An electropolymerized aniline-based fiber coating for solid phase microextraction of phenols from water

An aniline-based polymer was electrochemically prepared and applied as a new fiber coating for solid phase microextraction (SPME) of some priority phenols from water samples. The polyaniline (PANI) film was directly electrodeposited on the platinum wire surface in sulfuric acid solution using cyclic voltammetry (CV) technique. The efficiency of new coating was investigated using a laboratory-made SPME device and gas chromatography with flame ionization detection for the extraction of some phenols from the headspace of aqueous samples. The scanning electron microscopy (SEM) images showed the homogeneity and the porous surface structure of the film. The results obtained proved the ability of this polymer as a suitable SPME fiber coating for trapping the selected phenols. Influential parameters affecting the extraction process were optimized and an extraction time of 50 min at 50 °C gave maximum efficiency, when the aqueous sample was saturated with NaCl and adjusted at pH 2. This new coating can be prepared easily in a reproducible manner and it is rather inexpensive and stable against most of organic solvents. The PANI thickness can be precisely controlled by the number of CV cycles. At the optimum conditions, the R.S.D. for a double distilled water spiked with phenol and chlorophenols at ppb level were 4.8-17% (n = 3) and detection limits for the studied compounds were between 0.69 and 3.7 ng ml⁻¹, except for phenol and 4-chlorophenol. The optimized method was successfully applied to some real-life water samples.     

A sol‐gel based solid phase microextraction fiber for the analysis of aliphatic alcohols in apple juices

A new fiber based on titania‐chitin sol‐gel coated on a silver wire for the headspace solid phase microextraction of aliphatic alcohols from apple juice samples was developed. The influences of fiber coating composition and microextraction conditions (extraction temperature, extraction time, and ionic strength of the sample matrix) on the fiber performance were investigated. Also, the influence of temperature and time on desorption of analytes from fiber were studied. Under the optimized conditions, a porous fiber with a high extraction capacity and good thermal stability (up to 250°C) was obtained. The proposed headspace solid‐phase microextraction‐GC method was successfully used for the analysis of aliphatic alcohols in apple juice and concentrate samples. The recovery values were from 92.8 to 98.6%. The RSD (n=5) for all analytes were below 7.8%.     

Vacuum-assisted headspace solid phase microextraction of polycyclic aromatic hydrocarbons in solid samples

For the first time, Vacuum Assisted Headspace Solid Phase Microextraction (Vac-HSSPME) is used for the recovery of polycyclic aromatic hydrocarbons (PAHs) from solid matrices. The procedure was investigated both theoretically and experimentally. According to the theory, reducing the total pressure increases the vapor flux of chemicals at the soil surface, and hence improves HSSPME extraction kinetics. Vac-HSSPME sampling could be further enhanced by adding water as a modifier and creating a slurry mixture. For these soil-water mixtures, reduced pressure conditions may increase the volatilization rates of compounds with a low K_H present in the aqueous phase of the slurry mixture and result in a faster HSSPME extraction process. Nevertheless, analyte desorption from soil to water may become a rate-limiting step when significant depletion of the aqueous analyte concentration takes place during Vac-HSSPME. Sand samples spiked with PAHs were used as simple solid matrices and the effect of different experimental parameters was investigated (extraction temperature, modifiers and extraction time). Vac-HSSPME sampling of dry spiked sand samples provided the first experimental evidence of the positive combined effect of reduced pressure and temperature on HSSPME. Although adding 2 mL of water as a modifier improved Vac-HSSPME, humidity decreased the amount of naphthalene extracted at equilibrium as well as impaired extraction of all analytes at elevated sampling temperatures. Within short HSSPME sampling times and under mild sampling temperatures, Vac-HSSPME yielded linear calibration curves in the range of 1–400 ng g⁻¹ and, with the exception of fluorene, regression coefficients were found higher than 0.99. The limits of detection for spiked sand samples ranged from 0.003 to 0.233 ng g⁻¹ and repeatability from 4.3 to 10 %. Finally, the amount of PAHs extracted from spiked soil samples was smaller compared to spiked sand samples, confirming that soil could bind target analytes more strongly and thus decrease the readily available fraction of target analytes.     

Silicone glue based solid phase microextraction fiber for amino acid determination

A solid phase microextraction fiber based on high temperature silicone glue coated on a stainless steel wire is presented for use in the extraction of amino acid derivatives. Amino acids were derivatizad using ethyl chloroformate. Effects of the extraction and desorption parameters including extraction and desorption time, desorption temperature and ionic strength on the extraction/desorption efficiency have been studied and quality parameters of the method were measured. A possibility to apply the proposed method for the identification of proteinaceous binders was demonstrated.     

