A novel chemically modified carbon paste electrode based on a new mercury(II) complex for selective potentiometric determination of bromide ion

A new modified carbon paste electrode based on a recently synthesized mercury (II) complex of a pyridine containing proton transfer compound as a suitable carrier for Br⁻ ion is described. The electrode has a linear dynamic range between 3.00×10⁻² and 1.0×10⁻⁵ M with a near-Nernastian slope of 61.0±0.9 mV per decade and a detection limit of 4.0×10⁻⁶ M (0.32 ppm). The potentiometric response is independent of the pH of the solution in the pH range 4.0–8.3. The electrode possesses the advantages of low resistance, fast response and good over a variety of other anions. It was applied as an indicator electrode in potentiometric titration of bromide ions and for the recovery of Br⁻ from tap water.     

Stripping voltammetric determination of silymarin in formulations and human blood utilizing bare and modified carbon paste electrodes

Silymarin is one of the most powerful natural substances that have the ability to protect and rebuild the liver cells damaged by alcohol and other toxic substances. Silymarin showed two irreversible anodic peaks in buffered solutions (pH 2.5-8.0) at either the bare carbon paste electrode or the montmorillonite-Ca modified carbon paste one. These two peaks have been attributed to oxidation of the two phenolic OH groups at positions C-20 and C-7 of silymarin molecule. A square-wave adsorptive anodic stripping voltammetry method was optimized for determination of silymarin utilizing the bare and the modified carbon paste electrodes. The method was fully validated and successfully applied for the determination of silymarin in commercial formulations and human serum without prior extraction utilizing both carbon paste electrodes. Limits of quantitation of 1 × 10⁻⁷ and 7 × 10⁻⁹ mol L⁻¹ silymarin have been achieved in bulk form or in formulations while 2 × 10⁻⁷ and 8 × 10⁻⁹ mol L⁻¹ silymarin were achieved in spiked human serum utilizing the bare carbon paste electrode and the modified one, respectively. The two electrodes exhibited excellent selectivity towards silymarin even in the presence of 10²to 10³-fold excess of its co-formulated drugs, common excipients, and common metal ions. The pharmacokinetic parameters of silymarin in plasma of healthy human volunteers were estimated following the administration of a single oral dose of 120 mg silymarin utilizing the modified carbon paste electrode. The estimated pharmacokinetic parameters were favorably compared with those reported in literature.     

A single-wall carbon nanotubes modified edge plane pyrolytic graphite sensor for determination of methylprednisolone in biological fluids

An electrochemical protocol based on reduction is developed to determine methylprednisolone using single-wall carbon nanotubes (SWNTs) modified edge plane pyrolytic graphite electrode (EPPGE). To obtain a good sensitivity, instrumental variables were studied using Square Wave Voltammetry (SWV). The voltammetric results indicate that SWNTs modified EPPGE remarkably enhances the reduction of methylprednisolone which leads to considerable improvement of peak current with shift of peak potential to less negative values. The voltammetric current showed a linear response for methylprednisolone concentration in the range 5-500 nM with a sensitivity of 98 nA nM⁻¹. The limit of detection was estimated to be 4.5 × 10⁻⁹ M. The developed method is used for the determination of methylprednisolone in pharmaceutical dosages and human blood plasma samples of patients undergoing treatment with methylprednisolone. The major metabolites present in blood plasma did not interfere with the present investigation as they did not exhibit reduction peak in the experimental range used. A comparison of results with high performance liquid chromatography (HPLC) indicates a good agreement.     

