水中受激布里渊散射微弱Stokes信号光的高增益放大

采用脉冲宽度为7.2 ns的种子光注入式倍频Nd:YAG脉冲激光器,以CS₂为放大介质,实验并理论研究了水中受激布里渊散射微弱Stokes光的信号增益随延迟时间、放大器池长、抽运光能量的变化规律. 结果表明,当抽运光脉冲相对信号光脉冲延迟进入放大器,且延迟时间为脉冲宽度的一半,抽运光能量略低于介质受激布里渊散射阈值,选择合适的放大器池长可获得最佳的信号增益. 适当选择抽运光能量,亦可实现微弱信号光的线性放大. 实验中采用独立双池放大系统,当水中Stokes信号光的能量为1 pJ时,信 关键词： 布里渊放大器 信号增益 延迟时间 抽运光能量     

Polarization dependence of gain and amplified spontaneous Brillouin scattering noise analysis for fiber Brillouin amplifier

The polarization dependences of gain and amplified spontaneous Brillouin scattering(ABS) noise for fiber Brillouin amplifier(FBA) are analyzed through theories, simulations, and experiments.Modified vector propagation equations for calculating the gain of the probe signal and the ABS noise are derived and analyzed in the Stokes spaces.In simulations and experiments, we prove that the gain of the probe signal and the ABS noise are strongly dependent on the relative state of polarization(SOP) of the pump and probe signals.The closer the relative SOP of the pump and probe signals is, the more obvious ABS noise suppression effect will be brought by increasing the power of the input probe signal.     

Dynamics of the Stokes pulse in a Brillouin amplifier

We show that the output Stoke pulse from a continuously (CW) pumped stimulated Brillouin scattering (SBS) amplifier is the sum of the transmitted input Stokes pulse, which propagates undistorted through the medium without amplification and additional delay, and of a Stokes shifted pump signal reflected by the electrostrictively induced acoustic wave, which contributes to the Stokes output signal with a delay determined by the time required for build up of the acoustic wave.     

High-gain and low-distortion Brillouin amplification based on pump multi-frequency intensity modulation

Using a pump with a multi-line spectrum to broaden the Brillouin gain bandwidth is an effective way to achieve lowdistortion amplification with high gain. Here, we theoretically and experimentally investigate the generation of a broadband Brillouin gain spectrum based on multi-frequency intensity modulation in an optical fiber. The arbitrary bandwidth of the Brillouin gain spectrum of stimulated Brillouin scattering(SBS) can be obtained as expected. In our experiment, a broadband Brillouin gain spectrum with a bandwidth of about 200 MHz is demonstrated. We also achieve a low-distortion amplification of a weak signal, whose maximum magnification is 65 d B for a-68-dBm input power signal.     

A new method for measuring the threshold of stimulated Brillouin scattering

A new method for measuring the threshold of stimulated Brillouin scattering (SBS) based on the generation location of a Stokes beam is proposed for the first time to our knowledge. The length of the medium cell is selected to be longer than the free gain length of pump pulses in the Brillouin medium. The reflected light from a certain mirror in front of the medium cell is chosen as the reference beam, and the SBS threshold is measured by the "jump" of the delay between the Stokes beam and the reference beam. An 8-ns Q-switched single-longitudinal-mode pulse is used as the pump and the typical SBS medium FC-72 is selected as the nonlinear medium in our experiment. The SBS threshold intensity is measured to be 173-178 mW/cm 2 , which is consistent with existing results measured with the transmitted energy limiting method.     

光纤放大器中的受激布里渊散射阈值

 从受激布里渊散射(SBS)耦合波理论出发,根据双包层光纤放大器中的受激布里渊散射阈值模型,理论仿真了信号带宽、纤芯直径、放大器增益对SBS阈值的影响,并从实验上研究了单频百纳秒脉冲信号在掺镱双包层光纤放大器中的受激布里渊散射现象。实验中输入脉冲信号重复频率1 Hz,脉宽200 ns,对不同的输入脉冲信号放大,前向放大脉冲在脉冲能量660 nJ、峰值功率3.3 W时出现畸变,产生后向SBS窄脉冲,达到了SBS阈值,实验计算的SBS阈值与理论分析结果基本一致。     

布里渊放大器中Stokes光的高增益放大

微小Stokes信号光在布里渊放大器中得到放大,当Stokes信号光强度为015mj时,增益系数达到67。Stokes光增益决定于Stokes信号光强度及放大池中泵光与Stokes光的耦合程度,小信号Stokes光将得到较大的增益,并能得到较好的相位共轭效果     

Time delay enhancement in stimulated-Brillouin-scattering-based slow-light systems

We show a simple method of time delay enhancement in slow-light systems based on the effect of stimulated Brillouin scattering. The method is based on the reduction of the absolute Brillouin gain by a loss produced by an additional pump laser. With this method we achieved pulse delays of nearly 100 ns in a standard single-mode fiber. In the presented approach the delay or acceleration of optical signals is decoupled from their amplification or attenuation, which allows the adaptation of the pulse amplitudes to the given application.     