Improvement of solid phase microextraction fiber assembly and interface for liquid chromatography

Modifications were made on commercial SPME fiber assembly and SPME–LC interface to improve the applicability of SPME for LC. Polyacrylonitrile (PAN)/C18 bonded fuse silica was used as the fiber coating for LC applications because the fiber coating was not swollen in common LC solvents at room temperature. The inner tubing of SPME fiber assembly was replaced with a 457 μm outside diameter (o.d.) solid nitinol rod. And the coated fiber (o.d. 290 μm) was installed onto the nitinol rod. The inner diameter (i.d.) of the through hole of the ferrule in the SPME–LC interface was enlarged to 508 μm to accommodate the nitinol rod. The much larger inner rod protected the fiber coating from being stripped when the fiber was withdrawn from the SPME–LC interface. The system was evaluated in term of pressure test, desorption optimization, peak shape, carryovers, linear range, precision, and limit of detection (LOD) with polycyclic aromatic hydrocarbons (PAHs) as the test analytes. The results demonstrated that the improved system was robust and reliable. It overcame the drawbacks, such as leak of solvents and damage of fiber coatings, associated with current SPME fibers and SPME–LC interface. Another sealing mechanism was proposed by sealing the nitinol rod with a specially designed poly(ether ether ketone) (PEEK) fitting. The device was fabricated and tested for manual use.     

Comparison of solid phase microextraction and hollow fiber liquid phase microextraction for the determination of pesticides in aqueous samples by gas chromatography triple quadrupole tandem mass spectrometry

This work compares two miniaturised sample preparation methods, solid phase microextraction (SPME) and hollow fiber liquid phase microextraction (HF-LPME), in combination with gas chromatography coupled to tandem mass spectrometry with a triple quadrupole analyzer for the determination of 77 pesticides in drinking water. In the case of SPME, extraction temperature and time were optimized by experimental design, although other parameters, as desorption time, pH, and ionic strength, were also evaluated. The extraction and desorption solvents [octanol/dihexyl ether (75:25, v/v) and cyclohexane, respectively], as well as the extraction and desorption time, ionic strength, and pH, were studied for the HF-LPME procedure. Under the optimal conditions, recoveries (70.2–113.5% for SPME and 70.0–119.5% for HF-LPME), intra-day precision (2.1–19.4% for SPME and 4.3–22.5% for HF-LPME), inter-day precision (5.2–21.5% for SPME and 8.4–27.3% for HF-LPME), and limits of detection, between 0.1 and 28.8 ng/L for SPME and 0.2 and 47.1 ng/L for HF-LPME and overall uncertainty (9.6–25.2% for SPME and 13.3–27.5% for HF-LPME) were established for both extraction procedures. Finally, the proposed methods were successfully applied to the analysis of 41 drinking water samples, and similar results were obtained with both extraction approaches.     

Polyaniline-polypyrrole coating for solid phase microextraction

A procedure for direct electrochemical deposition of polyaniline-polypyrrole blend coating on the surface of stainless steel wire was suggested. Incorporation of polyaniline and polypyrrole into the blend coating was confirmed by infrared spectroscopy. Key parameters (pyrrole, aniline, dopant and sulphuric acid concentrations and deposition potential) influencing the coating’s mechanical stability and surface homogeneity were optimised and thermostability of the coating was investigated. A possibility to apply the coating as a new fibre for solid phase microextraction was demonstrated. The coating showed better selectivity toward aromatic, hydrophobic compounds.      

Effective extraction of triazines from environmental water samples using magnetism-enhanced monolith-based in-tube solid phase microextraction