修饰的多壁碳纳米管糊电极用于生物与制药样品中苄丙酮香豆素电催化氧化和测定

采用一种简单灵敏的方法开发了在多壁碳纳米管修饰的ZnCrFeO4糊电极(MWCNTs/ZnCrFeO4/CPE)表面测定苄丙酮香豆素的新型传感器.运用循环伏安法、差示脉冲伏安法、计时电流法和电化学阻抗谱考察了该化学修饰电极上苄丙酮香豆素的电化学性能.结果表明,MWCNTs/ZnCrFeO4/CPE电极对苄丙酮香豆素氧化表现出较高的电催化活性,在pH=4时,产生峰值氧化电流约0.97 vs Ag/AgCl参比电极.当苄丙酮香豆素浓度在0.02-920.0 μmol/L范围内,该峰电流与其呈线性关系,检测极限(3σ)为0.003 μmol/L.另外,运用差示脉冲伏安法测定了MWCNTs/ZnCrFeO/CPE电极上苄丙酮香豆素的催化反应速率常数和扩散系数.     

Voltammetric determination of piroxicam in micellar media by using conventional and surfactant chemically modified carbon paste electrodes

A method for piroxicam determination based on adsorptive stripping voltammetric techniques, using conventional and chemically modified carbon paste electrodes in micellar media, is described. The employed surfactants were sodium dodecyl sulfate (SDS), Triton X-100, Triton X-405, Tween 80 and Brij 30. However, the purpose of this paper is, at present, to research the use of surfactants as carbon paste modifier because one of the mechanisms of hydrophobic drugs ad-accumulation on the carbon paste electrode is based on the chemical affinity. Besides, because of the water piroxicam insolubility, a special aqueous medium, such as a surfactant solution above its c.m.c. was used, this micellar media being very advantageous in relation to the use of organic or aqueous-organic media, in order to dissolve the studied drug and to remove the problems derived from the organic solvents use. In addition, a piroxicam ad-accumulation increase, on surfactant modified carbon paste electrode, with the surfactant mass incorporated into the electrode, was observed.     

ZrO2-Graphene-Chitosan nanocomposite modified carbon paste sensor for sensitive and selective determination of dopamine

A sensitive and stable electrochemical sensor was developed by modification of carbon paste electrode with ZrO₂/graphene/chitosan nanocomposite. The modified sensor served as a potential electrocatalytic platform for dopamine. Electrochemical impedance spectroscopy studies indicated reduction of charge transfer resistance at the modified electrode surface thereby facilitating the electron transfer process which resulted in higher current response to dopamine. The electrochemical behavior of dopamine at the modified electrode was studied using cyclic and square wave voltammetry. The maximum current response for the electro-oxidation of dopamine was observed at pH 7.4 and the process was realized to be diffusion controlled. The modified sensor demonstrated linearity in the range 1000–5000 nM, with high sensitivity (22 nA/nM), detection limit of 11.3 nM and selectivity for dopamine in the presence of ascorbic and uric acid which are found to co-exist with dopamine in physiological media. The method was employed for quantification of dopamine in a pharmaceutical formulation.     

Simultaneous anodic stripping voltammetric determination of lead and cadmium with a carbon paste electrode modified by tributyl phosphate

A novel chemiluminescence (CL) flow sensor has been developed for the monitoring of iron(III). The analytical reagents involved in the CL reaction, including luminol and hexacyanoferrate(II) were both immobilized on an anion-exchange resin column. When sodium sulfate solution was passed through the column, these two reagents were eluted from the resins and then mixed with an iron(III) stream. By the fast reaction between iron(III) and hexacyanoferrate(II), the complex Prussian Blue was generated, which could catalyse the luminol oxidation by dissolved oxygen in alkaline aqueous solution to produce CL. The CL emission intensity was correlated with the standard iron(III) concentration in the range 0.01-Smgl^–1, and the detection limit was 7 × 10^–3mgl^–1 iron(III). A complete analysis, including sampling and washing, could be performed in l min with a relative standard deviation of less than 5%. The sensor was stable for over 200 times and has been applied successfully to the determination of iron in blood samples.     

