Electrical conductivity in strontium titanate

The electrical conductivity of polycrystalline SrTiO₃ was determined for the oxygen partial pressure range of 10° to 10^?22 atm and temperature range of 800 to 1050°C. The data were found to be proportional to the $\text{?1}\text{6}\text{th}$ power of the oxygen partial pressure for the oxygen pressure range 10^?15–10^?22 atm, proportional to for the oxygen pressure range 10^?8–10^?15 atm, and proportional to for the oxygen pressure range 10⁰–10^?3 atm. These data are consistent with the presence of very small amounts of acceptor impurities in SrTiO₃.     

Thermodynamic restrictions on mechanosynthesis of strontium titanate

Chemical potential phase stability diagrams were calculated from relevant thermodynamic properties and used to predict the thermodynamic driving force under prospective conditions of room temperature mechanosynthesis. One analysed the dependence of chemical potential diagrams on temperature and partial pressure of evolving gases such as oxygen or carbon dioxide, as expected on using strontium peroxide or strontium carbonate as precursor reactants for the alkali earth component. Thermodynamic calculations were also obtained for changes in titania precursor reactants, including thermodynamic predictions for reactivity of strontium carbonate with amorphous titania. Experimental evidence showed that strontium titanate can be obtained by mechanosynthesis of strontium carbonate+anatase mixtures, due to previous amorphization under high energy milling. Ability to perform mechanosynthesis with less energetic milling depends on the suitable choice of alternative precursor reactants, which meet the thermodynamic requirements without previous amorphization; this was demonstrated by mechanosynthesis from anatase+strontium peroxide mixtures.     

Promising membrane materials based on strontium titanate

Electroconductivity of SrTi_1?x Fe _x O_3?δ(x = 0–0.5) specimens was studied by four-probe method. An opportunity was studied to produce hydrogen by high-temperature electrochemical conversion using SrTi_0.5Fe_0.5O_3?δ as the membrane material of the best conductivity. The effective ambipolar conductivity values calculated for SrTi_0.5Fe_0.5O_3?δ from the leakage experiment were found different from the ambipolar conductivity values calculated by the four-probe data processing because ambipolar conductivity corresponds to bulk transfer of complex oxide particles, taking no surface phenomena into account.     

Synthesis of single-crystalline perovskite nanorods composed of barium titanate and strontium titanate

We report the solution-based synthesis of single-crystalline nanorods composed of barium titanate (BaTiO3) and strontium titanate (SrTiO3), which yields well-isolated nanorods with diameters ranging from 5 to 60 nm and lengths reaching up to >10 mum. Electron microscopy and diffraction measurements show that these nanorods are composed of single-crystalline cubic perovskite BaTiO3 and SrTiO3 with a principal axis of the unit cell preferentially aligned along the wire length. These BaTiO3 and SrTiO3 nanorods should provide promising materials for fundamental investigations on nanoscale ferroelectricity, piezoelectricity, and paraelectricity.     

Electrical conductivity in strontium titanate with nonideal cationic ratio

The electrical conductivity of polycrystalline strontium titanate with ($\text{Sr}\text{Ti}\text{= 0.996, 0.99,}\text{and}\text{0.98}$ was determined for the oxygen partial pressure range of 10⁰ to 10^?22 atm and the temperature range of 850–1050°C. These data were found to be similar to that obtained for the sample with ideal cationic ratio. The observed data were proportional to the $\text{?}\text{1}\text{6}$ power of oxygen partial pressure for P_O2 < 10^?15atm, proportional to for the pressure range 10^?8–10^?15 atm, and proportional to for P_O2 > 10^?4atm. The deviation from the ideal Sr-to-Ti ratio was found to be accommodated by neutral vacancy pairs, (V″_Sr V″₀. The results indicate that the single-phase field of strontium titanate extends beyond 50.505 mole% TiO₂ at elevated temperatures.     

Direct large-scale synthesis of perovskite barium strontium titanate nano-particles from solutions

This paper reports a wet chemical synthesis technique for large-scale fabrication of perovskite barium strontium titanate nano-particles near room temperature and under ambient pressure. The process employs titanium alkoxide and alkali earth hydroxides as starting materials and involves very simple operation steps. Particle size and crystallinity of the particles are controllable by changing the processing parameters. Observations by X-ray diffraction, scanning electron microscopy and transmission electron microscopy TEM indicate that the particles are well-crystallized, chemically stoichiometric and ∼50 nm in diameter. The nanoparticles can be sintered into ceramics at 1150 °C and show typical ferroelectric hysteresis loops.     