This article reports on the effective extraction of triazines from environmental water samples using magnetism-enhanced monolith-based in-tube solid phase microextraction (ME-MB/IT-SPME). Firstly, monolithic poly (octyl methacrylate-co-ethyleneglycol dimethacrylate) capillary column doped with magnetic nanoparticles was synthesized inside a fused silica. After that, the monolithic capillary column was placed inside a magnetic coil that allowed the exertion of a variable magnetic field during adsorption and desorption steps. The effects of intensity of magnetic field, adsorption and desorption flow rate, volume of sample and desorption solvent, pH value and ionic strength in sample matrix on the performance of ME-MB/IT-SPME for triazines were investigated in details. Under the optimized conditions, the developed ME-MB/IT-SPME showed satisfactory quantitative extraction efficiencies of the target analytes between 64.8% and 99.7%. At the same time, the ME-MB/IT-SPME was combined with high-performance liquid chromatography with diode array detection to detect six triazines in water samples. The limits of detection (S/N = 3) and limits of quantification (S/N = 10) were in the ranges of 0.074–0.23 μg/L and 0.24–0.68 μg/L, respectively. The precision of the proposed method was evaluated in terms of intra- and inter-assay variability calculated as relative standard deviation, and it was found that the values were all below 10%. Finally, the developed method was successfully applied for environmental water samples such as farmland, lake and river water with spiked recoveries in the range of 70.7–119%.     

Analysis of n-alkanes at sub microgram per liter level after direct solid phase microextraction from aqueous samples.

This work describes the application of the previously presented solid phase microextraction (SPME) fiber in direct mode for sampling of C10-C20 n-alkanes from aqueous solution. The fiber has simple composition and is constructed from activated charcoal:PVC suspension in tetrahydrofuran. When the composition of the fiber was optimized that the optimum composition was 90:10 (activated charcoal:PVC) for direct mode, whereas it was 75:25 for sampling from the headspace of aqueous samples. This fiber is completely stable in contact with water. The extraction efficiency is improved in the presence of 0.1 M NaCl. The value is between 17.8-38.5% for the first extraction, which better than the efficiency of similar commercial fibers. After seven extractions, all analytes are removed from the aqueous samples nearly 100%. Single fiber repeatability and fiber-to-fiber reproducibility are good and both are less than 13% for all studied alkanes. Finally, direct mode SPME was used in the determination of n-alkanes in the range of sub microg L(-1) without any additional preconcentration procedure. Gas chromatography along with flame ionization detection were used for separation and detection of the studied analytes.     

Ultrathin phenyl-functionalized solid phase microextraction fiber coating developed by sol-gel deposition

A new sol-gel application for the development of SPME fibers is described. Phenyltrimethoxysilane (PTMOS) and methyltrimethoxysilane (MTMOS) were the sol-gel precursors used at different proportions, together with different water contents, catalyst and reaction time. It was observed that obtaining a good film quality was determinant for a good extracting fiber performance. The film thickness ranged 0.2-1 microm and could not be increased by multi-coating processes. Apparently, a dense, non-porous microstructure was obtained. These coatings exhibited a strong hydrophobic character, as shown by the capability of extraction of long chain and apolar aromatic compounds, which, was comparable to that of the 100 microm polydimethylsiloxane (PDMS) and 65 microm carbowax-divinylbenzene (CW-DVB). The developed fiber has shown high thermal (350 degrees C) and organic solvent stability (ethanol, toluene and dichloromethane), thus bearing adequate characteristics to be associated to GC and potentialities that may also envisage suitability for HPLC. The new fibers may be useful for the microextraction of non-polar compounds, although at trace levels and in simple matrixes only, due to the susceptibility to competition.     

Headspace solid phase microextraction for screening for the presence of resins in Egyptian archaeological samples

The aim of this study was to use headspace solid phase microextraction (SPME) to reveal the presence of resin in archaeological samples, such as mummification balms, from ancient Egypt. Experiments were first performed with fresh resins of known origin. The SPME fibre readily extracted mono- and sesquiterpenes and, to a lesser extent, diterpenes. Using mass spectra and retention indices of constitutive compounds, qualitative analysis of the volatile fraction allowed us to differentiate resins or gum-resins such as myrrh, olibanum, galbanum, labdanum, mastic, and conifer resins. SPME was then successfully applied to archaeological samples from ancient Egypt in which the presence of resins was detected. Volatile components were desorbed and trapped according to the same SPME procedure as was applied to fresh resins, after a sample preparation consisting of a fine grinding.     

