Sol-Gel Fabrication and Properties of Silica Cores of Optical Fibers Doped with Yb3+, Er3+, Al2 O3 or TiO2

Optical cores of preforms for drawing optical fibers doped with Er3+ and Yb3+ were fabricated by the sol-gel method with the aim of increasing the thickness of glass layers coated in a single coating cycle and to determine the relation between the preparation conditions and optical properties of the fibers. Al2O3-P2O5-SiO2 and TiO2-P2O5-SiO2 glasses have been studied as matrices for entrapping the rare-earth elements. Input sols have been prepared from silicon and titanium alkoxides, AlCl3, ErCl3, YbCl3, POCl3, water and a modifier under acidic catalysis of HCl. The sols were coated on the inner wall of a silica substrate tube and the gel layers were sintered at high temperatures up to 2000°C after which the tube was collapsed into the preform. Continuous and homogenous glass films with the maximum thickness of about 8 m were fabricated. The influence of high-temperature heat treatment of the layers on their composition and optical attenuation was observed. The amplified stimulated emission of Er3+ around 1.55 m was measured under the excitation of the fibers by an Nd : YAG laser at 1.064 m.     

MgF2 Xerogels

MgF₂ protective and antireflective coatings have been conventionally produced by sputtering or chemical vapour deposition CVD [1, 2], but here sol-gel routes to MgF₂ are explored. MgF_2(M) and MgF_2(E) were prepared using an alkoxide:HF:ROH mole ratio of 1:2:200 with methanol and ethanol respectively. All sols were stable for over a year. X-ray diffraction confirmed the presence of MgF₂ in samples (but also traces of MgO), and X-ray photoelectron spectroscopy suggested some F deficiency in the surface. Nevertheless, the MgF₂ xerogels had surface areas and porosities that were very high and this may be used to advantage in coatings or sensors.     

Study of Hybrid Silica-Polyethyleneglycol Xerogels by Eu3+ Luminescence Spectroscopy

Good optical quality Eu3+-doped silica-polyethyleneglycol hybrids were prepared by the sol-gel process. Thermomechanical analysis showed an increase of the glass transition temperature, due to the stiffness of the polymeric network, as the amount of Eu3+ increased. Europium luminescent properties were used to study structural evolution during the sol-gel transition. For lower doping concentrations dried gels present statistical distributions of Eu3+, typical of an amorphous environment, while for higher concentrations a crystalline-like environment of Eu3+ was observed. A broad emission band was observed in the visible part of the electromagnetic spectrum and assigned to the intrinsic emission from the hybrid polymeric network.     

Silica-based sol-gel films doped with active elements

The preparation of glassy films doped with rare earth ions is important for planar waveguide fabrication in active integrated optic devices. The sol-gel process is a promising route for the preparation of such films and the eventual overcoming of the problem of rare earth clustering. In the present work, both SiO₂ and 90SiO₂-10TiO₂ films were prepared by spin coating on silica glass or single crystal silicon substrates and they were doped with neodymium in a Nd/Si atomic ratio up to 15%, using NdCl₃ as precursor. These films were subjected to selected heat treatments and their thickness and infrared spectra were measured. The refractive index and porosity were also determined for some of the samples. Visible absorption spectra were then measured in bulk gels, due to the insufficient optical path of the films.     

Er3+-doped Multicomponent Silicate Glass Planar Waveguides Prepared by Sol-Gel Processing

Erbium doped silica-titania planar waveguides, co-doped with ytterbium and aluminum, have been prepared by sol-gel processing, using multilayer spin-coating deposition on silicon or silica glass substrates. The Er3+ doping level varied between 0 and 2 at.%, while Yb3+ varied from 0 to 3 at.%. Aluminum was incorporated up to 15 at.% Al and it was found to have no significant effect on the refractive index of the silica-titania (80 : 20 mol%) matrix. The Er3+ fluorescence emission was flat within ±0.5 dB, between 1520 and 1560 nm. The corresponding 4I13/2 metastable level lifetime was found to decrease from 6.1 to 3.5 ms, as the Er concentration increased from 0.1 to 0.5 at.%, for films co-doped with 0.5 at.% Yb and 10 at.% Al and the fluorescence decay was essentially single exponential below a Er quenching concentration of 0.5 at.% (1.1 × 1020 ions/cm3). The lifetime appears to be limited by Er-Er interactions at higher rare-earth ion concentrations and by residual OH species in the sol-gel derived waveguides. Vacuum heat treatment at a temperature near 570°C was somewhat effective in increasing the Er fluorescence lifetime, whereas reactive atmosphere processing in CCl4 or Cl2 at a similar temperature appeared to be less effective.     