Potentiometric stripping analysis of methyl and ethyl parathion employing carbon nanoparticles and halloysite nanoclay modified carbon paste electrode

Carbon nanoparticles (CNPs) and halloysite nanoclay (HNC) modified carbon paste electrode (HNC–CNP–CPE) was developed for the determination of methyl parathion (MP) and ethyl parathion (EP). The electrochemical behavior of these molecules was investigated employing cyclic voltammetry (CV), chronocoulometry (CC), electrochemical impedance spectroscopy (EIS) and potentiometric stripping analysis (PSA). After optimization of analytical conditions employing this electrode at pH 5.0 in acetate buffer (0.1 M), the peak currents were found to vary linearly with its concentration in the range of 1.55 × 10⁻⁹ to 3.67 × 10⁻⁶ M and 1.21 × 10⁻⁹ to 4.92 × 10⁻⁶ M for MP and EP, respectively. The detection limits (S/N = 3) of 4.70 × 10⁻¹⁰ M and 3.67 × 10⁻¹⁰ M were obtained for MP and EP, respectively, using PSA. The prepared modified electrode showed several advantages such as simple preparation method, high sensitivity, very low detection limits and excellent reproducibility. The proposed method was employed for the determination of MP and EP in fruits, vegetables, water and soil samples.     

Determination of captopril in patient human urine using ferrocenemonocarboxylic acid modified carbon nanotubes paste electrode

<正>In this work,we describe a new strategy for the electrochemical determination of captopril(CA) using ferrocenemonocarboxylic acid as a mediator and multiwall carbon nanotubes as sensors in aqueous solution at pH 7.0.The diffusion coefficient(D),and the kinetic parameters such as electron transfer coefficient(α).and heterogeneous rate constant(k_h),for CA were also determined using electrochemical approaches.Under the optimized conditions,the electrocatalytic oxidation peak current of captopril showed two linear dynamic ranges with a detection limit of 0.3×10~(-6) mol L~(-1) captopril.The linear calibration range was 0.8×10~(-6) to 65×10~(-6) mol L~(-1) using cyclic voltammetry.Finally,this modified electrode was also examined as a selective,simple and precise new electrochemical sensor for the determination of captopril in real samples such as drug and patient human urine.     

邻苯三酚红多壁碳纳米管糊电极为传感器分析制药和生物样品中异丙基肾上腺素

异丙基肾上腺素(ISPR)是一种重要的邻苯二酚胺类药物,广泛用于治疗心脏疾病.然而,过量服用该药对人体非常危险.本文采用邻苯三酚红修饰多壁碳纳米管糊电极(PGRMMWCNTPE)制备了一种新型传感器,用于高灵敏度检测水溶液中的ISPR.采用计时电流法、循环伏安法和方波伏安法考察了PGRMMWCNTPE电极电催化氧化ISPR性能.通过伏安数据计算了ISPR氧化的催化反应速率常数、电子传递系数和扩散系数.在ISPR浓度0.8–570μmol/L范围内建立了线性标准曲线,检测限为0.47μmol/L ISPR.将该传感器用于尿液和药物样品中ISPR检测得到满意结果.     

对硫磷在聚乙烯吡咯烷酮修饰碳糊电极上的电化学行为及其分析研究

研究了对硫磷在聚乙烯吡咯烷酮(PVP)修饰碳糊电极(CPE)上的电化学行为,发现PVP能显著提高对硫磷的氧化还原峰电流.据此建立了一种直接测定对硫磷的电分析方法.对硫磷氧化峰电流与其浓度在2.5×10-8～1.0×10-6mol/L及1.0×10-6～1.0 × 10-5mol/L 范围内呈良好的线性关系,开路富集5 min后,检出限为7.5×10-9mol/L.在1.0×10-5mol/L的对硫磷试液中连续测定10次,其RSD为2.8%.用此方法测定了蔬菜中的对硫磷.     

