Growth of α-NiSO<Subscript>4</Subscript> · 6H<Subscript>2</Subscript>O crystals at high rates

The high-rate growth of nickel sulfate hexahydrate NiSO₄ · 6H₂O (α-NSH) crystals up to 120 × 120 × 65 mm³ in size is described for the first time. The data on the distribution of related impurities in the {011} and {001} growth sectors of α-NSH crystals grown at different rates are reported. The transmission spectra of both growth sectors of these crystals are obtained. The structural quality and the optical properties of rapidly and slowly grown α-NSH crystals are compared. It is established that the {011} growth sector of crystals grown at rates exceeding 5 mm/day shows the best characteristics for application in UV filters.     

Structural Conditionality of the Ionic Conductivity of MTiORO<Subscript>4</Subscript> (M = K,Rb; R = P,As) Single Crystals

The ionic conductivity σ_||c along the crystallographic axis c and the structural imperfection of the lattices of KTiOPO₄, RbTiOPO₄, and RbTiOAsO₄ single crystals with low defect concentration, grown by the high temperature solution growth technique, have been investigated by impedance spectroscopy and X-ray diffraction analysis. Isomorphic substitutions of Rb⁺ ions for conduction K⁺ cations in MTiOPO₄ crystals decreases the σ_||c value, whereas the substitution of As⁵⁺ ions for framework P⁵⁺ cations in RbTiORO₄ crystals increases the σ_||c value. The σ_||c values at 573 K are found to be 1.0 × 10^–5, 5.7 × 10^–6, 2.0 × 10^–6, and 3.3 × 10^–5 S/cm for the KTiOPO₄, RbTiOPO₄ {100}, RbTiOPO₄ {201}, and RbTiOAsO₄ crystals, respectively (the growth zone of the crystalline boule from which the samples were cut is indicated in braces).     

The Influence of Cation Substitution on the Kinetics of Phase Transitions in Crystals of (K,NH<Subscript>4</Subscript>)<Subscript>3</Subscript>H(SO<Subscript>4</Subscript>)<Subscript>2</Subscript> Solid Solutions

The structure of (K_0.967(NH₄)_0.033)₃H(SO₄)₂ crystals, belonging to the K₃H(SO₄)₂–(NH₄)₃H(SO₄)₂–H₂O salt system, has been investigated by X-ray structural analysis. The room-temperature characteristics of the atomic structure of these crystals are found to be as follows: sp. gr. C2/c, Z = 4, a = 14.7025(4) Å, b = 5.6859(2) Å, c = 9.7885(3) Å, and R/wR = 0.021/0.030%. The thermal and optical properties of (K,NH₄)₃H(SO₄)₂ and K₃H(SO₄)₂ single crystals have been investigated and compared in a temperature range of 295–500 K.     

Hydrothermal Synthesis and Structure of Fe<Subscript>6.36</Subscript>Mn<Subscript>0.64</Subscript>(PO<Subscript>3</Subscript>(OH))<Subscript>4</Subscript>(PO<Subscript>4</Subscript>)<Subscript>2</Subscript>

Abstract  

Single crystals of iron and manganese phosphate Fe_6.36Mn_0.64(PO₃(OH))₄(PO₄)₂ was synthesized by hydrothermal method. The compound crystallizes in the Fe₇(PO₄)₆ structure type and is isotypic with the solid solution \textM_{7 - \textx} \textM_\textx^￠ ( \textHPO₄ )₄ ( \textPO₄ )₂ {\text{M}}_{{7 - {\text{x}}}} {\text{M}}_{\text{x}}^{\prime} \left( {{\text{HPO}}_{4} } \right)_{4} \left( {{\text{PO}}_{4} } \right)_{2} where M is Fe, Co, Mg, Mn. The compound is triclinic, P-1, a = 6.571(5), b = 7.993(3), c = 9.547(2) Ǻ, α = 103.97(1)°, β = 109.29(2)°, γ = 101.57(3)°. The structure is based on a three-dimensional framework of distorted edge-sharing MO₆ and MO₅ polyhedra, forming infinite chains, which are interlinked by corner-sharing with PO₄ tetrahedra. The formula unit is centrosymmetric, with all atoms in general positions except for one Fe atom, which has site symmetry −1.     

