES-dosed Si(1 0 0) surface via a β-hydride elimination process. At high exposures, TPD data shows the presence of physisorbed TES on the surface. These species are characterized by desorption of TES fragments at 160 K. Non-thermal decomposition of TES was studied at 100 K by irradiating the surface with 600 eV electrons. ESD of mass 27 strongly suggests that a β-hydride elimination process is a channel for non-thermal desorption of ethylene. TPD data indicated that electron irradiation of physisorbed TES species resulted in decomposition of the parent molecule and deposition of methyl groups on the surface that desorbed thermally at about 900 K. Without electron irradiation, mass 15 was not detected in the TPD spectra, indicating that the production of methyl groups in the TPD spectra was a direct result of electron irradiation. XPS data also showed that following electron irradiation of TES adsorbed on Si(1 0 0), carbon was deposited on the surface and could not be removed thermally.     

The interaction of H2S with Si(111) 7 × 7 surfaces by energy loss and Auger electron spectroscopies

Low energy electron loss spectroscopy (ELS) and Auger electron spectroscopy (AES) have been applied for the studies of the interaction of H₂S molecules with Si(111)7 × 7 surfaces. The observations are consistent with the interpretation that the room temperature non-dissociative adsorption state of H₂S molecules changes substantially after annealing at 550°C, resulting in the desorption of hydrogen and the covalent bond formation between silicon and sulfur atoms. The silicon disulfide films formed on Si(111) surfaces have been identified by the characteristic loss peaks in comparison with those of silicon dioxide.     

Me-PTCDI thin film deposition on InSb(1 1 1)A

The evolution of N,N′-dimethylperylene-3,4,9,10-dicarboxyimide (Me-PTCDI) thin films formed by vapour deposition on InSb(1 1 1)A substrates has been studied by X-ray photoelectron spectroscopy (XPS), high-resolution electron energy loss spectroscopy (HREELS) and low energy electron diffraction (LEED). XPS studies of the Me-PTCDI covered surface indicate that no significant interaction occurs at sub-monolayer coverage when compared to multilayer Me-PTCDI films. HREELS studies suggest only a weak interaction as evidenced by very small changes in the frequencies of several molecular vibrational modes. LEED patterns show the Me-PTCDI overlayer adopts a structure commensurate with the underlying InSb(1 1 1)A substrate surface and that can be rationalised by van der Waals intermolecular energy calculations for the Me-PTCDI unit cell. The results are consistent with a weak interaction at the Me-PTCDI/InSb interface, the formation of the commensurate structure being sufficient to overcome the small energetic penalty associated with deviation from the calculated intermolecular interaction energy minimum.     

Application of HREEL spectroscopy to characterize adsorbates on insulating metal oxide surfaces: carboxylates on MgO(100)

High resolution electron energy loss spectroscopy (HREELS) was used to characterize formate and acetate species adsorbed on the (100) surface of insulating MgO. Sample charging was eliminated using a low intensity, high energy electron beam and Fourier spectral deconvolution was used to remove phonon-phonon and phonon-adsorbate combination modes from the HREEL spectra. The results of this study demonstrate the applicability of HREELS in characterizing the vibrational properties of adsorbates on insulating metal oxide surfaces.     

用HREELS研究氢在GaAs和InP的(111),(111)表面上的吸附

氢在GaAs和InP表面上的吸附可以用高分辨率电子能量损失谱(HREELS)来探测。Ga—H,As—H,In—H和P—H键的伸缩振动各自对应于不同的能量损失。但是As—H振动极容易和Ga—H振动追加声子损失相混淆,只有从损失峰的相对强度比较上来区别。实验得到吸附的氢与表面原子的成键情况取决于表面的原子结构及电子分布。对于GaAs(111)面,低暴露量时只形成Ga—H键,而高暴露量时还可以形成As—H键。而InP(111)表面由于是经过磷气氛退火处理的,在低暴露量下In—H与P—H键均可形成。InP(Ⅲ)面上只看到P—H损失峰,说明这个表面是完全以P原子结尾的。在(Ⅲ)面上出现小面的情形,则表面Ⅲ族和Ⅴ族原子均可同氢成键。 关键词：     