M2+(M=Cu、Cd、Ag、Fe)掺杂氧化锌纳米粉晶的抗菌性能

采用柠檬酸溶胶-凝胶法制备了ZnO及M²⁺掺杂ZnO纳米粉晶(M=Cu、Cd、Ag、Fe),用现代测试技术表征了样品的组成、结构和形貌,以大肠杆菌(Escherichia coli)、金黄色葡萄球菌(Staphylococcus aureus)和白色念珠菌(Candida albicans)为测试菌株,用抑菌圈、最小抑菌浓度和最小杀菌浓度等方法研究了样品在日光照射下的抗菌活性。结果表明,与母体ZnO相比,Cu、Ag、Cd掺杂样品的抗菌性能明显地增强,这可能是由于掺杂金属离子置换Zn²⁺生成了晶格缺陷和电荷缺陷,阻止了光生电子和光生空穴对的复合从而增强了光催化活性和抗菌活性。     

Analytical Properties of Gaize- and Silicate Glue-Based Xerogels with Immobilized Chrome Azurol S

A method is proposed for the synthesis of silicic acid xerogels based on opoka aluminosilicate (gaize) and silicate glue. The physicochemical properties of xerogels were studied. The complexation of Be(II) with immobilized Chrome Azurol S was studied by electronic absorption and diffuse-reflection spectrometry and solid-phase spectrophotometry. Test procedures were developed for determining Be(II) and Al(III) in waters and soils.     

M~(2+)(M=Cu、Cd、Ag、Fe)掺杂氧化锌纳米粉晶的抗菌性能

采用柠檬酸溶胶-凝胶法制备了ZnO及M2+掺杂ZnO纳米粉晶(M=Cu、Cd、Ag、Fe),用现代测试技术表征了样品的组成、结构和形貌,以大肠杆菌(Escherichia coli)、金黄色葡萄球菌(Staphylococcus aureus)和白色念珠菌(Candida albicans)为测试菌株,用抑菌圈、最小抑菌浓度和最小杀菌浓度等方法研究了样品在日光照射下的抗菌活性。结果表明,与母体ZnO相比,Cu、Ag、Cd掺杂样品的抗菌性能明显地增强,这可能是由于掺杂金属离子置换Zn2+生成了晶格缺陷和电荷缺陷,阻止了光生电子和光生空穴对的复合从而增强了光催化活性和抗菌活性。     

Induced Chirality in Canthaxanthin Aggregates Reveals Multiple Levels of Supramolecular Organization

Carotenoids tend to form supramolecular aggregates via non-covalent interactions where the chirality of individual molecules is amplified to the macroscopic level. We show that this can also be achieved for non-chiral carotenoid monomers interacting with polysaccharides. The chirality induction in canthaxanthin (CAX), caused by heparin (HP) and hyaluronic acid (HA), was monitored by chiroptical spectroscopy. Electronic circular dichroism (ECD) and Raman optical activity (ROA) spectra indicated the presence of multiple carotenoid formations, such as H- and J-type aggregates. This is consistent with molecular dynamics (MD) and density functional theory (DFT) simulations of the supramolecular structures and their spectroscopic response.     

Er3+/Yb3+ Co-Activated Silica-Alumina Monolithic Xerogels

Monolithic silica xerogels doped with different concentrations of Er³⁺, Yb³⁺ and Al³⁺ were prepared by sol-gel route. Densification was achieved by thermal treatment in air at 950°C for 120 h with a heating rate of 0.1°C/min. We studied the luminescence properties of the ⁴I_13/2 ⁴I_15/2 emission band of Er³⁺ as a function of the Al/Er/Yb concentration and we paid particular attention to the alumina effects. Raman spectroscopy and Vis-NIR absorption were used to monitor the degree of densification of the glasses and the residual OH content.     

Optically Active Conjugated Polymer from Solvent Chirality Transfer Polymerization in Monoterpenes

Disubstituted acetylene monomers [1,2‐diphenylacetylenes (DPAs: DPA‐pC1, DPA‐mC1, DPA‐pC8); 1‐phenyl‐2‐hexylacetylene (PHA‐pC1)] are tested for asymmetric polymerization in chiral monoterpenes used as solvents and compared with the corresponding monosubstituted acetylene monomer [1‐phenylacetylene (PA‐pC1)]. DPA‐pC1 containing a trimethylsilyl group in the para‐position of the phenyl ring produces an optically active polymer with a large Cotton effect, despite the absence of a stereogenic center. The polymer sample obtained by polymerization in 87% ee (–)‐α‐pinene shows the strongest CD signal (g_CD value at 385 nm: ∼3.2 × 10⁻³). The Cotton bands of the polymers obtained in (–)‐ and (+)‐α‐pinenes show the opposite sign in the CD signals. Theoretical calculations show that only the cis‐cisoid model adopts a helical conformation. A time‐correlated single photon counting experiment shows that the emission of the chiral polymer originates from a virtually single excited species with a 98% component fraction. This polymer solution does not show any significant decrease in g_CD value over a wide temperature range of 20 to 80 °C. No noticeable decrease in the g_CD value is detected when the polymer solution is kept at relatively low temperatures for a prolonged period (35 d). In contrast, the other polymers show no CD signal.