Synthesis and Crystal Structure of La(NO<Subscript>2</Subscript>)(SO<Subscript>4</Subscript>)(H<Subscript>2</Subscript>O)

Abstract Single crystals of new open-framework lanthanide sulphate nitrite La(NO₂)(SO₄)(H₂O) has been synthesized, in the presence of 2,6-diformyl-4-chlorophenol. His structure has been determined by X-ray diffraction data: the complex crystallizes in the tetragonal system, space group P4₃, with a = 7.0028(2) (?), b = 7.0028(2) (?), c = 11.8341(4) ?, V = 580.34(3) ?³, Z = 4, D _c = 3.582 Mg m⁻³. The three-dimensional (3D) framework of this compound is built up by the linkages of lanthanide atoms and the oxygen atoms of the sulphate and nitrite groups. The lanthanum atom is 9-fold coordinated. The structure is unfamiliar in lanthanide chemistry and this compound represents the first example of nitrite lanthanide sulphate complex. Graphical Abstract An unfamiliar structure in lanthanide chemistry represented by the first example of nitrite lanthanide sulphate complex is described.      

The effect of metallic ions on tapering phenomenon of DKDP crystals and its elimination

The anomalous wedge‐like shape of KH₂PO₄‐type single crystal, also called tapering, is discussed in this paper. DKDP single crystals grew on seeds from the solutions containing high concentrations of Al³⁺, Fe³⁺ and Cr³⁺ impurities. The tapering phenomenon occurred on the prismatic {010} faces, and the tapering angle θ was nearly measured as 10°. We adjusted the pD value of the solution from 3.0 to 4.2 by adding K₂CO₃, the tapering angle of DKDP crystal grown from the same solution at same supercooling was reduced to 0°. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Synthesis,physical properties,and atomic structure of niobium-doped RbTiOPO<Subscript>4</Subscript> crystals

Single crystals of solid solutions Rb_1?xTi_1?xNb_xOPO₄(RTP: Nb) were grown and the temperature dependences of their dielectric and nonlinear optical properties and electric conductivity were studied. The maximum possible niobium content in these crystals is close to x = 0.1. The niobium impurities decelerate growth of {100} faces, and crystals take a plate-like habit. With increasing doping level, ferroelectric phase transitions diffuse and their temperature decreases. A specific feature of the dielectric properties of RTP: Nb crystals is the appearance of a broad relaxation maximum ε₃₃ in the temperature range 200–600°C caused by the formation of vacancies in the rubidium cation sublattice. The intensity of second-harmonic generation under laser irradiation decreases with increasing niobium content. The atomic structure of a crystal with x = 0.01 is studied and it is established that niobium substitutes for titanium only in Ti(1) positions.     

Twinning Morphologies and Mechanisms of β-BaB2O4 (BBO) Crystal Grown by TSSG Method

The twinning morphology of β-BaB₂O₄ crystal grown by TSSG has been studied on the basis of crystallography. It was found that the faces R{101-2} and r{011-4} are often intergrown together by either r{011-4} intergrown in R{101-2} or in reverse, two individuals mostly take X(112-0) and occasionally take Y(011-0) as twin boundary; and that two individuals in the twin could take the same or opposite crystallographic polarity, this was identified by surface etched figures and the piezoelectric measurements. The formation of the twinned crystals are discussed from the crystallographic structural characteristics and the energetic considerations. The experimental factors such as crystal seed quality are suggested to reduce or eliminate the twin formation and to improve the crystal quality.     

Investigation of the structural conditionality for changes in physical properties of K<Subscript>3</Subscript>H(SO<Subscript>4</Subscript>)<Subscript>2</Subscript> crystals

With the aim of elucidating the nature of anomalies in the physical properties of K₃H(SO₄)₂ crystals that arise as the temperature grows, the dielectric and optical properties of the crystals are studied, an X-ray diffraction analysis of single-crystal and polycrystalline specimens are performed, and the morphology and chemical composition are studied by scanning electron microscopy and energy-dispersive X-ray spectroscopy. As a result of the studies performed, a phase transition from the phase with the monoclinic symmetry (space group C2/c) to the phase with the trigonal symmetry (space group R $ \bar 3 $ \bar 3 m) is found in a number of K₃H(SO₄)₂ specimens at a temperature of ≈457 K, the responsibility of the dynamically disordered hydrogen-bond system for the rise of high proton conductivity in the high-temperature phases of the crystals of this family is confirmed, and data on the solid-phase reactions proceeding at high temperatures are obtained.     