同轴正交偏振双脉冲序列受激布里渊散射抽运放大的实现方法

利用受激布里渊散射放大时抽运光与种子光可以有一时间延迟的特性,设计了一个同轴传播正交偏振双脉冲序列的偏振控制装置,使同轴传播的两个正交偏振脉冲光束在放大时具有相同的偏振态,从而实现了两束光的抽运放大.     

DCM荧光增强C3H6O 受激拉曼散射（SRS）的增益特性研究

报道荧光染料DCM对丙酮SRS的高效放大, 研究了DCM中Stokes波的增益特性. 改变DCM乙醇溶 液浓度，变化进入DCM的Stokes光强度以及抽运激光功率，测量并分析了Stokes波增益与上 述条件的关系. 研究结果发现，当DCM浓度为 2×10^-4mol/L时，Stokes波 获得最大功 率增益达到57；抽运激光功率增加或进入DCM的Stokes信号增强时Stokes波输出增强，但 过强的Stokes 信号将导致增益饱和. 关键词： 受激拉曼散射 荧光增强Stokes波 丙酮 DCM     

Effect of Brillouin slow light on distributed Brillouin fiber sensors

The effect of Brillouin slow light on distributed Brillouin fiber sensors (DBFSs) is studied. We demonstrate Brillouin slow light for a 1.2 ns pulse with peak powers (PS) from 3.3 to 56.2 mW on depletion of the pump power (PP) ranging from 1.3 to 83.2 mW in conventional optical fibers (SMF-28). Experiments show that, when pump power depletion is not negligible, for a given PP the Brillouin gain and delay time of a pulse decrease when PS increases in a long (> or =10 km) sensing fiber. The optimum pump beam depletion resulting from strong interaction of the pump and the probe in the fiber provides accurate temperature and strain information at a high spatial resolution. Our study reveals that at low PP the spatial resolution error caused by the pulse delay for a DBFS with centimeter spatial resolution is less than 5% of the pulse length.     

Long Optical Delay Lines Enhanced by Ring Configuration in Optical Fibres

A long optically controlled delay line enhanced by ring configuration is demonstrated by using the group-velocity control of signal pulses based on stimulated Brillouin scattering. In experiment, two optical fibre ring cavities are used： one is used as the Brillouin laser, providing single-mode Stokes wave as probe wave; the other is used as the Brillouin amplifier, working as slow light medium. We achieve a maximum time delay of 215ns using the ring Brillouin amplifier, five times larger than the input probe pulse width of 40ns. In the meantime, a considerable pulse broadening is observed, which agrees well with the theoretical prediction based on linear theory.     

Nonlinear phase shifts of modulated light waves with slow and superluminal group delay in stimulated Brillouin scattering

Brillouin amplification with counterpropagating modulated pump and Stokes light leads to nonlinear modulation-phase shifts of the interacting intensity waves. This is due to a partial transformation of the nonmodulated light component at the input into modulated light at the output as a result of a mixing process with the counterpropagating modulated component of the pump and results in an advance or delay of the input modulation. This occurs for interactions over less than half of a modulation wavelength. Milliwatts of power in a kilometer of standard single-mode fiber give significant tunability of the modulation phase.     

水中微弱光散射布里渊频谱选择性光放大研究

提出利用布里渊放大技术对水中微弱光散射信号进行频谱选择性光放大的方法.根据频率失谐布里渊放大理论模型，分析了Stokes种子光的线宽及频率失谐对布里渊放大的影响，研究了种子光放大率随水温及其功率密度变化的规律，理论和实验符合较好.研究表明，相同频率失谐时，线宽较大的种子光信号放大率更高.选取20℃的CS₂为放大介质，不同温度海水产生的Stokes种子光信号均能得到有效的布里渊放大.相同抽运光功率密度情况下，种子光的放大率随其功率密度的增加而减小，当种子光能量约为5μJ时，其放大率达10²以上.     

Amplification of short laser pulses by Raman backscattering in capillary plasmas

Short laser pulses can be significantly amplified in the process of Raman backscattering in plasma inside an oversized dielectric capillary. A dielectric capillary allows obtaining high intensities of the output radiation by sustaining efficient amplification at large distances compared to the diffraction length. The efficiency of the interaction between the pump wave and the amplified pulse is shown not to be critically sensitive to the transverse structure of the wave fields. For a quasi-single-mode initial seed pulse and a low pump intensity, the amplified pulse tends to preserve its transverse structure due to nonlinear competition of the capillary eigen-modes. At a high power of the pump wave, multimode amplification always takes place but the growth of the front peak of the pulse still follows the one-dimensional model. The Raman backscattering instability of the pump wave resulting in the noise amplification can be suppressed in detuned interaction by chirping the pump wave or arranging an inhomogeneous plasma density profile along the trace of amplification. The efficiency of the desired pulse amplification does not significantly depend on detuning in the case of a smooth detuning profile. Density inhomogeneities are shown to exert less influence on the amplification within a capillary than in the one-dimensional problem. Parameters of a future experiment on the Raman amplification of a short laser pulse inside a capillary are proposed.     