New approach to the simultaneous analysis of catecholamines and tyrosines in biological fluids

New high-performance liquid chromatographic (HPLC) methods with amperometric-CoulArray detection were developed for simultaneous analyses of norepinephrine, epinephrine, L-DOPA, dopamine, 3-nitrotyrosine, m-, o-, and p-tyrosines. Overall, detection limit was in the low pmol range with amperometry, and in the low fmol range for the CoulArray method. Linear (r2 = 0.99) detector performances were observed in the ranges of 2-200 pmol with amperometry, and 0.2-20 pmol for the CoulArray method. Analytical precision values were better than 80 and 95% for HPLC-amperometry and HPLC-CoulArray method, respectively. These methods offer sensitivity, specificity, minimal sample requirement, and especially the HPLC-CoulArray method allows simultaneous assessment of various similar biomolecules.     

A novel sensor based on multi-walled carbon nanotubes and boron-doped double-layer molecularly imprinted membrane for the analysis of SCZ in pharmaceutical and biological samples

ABSTRACT

A molecularly imprinted electrochemical sensor for the rapid detection of the anti-parasitic drug Secnidazole (SCZ) is reported. In this work, the build electrochemical sensor was based on a carbon paste electrode (CPE) modified with multi-wall carbon nanotubes (MWCNTs) and boron-embedded duplex molecularly imprinted composite membranes (B-DMICMs), that significantly increased the efficiency of the sensor for the detection of template molecule SCZ. Density functional theory (DFT) was employed to study the interactions between the template and monomers to select appropriate functional monomers for rational design of the B-DMICMs.The optimal experimental conditions were optimised for the factors affecting the performance of the sensor. Under the optimal conditions, the reduction peak currents of SCZ by differential pulse voltammetry increased linearly with SCZ concentration in the range from 3.0 × 10^?4 to 1.0 × 1.0^?6 mol L^?1 and 1.0 × 1.0^?6 to 1.91 × 10^?8 mol L^?1 with a detection limit of 1.72 × 10^?8 mol L^?1 for secnidazole, which is significantly lower than those in the currently used methods and in previous reports. This method offers low cost, sensitive and effective determination of SCZ and can potentially be used for detection of SCZ in pharmaceutical and biological samples with good precision and accuracy.     

Glucose sensor based on redox-cycling between selectively modified and unmodified combs of carbon interdigitated array nanoelectrodes

We present a novel electrochemical glucose sensor employing an interdigitated array (IDA) of 1:1 aspect ratio carbon nanoelectrodes for the electrochemical-enzymatic redox cycling of redox species (ferricyanide/ferrocyanide) between glucose oxidase (GOx) and the two comb-shaped nanoelectrodes of the IDA. The carbon nanoelectrodes were fabricated using a simple, cost-effective, reproducible microfabrication technology known as the carbon-microelectromechanical-systems (C-MEMS) process. One comb (comb 1) of the IDA was selectively modified with GOx via the electrochemical reduction of an aryl diazonium salt, while the other comb (comb 2) remained unmodified; this facilitates electrochemically more active surface of comb 2, resulting in sensitive glucose detection. Ferricyanide is reduced to ferrocyanide by the GOx in the presence of glucose, and ferrocyanide diffuses to both combs of the IDA where it is oxidized. The limited electrochemical current collection at the surface-modified comb 1 is counterbalanced by the efficient redox cycling between the enzyme sites at comb 1 and the bare carbon surface of comb 2. Reducing the electrode-to-electrode gap between the two combs (gap = 1.9 μm) increases the diffusion flux of redox species at comb 2 hence, enhanced the sensitivity and limit of detection of the glucose sensor by ∼2.3 and ∼295 times, respectively at comb 2 compared to comb 1. The developed IDA-based glucose sensor demonstrated good amperometric response to glucose, affording two linear ranges from 0.001 to 1 mM and from 1 to 10 mM, with limits of detection of 0.4 and 61 μM and sensitivities of 823.2 and 70.0 μA mM⁻¹ cm⁻², respectively.     