     

Thermal Treatment of Sol-Gel Derived Nickel Oxide Xerogels

Very fine nickel hydroxide and oxide xerogel powders were prepared using a new sol-gel synthesis procedure in which nickel ethoxide was produced through the reaction of nickel chloride, as a precursor, with sodium ethoxide in dehydrated ethanol, followed by the hydrolysis of nickel ethoxide with ammonia and drying the resulting hydrogel under subcritical pressures to form the xerogel. The effects of thermal treatment on the surface area, pore volume, crystallinity and particle structure of the resulting xerogels were investigated and found to have significant effects on all of these properties. Overall, the xerogel remained amorphous as Ni(OH)₂ space up to 200°C, with little change in the surface area and pore volume. At 250°C, the Ni(OH)₂ began to decompose and form crystalline NiO with the uniformity of the crystals increasing with an increase in temperature. The surface area and pore volume decreased sharply when increasingthe temperature beyond 250°C; this was the temperature where maximums of about 270 m²/g and 0.33 cm³/g were exhibited by this composite amorphous Ni(OH)₂ and crystalline NiO xerogel powders. At the higher calcination temperatures, very uniform NiO crystals with average crystallite sizes of 1.7 nm and 14.5 nm were obtained at 400 and 600°C, respectively.     

V2O5/TiO2 Catalytic Xerogels Raman and EPR Studies

Raman spectroscopy and Electron Paramagnetic Resonance (EPR) studies were performed on a series of V₂O₅/TiO₂ catalysts prepared by a modified sol-gel method in order to identify the vanadium species. Two species of surface vanadium were identified by Raman measurements, monomeric vanadyls and polymeric vanadates. Monomeric vanadyls are characterized by a narrow Raman band at 1030 cm^–1 and polymeric vanadates by two broad bands in the region from 900 to 960 cm^–1 and 770 to 850 cm^–1. The Raman spectra do not exhibit characteristic peaks of crystalline V₂O₅. These results are in agreement with those of X-ray Diffractometry (XRD) and Fourier Transform Infrared (FT-IR) previously reported (C.B. Rodella et al., J. Sol-Gel Sci. Techn., submitted). At least three families of V⁴⁺ ions were identified by EPR investigations. The analysis of the EPR spectra suggests that isolated V⁴⁺ ions are located in sites with octahedral symmetry substituting for Ti⁴⁺ ions in the rutile structure. Magnetically interacting V⁴⁺ ions are also present as pairs or clusters giving rise to a broad and structureless EPR line. At higher concentration of V₂O₅, a partial oxidation of V⁴⁺ to V⁵⁺ is apparent from the EPR results.     

表面活性物质对SiO2干凝胶中甲基橙变色反应的影响

掺杂;表面活性物质对SiO2干凝胶中甲基橙变色反应的影响     

Si掺杂TiO2纤维的溶胶-凝胶法制备及其光催化活性

采用溶胶-凝胶法并结合水蒸气活化制备了Si掺杂TiO₂纤维, 通过TG-DSC, XRD, FT-IR, UV-Vis-DRS, N₂吸附-脱附, SEM等手段对纤维样品的结构参数及其表面形貌进行了表征, 并以活性艳红X-3B模拟废水体系评价了其光催化活性．结果表明, 与纯TiO₂产物相比, 适量Si掺杂制得的产物是具有丰富介孔结构的TiO₂长纤维, 不仅热稳定性和晶型稳定性俱佳, 而且光催化活性得以显著提高, 经900 ℃热处理后仍能保持结晶完好的锐钛矿相; 在Si/Ti摩尔比为0.15时, 其比表面积和孔容最大, 光催化活性最佳, 该纤维作为光催化剂反应75 min, 水中X-3B的降解率可达99.6%.     