Analysis of organic compounds in environmental samples by headspace solid phase microextraction

The analysis of samples contaminated by organic compounds is an important aspect of environmental monitoring. Because of the complex nature of these samples, isolating target organic compounds from their matrices is a major challenge. A new isolation technique, solid phase microextraction, or SPME, has recently been developed in our laboratory. This technique combines the extraction and concentration processes into one step; a fused silica fiber coated with a polymer is used to extract analytes and transfer them into a GC injector for thermal desorption and analysis. It is simple, rapid, inexpensive, completely solvent-free, and easily automated. To minimize matrix interferences in environmental samples, SPME can be used to extract analytes from the headspace above the sample. The combination of headspace sampling with SPME separates volatile and semi-volatile analytes from non-volatile compounds, thus greatly reducing the interferences from non-target compounds. This paper reports the use of headspace SPME to isolate volatile organic compounds from various matrices such as water, sand, clay, and sludge. By use of the technique, benzene, toluene, ethyl-benzene, and xylene isomers (commonly known as BTEX), and volatile chlorinated compounds can be efficiently isolated from various matrices with good precision and low limits of detection. This study has found that the sensitivity of the method can be greatly improved by the addition of salt to water samples, water to soil samples, or by heating. Headspace SPME can also be used to sample semi-volatile compounds, such as PAHs, from complex matrices.     

ACF-SPME检测海洋水体中的多环芳烃

使用新型活性炭纤维(ACF)作为固相微萃取(SPME)技术的萃取纤维,检测了海水中的多环芳烃。得到ACF-SPME萃取多环芳烃的最优条件为:在搅拌条件下,盐浓度10%,pH3,温度60℃水浴中直接萃取40min。并确定16种多环芳烃的RSD(n=5)为1.8%～10%、线性范围为0.1～500μg/L、检出限为0.1～100μg/L。对东海近海海水进行了分析,结果表明海水中PAHs浓度在检测限以下,同时进行加标回收实验,得到16种多环芳烃的回收率在80%～128%。     

A magnetic multifunctional dendrimeric coating on a steel fiber for solid phase microextraction of chlorophenols

Microchimica Acta - A polyamidoamine dendrimer was synthesized, placed on magnetite nanoparticles, and the resulting material was then employed as a fiber coating for use in solid phase...     

Novel cationic surfactant ion pair based solid phase microextraction fiber for nano-level analysis of BTEX

Ion pair of cationic surfactant (cetytrimethylammonium bromide) and tungestosilicic acid incorporated in PVC matrix, was used for coating a piece of copper wire as a new high sensitive SPME fiber in extraction and determination of BTEX compounds from the headspace of water samples prior to GC/FID analysis. Under optimum extraction conditions, limits of detection for benzene, toluene, ethylbenzene, p-xylene, m-xylene and o-xylene were found to be 1.18, 5.61, 0.87, 0.29, 0.22 and 0.33 ng L(-1) respectively. Low detection limits, wide linear dynamic ranges, good reproducibility (RSD% 1.48-4.27), high fiber capacity and high mechanical durability are some of the most important advantages of the new fiber.     

聚苯胺/二氧化钛纳米管固相微萃取纤维的组装及应用

以钛丝表面原位阳极氧化生成的二氧化钛纳米管为基体,通过电聚合苯胺组装得到新型聚苯胺包覆二氧化钛复合纳米管阵列固相微萃取纤维。实验讨论了无机酸介质、苯胺浓度和氧化电压对电聚合苯胺的影响,经过对纤维表面形貌和元素成分的分析,得到最佳的纤维涂层条件:电解液组成为1 mol/L的H₂SO₄-0.5 mol/L的苯胺,聚合电压10 V,氧化时间60 min。采用所制备的纤维与高效液相色谱联用萃取水样中的紫外线吸收剂并优化萃取条件,固相微萃取条件如下:萃取时间40 min,解吸时间4 min,萃取温度40℃,搅拌速率600 r/min,样品溶液中不加NaCl。同时对环境水样中的目标物分析测定,并做加标试验,目标分析物的平均回收率为78.2%～118%,相对标准偏差为4.4%～8.9%。该方法简便、灵敏、准确,适用于环境水样中紫外线吸收剂的快速测定。     

Application of solid phase microextraction for the determination of soil fumigants in water and soil samples

The potential of solid phase microextraction (SPME) for the determination of the soil fumigants 1,3-dichloropropene (1,3-DCP) and methyl isothiocyanate (MITC) in environmental samples such as soil and water samples has been investigated. Direct immersion SPME followed by GC/ECD/NPD analysis allowed the rapid determination of the two fumigants in water samples, with very little sample manipulation, giving an LOD of 0.5 microg L(-1). Precision, calculated as relative standard deviation (RSD) for six replicates at three concentration levels, was found to be lower than 20% at the concentration levels tested. For the analysis of soil samples, headspace (HS)-SPME combined with GC/ECD/NPD analysis has been applied. Quantification using matrix-matched calibration curves allowed determination of both analytes (MITC and 1-3-DCP) with a LOD of 0.1 microg kg(-1) (RSD < 10%) for the two concentration levels assayed (0.02 and 0.2 mg kg(-1)). The HS-SPME procedure developed in this paper was applied to soil samples from experimental green house plots treated with metham-Na, a soil disinfestation agent that decomposes in soil to MITC. The absence of sample manipulation as well as the low solvent consumption in SPME methodology are among the main advantages of this analytical approach.     