Slow and fast light based on SBS with the spectrum tailoring

In this paper, slow and fast light of a signal pulse of nanosecond duration are achieved in the same experimental device by using band-pass filters to tailor the spectra of spontaneous Brillouin scattering (SPBS) coming from 50 km single-mode optical fibers (SMF) as the pump light. The phase matching condition of slow and fast light is satisfied by changing wavelengths of band-pass filters .In our experiment, we obtain the tunable delay time for various signal pulses range from 1 ns to 20 ns. By increasing the power of the pump field to 16 mW, a 1 ns signal pulse is delayed 1.5 ns and is advanced 1.0 ns respectively, while the signal pulse almost has no distortion. The experiment has demonstrated that larger relative pulse delay of slow and fast light can be obtained in the same experimental setup when pump power is lower.     

Intensity correlation time of a single-mode laser driven by two coloured noises with coloured cross-correlation with direct signal modulation

In this paper, the intensity correlation time T is studied for the gain-noise model of a single-mode laser driven by coloured pump noise and coloured quantum noise with coloured cross-correlation with a direct signal modulation. By using the linear approximation method, it is found that when the pump noise is modulated directly by a signal, the effects of the cross-correlation between the pump noise and the quantum noise will disappear. In addition, there exists a maximum (i.e. resonance) in the curve of the intensity correlation time $T$ versus the pump noise self-correlation time \tau¹. Furthermore, when \tau¹\le\tau², the intensity correlation time T increases monotonically with the increase of $D$ and decreases monotonically with the increase of Q, but when \tau¹>\tau², the intensity correlation time T increases monotonically with the increase of Q and decreases monotonically with the increase of D.     

Fundamental amplitude noise limitations to supercontinuum spectra generated in a microstructured fiber

Broadband supercontinuum spectra are generated in a microstructured fiber using femtosecond laser pulses. Noise properties of these spectra are studied through experiments and numerical simulations based on a generalized stochastic nonlinear Schrödinger equation. In particular, the relative intensity noise as a function of wavelength across the supercontinuum is measured over a wide range of input pulse parameters, and experimental results and simulations are shown to be in good quantitative agreement. For certain input pulse parameters, amplitude fluctuations as large as 50% are observed. The simulations clarify that the intensity noise on the supercontinuum arises from the amplification of two noise inputs during propagation – quantum-limited shot noise on the input pulse, and spontaneous Raman scattering in the fiber. The amplification factor is a sensitive function of the input pulse parameters. Short input pulses are critical for the generation of very broad supercontinua with low noise. PACS 42.50.Lc; 42.65.Re; 42.81.Dp; 02.60.CbAn Erratum to this article can be found at     

Weak laser pulse signal amplification based on a fiber Brillouin amplifier

We propose a high-gain and frequency-selective amplifier for a weak optical signal based on stimulated Brillouin scattering in a single mode fiber. To be able to satisfy the needs of high gain and high signal-to-noise ratio laser pulse amplification, different fiber lengths and core diameters are used to fulfill this experiment. In the experiment, a 430 nW(peak power) pulsed signal is amplified by 70 dB with a signal-to-noise ratio of 14 dB. The small size, high gain, low cost, and low noise of the fiber Brillouin amplifier make it a promising weak signal amplification method for practical applications such as lidar.     

Theory of noise in a kilo-Hz cascaded high-energy Yb-doped nanosecond pulsed fiber amplifier

A theoretical analysis of noise in a high-power cascaded fiber amplifier is presented. Unlike the noise theory in low power communication, the noise of a high power system is redefined as the leaked output energy between pulses with coherent beat noise uncounted. This definition is more appropriate for high power usage in which the pulse energy receives more attention than the pulse shape integrity. Then the low power pre-amplifying stages are considered as linear amplification and analyzed by linear theory. In the high-power amplification stages, the inversion is assumed to recover linearly in the time interval between pulses. The time shape of the output pulse is different from that of the input signal because of different gains at the front and back ends of the pulse. Then, a criterion is provided to distinguish the nonlinear and linear amplifications based on the signal-to-noise ratio （SNR） analysis. Then, an experiment that shows that the output SNR actually drops off in nonlinear amplification is performed. The change in the noise factor can be well evaluated by pulse shape distortion.