用HREELS研究氢在GaAs和InP的（111），（III）表面上的吸附

氢在GaAs, 和InP 表面上的吸附可以用高分辨率电子能量损失谱(HREELS) 来探测.Ga-H侧, As-H , In-H 和P-H 键的伸缩振动各自对应于不同的能量损失. 但是A-H 振动极容易和Ga-H 振动追加声子损失相混淆, 只有从损失峰的相对强度比较上来区别。实验得到吸附的氢与表面原子的成键情况取决于表面的原子结构及电子分布. 对于GaAs (1 1 1)面, 低暴露量时只形成Ga-H 键, 而高暴露量时还可以形成As-H 键.而InP(1 1 1 ) 表面由于是经过磷气氛退火处理的, 在低暴露量下In 一H 与P一H 键均可形成. InP (III) 面上只看到P-H 损失峰, 说明这个表面是完全以P 原子结尾的. 在(1 1 1 ) 面上出现小面的情形, 则表面III族和V族原子均可同氢成键. 关键词：     

Chemically modified semiconductor surfaces: 1,4-phenylenediamine on Si(100)

The formation of inorganic/organic hybrid systems in ultra-high-vacuum (UHV) is studied for the adsorption of 1,4-phenylenediamine (PDA) and aniline on Si(100)(2 × 1) single crystal surfaces. X-ray photoemission spectra (XPS) of PDA and aniline adsorbed on silicon are interpreted in terms of an adsorbate configuration involving two covalent bonds between one amino group per molecule and the dangling bonds of the clean silicon surface. Vibrational high resolution electron energy loss spectroscopy (HREELS) allows us to identify the remaining amino groups in the PDA-adsorbate. Ultraviolet photoemission spectroscopy (UPS) and electron energy loss (EELS) data in the valence band range indicate that the aromatic ring stays intact after the chemisorption of PDA. Changes in work function and energetic shifts of the electronic transitions characterize the charge transfer between adsorbate and substrate. The experimental results are finally discussed in the framework of semi-empirical cluster calculations using MNDO-PM3.     

A HREELS study of the UV photon-induced chemistry of C6H5Cl adsorbed on Ag{111}

The UV photochemistry of both monolayer and multilayer C₆H₅Cl adsorbed on Ag{111} surfaces has been studied using high resolution electron energy loss spectroscopy (HREELS). Photon-induced dissociation via the cleavage of the CCl bonds was observed as a common feature. For the monolayer, chemisorbed biphenyl appears to be formed on the surface after photolysis at 110 K and subsequent annealing to 300 K. The two phenyl rings are found to lie parallel to the metal surface. The photon-induced dissociation of multilayer C₆H₅Cl leads, however, to photopolymerization as shown by the high thermal stability of the surface species formed and the detection of simple additive products in thermal desorption.     

Vibrational spectroscopy of oxygen on the (100) and (111) surfaces of lanthanum hexaboride

Reflection absorption infrared spectroscopy (RAIRS) and high resolution electron energy loss spectroscopy (HREELS) have been used to study the adsorption of oxygen on the (100) and (111) surfaces of lanthanum hexaboride. Exposure of the surface at temperatures of 95 K and above to O₂ produces atomic oxygen on the surface and yields vibrational peaks in good agreement with those observed in previous HREELS studies. On the La-terminated (100) surface, RAIRS peaks correspond to vibrations of the boron lattice that gain intensity due to a decrease in screening of surface dipoles that accompanies oxygen adsorption. A sharp peak at ～ 734 cm^?1 in the HREEL spectrum shows isotopic splitting with RAIRS into two components at 717 and 740 cm^?1 with full widths at half maxima of only 12 cm^?1. The sharpness of this mode is consistent with its interpretation as a surface phonon that is well separated from both the bulk phonons and other surface phonons of LaB₆. On the boron-terminated LaB₆(111) surface, broad and weak features are assigned to both vibrations of the boron lattice and of boron oxide. On the (100) surface, oxygen blocks the adsorption sites for CO, and adsorbed CO prevents the dissociative adsorption of O₂.     

Adsorption of nitrogen-containing aromatic molecules on Si(1 1 1)-7 × 7

The adsorption configurations of pyrimidine and triazine on Si(1 1 1)-7 × 7 were investigated using high-resolution electron energy loss spectroscopy (HREELS) X-ray photoelectron spectroscopy and density functional theory calculations. The HREELS spectra of chemisorbed monolayer show the coexistence of the C(sp²)-H and C (sp³)-H stretching modes together with the observation of the unconjugated CN(C) vibrational feature suggesting that the carbon atom and its para-nitrogen atom of pyrimidine and triazine directly participate in binding with the surface to form Si-C and Si-N σ-linkages. The core levels of the C-atom and its opposite nitrogen atom directly binding with Si-atoms experience a down-shifting by 1.8-1.9 and 1.4-1.6 eV, respectively. These experimental findings are consistent with the density functional theory calculations indicating that the carbon atom and its para-nitrogen atom favorably link with the adjacent adatom and rest atom pair to form C-Si and N-Si linkages.     