Hydrothermally assisted complex polymerization method for barium strontium titanate powder synthesis

Barium strontium titanate was obtained by hydrothermal treatment of barium strontium titanate citric precursor solution, previously prepared by complex polymerization method. The thermally induced phase evolution was followed at various temperatures up to 800 °C using thermogravimetric and differential thermal analysis, X-ray diffraction analysis, and Raman spectroscopy. Microstructural characterization of barium strontium titanate powders was performed by scanning and transmission electron microscopy. The proposed synthesis route has been proven as a better and faster method for barium strontium titanate powder preparation as compared to the conventional complex polymerization route. The method was found efficient for production of low agglomerated, fine, nanosized barium strontium titanate powder with well defined stoichiometry, and sub-micron particle size. The results of structural and microstructural characterization showed the complete crystallization of carbonate-free barium strontium titanate powder at 700 °C with an average size of crystallites below 50 nm.     

Determination of impurities in strontium titanate ceramics by inductively coupled plasma mass spectrometry

The determination of impurities in SrTiO₃ by ICPMS was investigated. The sample was decomposed with hydrochloric and hydrofluoric acids in a PTFE pressure vessel. The internal standard method using Au was selected to eliminate an ion count suppression by the Sr and Ti matrix. Impurities at sub g/ml level in SrTiO₃ were determined. The detection limits were in the range of 0.008 to 0.01 g/g.     

锆钛酸镧铅结构象和缺陷

锆钛酸镧铅(简称 PLZT)是一种十分重要的铁电材料.利用 PLZT 透明陶瓷的场致相变,还有可能在图象存贮和显示中得到应用.目前,在利用 La/Zr/Ti 比为7.9/70/30或8/65/35的 PLZT 透明陶瓷制作平面显示器、散射光开关和电光图象存贮器等方面开展了不少工作.PLZT 透明陶瓷的基本组成是锆钛酸铅掺 La 改性,形成(Pb,La)(Zr,Tj)O_3四元系固溶体.化学式倾向于:Pb_(1-x),La_x(Zr_(1-y),Ti_y)_(1-x/4)O_3.其中,La 的浓度 x 可在2～30％之间改变,而 Zr 与 Ti 的相互比例可连续变化.为了提高 PLZT 性能,人们往往通过改变这一比例加以实现.然而,我们的计算结果指出,这一比例的改变将使晶格能发生变化.我们用高分辨电子显微镜在晶格水平上对配比为8/65/35和7.9/70/30的 PLZT 进行了观察,发现配方7.9/70/30有更多的缺陷.计算表明,这可能是由于7.9/70/30的晶格能比8/65/35相对较低造成的.     

Microwave synthesis of barium titanate,strontium zirconate,and sodium indium tungstate

The results of microwave (at a frequency of 2.45 GHz) synthesis of BaTiO₃, SrZrO₃, and NaIn(WO₄)₂ are compared with those of the common solid-phase synthesis.     

Effect of biphase on dielectric properties of Bi-doped lead strontium titanate thin films

Pb_0.4Sr_0.6TiO₃ (PST) thin films doped with various concentration of Bi were prepared by a sol-gel method. The phase status, surface morphology and dielectric properties of these thin films were measured by X-ray diffraction (XRD), scanning electron microscopy (SEM) and impedance analyzer, respectively. Results showed that the thin films with the maximum dielectric constant and minimum dielectric loss were obtained for x=0.15. For x<0.15, only pure PST perovskite phase were in the thin films. For 0.2<x<0.4, the PST/Bi₂Ti₂O₇ biphase were obtained. The thin films with pure Bi₂Ti₂O₇ pyrochlore phase were obtained for x=0.67. The biphase thin films had high tunability and high figure of merit (FOM). The FOM of PST/Bi₂Ti₂O₇ biphase thin film was about 6 times higher than that thin films formed with pure perovskite phase or pure pyrochlore phase.     

Nanofibers of barium strontium titanate (BST) by sol-gel processing and electrospinning

This paper describes the fabrication of barium strontium titanate (Ba0.6Sr0.4TiO3 or BST) nanofibers by electrospinning method using a solution that contained poly(vinylpyrrolidone) and a sol-gel solution of BST. The as-spun and calcined BST/PVP composite nanofibers were characterized by TG-DTA, X-ray diffraction, FT-IR, SEM and TEM, respectively. After calcination of the as-spun BST/PVP composite nanofibers at above 700 degrees C in air for 2 h, BST nanofibers of 188+/-25 nm in diameter having well-developed cubic-perovskite structure were successfully obtained. The crystal structure and morphology of the nanofibers were influenced by the calcination temperature. Calcination at below 700 degrees C resulted in amorphous phase whereas BST with second phase such as barium titanate were formed at above 700 degrees C. Diameters of the nanofibers decreased from 208+/-35 to 161+/-18 nm with increasing calcination temperature between 600 and 800 degrees C.     