Monolithic molecular imprinted polymer fiber for recognition and solid phase microextraction of ephedrine and pseudoephedrine in biological samples prior to capillary electrophoresis analysis

A novel capillary electrophoresis (CE) method coupled with monolithic molecular imprinted polymer (MIP) fiber based solid phase microextraction (SPME) was developed for selective and sensitive determination of ephedrine (E) and pseudoephedrine (PE). With in situ polymerization in a silica capillary mold and E as template, the MIP fibers could be produced in batch reproducibly and each fiber was available for 50 extraction cycles without significant decrease in extraction ability. Using the MIP fiber under optimized extraction conditions, CE detection limits of E and PE were greatly lowered from 0.20 to 0.00096 μg/mL and 0.12 to 0.0011 μg/mL, respectively. Analysis of urine and serum samples by the MIP-SPME-CE method was also performed, with results indicating that E and PE could be selectively extracted. The recoveries and relative standard deviations (RSDs) for sample analysis were found in the range of 91–104% and 3.8–9.1%, respectively.     

An aniline-based fiber coating for solid phase microextraction of polycyclic aromatic hydrocarbons from water followed by gas chromatography-mass spectrometry

A fiber coating from polyaniline (PANI) was electrochemically prepared and employed for solid phase microextraction (SPME) of some polycyclic aromatic hydrocarbons (PAHs) from water samples. The PANI film was directly electrodeposited on the platinum wire surface in sulfuric acid solution using cyclic voltammetry (CV) technique. The applicability of this coating was assessed employing a laboratory-made SPME device and gas chromatography with mass spectrometry (GC-MS) for the extraction of some PAHs from the headspace of aqueous samples. Application of wider potential range in CV led to a PANI with more stability against the temperature. The homogeneity and the porous surface structure of the film were examined by the scanning electron microscopy (SEM). The study revealed that this polymer is a suitable SPME fiber coating for extracting the selected PAHs. Important parameters influencing the extraction process were optimized and an extraction time of 40 min at 40 degrees C gave maximum peak area, when the aqueous sample was added with NaCl (20%, w/v). The synthesis of the PANI can be carried out conveniently and in a reproducible manner while it is rather inexpensive and stable against most of organic solvents. The film thickness of PANI can be precisely controlled by the number of CV cycles. The resulting thickness was roughly 20 microm after 20 cycles. At the optimum conditions, the relative standard deviation (RSD) for a double distilled water spiked with selected PAHs at ppb level were 8.80-16.8% (n = 3) and detection limits for the studied compounds were between 0.1-6 pg mL(-1). The performance of PANI was, also, compared with a commercial solid coated-based SPME fiber, carbowax/divinylbenzene (CW/DVB), under similar experimental conditions.     

Analysis of anatoxin-a in biological samples using liquid chromatography with fluorescence detection after solid phase extraction and solid phase microextraction

Anatoxin-a is a naturally occurring, potent neurotoxin produced by some species of cyanobacteria in freshwaters. This toxin, which is a potential health hazard, especially to animals, has been determined in different biological matrices such as several cyanobacterial cultures and water samples and carps and mussels tissue using a sensitive High Performance Liquid Chromatography with Fluorescence detection method. Sonication was the technique selected for the extraction of intracellular anatoxin-a and solid phase extraction using weak cation exchange was used for the concentration and purification of the samples. 4-Fluoro-7-nitro-2,1,3-benzoxadiazole (NBD-F) was used to convert anatoxin into a highly fluorescent derivative. Recovery experiments were performed for each type of matrix used in this work, and adequate values were obtained (71-87%). Limits of detection for anatoxin-a were estimated to be in the ng/L and ng/g level for water and cyanobacterial samples, respectively. The results obtained were also compared with those obtained after using solid phase microextraction, as an alternative for the extraction and purification of the samples. Advantages and disadvantages regarding to the efficiency for impurities removal, simplicity and rapidity and the potential for concentration enhancement of using both methodologies have been also discussed.