Growth‐Sector Boundaries and Growth‐Rate Dispersion in Potassium Alum Crystals

Crystals of potassium alum, pure and slightly doped with Cr³⁺, were grown from aqueous solution by slow temperature lowering. In addition, short re‐dissolution periods were introduced in order to provoke growth defects and changes of growth rates. Crystal slices of about 1 mm thickness were studied by conventional LANG X‐ray diffraction topography using MoKα radiation. For Cr‐doped crystals, boundaries between {100}, {100} and {111} growth sectors appear by pronounced dynamical X‐ray topographic contrast similar to that of stacking faults. Re‐dissolution experiments provoke the formation of inclusions on {100} faces, followed by an increase of the {100} growth rate by the factor of about six, relative to the neighboured {111} faces. X‐ray topographs show that this increase is correlated with the formation of dislocations, which interestingly have pure‐edge character. During further growth these dislocations penetrate the {100}‐{111} growth sector boundary and vanish from the {100} face, which slows down and finally adopts its former growth rate before re‐dissolution.     

The Changes of Thermal,Dielectric, and Optical Properties at Insertion of Small Concentrations of Ammonium to K<Subscript>3</Subscript>H(SO<Subscript>4</Subscript>)<Subscript>2</Subscript> Crystals

The structure of (K_1–x(NH₄)_x)₃H(SO₄)₂ crystals with a low ammonium concentration and the behavior of their thermal, optical, and dielectric properties in a temperature range of 275–500 K have been investigated to clarify the influence of doping on the phase transition kinetics. An examination of unit-cell parameters of (K_{1 – x}(NH₄)_x)₃H(SO₄)₂ single crystals has confirmed the existence of a superprotonic phase transition at a temperature of ≈450K. The conducting properties of single-crystal and polycrystalline samples have been studied.     

The Morphology of Hydrothermally Grown Plagioclase

Plagioclase crystals Ab₂₀An₀₀ and nearly pure anorthite were grown on the surface of artificial melts by hydrothermal treatment at 2 kb. The average crystal size was 0.002 to 0.008 mm. In the temperature range of 400° to 600°C a pseudohexagonal habit was observed for anorthite while a lath-like habit due to the prevalence of {010} was found for the Ab₂₀An₈₀ composition. Dominating faces are {010} {130} {110} {100} {110} {130} in the zone [001] and {021} {111} {111} {021} {111} {111} together with {001}.     

Correlation of the structural imperfection and morphology of Bi<Subscript>4</Subscript>Ge<Subscript>3</Subscript>O<Subscript>12</Subscript> crystals grown by the low-gradient Czochralski method

This paper reports on the results of investigations into the morphological structure of the facets of Bi₄Ge₃O₁₂ crystals grown by the Czochralski method under the conditions of low temperature gradient (0.1–1 K/cm). A correlation between the morphological features of the facets at the crystallization front and the formation of defects in the bulk of the crystal is revealed. It is demonstrated that the {112} facets remain regular while the growing surface deviates from the (112) crystallographic plane by an angle of up to 1°. At larger deviations, there occurs a crossover from the stable facet growth to the growth of macrosteps or normal growth depending on the growth conditions.     

Microstructures on {111} faces of stannic iodide single crystals

Single crystals of stannic iodide (SnI₄) havebeen grown using the controlled reaction between SnCl₂ and KI by diffusion process in silica gel medium. Orange to reddish octahedral stannic iodide crystals up to 3–4 mm in size have been grown at room temperature. Optical studies have been made on the various surface structures of {111} faces of the asgrown crystals. On octahedral faces of these crystals, triangular-shaped hillocks with growth layers in the 〈110〉 directions have been observed. Occasionally, growth spirals on octahedral faces have also been reported. Close loops of growth fronts have been investigated and have been interpreted. It has been suggested that two-diemensional nucleation, spreading and pilling up of triangular growth layers is mainly responsible for the growth and occasionally the growth is due to screw dislocations. The implications are discussed.     