Point defects and lock-in faults in columnar phases

We show the existence of point defects connected by strings in columnar phases. The most interesting consequence is the increase, by several orders of magnitudes, of the bend elastic modulus as compared to values for nematics.     

Systematic microstructural development with thermal diffusivity behaviour from nanometric to micronic grains of strontium titanate

Journal of Thermal Analysis and Calorimetry - Strontium titanate is a promising candidate for applications in thermoelectric, thermal management applications, and modern electronic devices because...     

Point and ring defects in nematics under capillary confinement

The textures exhibited by nematic liquid crystals confined to cylindrical capillaries under homeotropic anchoring have been studied for nearly thirty years. One of the reasons behind this maintained interest is that the processing of many high-performance fibers including carbon fibers and spider silks involves these textures. Three of these textures, the planar radial with line defect, the planar polar with two line defects (PPLD), and the escape radial (ER), are relatively well understood. A third one, the escape radial with point defects presents, however, some unresolved issues and recent studies have questioned the real nature and dimensionality of the defects involved in this texture. It seems that the defects are not in the form of points but rather in the form of closed lines or rings. This paper presents a detailed study on the connection between point and ring defects in a cylindrical cavity using three-dimensional simulations based on the continuum Landau-de Gennes theory. The results show that true point defects cannot exist in cylindrical cavities and that the merging of two ringlike defects may lead to two qualitatively different stable textures, namely, the ER and PPLD textures. The various results are in qualitative agreement with recent molecular dynamic studies and with theoretical predictions based on experimental observations. The predictions provide new insights on the structural connections between synthetic and biological superfibers.     

Development of prototype titanate ion-exchange loaded-membranes for strontium, cesium and actinide decontamination from aqueous media

We have successfully incorporated high surface area particles of titanate ion-exchange materials (monosodium titanate and crystalline silicotitanate) into porous and inert support membrane fibrils. The resulting membrane sheets were used to evaluate the removal of surrogate radioactive materials for cesium-137 and strontium-90 from high caustic nuclear waste simulants. The membrane supports met the nominal requirement for non-chemical interaction with the embedded ion-exchange materials and were porous enough to allow sufficient liquid flow. Most of the stamped out 47-mm size titanium impregnated ion-exchange membrane discs removed more than 96% of dissolved cesium-133 and strontium-88 from caustic nuclear waste salt simulants.     

Effect of lattice defects on the annealing of γ-irradiation damage in strontium bromate

The role of lattice defects introduced by crushing and doping on the annealing of chemical radiation damage in strontium bromate has been investigated. Crushing of irradiated crystals produces direct recovery and also accelerates the subsequent thermal annealing. The initial damage and the susceptibility to thermal annealing are greater in the doped crystals than that in the untreated samples.     

Selected-area sol-gel deposition of barium strontium titanate thin films on thermally oxidized silicon through mediation of self-assembled monolayers

Self-assembled monolayers (SAMs) of octadecyltrichlorosilane (OTS) and mercapto ethanol were used to modify the surface functionality of platinum/titanium or platinum/tantalum bilayer patterns on thermally oxidized silicon wafers. The attachment of OTS to the exposed oxide region made it hydrophobic, while the anchoring of mercapto ethanol to the bilayer pattern turned it hydrophilic. This patterned hydrophobicity and hydrophilicity was exploited to preferentially deposit barium strontium titanate (BST) thin films on the patterned bilayers from an aqueous sol-gel solution. The combination of the SAMs and the sol-gel film formation method allowed direct patterned deposition of BST thin films, which could be useful for on-chip electronic applications. Wet oxygen annealing at 50 °C was sufficient to stabilize the deposited sol-gel coating without adversely affecting the functionality of the OTS, thus permitting multiple dip-coatings to obtain patterned films of a desired thickness. Heat treatment at 750 °C allowed densification and conversion of the sol-gel coatings to perovskite BST films.     

Improvement of the electro-optical properties of nematic liquid crystals doped with strontium titanate nanoparticles at various doping concentrations

ABSTRACT

In this study, we doped homogenous aligned nematic liquid crystal (NLC) systems with strontium titanate (SrTiO₃) nanoparticles (NPs), and investigated the impact of doping concentration on the NLC’s electro-optical (EO) properties. SrTiO₃ NP-doped NLC cells maintained a high optical transmittance of 77.51% to 78.41% compared to pure NLC cells (78.09%). At a 0.1 wt.% SrTiO₃ NP doping concentration, twisted-nematic (TN)-LC cells exhibited enhanced EO performance, with a reduced threshold voltage from 1.70V to 1.61V and a shorter response time from 17.03 ms to 10.66 ms without optical defects and degradations. We also observed an improvement in thermal endurance for doping concentrations of 0.05 and 0.1 wt.%.