Effects of pH and Dye Concentration on the Optical and Structural Properties of Coumarin-4 Dye-Doped SiO2-PDMS Xerogels

Optical and structural properties of coumarin-4 dye-doped SiO₂-PDMS xerogels synthesized by acid catalyzed (one-step) and acid-base catalyzed (two-step) sol-gel routes with varying pH (0.6 to 7) and dye content ( 5 × 10^–4 to 5 × 10^–2 mole) are reported. Spectroscopic methods such as photo-luminescence, FT-IR and FT-Raman were used for characterizations. The acid catalyzed xerogels prepared with pH < 2.5 exhibited two fluorescence peaks, I at 390 nm and II at 480 nm. The acid-base catalyzed xerogels synthesized with pH < 2.5 also exhibited two peaks, I at 400 nm and II at 475 nm. Peak II was not observed for the samples with pH 2.5. This phenomenon was attributed to the existence of pH dependent different forms of coumarin-4 molecule. The concentration-quenching phenomenon was observed for the acid catalyzed xerogels prepared with different dye concentration. TheFT-IR spectra indicated the existence of hydrogen bonds between the carbonyl groups of dye molecules and the silanol groups of gel matrix. The hydrogen bonding was the highest for the samples with the extremity pH, 0.6 and 7, resulting in the highest dye/gel matrix interactions, hence, the highest fluorescence peaks. The Raman studies indicated that the samples prepared with pH < 2.5 possessed relatively more number of 3-membered siloxane rings than 4-membered siloxane rings. The ring statistics was reversed for the samples with pH > 2.5. The number of silanol groups was higher for the samples with pH > 2.5.     

Amino-Modified Silicate Xerogels Complexed with Cu(II) as Catalyst Precursors. Coordination State and Thermal Decomposition

The sol-gel process is a useful method for preparing two series of organically and co-ordinately modified xerogels of the types [CuN _n ]·N _5–n ·5xSiO_4/2 (n < 4) and [Cu(N–N)_n]·(N–N)_2–n ·2x SiO_4/2(n 2), where N = NH₂(CH₂)₃ SiO_3/2, N–N = NH₂(CH₂)₂NH·(CH₂)₃SiO_3/2 and x = [SiO_4/2]/[N] or [SiO_4/2]/[N–N]. The amino groups in the materials are coordinately active and participate partly in the coordination sphere of Cu(II) ions. The composition of the coordination sphere can be varied with the SiO_4/2 content and also as a result of the thermal decomposition of the organic residues at higher temperatures.Because the xerogel materials are considered to be catalyst precursors, this study is focused on their coordination and thermal properties. The prepared xerogels, such as silica, aminated silicates with N and N–N, as well as those entities complexed with Cu(II), were characterised by FT-IR spectroscopy. During gelation and thermal decomposition the materials were analysed by electron paramagnetic resonance (EPR) spectroscopy. The xerogels were additionally studied by UV-Vis absorption spectroscopy. The gaseous products of the thermal decomposition of these materials in an Ar atmosphere were investigated by the use of FT-IR spectroscopy coupled with TG and DTG thermal analysis. These data were complemented by temperature-programmed decomposition (TPDec) in a 2% O₂ + 98% Ar stream coupled with quadrupole mass spectroscopy.     

Preparation of Transparent, Partially-Crystallized BaTiO3 Monolithic Xerogels by Sol-Gel Processing

Transparent, partially-crystallized nanostructured barium titanate (BaTiO3) monolithic xerogels (dried at 90°C) have been successfully synthesized via hydrolysis of Ba, Ti alkoxide precursor solutions in a concentration range of 1.0 mol/l with addition of water with a molar ratio of H2O/Ba 6.3. Transparent monolithic xerogels obtained from a precursor solution of 1.0 mol/l remained transparent even after firing at 500°C in oxygen, although the degree of their transparency was considerably decreased. Firing at temperatures above 500°C yielded translucent ceramics of BaTiO3, and ultimately, firing above 600°C resulted in normal opaque ceramic bodies. Those obtained from a more concentrated precursor solution of 1.2 mol/l were, on the other hand, still transparent after firing at 600°C in oxygen, and turned opaque at 700°C. The results demonstrate that the materials retained their transparency even after pyrolysis of organic compounds involving exothermic oxidation at temperatures in the range of 200 to 400°C. The densification behavior of transparent BaTiO3 monolithic xerogels obtained was found to be excellent; for example, those derived from a 1.0 mol/l precursor solution could be sintered to form monolithic BaTiO3 ceramics with a relative sintered density of about 94% and an average grain size of 1 m by firing at 1100°C for 2 h in oxygen.     

Cobalt Oxide/Silica Xerogels Powders: X-Ray Diffraction,Infrared and Visible Absorption Studies

Using x-ray diffraction, infrared and visible absorption spectroscopies we have studied: silica xerogel powders when cobalt nitrate is incorporated and mainly the evolution of the precipitated cobalt species in the SiO₂ matrix. Samples containing cobalt nitrate and prepared with a molar ratio of H₂O/TEOS of 11.67 were studied as a function of annealing temperature. It was found that the added element has a remarkable influence on the final structure of this kind of samples and at relatively high temperatures the cobalt compounds react with the silica matrix forming a cobalt silicate.