Microstructures of Tin Iodide Single Crystals Grown in Silica Gels

Single crystals of tin iodide (SnI₂) have been grown in silica gels. A detailed microtopographical study of {100} faces have been described. Horizontal striations are predominant on these faces for most of the crystals, while few of them show vertical striations. The horizontal striations are associated with the two-dimensional nucleation theory whereas the vertical striations relate to the growth fronts. Growth layers modified by the presence of misaligned microcystals have been illustrated. The natural etch pits on {100} faces of the crystal are attributed to the dissolution of crystals in the acid set gel. In the light of these observations, the mechanism of the development and growth of these faces have been assessed and the implications are discussed.     

The cubic space group of tungstogallate acid,H<Subscript>5</Subscript>GaW<Subscript>12</Subscript>O<Subscript>40</Subscript>

The space group of tungstogallate acid, H₅GaW₁₂O₄₀, reported by Niu et al. (J. Chem. Crystallogr. 2003, 33, 799) should be I–43m instead of Cm; the monoclinic C-centered cell is transformed to the I-centered cubic cell by (1 0 0; ,– , 1; – , – , –1).     

Growth and morphological study of copper oxide single crystals

Experiments on the growth of CuO single crystals by crystallization from flux in the CuO-Bi₂O₃-PbO-PbF₂, CuO-Bi₂O₃-Li₂O, CuO-Bi₂O₃-B₂O₃, CuO-BaO-Y₂O₃, and CuO-MO_x systems (M = P, V, or Mo) have been performed. The best results were obtained in crystallization in the CuO-Bi₂O₃-PbF₂ system: prismatic single crystals of platelet-and needlelike or isometric habit with dimensions up to 1 × 10 × 10, 1 × 1 × 20, or 6 × 6 × 8 mm, respectively, have been grown. The CuO crystals show polysynthetic twinning in the form of numerous alternating light and dark bands bound by systems of parallel straight lines on the {110} and {111} faces. A possible model of twinning associated with the Cu₂O → CuO transformation is considered.     

Growth and properties of mixed K2Ni x Co1−x (SO4)2 · 6H2O crystals

Optically homogeneous mixed K₂Ni _x Co_{(1 ? x)}(SO₄)₂ · 6H₂O crystals are grown from solutions of different compositions by the temperature-reduction technique in static and dynamic regimes. The optical characteristics of the grown crystals are measured: transmittance reaches 80% in the wavelength range of 240–290 nm and no more than 9% in the visible spectral range. The thermal stability of the crystals is studied. It is established that the thermal stability of mixed K₂Ni _x Co_{1 ? x} (SO₄)₂ · 6H₂O crystals is higher than that of K₂Co(SO₄)₂ · 6H₂O crystal. The defects of the mixed crystals grown in static and dynamic regimes are investigated by X-ray topography.     

Growth and etching of calcite crystals

Single crystals of calcite (CaCO₃) have been grown by the method employed by GRUZENSKY , using an aquoeus solution of CaCl₂ and a solid (NH₄)₂SO₃, The chemical reaction takes place according to the following equation: CaCl₂ + (NH₄)₂SO₃ CaCO₃ + 2 NH₄Cl The crystals grown by this method are about 0.2 to 0.8 mm in edge dimensions. Synthetic calcite crystals have been cleaved along (100) planes and the cleavage surfaces have been studied by multiple beam interferometry. The interferograms have revealed that the cleavages are quite flat. The cleavage faces have also been chemically etched and the etch patterns studied optically. By etching a cleavage successively for three different periods it was found that the bottoms of the point-bottomed pits follow a linear etch path. By etching a cleavage pair, one face in one etchant and the other face in a different etchant and by comparing the etch patterns produced, before and after polishing a cleavage face it has been shown that the etch pits nucleate at the sites of dislocations in the crystal. The etch patterns have also been compared with those produced on the cleavage faces of natural crystals. The density of dislocations in the syntheitc calctie crystals was generally less than the density of dislocations in the natural calcite crystals. The implications have been discussed.     

水热法合成Zn1-xMnxO稀磁半导体

本文采用水热法在430℃,以3mol%.L-1KOH作矿化剂,填充度为35%,反应时间24h,合成了Zn1-xMnxO稀磁半导体晶体。所合成晶体具有ZnO纤锌矿结构,晶面显露正极面{0001}、负极面{0001}、菱面{1011}及负菱面{1011}晶体高度为5~30μm,径高比约为2:1。X荧光能谱(EDS)显示Mn原子百分浓度为2.6%(x=0.026)。晶体呈现低温铁磁性,居里温度50K。