HREELS study of the adsorption and evolution of diethylamine (DEA) on Si(1 0 0) surfaces

The adsorption of diethylamine (DEA) on Si(1 0 0) at 100 K was investigated using high-resolution electron energy loss spectroscopy (HREELS) and electron stimulated desorption (ESD). The thermal evolution of DEA on Si(1 0 0) was studied using temperature programmed desorption (TPD). Our results demonstrate DEA bonds datively to the Si(1 0 0) surface with no dissociation at 100 K. Thermal desorption of DEA takes place via a β-hydride elimination process leaving virtually no carbon behind. Electronic processing of DEA/Si(1 0 0) at 100 K results in desorption of ethyl groups; however, carbon and nitrogen are deposited on the surface as a result of electron irradiation. Thermal removal of carbon and nitrogen was not possible, indicating the formation of silicon carbide and silicon nitride.     

Growth and vibrational properties of MnOx thin films on Rh(111)

The growth, structures, and vibrational properties of ultrathin manganese oxide films on Rh(111) had been investigated using high-resolution electron energy loss spectroscopy (HREELS), X-ray photoelectron spectroscopy (XPS), low energy electron diffraction (LEED), low energy ion scattering spectroscopy (LEIS) and Auger electron spectroscopy (AES). MnO_x grew in a layer-by-layer fashion on the Rh(111) surface. HREELS phonon features and XPS binding energies showed that an OMnO like tri-layer formed initially. Which was stable on the Rh(111) surface with MnO_x coverage less than one monolayer. At above one monolayer, Mn₃O₄ was preferred as indicated from a four-phonon feature peaked at 13.3, 39, 68 and 83 meV in HREELS. Higher temperature oxidation and annealing were found to improve the long-range order of the MnO_x films.     

氧在GaP(111)上的初级吸附阶段

采用多种表面分析手段,系统地研究了氧在GaP(111)上的吸附,发现氧的初级吸附在1×10⁴L时就已饱和,获得了有关这一阶段表面电子结构的变化、表面能带弯曲、化学吸附反应等方面的信息,发现这一吸附阶段与表面缺陷有关,适当地加热处理则可能将缺陷和氧一同去除,因此这有可能成为一种有效的、去除缺陷的表面工程手段。 关键词：     

Fuchs-Kliewer phonon spectrum of Co3O4(110) single crystal surfaces by high resolution electron energy loss spectroscopy

The Fuchs-Kliewer phonon spectrum of single crystal Co₃O₄(110) has been analyzed by high resolution electron energy loss spectroscopy (HREELS) and the four fundamental phonon losses have been identified at 26.8, 47.5, 71.1 and 84.7 meV (216, 383, 573 and 683 cm⁻¹). This is the first HREELS study reported for an intrinsic spinel single-crystal surface with primary focus on the Fuchs-Kliewer phonon structure. The Co₃O₄ crystal is first characterized by Auger electron spectroscopy (AES), X-ray photoelectron spectroscopy (XPS) and low-energy electron diffraction (LEED), which establish the composition, cleanliness, and order of the (110) surface. Electron scattering is then used to obtain a series of well-resolved Fuchs-Kliewer phonon spectra over 2.25-14.25 eV incident electron energy range. The variation in phonon intensity with primary beam energy is shown to agree with that predicted by dielectric theory.     

Complex formation and proton transfer between formic acid and water adsorbed on Au(111) surfaces under UHV conditions

The coadsorption of formic acid and water on Au(111) surfaces has been investigated by means of vibrational and photoelectron spectroscopy (HREELS, XPS). Formic acid adsorbs at 90 K molecularly with vibrational modes characteristic for flat lying zig-zag chains in the mono- and multilayer regime, like in solid formic acid. Annealing results in a complete desorption at 190 K. Sequential adsorption of formic acid and water at 90 K shows no significant chemical interaction. Upon annealing the coadsorbed layer to 140 K a hydrogen-bonded cyclic complex of formic acid with one water molecule could be identified using isotopically labelled adsorbates (D₂O, H¹³COOD). Upon further annealing this complex decomposes leaving molecularly adsorbed formic acid on the surface at 160 K, accompanied by a proton exchange between formic acid and water. PACS 68.08.-p; 68.43.-h; 68.43.Pq