Ag ion irradiated based sensor for the electrochemical determination of epinephrine and 5-hydroxytryptamine in human biological fluids

A promising and highly sensitive voltammetric method has been developed for the first time for the determination of epinephrine (EP) and 5-hydroxytryptamine (5-HT) using 120 MeV Ag ion irradiated multi-walled carbon nano tube (MWCNT) based sensor. The MWCNT were irradiated at various fluences of 1e12, 3e12 and 1e13 ions cm⁻² using palletron accelerator. The simultaneous determination of EP and 5-HT has been carried out in phosphate buffer solution of pH 7.20 using square wave voltammetry and cyclic voltammetry. Experimental results suggested that irradiation of MWCNT by Ag ions enhanced the electrocatalytic activity due to increase in effective surface area and insertion of Ag ions, leading to a remarkable enhancement in peak currents and shift of peak potentials to less positive values as compared to the unirradiated MWCNT (pristine). The developed sensor exhibited a linear relationship between peak current and concentration of EP and 5-HT in the range 0.1–105 μM with detection limit (3σ/b) of 2 nM and 0.75 nM, respectively. The practical utility of irradiation based MWCNT sensor has been demonstrated for the determination of EP and 5-HT in human urine and blood samples.     

A novel planar miniaturized potentiometric sensor for flow injection analysis of nitrates in wastewaters, fertilizers and pharmaceuticals

A novel all-solid-state miniaturized nitrate sensor is developed, characterized and used for flow injection analysis (FIA) of nitrates in various samples. The sensor incorporates silver bis(bathophenanthroline) nitrate [Ag(bath)₂NO₃] as an electroactive material in a plasticized PVC membrane. The sensing membrane (3 mm × 5 mm) is immobilized on a wafer polyimide microchip (size 13.5 mm × 3.5 mm) to offer a planar miniaturized design easily used in a single channel wall-jet flow injection system. Under hydrodynamic mode of operation (FIA) the sensor displays fast response, high sensitivity, long term stability and good selectivity for NO₃⁻ in the presence of many common associated anions. The calibration slope is 55.1 ± 0.1 mV decade⁻¹ over the concentration range 1.0 × 10⁻¹ to 1.0 × 10⁻⁶ mol L⁻¹, the lower detection limit is 0.05 μg mL⁻¹, the working pH is 2-9,and the output is 70-90 samples h⁻¹. Validation of the assay method reveals good performance characteristics and suggests application for routine determination of NO₃⁻ in industrial wastewaters, fertilizers and pharmaceuticals. The results agree fairly well with data obtained by the standard spectrophotometric methods.     

Fabrication of chemically modified carbon paste electrode based on functionalized biopolymer for potentiometric determination of Al (III) ion in real water and pharmaceutical samples

Carbon paste electrode modified with Carboxymethyl chitosan-graft-poly(1-cyanoethanoyl-4-acryloyl-thiosemcarbazide)copolymers(CMCS-PCEATS) as ionophore was constructed for potentiometric determination of aluminum (III) and the chelation between the ionophore and the aluminum (III) ions at the electrode surface was characterized using SEM, EDX, and IR analysis. Thermal stability of the prepared electrode before and after chelation with the metal ion was investigated. The highest performance was obtained with the electrode modified with 10 mg of the prepared copolymers plasticized with TCP (electrode I). Under the optimized provision, the electrode I shows Nernstian slope of 19.9?±?0.36 mV decade^??1 over the concentration range from 1.0?×?10^??6 to 1.0?×?10^??2 mol L^??1 with a detection limit of 1.0?×?10^??6 mol L^??1 and pH ranges from 3 to 8. The paste is enough stable for 37 days without any detected change in the potential. The proposed method is more potent in determination of Al(III) in both real water and pharmaceutical samples potentiometrically. The results obtained agreed with those obtained with spectrophotometer and inductive coupled plasma (ICP).